Explosion-Protected Pressure Switches To new ATEX Standard TECHNICAL DATA 0165 0340 0341 Degree of protection: IP 65 ATEX protection zone: 1 22 22 Switching power: 1 A / 250 VAC 0.25 A / 250 VDC 2 A / 250 VAC Body material: AlMgSi1 F28 Steel, zinc-plated (CrVI-free) Anodised aluminium Conductor cross-section: 3 x 0.75 mm 2 3 x 0.5 mm 2 Switching frequency: 200 / min. Temperature range: NBR, EPDM: -20 C +80 C; FKM: -5 C +80 C Mechanical life expectancy: Pressure rise rate: Vibration resistance: Shock resistance: Cable length: Hysteresis: 10 6 cycles 1 bar/ms 10 g / 5 200 Hz sine-wave 294 m/s 2 ; 14 ms half-sine-wave standard delivery 2 m with wire end sleeves 10 30% (not adjustable) 42
TECHNICAL DATA ATEX-certified for use in potentially-explosive atmospheres Compact design Micro-switch for reliable operation Switching point can be easily adjusted by user when switch is in operation Explosion-protected pressure switches are classified by ATEX and approved according to the type of combustible material that may be expected where they are to be used. The sub-divisions are: Gases and vapours Dusts Methane dust Our pressure switches are suitable for gases and vapours, or for dust according to type. They are not suitable for use in methane dust (mining applications). The table provides an overview of the sub-division into zones, equipment groups and equipment categories. Conditions in locations with potentially-explosive atmosphere Combustible material Gases Vapours Dusts Methane Dust Occurence of combustible material in location Present continuously, for long periods or frequently Designation of location with specified hazard Marking required on equipment to be used in the specified zone Equipment group Equipment category Zone 0 II 1G Occurs occasionally Zone 1 II 2G or 1G Unlikely to occur, and then only seldom or for short periods Present continuously, for long periods or frequently Zone 2 II 3G or 2G or 1G Zone 20 II 1D Occurs occasionally Zone 21 II 2D or 1D Occurs if accumulated dust is disturbed, and then only seldom or for short periods Zone 22 II 3D or 2D or 1D Mining industry I M1 Mining industry I M1 or M2 CE Marking Directives of the European Council Machinery Directive EMC Directive Low Voltage Directive ATEX Directive Equipment that falls under these directives must have a declaration of conformity and carry the CE marking. SUCO explosion-protected pressure switches fall under the ATEX Directive 94/9/EG. An EC Declaration of Conformity has been prepared for all products that fall under these directives and is kept on our premises. The catalogue pages for the relevant switches carry the CE marking. 43
0165 Diaphragm/piston pressure switches 250 V ATEX 0102 II 2G EEx d II C T6 / T5 (gas-protected zone 1) Aluminium body With changeover switch Max. voltage 250 V Overpressure safe to 200 / 600 bar 1) With female thread 0340 Diaphragm pressure switches ~2000 PG 9 1 6 ± 0.5 0165 448 14 001 5 50 ± 3.0 0165 449 14 001 200 1) 0341 Piston pressure switches 127 20 100 ± 3.0 5.0 0165 450 14 001 100 400 ± 5.0 9.0 0165 451 14 001 600 1) 15 5.5! Add figure for diaphragm/seal material 034X XXX XX X XXX 20 NBR Hydraulic / machine oil, turpentine, heating oil, air etc.1 = 1 G 1/4 EPDM Brake fluid, ozone, acetylene, hydrogen etc. = 2 FKM Hydraulic fluids (HFA, HFB, HFC, HFD), petrol/gasoline etc. = 3 Also available with switching point preset in our works. See page 42 for temperature ranges of diaphragm / seal materials Contact assignment: 1 = white 2 = green 4 = brown For further technical data, see page 43 44 Warning! When using with oxygen, the relevant accident-prevention regulations must be observed. In addition, we recommend that a maximum operating pressure of 10 bar is not exceeded. Piston-type pressure switches are only to a limited extent suitable for use with gases and oxygen. See explanation on page 5. 1) Static pressure, dynamic pressures should be 30 to 50% lower. These values refer to the hydraulic or pneumatic part of the pressure switch. Degree of protection IP65 The type approval does not apply without restriction to all environmental conditions. It is the responsibility of the user to check whether the connection complies with regulations other than those stated, and whether it can be used for special applications which could not be foreseen by us in advance.
