INSTALL GUIDE DOCUMENT NUMBER 56703 REVISION DATE 084 FIRMWARE OEM-AL(RS)-TL-[ADS-ALCA] HARDWARE ADS-ALCA ACCESSORIES ADS-USB (REQUIRED) TERMS OF USE: Automotive Data Solutions Inc. ( ADS ) products are strictly intended for installation by Certified Technicians who are employed by a registered business specialized in the installation of automotive aftermarket electronics products. Prior to beginning installation of an ADS product in a vehicle, it is the Certified Technician s responsibility to review the most current Product Guide, Install Guide and vehicle-specific notes available in Weblink. ADS is not responsible for any damages whatsoever, including but not limited to any consequential damages, incidental damages, damages for loss of time, loss of earnings, loss of profit, commercial loss, loss of economic opportunity and the like that may or may not have resulted from the use, misuse, improper installation or operation of its products. ADS reserves itself the right to suspend any Weblink account without notice and decline to offer technical support to non-certified Technicians, non-compliant Certified Technicians or end users. BEFORE INSTALLATION - Connect module to computer - Login to Weblink account 3- Flash firmware to module (module is not preloaded with firmware) 4- Use accessories accordingly (accessories are sold separately)
VEHICLE LIST - OF PAGE OF 6 FEATURES MAKE MODEL I NOTE Keyless and smartkey systems will remain functional during remote start. YEAR INSTALL TYPE DATA IMMOBILIZER BYPASS 3X LOCK START/STANDALONE MOD. PUSH TO START CTRL ARM OEM ALARM DISARM OEM ALARM DOOR LOCK DOOR UNLOCK TRUNK/HATCH RELEASE TAILGATE WINDOW RELEASE TACHOMETER OUTPUT BRAKE PEDAL STATUS OUTPUT E-BRAKE OUTPUT DOOR STATUS OUTPUT TRUNK STATUS OUTPUT HOOD STATUS OUTPUT* LEXUS ES350 PTS AT 07-3 TOYOTA Camry PTS AT 07-3 Camry Hybrid PTS AT 07-3 Corolla PTS AT 09-3 Highlander PTS AT 08-3 3 Highlander Hybrid PTS AT 08-3 3 Rav4 PTS AT 09- * Available only if vehicle is equipped with factory hood switch.
BOX CONTENTS - OF PAGE 3 OF 6 DOC.: #56703 084 BOX CONTENTS MODULE 6 PIN WHITE CONNECTOR 4 PIN BLACK CONNECTOR WHITE 3 4 5 6 PROGRAMMING BUTTON LED 7 PIN WHITE CONNECTOR 0 PIN BLACK CONNECTOR WHITE WHITE 3 4 5 6 7 3 A B C F 0 9 8 7 6 5 4 3 BLACK 3 PIN WHITE CONNECTOR DATA CABLE BLUE 3 D E 4 3 BLACK DATA PORT (WEBLINK, RF, TELEMATIC) 3 PIN BLUE CONNECTOR DATA CABLE WEBLINK CABLE (required accessory sold separately) WEBLINK CABLE MODULE DATA PORT COMPUTER USB PORT 4 PIN BLACK CABLE
COMPONENT LOCATOR - OF PAGE 4 OF 6 INTERIOR VIEW A DRIVER SIDE VIEW PASSENGER SIDE VIEW
