5- GROUP 5 CONTENTS FRONT BUMPER SSEMBLY 5- SPECIL TOOL 5- FRONT BUMPER SSEMBLY 5- REMOVL ND INSTLLTION 5- DISSSEMBLY ND SSEMBLY 5-5 RER BUMPER SSEMBLY 5-7 SPECIL TOOL 5-7 RER BUMPER SSEMBLY 5-7 REMOVL ND INSTLLTION 5-7 DISSSEMBLY ND RESSEMBLY 5-9 GRNISHES ND MOLDINGS 5-0 SPECIL TOOLS 5-0 GRNISHES ND MOLDINGS 5- REMOVL ND INSTLLTION 5- ERO PRTS 5-5 REMOVL ND INSTLLTION 5-5 WINDSHIELD WIPER ND WSHER* 5-6 GENERL INFORMTION 5-6 WINDSHIELD WIPER ND WSHER DIGNOSIS 5-6 WINDSHIELD WIPER ND WSHER 5-7 REMOVL ND INSTLLTION 5-7 INSPECTION 5-0 Continued on next page WRNINGS REGRDING SERVICING OF SUPPLEMENTL RESTRINT SYSTEM (SRS) EQUIPPED VEHICLES WRNING Improper service or maintenance of any component of the SRS, or any SRS-related component, can lead to personal injury or death to service personnel (from inadvertent firing of the air bag) or to the driver and passenger (from rendering the SRS inoperative) Service or maintenance of any SRS component or SRS-related component must be performed only at an authorized MITSUBISHI dealer MITSUBISHI dealer personnel must thoroughly review this manual, and especially its GROUP 5B - Supplemental Restraint System (SRS) before beginning any service or maintenance of any component of the SRS or any SRSrelated component NOTE The SRS includes the following components: SRS air bag control unit, SRS warning light, front impact sensors, air bag module, clock spring, and interconnecting wiring Other SRS-related components (that may have to be removed/installed in connection with SRS service or maintenance) are indicated in the table of contents by an asterisk (*)
5- RER WIPER ND WSHER 5- GENERL INFORMTION 5- DIGNOSIS 5- RER WIPER 5- REMOVL ND INSTLLTION 5- INSPECTION 5- MRK 5-5 SPECIL TOOL 5-5 MRK 5-5 REMOVL ND INSTLLTION 5-5 DOOR MIRROR 5-7 SPECIL TOOL 5-7 DOOR MIRROR 5-8 REMOVL ND INSTLLTION 5-8 INSPECTION 5-9 SPECIFICTIONS 5-0 FSTENER TIGHTENING SPECIFICTIONS 5-0 SERVICE SPECIFICTIONS 5-0 SELNT ND DHESIVE 5-0
FRONT SPECIL TOOL TOOL 5- FRONT BUMPER SSEMBLY BUMPER SSEMBLY TOOL NUMBER ND NME Ornament remover SUPERSESSION General service tool PPLICTION Removal of clip M50006005
5- FRONT BUMPER SSEMBLY REMOVL ND INSTLLTION FRONT BUMPER SSEMBLY M5000087 5 C D D C E F F B 069 ± 009 N m 5 ± 08 in-lb B E SECTION SECTION B B SECTION C C 6 5 PIN CLW SECTION F F SECTION D D 5 SECTION E E PIN PIN REMOVL STEPS FRONT TURN SIGNL LIGHT UNDER COVER SPLSH SHIELD REMOVL STEPS (Continued) <<>> FRONT BUMPER SSEMBLY 5 IR GUIDE DUCT Required Special Tool: : Ornament Remover C0670 B
5-5 FRONT BUMPER SSEMBLY REMOVL SERVICE POINT <<>> FRONT BUMPER SSEMBLY REMOVL Use special tool to pull up the center pin in the clip Remove the clip PIN CX000B DISSSEMBLY ND SSEMBLY 6 0 M5006008 7 09 ± 0 N m 8 ± in-lb N 8 DISSSEMBLY STEPS RUBBER NUT LICENCE PLTE GRNISH FRONT BUMPER FCE COVER FRONT BUMPER LOWER PLTE 5 FOG LIGHT HOLE COVER 6 FRONT BUMPER CENTER PLTE 7 FRONT BUMPER SIDE PLTE 8 FRONT BUMPER CORNER PLTE C065 B DISSSEMBLY STEPS (Continued) 9 FRONT BUMPER REINFORCEMENT 0 FRONT BUMPER CORE <<>> FRONT BUMPER FCE Required Special Tool: : Ornament Remover
5-6 ND CLW POSITION FRONT BUMPER SSEMBLY FRONT VIEW D D 9 SIDE VIEW F F E E B C B NOTE : POSITION : CLW POSITION C SECTION SECTION B B SECTION C C 9 PIN 7 9 9 SECTION D D 9 5 SECTION E E 9 SECTION F F CLW 9 6 PIN C06680 B DISSSEMBLY SERVICE POINT <<>> FRONT BUMPER FCE REMOVL Use special tool to pull up the center pin in the clip Remove the clip PIN CX000B
