REMOTE ENGINE STARTER

2008- LAND CRUISER TVIP V4 REMOTE ENGINE STARTER (RES) TROUBLESHOOTING GUIDE REMOTE ENGINE STARTER TROUBLESHOOTING GUIDE Rev. B 01/18/06

Remote Engine Starter Troubleshooting Guide Page 2 TABLE OF CONTENTS DESCRIPTION PAGE PRE-CHECK 3 RES ECU PIN LAYOUT AND TERMINALS 4-5 ACCESSORY GATEWAY ECU PIN LAYOUT AND TERMINALS 6 HOW TO PROCEED WITH TROUBLESHOOTING 7 CUSTOMER PROBLEM ANALYSIS CHECK 8 PROBLEM SYMPTOMS TABLE 9 DIAGNOSTIC OPERATION 10-11 Diagnosis Mode Reset Conditions 12 DIAGNOSTIC CODE BY SCAN TOOL 12 INSPECTIONS Engine Does Not Start by Remote 13-15 Engine Does Not Stop by Remote 16-17 Engine Stops Unexpectedly 18-19 Failed Registration of Immobilizer ID Code 20-21

Remote Engine Starter Troubleshooting Guide Page 3 PRE-CHECK REMOTE ENGINE STARTER CHARACTERISTICS (a) The operation distance varies according to how customers hold the transmitter or where it is used. (b) Strong external radio waves or other frequency noise may interfere with the Remote Engine Starter s operation distance. REMOTE ENGINE STARTER BASIC FUNCTIONS (a) Stand on the driver s side, three feet away from the vehicle. (b) Turn the transmitter toward the vehicle and press and release the LOCK button twice within two seconds. Immediately press and hold the LOCK button for three seconds. The hazard lights flash after three seconds. (c) The engine then starts, and the hazard lights flash for 20 seconds. (d) Press the UNLOCK button. The engine stops and hazard lights flash twice. OR Press and hold the LOCK button for two or more seconds. The engine stops and the hazard lights flash once.

Remote Engine Starter Troubleshooting Guide Page 4 RES ECU PIN LAYOUT <Connector> Part Number: 90980-12258 Color: White Part Number: 90980-11361 Color: White 10 9 8 7 6 5 4 3 2 1 20 19 18 17 16 15 14 13 12 11 2 8 7 6 5 4 3 1 MALE FRONT VIEW MALE FRONT VIEW Terminal No. Content 1 MPX Signal 2 ST1 Input *1 3 SHIFT P 4 RES Diag 5 OPTIONINPUT2 6 CHECK ENGINE LIGHT 7 OPTIONINPUT3 8 (HOOD SW.) 9 STSW Signal *2 10 OBD2 (Diag.) *1 11 +B 12 IG1 13 N.C. 14 ST1 Output *1 15 N.C. 16 GND 17 GND 18 N.C. 19 N.C. 20 OBD2 (Imm. ECU) *1 Signal MPX ST1I P RDIG OPI2 LDUT OP13 (DSWH) STSW OB2I +B IGI - ST10 - GND GND - - OB20 Terminal No. 1 AM1 *1 2 AM2 *1 3 IGI *1 4 N.C. 5 ACC *1 6 ST2 *1 7 N.C. 8 IG2 *1 Content Signal AM1 AM2 IG1 - ACC ST2 - IG2 *1: Vehicles without Push Start System only. *2: Vehicles with Push Start System only.

Remote Engine Starter Troubleshooting Guide Page 5 RES ECU TERMINALS Remote Engine Starter ECU Input/Output Specifications Signal Symbol I/O Condition +B +B ECU+B 12V (TYP) GND E ECU GND 0 V AM1 *1 AM1 Input Dropping voltage: Less than 0.2V AM2 *1 AM2 Input IG1 *1 IG1 Output IG2 *1 IG2 Output ACC *1 ACC Output ST2 *1 ST2 Output IG1 IG1 Input ON : Over (+B-1) V (same terminal as above) Hood SW DSWH Input Close : Less than 1V Shift position P P Input ON : Over (+B-1) V Check engine LDUT Input OFF : Less than 2.2V lamp Diagnosis communication1 *1 Diagnosis communication2 *1 ON : Over 6V OB2I Input Pulse generation during communication OB2O Output Pulse generation during communication BEAN MPX Commu- Pulse generation communication nication ST1(IN) *1 ST1I Input ON : Over (+B-1)V ST1(OUT) *1 ST1O Output Permissible current : 500mA STSW *2 STSW Output ON : Over (+B-2) V Remote engine starter diagnosis input RDIG Input ON : Less than 1V *1: Vehicles without Push Start System only. *2: Vehicles with Push Start System only.