TYPE - WIRE CHART - OF PAGE 5 OF 6 MAKE MODEL YEAR WIRE DESCRIPTION CONNECTOR NAME CONNECTOR COLOR CONNECTOR TYPE POSITION WIRE COLOR TOYOTA POLARITY MODULE LOCATION COMPONENT LOCATOR Corolla TMMC PTS AT Corolla NUMMI PTS AT Rav4 PTS AT 09-3 09-3 09- Ignition F ~ 8 pin 4 Yellow (+) ECU ~ STSW E5 ~ 9 pin 4 Black (+) ECU ~ PTS ~ ~ 4 pin 7 White (-) Push button ~ Parking Light E8 White 0 pin 8 Brown (-) Parking light switch ~ CanH OBDII ~ 6 pin 6 LtGreen (DATA) OBDII ~ CanL OBDII ~ 6 pin 4 White (DATA) OBDII ~ Ignition F ~ 8 pin 4 Red (+) ECU ~ STSW E5 ~ 9 pin 4 White (+) ECU ~ PTS ~ ~ 4 pin 7 White (-) Push button ~ Parking Light E8 White 0 pin 8 Brown (-) Parking light switch ~ CanH OBDII ~ 6 pin 6 LtGreen (DATA) OBDII ~ CanL OBDII ~ 6 pin 4 White (DATA) OBDII ~ Ignition F ~ 8 pin 4 Yellow (+) ECU ~ STSW E7 ~ 9 pin 4 Red (+) ECU ~ PTS ~ ~ 4 pin 7 White (-) Push button ~ Parking Light E White 0 pin 8 Brown (-) Parking light switch ~ CanH OBDII ~ 6 pin 6 Black (DATA) OBDII ~ CanL OBDII ~ 6 pin 4 White (DATA) OBDII ~
TYPE - WIRING DIAGRAM - OF PAGE 6 OF 6 M M M3 M4 M6 M5 DATA CONNECTIONS ARE REQUIRED ONLY IF IDLE MODE IS DESIRED PTS (-) - 07 8 9 0 3 4 3 4 5 6 7 PTS SWITCH M 0 GRAY/YELLOW (NC) 0 GRAY/RED (NC) 03 GREEN/YELLOW (NC) 04 GREEN/RED (NC) 05 BLUE/YELLOW - PTS (-) OUTPUT 06 BLUE/RED - GROUND (-) INPUT CANL - 4 3 4 5 6 7 8 OBDII CONNECTOR M 0 PINK - IGNITION (+) INPUT 0 PINK/BLACK (NC) 03 ORANGE (NC) 04 ORANGE/WHITE (NC) 05 ORANGE/BLACK - GROUND (-) INPUT 06 BROWN/YELLOW - CANL 07 BROWN/RED - CANH M3 0 YELLOW (NC) 0 YELLOW/RED (NC) 03 YELLOW/BLACK (NC) CANH - 06 IGNITION (+) - 04 A 9 3 8 7 6 5 4 0 3 4 5 6 MAIN BODY ECU FRONT SIDE M4 0 WHITE - IGNITION (+) INPUT 0 WHITE/RED (NC) 03 WHITE/BLACK - STSW (+) OUTPUT A M5 0 BLUE/WHITE (NC) 0 WHITE (NC) 03 BLACK - GROUND 04 RED - V (+) WITHOUT A COMPATIBLE ACCESSORY OR 7.5A V (+) B BACK SIDE M5 DATA CABLE COMPATIBLE ACCESSORY WITH A COMPATIBLE ACCESSORY. IMPORTANT: SEE THE COMPATIBLE ACCESSORIES PAGE FOR DETAILS. STSW (+) - 04 5 6 7 8 9 8 9 0 3 4 3 4 5 6 7 B M6 0 GREEN/BLACK - HOOD STATUS (-) INPUT 0 BLUE/BLACK (NC) 03 RED/WHITE (NC) 04 BROWN (NC) 05 PURPLE/YELLOW (NC) 06 PURPLE/BLACK (NC) 07 WHITE (NC) 08 BLACK/WHITE (NC) 09 GREEN - PARKING LIGHT (-) OUTPUT 0 PURPLE/WHITE (NC) HOOD STATUS (-) WITHOUT OEM HOOD STATUS ONLY WHITE PARKING LIGHT SWITCH PARKING LIGHT (-) - 8 0 9 8 7 6 5 4 3 0 9 8 7 6 5 4 3 IMPORTANT: - NO TAKEOVER AVAILABLE. UPON OPENING VEHICLE DOOR ENGINE WILL SHUTDOWN. - ALL DOORS MUST BE CLOSED TO REMOTE START VEHICLE.