SPECIL TOOL TOOL 5-7 RER BUMPER SSEMBLY RER BUMPER SSEMBLY TOOL NUMBER ND NME Ornament remover SUPERSESSION General service tool PPLICTION Removal of clip M500060055 RER BUMPER SSEMBLY REMOVL ND INSTLLTION M500900085 Pre-removal and Post-installation Operation Rear End Trim and Trunk Compartment Trim <ESE SPYDER> Removal and Installation (Refer to GROUP 5, Trims P5-9) Main Muffler Removal and Installation (Refer to GROUP 5, Exhaust Pipe and Main Muffler <L> P5-) Main Muffler Removal and Installation (Refer to GROUP 5, Exhaust Pipe and Main Muffler <0L> P5-) B B C C SECTION SECTION B B SECTION C C PIN PIN C0086 B
5-8 RER BUMPER SSEMBLY REMOVL STEPS BCKUP LIGHT SSEMBLY SPLSH SHIELD <<>> RER BUMPER SSEMBLY Required Special Tool: : Ornament Remover REMOVL SERVICE POINT <<>> RER BUMPER SSEMBLY REMOVL Use special tool to pull up the center pin in the clip Remove the clip PIN CX000B
DISSSEMBLY ND RESSEMBLY 5-9 RER BUMPER SSEMBLY M5000008 8 7 B B C D C D 6 5 SECTION 8 SECTION B B PIN 8 SECTION C C 8 SECTION D D 5 8 PIN 6 DISSSEMBLY STEPS RER BUMPER REINFORCEMENT RER BUMPER CORE LICENSE PLTE LIGHT BRCKET LICENSE PLTE LIGHT SSEMBLY 5 RER BUMPER LOWER PLTE 6 RER BUMPER SIDE PLTE Required Special Tool: : Ornament Remover C0087B 7 RER BUMPER UPPER PLTE <<>> 8 RER BUMPER FCE
5-0 GRNISHES ND MOLDINGS DISSSEMBLY SERVICE POINT <<>> RER BUMPER FCE REMOVL Use special tool to pull up the center pin in the clip Remove the clip PIN CX000B SPECIL TOOLS TOOL GRNISHES ND MOLDINGS TOOL NUMBER ND NME MB9909 Window molding remover SUPERSESSION General service tool PPLICTION Removal of roof drip molding M500060056 MB9909 Ornament remover General service tool Removal of clip
GRNISHES ND MOLDINGS REMOVL ND INSTLLTION <ESE> 5- GRNISHES ND MOLDINGS M50000056 C B B C D D 5 VIEW SECTION SECTION B B SECTION C C SECTION D D VIEW 5 5 DHESIVE TPE: DOUBLE-SIDED TPE [ mm ( 0 in ) WIDTH ND 5 mm ( 0 in ) THICKNESS ] <<>> >>B<< ROOF DRIP MOLDING WINDSHIELD UPPER MOLDING (REFER TO GROUP, WINDSHIELD P-) BELT LINE MOLDING (REFER TO GROUP P-65 ) C0069B RER WINDOW LOWER MOLDING (REFER TO GROUP, LIFTGTE GLSS P-) <<B>> >><< 5 RER PILLR GRNISH
5- GRNISHES ND MOLDINGS Required Special Tools: MB9909: Window Molding Remover : Ornament Remover <ESE SPYDER> 5 C0060 B DRIP GRNISH WINDSHIELD UPPER MOLDING (REFER TO GROUP, WINDSHIELD P-) BELT LINE MOLDING (REFER TO GROUP, DOOR WINDOW GLSS RUNCHNNEL ND DOOR OPENING WETHERSTRIP P- 65) BCK BELT MOLDING 5 QURTER BELT SIDE GRNISH
5- GRNISHES ND MOLDINGS REMOVL SERVICE POINTS <<>> ROOF DRIP MOLDING REMOVL CUTION If the molding has become warped, it should not be reused Use special tool MB9909 to lever out the molding <<B>> RER PILLR GRNISH REMOVL MB9909 C0066B Use a resin spatula to scrape off the double-sided tape Wipe the body surface and clean it with a shop moistened with isopropyl alcohol DOUBLE-SIDE TPE C0067B INSTLLTION SERVICE POINTS >><< RER PILLR GRNISH INSTLLTION Scrape off the double-sided tape with a resin spatula or gasket scraper C000 C0068 Use a shop towel moistened with M D Part number 8906 or equivalent to wipe the protect molding surface CUTION Do not remove all of the residual adhesive Remove only a small portion of the residual adhesive CUTION lways apply it evenly on the entire surface, because a lot or little will reduce its strength Do not touch the painted surface ffix the specified double-sided tape [ mm (0 inch) wide and 5 mm (0 inch) thick]