ACCESSORY GATEWAY ECU PIN LAYOUT Remote Engine Starter Troubleshooting Guide Page 6 <Connector> Part Number: 90980-10798 Color: Dark gray 5 4 3 2 1 MALE FRONT VIEW Terminal No. Content Signal 1 MPX Signal for Accessory MPXY 2 N.C. _ 3 +B +B 4 GND GND 5 MPX Signal for Vehicle MPX ACCESSORY GATEWAY ECU TERMINALS Accessory gateway ECU Input/Output Specifications Signal Symbol I/O Condition +B +B ECU+B 12V (TYP) GND E ECU GND 0 V MPX signal for MPXY Commu- Pulse generation accessory MPX signal for Vehicle LAN MPX nication Communication

HOW TO PROCEED WITH TROUBLESHOOTING HINT Use these procedures to troubleshoot the Remote Engine Starter. The hand-held tester should be used in Step 4. NEXT NEXT NEXT 1 VEHICLE BROUGHT IN FOR SERVICE Remote Engine Starter Troubleshooting Guide Page 7 2 CUSTOMER PROBLEM ANALYSIS CHECK AND SYMPTOM CHECK 3 PROBLEM SYMPTOMS TABLE 4 OVERALL ANALYSIS AND TROUBLESHOOTING (a) Diagnostic Mode check, if necessary (see page 10) (b) Check ECU terminals (see pages 4 to 6) (c) Check wire harness (see I/I and EWD) NEXT NEXT NEXT NEXT END 5 Please fax the Replacement Authorization Request Sheet and Customer Problem Analysis Check Sheet to (800) 438-5410 to receive an RES Authorization Number. For assistance, please call Fujitsu Ten Technical Support at (800) 237-5413. 6 CHECK INSTALLATION AND PROGRAMING, REPAIR OR REPLACE 7 CONFIRMATION TEST

Remote Engine Starter Troubleshooting Guide Page 8 CUSTOMER PROBLEM ANALYSIS CHECK REMOTE ENGINE STARTER SYSTEM Check Sheet Today s date: Customer s Name R.O. No. Problem Conditions Verified Unable to verify Date Problem First Occurred (M) /(D) / (Y) Where did the problem occur? Home Work Other How far from the user was the car? Less than 5 feet 5 to 10 feet 10 to 30 feet More than 30 feet When did the problem occur? After car repaired After engine stalled After other accesorry installed After change to new car key or transmitter How often has the problem occurred? Weather Conditions When Problem Occurred Always Sometimes Once only Weather Clear Cloudy Rainy Snowy Various/Other Outdoor Temperature Hot Warm Cool Very Cold Approx. Deg F Customer Complaint (After completing inspection, please select one from below, or choose other if not applicable.) Engine did not start (1) Was the Immobilizer code registration confirmed? Yes No (2) How many times did the hazard lights flash in Diagnostic Mode? times Engine stopped unexpectedly (1) Was the total run time under 20 minutes? Yes No (2) How many times did the hazard lights flash in Diagnostic Mode? times Engine did not stop (1) What condition was present when the problem occurred? LOCK button pressed and held UNLOCK button pressed Engine ran more than 10 min. Hood was open Key was in ignition or push start button was pressed Check Engine light came on Other Other (Please explain in detail)

Remote Engine Starter Troubleshooting Guide Page 9 PROBLEM SYMPTOMS TABLE Symptom Check item See page Engine does not start by remote. 1. Remote keyless entry operation 2. Engine operation 3. Remote E/G start operation 4. Remote Engine Starter diagnosis 5. Vehicle circuit (Engine Starter ECU input/output check) 6. Immobilizer ID code registration 13 Engine does not stop by remote. Engine stops unexpectedly. Registration of ID code of Immobilizer failed. 1. Remote keyless entry operation 2. Remote E/G stop operation 3. Vehicle circuit (Engine Starter ECU input/output check) 1. Total operation time (Run time) 2. Remote Engine Starter Diagnosis 3. Vehicle circuit (Engine Starter ECU input/output check) 1. Immobilizer ID code registration operation 2. Vehicle circuit (Engine Starter ECU input/output check) 16 18 20