TYPE 3 - WIRE CHART - OF PAGE 7 OF 6 MAKE MODEL YEAR WIRE DESCRIPTION CONNECTOR NAME CONNECTOR COLOR CONNECTOR TYPE POSITION WIRE COLOR POLARITY MODULE LOCATION LEXUS COMPONENT LOCATOR Ignition I ~ 0 pin 07 Black (+) ECU ~ TOYOTA ES350 PTS AT Camry PTS AT Camry Hybrid PTS AT Highlander PTS AT Highlander Hybrid PTS AT 07-07- 07-08-3 08-3 STSW E6 ~ 0 pin 04 Red (+) ECU ~ PTS ~ ~ 4 pin 07 Blue (-) Push button ~ Parking Light E7 White 0 pin 8 Black (-) Parking light switch ~ CanH OBDII ~ 6 pin 06 LtGreen (DATA) OBDII ~ CanL OBDII ~ 6 pin 4 Pink (DATA) OBDII ~ Ignition I ~ 0 pin 07 Brown (+) ECU ~ STSW E9 ~ 0 pin 04 Gray (+) ECU ~ PTS ~ ~ 4 pin 07 Blue (-) Push button ~ Parking Light E White 0 pin 8 Black (-) Parking light switch ~ CanH OBDII ~ 6 pin 06 Black (DATA) OBDII ~ CanL OBDII ~ 6 pin 4 White (DATA) OBDII ~ Ignition I ~ 0 pin 07 Brown (+) ECU ~ STSW E9 ~ 0 pin 04 Gray (+) ECU ~ PTS ~ ~ 4 pin 07 Blue (-) Push button ~ Parking Light E White 0 pin 8 Black (-) Parking light switch ~ CanH ~ ~ 6 pin 06 Black (DATA) OBDII ~ CanL ~ ~ 6 pin 4 White (DATA) OBDII ~ Ignition I ~ 0 pin 07 White (+) ECU ~ STSW D0 ~ 0 pin 04 Pink (+) ECU ~ PTS ~ ~ 4 pin 07 Pink (-) Push button ~ Parking Light D3 White 0 pin 8 LtBlue (-) Parking light switch ~ CanH OBDII ~ 6 pin 06 Blue (DATA) OBDII ~ CanL OBDII ~ 6 pin 4 White (DATA) OBDII ~ Ignition I ~ 0 pin 07 White (+) ECU ~ STSW D0 ~ 0 pin 04 Yellow (+) ECU ~ PTS ~ ~ 4 pin 07 Pink (-) Push button ~ Parking Light D3 White 0 pin 8 LtBlue (-) Parking light switch ~ CanH OBDII ~ 6 pin 06 Black (DATA) OBDII ~ CanL OBDII ~ 6 pin 4 White (DATA) OBDII ~
TYPE 3 - WIRING DIAGRAM - OF PAGE 8 OF 6 M M M3 M4 M6 M5 DATA CONNECTIONS ARE REQUIRED ONLY IF IDLE MODE IS DESIRED PTS (-) - 07 8 9 0 3 4 3 4 5 6 7 PTS SWITCH M 0 GRAY/YELLOW (NC) 0 GRAY/RED (NC) 03 GREEN/YELLOW (NC) 04 GREEN/RED (NC) 05 BLUE/YELLOW - PTS (-) OUTPUT 06 BLUE/RED - GROUND (-) INPUT CANL - 4 3 4 5 6 7 8 OBDII CONNECTOR M 0 PINK - IGNITION (+) INPUT 0 PINK/BLACK (NC) 03 ORANGE (NC) 04 ORANGE/WHITE (NC) 05 ORANGE/BLACK (NC) 06 BROWN/YELLOW - CANL 07 BROWN/RED - CANH M3 0 YELLOW (NC) 0 YELLOW/RED (NC) 03 YELLOW/BLACK (NC) CANH - 06 IGNITION (+) - 07 9 0 3 4 5 6 6 7 8 9 0 3 4 5 BACK SIDE MAIN BODY ECU M4 0 WHITE - IGNITION (+) INPUT 0 WHITE/RED (NC) 03 WHITE/BLACK - STSW (+) OUTPUT M5 0 BLUE/WHITE (NC) 0 WHITE (NC) 03 BLACK - GROUND 04 RED - V (+) WITHOUT A COMPATIBLE ACCESSORY OR STSW (+) - 04 7 8 9 0 3 4 5 6 M5 DATA CABLE COMPATIBLE ACCESSORY WITH A COMPATIBLE ACCESSORY. IMPORTANT: SEE THE COMPATIBLE ACCESSORIES PAGE FOR DETAILS. 7.5A V (+) PARKING LIGHT SWITCH M6 0 GREEN/BLACK (NC) 0 BLUE/BLACK (NC) 03 RED/WHITE (NC) 04 BROWN (NC) 05 PURPLE/YELLOW (NC) 06 PURPLE/BLACK (NC) 07 WHITE (NC) 08 BLACK/WHITE (NC) 09 GREEN - PARKING LIGHT (-) OUTPUT 0 PURPLE/WHITE (NC) PARKING LIGHT (-) - 8 WHITE 0 9 8 7 6 5 4 3 0 9 8 7 6 5 4 3 IMPORTANT: - NO TAKEOVER AVAILABLE. UPON OPENING VEHICLE DOOR ENGINE WILL SHUTDOWN. - ALL DOORS MUST BE CLOSED TO REMOTE START VEHICLE.