5- GRNISHES ND MOLDINGS DHESIVE TPE BCKING PPER C000B FRONT PILLR OUTER RER PILLR GRNISH INSTLLTION Tear off the double-sided tape backing paper NOTE: If you attach the adhesive tape to the edge of the backing paper, if will be easy to tear off Install the rear pillar garnish NOTE: If the double-sided tape is difficult to affix in cold temperature, etc, warm the bonding surfaces of the body and rear pillar garnish to about 0 60 C (0 0 F) before affixing the tape Firmly press in the rear pillar garnish >>B<< ROOF DRIP MOLDING INSTLLTION fter installing the clip to the outer front pillar in alignment with its section, cut from section B SECTION B SECTION C0069B
REMOVL ND INSTLLTION 5-5 ERO PRTS ERO PRTS M500500009 B B SECTION SECTION B B REMOVL STEPS STONE GURD <VEHICLES WITHOUT SIDE IR DM> FRONT SIDE IR DM RER SIDE IR DM RER SPOILER C006B
5-6 WINDSHIELD WIPER ND WSHER WINDSHIELD WIPER ND WSHER GENERL INFORMTION OPERTION Windshield Low-speed (and High-speed) Wiper Operation If the wiper switch is turned to the "LO" position with the ignition switch at the "CC" or "ON" position, the column switch sends a low-speed wiper ON and high-speed wiper OFF signals to the front-ecu This turns the wiper signal on and the wiper speed switching relay off (low-speed), causing the wipers to operate at low-speed If the wiper switch is turned to the "HI" position, the column switch sends a low-speed wiper OFF and high-speed wiper ON signals to the front- ECU This turns both the wiper signal and the wiper speed switching relay on (high-speed), causing the wipers to operate at high-speed Windshield Intermittent Wiper Operation The ETCS-ECU calculates the wiper operation interval according to the voltage signal sent from the column switch Then the ETCS-ECU sends a signal to the front-ecu The front-ecu determines the wiper operation interval and turns on the wiper relay signal This causes the wiper auto stop relay to turn on Then the wiper auto stop relay will turn off after the wipers reach the park position This causes the wiper signal relay and then the wipers to turn off If the wiper signal relay remains off for the wiper operation interval, the relay turns on again, causing the wipers to operate in intermittent mode WINDSHIELD WIPER ND WSHER DIGNOSIS The windshield wiper and washer are controlled by ETCS-ECU For troubleshooting, refer to GROUP 5B, SWS Diagnosis P5B-7 M5000006 Windshield Mist Wiper Operation If the wiper switch is turned to the "MIST" position with the ignition switch at "CC" or "ON" position, the mist wiper high-speed operation signal is sent to the front-ecu This signal turns on the wiper speed switching relay, causing the wipers to work at high-speed while the mist switch is on While the mist wiper switch remains turned on when the intermittent mode is still working, the wipers work as the mist wiper However, the wipers return to the intermittent mode again when the wiper auto stop signal turns on after the mist wiper switch is turned off Windshield Washer Operation If the wiper switch is turned to the "WSHER" position with the ignition switch at "CC" or "ON" position, the washer ON signal is sent to the front-ecu, causing the wiper signal to turn on after 06 seconds fter the washer switch signal turns off, the wiper signal turns off in three seconds If the wiper switch is turned the "WSHER" position while the wiper is at intermittent mode, the washer works for that period when the washer switch remains on Then the wipers return to the intermittent mode M5000700099