0340/0341 Diaphragm/piston pressure switches 250 V ATEX II 3D IP65 T90 C (dust-protected zone 22) Zinc- plated steel body (CrVI-free) With changeover switch Max. voltage 250 V Overpressure safe to 300 / 600 bar 1) 0340 Diaphragm pressure switches With male thread 0.3 1.5 ± 0.2 0340 457 03 003 1 10 ± 0.5 1.0 0340 458 03 006 10 20 ± 1.0 0340 459 03 009 300 1) ~2000 Ø28.5 20 50 ± 2.0 0340 461 03 012 0341 Piston pressure switches 50 150 ± 5.0 0341 460 03 003 600 1)! Add figure for diaphragm/seal material 034X XXX XX X XXX 48 hex 27 9 NBR Hydraulic / machine oil, turpentine, heating oil, air etc.1 = 1 G 1/4 EPDM Brake fluid, ozone, acetylene, hydrogen etc. = 2 FKM Hydraulic fluids (HFA, HFB, HFC, HFD), petrol/gasoline etc. = 3 See page 42 for temperature ranges of diaphragm / seal materials Also available with switching point preset in our works. Contact assignment: 1 = black 2 = red 4 = white Warning! When using with oxygen, the relevant accident-prevention regulations must be observed. In addition, we recommend that a maximum operating pressure of 10 bar is not exceeded. Piston-type pressure switches are only to a limited extent suitable for use with gases and oxygen. See explanation on page 5. 1) Static pressure, dynamic pressures should be 30 to 50% lower. These values refer to the hydraulic or pneumatic part of the pressure switch. Degree of protection IP65 The type approval does not apply without restriction to all environmental conditions. It is the responsibility of the user to check whether the connection complies with regulations other than those stated, and whether it can be used for special applications which could not be foreseen by us in advance. 45 For further technical data, see page 43
Electrical Data 250 volt AC 50 / 60 Hz 4 amp (2 amp )* AC 12 24 volt DC 4 / 2 amp (2 / 1 amp)* DC 12 / DC 13 50 volt DC 2 / 1 amp (1 / 0.5 amp)* DC 12 / DC 13 75 volt DC 1 / 0.5 amp (0.5 / 0.25 amp)* DC 12 / DC 13 125 volt DC 0.3 / 0.2 amp (0.2 / 0.1 amp)* DC 12 / DC 13 250 volt DC 0.25 / 0.2 amp (0.15 / 0.1 amp)* DC 12 / DC 13 2.5 kv (4 kv)* 5 amp DC und 50 / 60 Hz Rated current of short-circuit protection: Up to 5 amp (up to 3.5 amp)* < 0.35 Nm 0140 0141 0180 0181 0183 0184 0185 0186 0187 * Figures in brackets apply to types 0140 and 0141 250 volt AC 50 / 60 Hz 5 amp AC 12 30 volt DC 3.5 / 3.5 amp DC 12 / DC 13 50 volt DC 2 / 1 amp DC 12 / DC 13 75 volt DC 1 / 0.5 amp DC 12 / DC 13 125 volt DC 0.3 / 0.2 amp DC 12 / DC 13 250 volt DC 0.35 / 0.2 amp DC 12 / DC 13 Rated current of short-circuit protection: 2.5 kv 6 amp DC and 50 / 60 Hz Up to 6.3 amp < 0.35 Nm 0150 0161 0162 0175 250 volt AC 50 / 60 Hz 2.5 amp AC 12 30 volt DC 2 / 2 amp DC 12 / DC 13 50 volt DC 1 / 0.5 amp DC 12 / DC 13 75 volt DC 0.75 / 0.4 amp DC 12 / DC 13 125 volt DC 0.3 / 0.2 amp DC 12 / DC 13 250 volt DC 0.3 / 0.2 amp DC 12 / DC 13 Rated current of short-circuit protection: 2.5 kv 6 amp DC and 50 / 60 Hz Up to 2.5 amp < 0.5 Nm 0159 The utilisation category describes among other things the voltages and currents and the way of load for our pressure switches according DIN EN 60947-5-1 AC 12 : Drive of resistive loads and semiconductor input circuits of optoelectronic couplers (e.g. PLC inputs) AC 14 : Drive of electromagnetic loads up to 72 VA DC 12 : Drive of resistive loads and semiconductor input circuits of optoelectronic couplers (e.g. PLC inputs) DC 13 : Drive of electromagnet Utilisation category