Amada America Inc. 7025 Firestone Blvd. Buena Park CA. 90621 Phone: (714) 739 2111 Fax: (714) 739 4099 Email info@amada.com Print Date 03/01/2001 Revision 4.0 This document available on the World Wide Web at http://www.amada.com Page 1 of 9
Warning Qualified personnel must complete all work. Do not apply power to the Pega 345 until an A.E.S.I. (Amada Engineering and Service Incorporated) Engineer is present and has instructed you to do so. Not all information required for proper installation, of the Pega 345 is included with this document. Specific details for proper installation are found in the document Pega 345 with 04PC User Pre-installation Guide available at the Amada America Internet web site at http://www.amada.com. Considerable effort has been made to ensure that this manual is free of inaccuracies and omissions. However, as we are constantly improving our product, some of the data contained herein may be out of date. Please check our Internet site, http://www.amada.com, for the latest release of this document. Print Date 03/01/2001 Revision 4.0 This document available on the World Wide Web at http://www.amada.com Page 2 of 9
Table Of Contents Planning the Location of the Machine...4 Plan View - Pega 345 Queen...5 Plan View - Pega 345 Queen with V345hs Conveyor...6 Plan View - Pega 345 Queen with V345hs Conveyor and MP1225 Loader...7 End View - Pega 345 Queen...8 Elevation View - Pega 345 Queen...9 Print Date 03/01/2001 Revision 4.0 This document available on the World Wide Web at http://www.amada.com Page 3 of 9
Planning the Location of the Machine The following diagrams provide the details for positioning your new machine.! Not all information required for proper installation, of the Pega 345 is included with this document. Specific details for proper installation are found in the document Pega 345 with 04PC User Pre-installation Guide available at the Amada America Internet web site at http://www.amada.com.! No obstacles are allowed in the worksheet travel area and the ceiling must be at least 40" above the Pega 345 Queen.! All of the Recommended Safety / Maintenance areas should be used, but you must at least ensure that the doors of the 04PC control unit can be opened. Any reduction of the Recommended Safety / Maintenance areas may increase the possibility of personnel injury and increase the time and cost of installation or maintenance.! The Pega 345 Queen and 04PC control must be protected from direct sunlight or other heat sources. Exposure to direct heating sources such as infrared heaters have been shown to affect punch and die alignment. Print Date 03/01/2001 Revision 4.0 This document available on the World Wide Web at http://www.amada.com Page 4 of 9
Plan View - Pega 345 Queen Electrical Requirements E1 Pega 345 Queen 230 / 460 / 3 / 60 ±10% 18 kva 46 amps @ 230 / 3 / 60 VAC 23 amps @ 460 / 3 / 60 VAC Compressed Air Requirements 27.56" A1 Pega 345 Operator Control Station 80 psi @ 8.8 ft3/min. Power Supply 49.21" 04PC Control 310.84" Recomended Safety / Maintenance Area 40" From All Components 162.52" Pega 345 Queen Length 80" Maximum Travel Area 40" Material 58.47" 39.37" Work Range Y-axis Zero 19.10" 11.56" E1 45" Minimum 56" Maximum Pega 345Q 24.05" A1 55.12" 54.73" 109.85" Pega 345 Queen Width 200" Maximum Travel Area 100" Material 280.00" Recomended Safety / Maintenance Area 40" From All Components Print Date 03/01/2001 Revision 4.0 This document available on the World Wide Web at http://www.amada.com Page 5 of 9
Plan View - Pega 345 Queen with V345hs Conveyor Electrical Requirements E1 Pega 345 Queen 230 / 460 / 3 / 60 ±10% 18 kva 46 amps @ 230 / 3 / 60 VAC 23 amps @ 460 / 3 / 60 VAC E2 P345hs Conveyor 208-230 / 460 / 3 / 60 ±10%.8 kva 2.1 amps @ 208 / 3/ 60 VAC 2.0 amps @ 230 / 3 / 60 VAC 1.0 amps @ 460 / 3 / 60 VAC Compressed Air Requirements A1 Pega 345 Operator Control Station 80 psi @ 8.8 ft3/min. 383.84" Recomended Safety / Maintenance Area 40" From All Components 162.52" Pega 345 Queen Length 80" Maximum Travel Area 40" Material 58.47" 39.37" Work Range 24.05" Y-axis Zero A1 19.10" 11.56" 49.21" E1 04PC Control 27.56" 45" Minimum 56" Maximum Pega 345Q 73.00" E2 P345hs 46.77" Access required this area for 55.12" 54.73" 109.85" Pega 345 Queen Width 200" Maximum Travel Area 100" Material 280.00" Recomended Safety / Maintenance Area 40" From All Components Print Date 03/01/2001 Revision 4.0 This document available on the World Wide Web at http://www.amada.com Page 6 of 9
Plan View - Pega 345 Queen with V345hs Conveyor and MP1225 Loader Electrical Requirements E1 Pega 345 Queen 230 / 460 / 3 / 60 ±10% 18 kva 46 amps @ 230 / 3 / 60 VAC 23 amps @ 460 / 3 / 60 VAC E2 P345hs Conveyor 208-230 / 460 / 3 / 60 ±10%.8 kva 2.1 amps @ 208 / 3/ 60 VAC 2.0 amps @ 230 / 3 / 60 VAC 1.0 amps @ 460 / 3 / 60 VAC E3 MP1225 Loader 200 / 3 / 60 ±10%, 10 Kva To operate at 230 / 460 VAC a step up transformer with the following service is required 29 amps @ 200 / 3 / 60 VAC 26 amps @ 230 / 3 / 60 VAC 13 amps @ 460 / 3 / 60 VAC Compressed Air Requirements A1 Pega 345 80 psi @ 8.8 ft3/min. A2 MP1225 Loader Operator Control Station 75 psi @ 31.8 ft3/min. 383.84" Recomended Safety / Maintenance Area 40" From All Components 162.52" Pega 345 Queen Length 80" Maximum Travel Area 40" Material 58.47" 39.37" Work Range 24.05" Y-axis Zero A1 19.10" 11.56" 49.21" 04PC Control E1 27.56" 0.06 mm Pega 345Q A2 45" Minimum 56" Maximum MP1225 Xformer E3 MP1225 Material Load Position 122.11" 67.52" 189.63" MP1225 Length E2 P345hs MP1225 Forklift access required this area for material / parts loading / unloading Access required this area for slug removal 55.12 54.73" 55.73" To Edge Of MP1225 109.85" Pega 345 Queen Width 200" Maximum Travel Area 100" Material 141.74" MP1225 Width 377.46" Recomended Safety / Maintenance Area 40" From All Components Print Date 03/01/2001 Revision 4.0 This document available on the World Wide Web at http://www.amada.com Page 7 of 9
End View - Pega 345 Queen 79.88" 111.00" 35.12"* Material Pass Line 29.53" 37.99" 54.72" 109.84" 55.12" *Dimension will change with installed options Print Date 03/01/2001 Revision 4.0 This document available on the World Wide Web at http://www.amada.com Page 8 of 9
Elevation View - Pega 345 Queen 47.24" Throat Depth 39.37" Work Area 62.99" 79.89" 35.12"* Material Pass Line Floor Line 33.47" 27.95" 9.84" 11.02" 7.99" 33.47" 27.56" 87.60" 162.52" Print Date 03/01/2001 Revision 4.0 This document available on the World Wide Web at http://www.amada.com Page 9 of 9