Remote Engine Starter Troubleshooting Guide Page 10 DIAGNOSTIC OPERATION ENGINE STARTER DIAGNOSIS NOTE: Turn the engine off before performing any diagnostic function. The Diagnostic Mode can help determine why the engine stops/fails. To set the Diagnostic Mode, you must locate and connect the Diagnostic Connectors (RDIG). To do so, follow the steps below: (1) Remove the passenger side step cover. Step Cover (2) Remove the passenger side cowl cover. Nut Cowl Cover (3) Find and connect the Diagnostic Connectors (RDIG) with label, located in the passenger cowl area. RES Diagnostic Connectors These connectors must be connected.

Remote Engine Starter Troubleshooting Guide Page 11 Diagnostic Operation Connect the diagnostic connector: < Open GND (Connect) > IG OFF ON Press the Brake pedal: < OFF ON (Press) > Wait for more than 3 seconds Hazard Lights Flashing DIAGNOSTIC FACTOR IDENTIFICATION The Diagnostic Mode indicates the causes of engine stop or failure to start as listed below. Engine Stop Factor Engine Stop Factor Hazard Lights Flashing Time Affected Terminal No abnormal stop in the past 0 None 9 Key switch is on 1 MPXY, MPX 1 Any door is unlocked 2 MPXY, MPX 4 Engine RPM is too high or low 3 MPXY, MPX 7 Check Engine is indicated 4 LDUT 8 Order of Priority*2 Any door or hood is opened 5 MPXY, MPX, 2 (DSWH) Gearshift position is not P 6 MPXY, MPX, P 5 Brake is on 7 MPXY, MPX, 3 Vehicle speed is abnormal 8 MPXY, MPX, 6 Discrepancy on Immobilizer Collation. 9 MPX, OB2I, OB2O 9 *1 Check Engine Connection NG 10 MPX, LDUT 10 *1: The immobilizer registration should be confirmed if the connection and terminal signal don t have any problem. (Only installation timing) *2: When two or more of these conditions are responsible for the engine stop or non-start, they will be indicated by order of priority.

Remote Engine Starter Troubleshooting Guide Page 12 DIAGNOSTIC MODE EXIT CONDITIONS You may exit the Diagnostic Mode by doing either of the following: 1: Disconnect the diagnostic connectors. OR 2: Wait 10 minutes from the time the diagnostic connectors were connected. After completing the repair, the diagnostic connectors should be disconnected and re-secured prior to reassembly of the trim covers. NOTE: The Remote Engine Starter will store the code for the last engine stop factor in its memory, even after exiting Diagnostic Mode. The code cannot be cleared from the Remote Engine Starter ECU s memory. DIAGNOSTIC CODE BY SCAN TOOL When RES has the following defects, diagnostic code is indicated by the scan tool. 1: Internal Relay of the RES ECU Abnormality Detected CODE [B2334] 2: Internal Switch of the RES ECU for Vehicle Starter Abnormality Detected CODE [B2333] If you find the above code by the scan tool, PLEASE CALL Fujitsu Ten Technical Support at (800) 237-5413.

Remote Engine Starter Troubleshooting Guide Page 13 INSPECTION 1/9 ENGINE DOES NOT START BY REMOTE. INSPECTION PROCEDURE (a) Ignition must be OFF when starting this procedure. 1 CHECK REMOTE KEYLESS ENTRY OPERATION (a) Press the LOCK button. (b) Confirm the doors are locked. OK 2 CHECK ENGINE OPERATION <Smart Entry Vehicle> (a) Start the engine with the POWER button. (b) Confirm the engine is activated. NO GO TO VEHICLE S REPAIR MANUAL AND CHECK REMOTE KEYLESS ENTRY OPERATION <Non Smart Entry Vehicle> (a) Start the engine with the key in the IG key cylinder. (b) Confirm the engine is activated. OK NO 3 CHECK REMOTE ENGINE START OPERATION (a) Press and release the LOCK button twice within 2 seconds. Then immediately press and hold the LOCK button for 3 seconds. GO TO VEHICLE S REPAIR MANUAL AND CHECK ENGINE OPERATION OK END NO HINT: EXPLAIN THE FOLLOWING INFORMATION TO CUSTOMER: The transmission range for remote start may be shorter than the remote s basic keyless entry operation. Range can also be affected by the surrounding environment. GO TO STEP 4