MODULE PROGRAMMING PROCEDURE - OF PAGE 9 OF 6 >> Between each step, LED will turn solid RED, this is the default standby mode. 0 STOP ACC ON START Push start button twice [x] to ON position. ENGINE START STOP 0 Wait, LED will turn solid GREEN then will turn OFF. 03 STOP ACC ON START Push start button once [x] to OFF position. ENGINE START STOP 04 Module Programming Procedure completed.
VALET MODE PROGRAMMING PROCEDURE - OF PAGE 0 OF 6 >> NOTE: In Valet Mode, the Remote starter is not functional. Keyless entry, Lock and Unlock will remain functional. See RF kit user manual for alternate valet mode programming. >> To exit valet mode: repeat steps to 5. 0 Time restriction. Complete next step within 7 seconds. 0 OFF ACC ON START Cycle ignition ON five times [5x OFF/ON] rapidly. ENGINE START STOP 03 Wait, LED will turn solid RED for seconds. 04 OFF ACC ON START Set ignition to OFF position. ENGINE START STOP 05 Valet Mode Programming Procedure completed.
PAGE OF 6 MODULE NAVIGATION PROCEDURE - OF >> It is mandatory to exit the Module Navigation at the end of this procedure. Failure to exit the Module Navigation will drain vehicle battery. To exit the Module Navigation at any time: Follow STEP 3. 04 >> Module must be programmed to the vehicle. 05 >> Use the Module Navigation Chart on the next page. 06 Set ignition to OFF position. 07 TO ACCESS THE MENUS: Press and hold programming button until LED turns solid GREEN. 08 IN THE MENUS: Press the programming button as many times as the menu number indicates. LED will flash GREEN an equal amount of times continuously. 09 0 OFF ACC ON START DOC.: #56703 084 TO ACCESS THE OPTIONS: Press and hold programming button until LED turns solid RED. 0 IN THE OPTIONS: Press the programming button as many times as the option number indicates. LED will flash RED an equal amount of times continuously. TO ACCESS THE SETTINGS: Press and hold programming button until LED turns solid GREEN. Configure every other setting and proceed to step 3. [Z] LED will flash GREEN as many times as the current (or default) setting number, continuously. 3 MANDATORY: EXIT MODULE NAVIGATION. Press and hold programming button for 7 seconds. LED will flash RED rapidly. Release programming button. LED will turn OFF. [Z] IN THE SETTINGS: Press the programming button as many times as necessary to access your setting. LED will flash GREEN an equal amount of times continuously. 4 Module navigation completed. To return to the MENUS: exit the Module Navigation and redo the Module Navigation Procedure. >> Failure to exit the Module Navigation will drain vehicle battery. [Y] To save and return to the OPTIONS: Press and hold programming button until LED turns solid RED. [Y] LED will flash RED as many times as the current option number continuously. ENGINE START STOP 0 03 [X]
MODULE NAVIGATION CHART - OF PAGE OF 6 MODULE NAVIGATION CHART: NOTES [X] MENUS [Y] OPTIONS [Z] SETTINGS I II Default settings are listed in bold. Make sure the option is covered on the vehicle before attempting to change the setting. *Vehicle will shutdown when a door is opened. 0 DISARM/UNLOCK BEFORE START 0 OFF 0 ON 0 RELOCK AFTER START 0 OFF 0 ON 03 RELOCK AFTER SHUTDOWN 0 OFF 0 ON 04 FORCE UNLOCK ALL ON FIRST PRESS 0 OFF 0 ON 05 N/A 0 N/A 06 N/A 0 N/A 0 DISABLE 07 FACTORY KEYLESS RS SEQUENCE 0 N/A 03 LOCK + UNLOCK + LOCK 04 LOCK + LOCK + LOCK 0 03 MIN 0 CONFIGURATION 0 05 MIN 03 0 MIN 08 MODULE RUN TIME 04 5 MIN 05 5 MIN 06 30 MIN 07 35 MIN 08 5 MIN 0 0 SEC 0 05 SEC 03 08 SEC 09 WAIT TO START DELAY 04 0 SEC 05 5 SEC 06 0 SEC 07 5 SEC 08 30 SEC 0- N/A 0 N/A 0-07 Technical Support only 0 N/A 0 N/A