WINDSHIELD WIPER ND WSHER REMOVL ND INSTLLTION 5-7 WINDSHIELD WIPER ND WSHER M5007600 BTTERY ± N m ± 6 in-lb 7 ± N m ± 6 in-lb 50 ± 07 N m ± 6 in-lb VIEW 5 50 ± 07 N m ± 6 in-lb 9 0 VIEW ± N m 00 ± in-lb 8 SECTION CLW NOTE : POSITION : CLW POSITION FRONT-ECU ETCS-ECU WIPER MOTOR ND LINK SSEMBLY REMOVL STEPS >>B<< WIPER RM ND BLDE SSEMBLY FRONT DECK GRNISH <<>> >><< 5 WIPER MOTOR ND LINK SSEMBLY WSHER NOZZLE REMOVL STEPS FRONT SPLSH SHIELD 6 WSHER HOSE 7 WSHER NOZZLE WSHER TNK REMOVL STEPS FRONT SPLSH SHIELD (REFER TO GROUP, FENDER P-9) FRONT BUMPER SSEMBLY (REFER TO GROUP 5P5- ) C006 B WSHER TNK REMOVL STEPS PSSENGER'S SIDE HEDLIGHT (REFER TO GROUP 5 P5- ) WSHER FLUID DRINING ND REFILLING 6 WSHER HOSE 8 WSHER TNK SSEMBLY 9 FRONT WINDSHIELD WSHER MOTOR 0 RER WINDSHIELD WSHER MOTOR NOTE: For removal and installation of the wiper and washer switch, refer to GROUP 5 P5-, Column Switch
5-8 WINDSHIELD WIPER ND WSHER REMOVL SERVICE POINT WIPER MOTOR ND LINK SSEMBLY <<>> WIPER MOTOR ND LINK SSEMBLY REMOVL Remove the five mounting bolts of the wiper motor and link assembly and disconnect the connector To protect the windshield, apply duct tape to the entire circumference of the glass near the wiper motor and link assembly installation position CUTION Be careful not to damage the windshield glass when removing the wiper motor and link assembly Use a flat-tipped screwdriver to disengage the driver's side link from the center crank arm Remove the wiper motor and link assembly from the vehicle body (the cowl) while being careful not to scratch the windshield glass DRIVER'S SIDE LINK CENTER CRNK RM FLT-TIPPED SCREWDRIVER X0607W C00696B INSTLLTION SERVICE POINTS DRIVER'S SIDE LINK CENTER CRNK RM FLT-TIPPED SCREWDRIVER BX0607W C00697B >><< WIPER MOTOR ND LINK SSEMBLY INSTLL- TION Disengage the driver's side link from the center crank arm when replacing with new one CUTION Be careful not to scratch the windshield glass when installing the wiper motor and link assembly Install the wiper motor and link assembly to the vehicle body (the cowl) while being careful not to scratch the windshield glass
5-9 WINDSHIELD WIPER ND WSHER WTER PUMP PLIERS DRIVER'S SIDE LINK Use water pump pliers to engage securely the driver's side link with the center crank arm CENTER CRNK RM X0708W C00698B BOLT INSTLLTION ORDER 5 WIPER MOTOR ND LINK SSEMBLY Install the five mounting bolts in the shown order to install the wiper motor and link assembly 5 Secure the wiper motor and link assembly in the wiper park position (Refer to, Wiper Motor Check P5-0) X0608W C00699B PSSENGER'S SIDE DRIVER'S SIDE >>B<< WIPER RM ND BLDE SSEMBLY INSTLLTION Install the wiper blade at the specified position (standard value) Standard value: Driver's side: mm ( 7 inches) Passenger's side: 8 8 mm (5 9 inches) FRONT DECK GRNISH END C0007C