Remote Engine Starter Troubleshooting Guide Page 14 INSPECTION 2/9 4 CHECK REMOTE ENGINE STARTER DIAGNOSIS (a) Please check the diagnostic code by scan tool. (See Diagnostic Code by Scan Tool on page 12). If [B2334] or [B2333] is indicated, please call Fujitsu Ten Technical Support at (800) 237-5413. (b) Connect the diagnostic connectors to enter the Diagnostic Mode. (See Diagnostic Operation on page 10 for the location of the connectors). If the connectors are already plugged in, please disconnect and plug them in again. (c) Check the factor to stop the engine by applying the brake in Diagnostic Mode. Hazard lights will flash in accordance with the factor of engine stop. (See Diagnostic Factor Identification on page 11.) Number of hazard light flashes: 1 to 10 5-1 CHECK VEHICLE CIRCUIT (REMOTE ENGINE STARTER ECU AND ACCESSORY GATEWAY ECU INPUT/OUTPUT CHECK) Measure the voltage and resistance of the affected terminals (listed on page 11) on the wire harness for Remote Engine Starter ECU and Accessory Gateway ECU. Then, compare measured value to specifications. (See RES ECU and Accessory Gateway ECU pin layout and terminal information from pages 4 to 6 for specifications.) OK Number of hazard light flashes: 0 NO GO TO STEP 5-3 GO TO STEP 5-2 5-2 CHECK VEHICLE CIRCUIT (REMOTE ENGINE STARTER ECU AND ACCESSORY GATEWAY ECU INPUT/OUTPUT CHECK) Measure the voltage and resistance of the other or all terminals on the wire harness for Remote Engine Starter ECU and Accessory gateway ECU. Then, compare measured value to specifications. (See RES ECU and Accessory Gateway ECU pin layout and terminal information from pages 4 to 6 for specifications.) OK GO TO STEP 6 NO GO TO STEP 5-3 5-3 CHECK VEHICLE CIRCUIT (WIRE HARNESS CONTINUITY CHECK) Check for continuity of the wire harness. (See Installation Instruction and Electrical Wiring Diagram.) OK NO PLEASE VERIFY THE WIRE HARNESS CONNECTIONS If they are OK: CHANGE REMOTE ENGINE STARTER ECU AND ACCESSORY GATEWAY ECU CHANGE REMOTE ENGINE STARTER WIRE HARNESS

Remote Engine Starter Troubleshooting Guide Page 15 INSPECTION 3/9 6 RETRY REGISTRATION OF IMMOBILIZER ID CODE See Remote Engine Starter installation instructions posted on TIS for the registration method. OK 7 RETRY REMOTE ENGINE START NO CHANGE REMOTE ENGINE STARTER ECU AND ACCESSORY GATEWAY ECU OK NO PLEASE CALL Fujitsu Ten Technical Support at (800) 237-5413 END * Please fax RES Replacement Authorization Request Form and Customer Problem Analysis Check to (800) 438-5410 to receive an authorization number before you change the parts.

INSPECTION 4/9 Remote Engine Starter Troubleshooting Guide Page 16 ENGINE DOES NOT STOP BY REMOTE. INSPECTION PROCEDURE (a) Ignition must be OFF when starting this procedure. 1 CHECK REMOTE KEYLESS ENTRY OPERATION (a) Press the UNLOCK button. (b) Confirm the doors are unlocked. OK NO 2 CHECK REMOTE ENGINE STOP OPERATION (a) Press the UNLOCK button once. OR (b) Press and hold the LOCK button for 2 seconds. OK GO TO VEHICLE S REPAIR MANUAL AND CHECK REMOTE KEYLESS ENTRY OPERATION END NO HINT: If the engine does not stop by remote: <Vehicle with Smart entry> Press the POWER button to stop the engine. <Vehicle without Smart entry> Disconnect the Remote Engine Starter ECU connector. 3-1 CHECK VEHICLE CIRCUIT (REMOTE ENGINE STARTER ECU AND ACCESSORY GATEWAY ECU INPUT/OUTPUT CHECK) Measure the voltage and resistance of each terminal on the wire harness for Remote Engine Starter ECU and Accessory Gateway ECU. Then, compare measured value to specifications. (See RES ECU and Accessory Gateway ECU pin layout and terminal information from pages 4 to 6 for specifications.) NO GO TO STEP 3-2 OK GO TO STEP4