REMOTE STARTER ERROR CODES - OF PAGE 3 OF 6 REMOTE STARTER ERROR CODES: NOTES [X] NUMBER OF PARKING LIGHT FLASHES DIAGNOSTIC I II WARNING: The following applies only when the parking lights are connected and supported by the system. After a remote starter failure, the parking lights will flash [X] number times to indicate an error code. See table. 03 Foot brake is ON. 04 Hood is open. 05 Engine tach signal is lost. 06 System is in Valet Mode. 07 Vehicle is moving (VSS). 08 Glow plug timeout error.
MODULE DIAGNOSTICS - OF PAGE 4 OF 6 TEST MODULE LED STATUS DIAGNOSTIC I II III DURING PROGRAMMING DURING REMOTE START WITH IGNITION OFF Flashing RED Solid RED Flashing GREEN Solid GREEN then OFF OFF Flashing RED Solid RED Flashing GREEN Solid GREEN then OFF OFF Flashing RED Solid RED Flashing GREEN Solid GREEN then OFF OFF Missing/wrong information from firmware or vehicle. Module waiting for more vehicle information. Additional steps required to complete module programming. Module correctly programmed. No activity or module already programmed. Module incorrectly programmed. Module incorrectly programmed. Module correctly programmed and operational. Reset in progress. Invalid ground when running status from remote starter. Module incorrectly programmed or connected. Module not programmed. Waiting for more vehicle information. False ground when running status from remote starter. Reset in progress. Module at rest and ready for a remote start sequence.
MODULE RESET PROCEDURE - OF PAGE 5 OF 6 0 Disconnect all connectors from module except the BLACK 4-PIN connector. 07 Reconnect all connectors. 0 Disconnect the BLACK 4-PIN connector. 08 Repeat programming procedure. 03 PRESS AND HOLD programming button while connecting the BLACK 4-PIN connector. >> Failure to follow procedure may result with a DTC or a CHECK ENGINE error message. 04 Wait, LED will flash RED. RELEASE programming button. 05 LED will turn RED for seconds. 06 Module RESET completed.
INSTALLATION CHECKLIST - OF PAGE 6 OF 6 CHECKLIST WARNING: Vehicle engine will start many times. Test in a well ventilated area. Close all vehicle doors, hood and trunk. 3 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Question : Does the vehicle remote start? YES: Go to next step. NO: The module doesn't detect OEM remote lock button from the vehicle communication network. Check all connections, repeat the test and call technical support, if the problem persists. 4 Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down vehicle. Question : Does the vehicle shut down? YES: Go to next step. NO: Repeat step. If the problem persists, press on the brake pedal once [x] to shut down the vehicle and call technical support. 5 RAP Shutdown test Question 3: Did the radio, interior controls, and headlights turn off within 60 seconds after remote start shutdown? YES: Go to next step. NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support, if the problem persists. 6 Open hood. 7 If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step. 8 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Question 4: Does the vehicle remote start? YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test. NO: Go to next step. 9 Close hood. 0 Enter vehicle and close the doors. Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Wait for the vehicle to start. 3 Press brake pedal. Question 5: Does the vehicle shut down? YES: Go to next step. NO: The module does NOT detect the brake pedal signal. Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down, check the brake connection as illustrated in the wiring diagram, if applicable, and call technical support. 4 Exit vehicle. 5 Installation checklist completed.