5-0 WINDSHIELD WIPER ND WSHER INSPECTION FRONT WIPER MOTOR CHECK M509009 Check the wiper motor after disconnecting the wiring harness connector, and with the wiper motor remaining installed to the body 5 INSPECTION WHILE OPERTING 5 5 LOW-SPEED HIGH- SPEED INSPECTION WHILE STOPPED Wiper Motor at Low-Speed and High-Speed Operation Connect the battery to the wiper motor as shown in the illustration, and then check the operation of the wiper motor at low speed and at high speed Wiper Motor at Stop Position Operation Run the wiper motor at low-speed, disconnect the battery, and stop the motor Reconnect the battery as shown in the illustration, and confirm that the motor starts turning at low-speed, and then stops at the automatic stop position 5 5 LOW-SPEED UTO STOP C00700B FRONT WSHER MOTOR CHECK With the washer motor installed to the washer tank, fill the washer tank with water Check that water is sprayed out strongly when battery voltage is applied to terminal () and terminal () is grounded C0070 0 98765 UPPER SIDE C0007C WINDSHIELD WIPER ND WINDSHIELD WSHER SWITCH CHECK Windshield wiper and washer switch SWITCH POSITION TESTER CONNECTION OFF,, 0,, Windshield mist wiper switch Windshield intermittent wiper switch SPECIFIED CONDITION Open circuit Less than ohm Less than ohm
5- RER WIPER ND WSHER SWITCH POSITION Windshield low-speed wiper switch Windshield high-speed wiper switch Windshield washer switch TESTER CONNECTION SPECIFIED CONDITION 0 Less than ohm Less than ohm Less than ohm Windshield intermittent wiper interval adjusting knob Measure the resistance value at terminal numbers 7 and 8 The resistance value should rise smoothly from approximately 0 Ω ("FST" position) to approximately kω ("SLOW" position) RER WIPER ND WSHER GENERL INFORMTION OPERTION Rear Wiper Operation If the rear wiper and washer switch is turned to the "INT" position with the ignition switch at "CC" or "ON" position, the ETCS-ECU causes the rear wiper to operate continuously two times, then intermittently at eight-second intervals If the selector lever is moved to the "R" position when the rear wiper and washer switch is turned the "INT" position and the ignition switch at "CC" or "ON" position, park/neutral position switch "R" turns ON One second later, the ETCS-ECU causes the rear wiper to operate two times continuously to ensure good rearward visibility The ETCS-ECU then causes the rear wiper to again operate intermittently at eight-second intervals DIGNOSIS The rear wiper and washer are controlled by ETCS- ECU For troubleshooting, refer to GROUP 5B, SWS Diagnosis P5B-7 M5000008 Rear Washer Operation If the rear wiper and washer switch is turned the "WSHER" position with the ignition switch at "CC" or "ON" position, the rear washer ON signal is sent to the ETCS-ECU, causing the rear wiper signal to turn on after 09 seconds fter the rear washer switch signal turns off, the rear wiper signal turns off in three seconds If the rear wiper and washer switch is turned to the "WSHER" position while the rear wiper is at intermittent mode, the rear washer works for that period when the washer switch remains on Then the rear wipers return to the intermittent mode M50007008