INSPECTION 5/9 Remote Engine Starter Troubleshooting Guide Page 17 3-2 CHECK VEHICLE CIRCUIT (WIRE HARNESS CONTINUITY CHECK) Check for continuity of the wire harness. (See Installation Instruction and Electrical Wiring Diagram.) OK NO CHANGE REMOTE ENGINE STARTER WIRE HARNESS PLEASE VERIFY THE WIRE HARNESS CONNECTIONS If they are OK: CHANGE REMOTE ENGINE STARTER ECU AND ACCESSORY GATEWAY ECU 4 RETRY REMOTE ENGINE STOP OK END NO PLEASE CALL Fujitsu Ten Technical Support at (800) 237-5413 * Please fax RES Replacement Authorization Request Form and Customer Problem Analysis Check to (800) 438-5410 to receive an authorization number before you change the parts.

INSPECTION 6/9 Remote Engine Starter Troubleshooting Guide Page 18 ENGINE STOPS UNEXPECTEDLY INSPECTION PROCEDURE 1 CHECK THE REMOTE ENGINE STARTER TOTAL OPERATION TIME (a) Ask the customer the operation time and how the customer operates the Remote Engine Starter. (b) Remote start engine and let it run for 10 minutes. OK END HINT: EXPLAIN HOW ENGINE STARTER WORKS TO CUSTOMER: Any vehicles started with the Remote Engine Starter can idle for a total 20 minutes. Automatic engine shutdown occurs after 10 minutes, but the vehicle may be remotely started as many times as the user wishes and run for an additional 10 minutes. After 20 minutes of total operation, however, the vehicle must be started manually to reset the Remote Engine Starter. NO 2 CHECK REMOTE ENGINE STARTER DIAGNOSIS (a) Please check the diagnostic code by scan tool. (See Diagnostic Code by Scan Tool on page 12). If [B2334] or [B2333] is indicated, please call Fujitsu Ten Technical Support at (800) 237-5413. (b) Connect the diagnostic connectors to enter the Diagnostic Mode. (See Diagnostic Operation on page 10 for the location of the connectors). If the connectors are already plugged in, please disconnect and plug them in again. (c) Check the factor to stop the engine by applying the brake in Diagnostic Mode. Hazard lights will flash in accordance with the factor of engine stop. (See Diagnostic Factor Identification on page 11.) Number of hazard light flashes: 1 to 10 GO TO STEP 3-1 Number of hazard light flashes: 0 GO TO STEP 5-2

INSPECTION 7/9 Remote Engine Starter Troubleshooting Guide Page 19 3-1 CHECK VEHICLE CIRCUIT (REMOTE ENGINE STARTER ECU AND ACCESSORY GATEWAY ECU INPUT/OUTPUT CHECK) Measure the voltage and resistance of the affected terminals (listed on page 11) on the wire harness for Remote Engine Starter ECU and Accessory Gateway ECU. Then, compare measured value to specifications. (See RES ECU and Accessory Gateway ECU pin layout and terminal information from pages 4 to 6 for specifications.) OK NO GO TO STEP 3-3 3-2 CHECK VEHICLE CIRCUIT (REMOTE ENGINE STARTER ECU AND ACCESSORY GATEWAY ECU INPUT/OUTPUT CHECK) Measure the voltage and resistance of the other or all terminals on the wire harness for Remote Engine Starter ECU and Accessory gateway ECU. Then, compare measured value to specifications. (See RES ECU and Accessory Gateway ECU pin layout and terminal information from pages 4 to 6 for specifications.) NO GO TO STEP 3-3 OK PLEASE CALL (800) 237-5413. 3-3 CHECK VEHICLE CIRCUIT (WIRE HARNESS CONTINUITY CHECK) Check for continuity of the wire harness. (See Installation Instruction and Electrical Wiring Diagram.) OK NO PLEASE VERIFY THE WIRE HARNESS CONNECTIONS If they are OK: CHANGE REMOTE ENGINE STARTER ECU AND ACCESSORY GATEWAY ECU CHANGE REMOTE ENGINE STARTER WIRE HARNESS * Please fax RES Replacement Authorization Request Form and Customer Problem Analysis Check to (800) 438-5410 to receive an authorization number before you change the parts.