5- RER WIPER REMOVL ND INSTLLTION RER WIPER ND WSHER M500880005 6 5 98 ± 0 N m 87 ± 7 in-lb 9 ±07 N m ± 6 in-lb X075W C007B WSHER TNK SSEMBLY ND RER WSHER MOTOR (REFER TO GROUP 5, WINDSHIELD WIPER ND WSHER P5-7) RER WIPER MOTOR SSEMBLY REMOVL STEPS COVER >><< RER WIPER RM ND BLDE SSEMBLY LIFTGTE LOWER TRIM (REFER TO GROUP, LIFTGTE TRIM P-7) >>B<< GROMMET RER WIPER MOTOR SSEMBLY RER WSHER HOSE REMOVL STEPS QURTER TRIM, LOWER <RH> (REFER TO GROUP 5, TRIMS P5-9) 5 RER WSHER HOSE >><< 6 WSHER NOZZLE NOTE: For removal and installation of the wiper and washer switch, refer to GROUP 5, Column SwitchP5-
GLSS CENTER LINE WSHER NOZZLE 5- RER WIPER ND WSHER INSTLLTION SERVICE POINTS >><< WSHER NOZZLE INSTLLTION Install the washer nozzle in the specified direction CERMIC LINE 5 DISCHRGE DIRECTION X0707W C0066B CERMIC LINE GLSS END LINE >>B<< GROMMET INSTLLTION Install the grommet so that the arrow points upwards RROW GROMMET C0067B CERMIC LINE GLSS END LINE >>C<< RER WIPER RM ND BLDE SSEMBLY INSTLLTION Install the wiper blade so that the tip stops at the standard position (standard value), and also so that the lower section of the wiper blade enters the middle of the defogger pattern Standard value (): 89 99 mm (5 ± 9 inches) WIPER RM ND BLDE SSEMBLY C0068B
5- RER WIPER ND WSHER INSPECTION RER WIPER MOTOR CHECK M5090000 Check the wiper motor after first disconnecting the wiring harness connector, and with the wiper motor remaining installed to the body Wiper Motor Operation Connect a battery to the wiper motor as shown in the illustration and inspect the motor operation OPERTION CHECK Wiper Motor at Stop Position Operation Run the wiper motor, disconnect the battery, and stop the motor Reconnect the battery as shown in the illustration, and confirm that after the motor starts turning it stops at the automatic stop position STOP POSITION CHECK C0069B RER WSHER MOTOR CHECK With the washer motor installed to the washer tank, fill the washer tank with water When the battery is connected as shown in the figure, check that the washer squirts out strongly C0060 RER WIPER ND WSHER SWITCH INSPECTION 0 98765 SWITCH POSITION TERMINL CONNECTION SPECIFIED CONDITION UPPER SIDE OFF 5 6, Open circuit 5 9 Rear wiper switch ON 5 6 Less than ohm Rear washer switch ON 5 9 Less than ohm C0007C
SPECIL TOOL TOOL TOOL NUMBER ND NME MB99058 Stripe tape spatula 5-5 MRK MRK SUPERSESSION PPLICTION - Bonding of the mark M5000600575 MB99058 MRK REMOVL ND INSTLLTION M50800067 < ESE > < ESE SPYDER > TOP MRK >><< ENGINE SPECIFICTION MRK >><< GRDE MRK (GT, RS, GS) >><< SPYDER MRK Required Special Tool: MB99058: Stripe Tape Spatula C00660B INSTLLTION SERVICE POINT >><< MRK INSTLLTION PPLICTION LOCTION The distance (from the mark right end to the notch) should be identical to the distance ' (from the front door opening line to the mark right end)
5-6 ENGINE SPECIFICTION MRK LH SIDE MRK GRDE MRK GT (LSO PPLICBLE FOR GS) FRONT DOOR OPENING LINE FRONT FENDER PNEL PRESS LINE ' LIGN THE MRK BOTTOM END WITH THE LIFTGTE BOTTOM END LIGN THE MRK NOTCH WITH THE LIFTGTE RIGHT END NOTE RH SIDE IS SYMMETRICL ON LH SIDE SPYDER MRK TRUNK LID END LINE LIGN THE MRK LINE END WITH THE TRUNK LID LIFT END LIGN THE MRK BOTTOM END WITH THE TRUNK LID BOTTOM END C0066B CUTION Work in a dust-free workplace with temperature of 0 8 C (60-00 F) If workplace temperature is under 0 C (60 F), warm tape and vehicle body (adhesion area) to 0 8 C (60 00 F) Install the tape by the following procedure () Use M D Part number 8906 or equivalent to wipe off oil from stripe tape adhesion area () Remove protective paper from back of stripe tape and adhere entirely to indicated area