INSPECTION 8/9 Remote Engine Starter Troubleshooting Guide Page 20 FAILED REGISTRATION OF IMMOBILIZER ID CODE INSPECTION PROCEDURE 1 CONFIRM THE PROCEDURE OF REGISTRATION (a) See the installation instructions posted on TIS for the ID code registration process. (b) For any assistance with the registration process, call Fujitsu Ten Technical Support at (800) 237-5413. NEXT 2 RETRY REGISTRATION OF IMMOBILIZER ID CODE (a) VEHICLES WITH SMART ENTRY Retry registration slowly with scan tool. NO GO TO STEP 3-1 OK END (b) VEHICLES WITHOUT SMART ENTRY Retry manual registration slowly. NO OK END 3-1 CHECK VEHICLE CIRCUIT (REMOTE ENGINE STARTER ECU AND ACCESSORY GATEWAY ECU INPUT/OUTPUT CHECK) Measure the voltage and resistance of each terminal on the wire harness for Remote Engine Starter ECU and Accessory gateway ECU. Then, compare measured value to specifications. (See RES ECU and Accessory Gateway ECU pin layout and terminal information from pages 4 to 6 for specifications.) OK GO TO STEP 4 NO GO TO STEP 3-2

INSPECTION 9/9 Remote Engine Starter Troubleshooting Guide Page 21 3-2 CHECK VEHICLE CIRCUIT (WIRE HARNESS CONTINUITY CHECK) Check for continuity of the wire harness. (See Installation Instruction and Electrical Wiring Diagram.) OK NO PLEASE VERIFY THE WIRE HARNESS CONNECTIONS If they are OK: CHANGE REMOTE ENGINE STARTER ECU AND ACCESSORY GATEWAY ECU CHANGE REMOTE ENGINE STARTER WIRE HARNESS 4 RETRY REGISTRATION NO CHANGE REMOTE ENGINE STARTER ECU AND ACCESSORY GATEWAY ECU OK END * Please fax RES Replacement Authorization Request Form and Customer Problem Analysis Check to (800) 438-5410 to receive an authorization number before you change the parts.

2010- LAND CRUISER TVIP V4 REMOTE ENGINE STARTER (RES) ELECTRICAL WIRING DIAGRAM (EWD) DOME 1 LH-IG ENGINE CONTROL MODULE A4 W-R W-R B4 W-R BODY ECU IG1 RELAY ECU-IG1 SHORT PIN LH-J/B ALTER A3 R R R R B3 METER E6 E6 H1 H2 V R V R F1 F2 GATEWAY ECU F5 F3 L R F4 W-B R W-B G1 FE6 D8 G G G C8 FE6 IE2 K3 R R R J3 IE2 W-B W-B W-B BATTERY R W-R L R G E6 E9 E1 E11 E12 N1 M1 W-B W-B W-B Y E16 E17 E8 E4 REMOTE ENGINE STARTER ECU Connector to Connector Vehicle Connector TVIP Harness Vehicle Harness Splice Connection (Splicing Connector) TVIP or Vehicle Terminal Insert Draft1: 03/23/09

2010- LAND CRUISER TVIP V4 REMOTE ENGINE STARTER (RES) CONNECTORS A B C D 3 4 (FEMALE PIN) 4 3 (MALE PIN) 2 3 4 6 7 8 9 5 10 5 4 3 2 10 9 8 7 6 (FEMALE PIN) (MALE PIN) E F G H 1 4 6 8 9 11 12 16 17 1 2 3 4 5 1 (TERMINAL PIN) 2 1 (FEMALE PIN) (FEMALE PIN) (MALE PIN) J K M N 10 11 2 3 4 6 7 8 9 20 12 18 19 (FEMALE PIN) 10 20 9 8 7 6 4 3 2 11 19 18 12 1 1 (MALE PIN) (FEMALE PIN) (MALE PIN) Draft1: 03/23/09