5-7 DOOR MIRROR 0-5 CUTION Pressing the mark horizontally may lead to a slack, clinching or improper position If the mark is pressed improperly, the mark may be easily peeled off () Make sure that air bubbles are not trapped in the application surface When applying the mark, use special tool MB99058 to press the mark from its center to top and bottom gradually MB99058 PPLICTION TPE C00058B PPLICTION TPE () Peel off an application tape (top protection paper) horizontally and carefully from one end If an air bubble is left in the mark, open a hole by using a needle, and then use special tool MB99058 to expel the air bubble CORRECT INCORRECT C00059B SPECIL TOOL TOOL TOOL NUMBER ND NME Ornament remover DOOR MIRROR SUPERSESSION General service tool PPLICTION M5000600586 Removal of remote controlled mirror switch
5-8 DOOR MIRROR REMOVL ND INSTLLTION DOOR MIRROR M50060006 8 8 7 5 6 (ELECTRIC) 6 (DIRECT) VIEW NOTE : CLW POSITION VIEW VIEW B, SECTION 6, CLW SECTION B B, 6 B REMOTE CONTROLLED MIRROR SWITCH DOOR MIRROR REMOVL STEPS DOOR TRIM (REFER TO GROUP P-5) DELT COVER, INNER TWEETER COVER PD C008 B DOOR MIRROR REMOVL STEPS 5 TWEETER 6 DELT COVER BSE 7 HRNESS CONNECTOR <VEHICLES WITH REMOTE CONTROLLED MIRROR> 8 DOOR MIRROR SSEMBLY
5-9 DOOR MIRROR INSPECTION ELECTRIC REMOTE CONTROL MIRROR OPERTION CHECK M50900 Check that the mirror moves as described in the table when each terminal is connected to the battery C0068 DIRECTION OPERTION TESTER CONNECTION Up Connect terminal to the negative battery terminal Connect terminal to the positive battery terminal Down Connect terminal to the negative battery terminal Connect terminal to the positive battery terminal Right Connect terminal to the negative battery terminal Connect terminal to the positive battery terminal Left Connect terminal to the negative battery terminal Connect terminal to the positive battery terminal SPECIFIED CONDITION Less than ohm Less than ohm Less than ohm Less than ohm DOOR MIRROR CONTROL SWITCH CHECK SWITCH POSITION TESTER CONNECTION SPECIFIED CONDITION 5 6 7 8 9 Left side Up 8, 6 7 Less than ohm Down 7, 6 8 Less than ohm Right 6, 7 Less than ohm Left, 6 7 Less than ohm C0068 Right side Up, 6 7 Less than ohm Down 6, 7 Less than ohm Right 7, 6 9 Less than ohm Left 9, 6 7 Less than ohm
5-0 SPECIFICTIONS SPECIFICTIONS FSTENER TIGHTENING SPECIFICTIONS M505009 ITEMS SPECIFICTIONS Front bumper Front turn signal light screw 069 ± 009 N m (5 ± 08 in-lb) Front fog light assembly screw 9 ± 07 N m ( ± 6 in-lb) Front fog light bracket bolt 9 ± 07 N m ( ± 6 in-lb) License plate garish screw 09 ± 0 N m (8 ± in-lb) Windshield wiper and washer Wiper arm and blade assembly nut ± N m ( ± 6 in-lb) Wiper motor and wiper link assembly bolt 50 ± 07 N m ( ± 6 in-lb) Washer tank motor assembly bolt ± N m (00 ± in-lb) SERVICE SPECIFICTIONS ITEMS STNDRD VLUE Windshield wiper blade position Driver's side ( 7) installation mm (in) Passenger's side 8 8 (5 9) Rear wiper blade position installation mm (in) 89 99 (5 9) M500000 SELNT ND DHESIVE ITEM Rear pillar garnish M50005006 SPECIFICTIONS dhesive tape: Double-sided tape [ mm (0 in) width and 5 mm (0 in) thick]