TOYOTA LAND CRUISER 2013 - TVIP V4 Preparation REMOTE ENGINE STARTER (RES) Part Number: PT398-60140 Conflicts Will not program with Techstream Lite. Recommended Sequence of Application Item # Accessory 1 XM XM Radio 2 TVIP V2 Glass Breakage Sensor (GBS) and/or V4 Remote Engine Starter (RES) Kit Contents Item # Quantity Description 1 1 Wire Harness 2 1 RES ECU Bracket 3 1 Extra Large Wire Tie Hardware Bag Contents Item # Quantity Description 1 1 RES ECU 2 1 Gateway ECU 3 1 Gateway ECU Bracket 4 1 M6 Tapping Screw 5 15 Wire Ties 6 1 Waterproof Sheet 7 2 Large Foam Tape (1sheet - 2pcs) 8 1 Custom Double Stick Tape 9 2 Key Tag (English) 10 2 Window Labels (English) 11 2 Transmitter Labels (English) 12 1 Engine Room Warning Label (English) 13 2 Key Tag (Spanish) 14 2 Window Labels (Spanish) 15 2 Transmitter Labels (Spanish) 16 1 Engine Room Warning Label (Spanish) 17 1 Owner s Guide Additional Items Required For Installation Item # Quantity Description 1 1 Black Electrical Tape Recommended Tools Personal & Vehicle Protection Safety Glasses Safety Gloves Vehicle Protection Special Tools Techstream Installation Tools Screwdriver Nylon Panel Removal Tool Side Cutters Torque Wrench Utility Knife Pliers Tape Wrench Socket Special Chemicals Cleaner Glass Cleaner Legend Notes (Optional) Blankets, Parts Boxes Notes Do not use Techstream Lite Notes #2 Phillips e.g. Panel Pry Tool #1 Toyota SST # 00002-06001-01 36 in lbf (4.07 N m) 88.5 in lbf (10 N m) Clip Clamp Pliers Clear 10mm 10mm, Extension, 10mm Deep Notes VDC Approved Cleaner Household Glass Cleaner STOP: Damage to the vehicle may occur. Do not proceed until process has been complied with. OPERATOR SAFETY: Use caution to avoid risk of injury. CAUTION: A process that must be carefully observed in order to reduce the risk of damage to the accessory/vehicle and to ensure a quality installation. TOOLS & EQUIPMENT: Used in Figures calls out the specific tools and equipment recommended for this process. REVISION MARK: This mark highlights a change in installation with respect to previous issue. SAFETY TORQUE: This mark indicates that torque is related to safety. Care must be taken when installing this accessory to ensure damage does not occur to the vehicle. The installation of this accessory should follow approved guidelines to ensure a quality installation. These guidelines can be found in the "Accessory Installation Practices" document. This document covers such items as: Vehicle Protection (use of covers and blankets, cleaning chemicals, etc.) Safety (eye protection, rechecking torque procedure, etc.) Vehicle Disassembly/Reassembly (panel removal, part storage, etc.) Electrical Component Disassembly/Reassembly (battery disconnection, connector removal, etc.) Please see your Toyota dealer for a copy of this document. Page 1 of 26 pages

TOYOTA LAND CRUISER 2013 - TVIP V4 Procedure REMOTE ENGINE STARTER (RES) TVIP A B C D E F G H I J K L M N Vehicle Description 5P WHITE 5P WHITE 10P WHITE 10P WHITE 20P WHITE for RES ECU 5P WHITE for Gateway ECU GROUND WIRE TERMINAL 2P WHITE Gateway ECU 20P BLUE 20P BLUE RES ECU 1P WHITE (RES Diagnosis) 1P WHITE (RES Diagnosis) Page 2 of 26 pages

TOYOTA LAND CRUISER 2013 - TVIP V4 Procedure REMOTE ENGINE STARTER (RES) 1. Vehicle Disassembly. 10mm Socket Negative Battery Cable (a) Place the Vehicle in Park with the Parking Brake set. (b) Remove the Negative Battery Cable. (Fig. 1-1) (1) Protect the Fender before starting. (2) Note the Battery Cable position, as it will be reinstalled in the same position. CAUTION: Do not touch the positive terminal. Fig. 1-1 1 Glove Box Under Cover 2 PS Dash Side Cover 3 PS Step Cover 4 PS Cowl Cover 5 PS Knee Panel 6 PS Cluster Side Panel 7 PS Knee Airbag 8 Glove Box 9 DVD Unit Fig. 1-2 Fig. 1-2 Page 3 of 26 pages Remove all corresponding connectors accordingly as you disassemble.

TOYOTA LAND CRUISER 2013 - TVIP V4 Procedure REMOTE ENGINE STARTER (RES) Nylon Panel Removal Tool (c) Remove the Glove Box Under Cover. (Fig. 1-3) (1) Begin by protecting the Vehicle Interior with Blankets. Fig. 1-3 Glove Box Under Cover Nylon Panel Removal Tool (d) Remove the Passenger s Side Dash Side. Cover. (Fig. 1-4) Dash Side Cover Fig. 1-4 Nylon Panel Removal Tool (e) Remove the Passenger s Side Step Cover. (Fig. 1-5) Fig. 1-5 Step Cover Nylon Panel Removal Tool Cowl Cover (f) Remove the Passenger s Side Cowl Cover. (Fig. 1-6) (1) Remove 1 Nut. Fig. 1-6 Nut Page 4 of 26 pages

TOYOTA LAND CRUISER 2013 - TVIP V4 Procedure REMOTE ENGINE STARTER (RES) Nylon Panel Removal Tool (g) Remove the Passenger s Side Knee Panel. (Fig. 1-7) Knee Panel Fig. 1-7 Phillips Screwdriver, Nylon Panel Removal Tool Screw (h) Remove the Passenger s Side Cluster Side Panel. (Fig. 1-8) (1) Remove 1 Screw and 1 Clip. Cluster Side Panel Clip Fig. 1-8 10mm Socket, Nylon Panel Removal Tool (i) Remove the Passenger s Knee Air Bag. (Fig. 1-9) Bolts (x2) Fig. 1-9 Knee Air Bag Bolts (x2) (1) Remove 4 Bolts. (2) Do not disconnect the Vehicle s Connector. CAUTION: Sharp metal edges. Knee Air Bag (j) Wrap the Passenger s Knee Air Bag in a Blanket and use the TVIP Kit Box to support it. (Fig. 1-10) CAUTION: Sharp metal edges. Fig. 1-10 TVIP Box Page 5 of 26 pages

TOYOTA LAND CRUISER 2013 - TVIP V4 Procedure REMOTE ENGINE STARTER (RES) Phillips Screwdriver (k) Remove 2 Screws from the bottom of the Glove Box. (Fig. 1-11) Fig. 1-11 Screws (x2) Bolt Nylon Panel Removal Tool, 10mm Socket Cover (l) Open the Glove Box, remove 2 Bolt Covers from the Glove Box. (Fig. 1-12) (m) Dislodge the Glove Box (Fig. 1-12) Cover Bolt (1) Remove 2 Bolts. NOTE: Pull down and out to avoid damaging the Vehicle Clips or Dash Trim. Fig. 1-12 Glove Box Glove Box (backside) (n) Remove the Vehicle Harness from the backside of the Glove Box, remove the Glove Box. (Fig. 1-13) (1) Disconnect any Connectors. Vehicle Harness Fig. 1-13 10mm Socket Knee Air Bag (o) Temporarily install the Passenger's Side Knee Air Bag. (Fig. 1-14) CAUTION: Sharp metal edges. Bolts (x2) Fig. 1-14 Bolts (x2) Page 6 of 26 pages

TOYOTA LAND CRUISER 2013 - TVIP V4 Procedure REMOTE ENGINE STARTER (RES) 10mm Deep Socket, Clip Clamp Pliers, Screwdriver DVD Unit Nut Screw VEHICLES EQUIPPED WITH NAVIGATION SYSTEM. (p) Remove the DVD Unit from the Glove Box Area. (Fig. 1-15) (1) Remove 2 Screws and 1 Nut. Fig. 1-15 Screw Clamp (2) Using the Clip Clamp Tool or the like, push on the inside the Vehicle Clamp, and release it from the DVD Unit. Brace 2. V4 Wire Harness Installation. V4 Harness V4 Harness (a) Route the V4 Harness behind the Vehicle Brace and Yellow Harness in the Glove Box area as shown. (Fig. 2-1) CAUTION: Sharp metal edges. Fig. 2-1 White Tape Vehicle s Yellow Harness Side Cutter Wire Ties (x3) (b) Secure the V4 Harness's White Taped Marker to the Reinforcement with 1 Wire Tie. (Fig. 2-2) Fig. 2-2 V4 Harness White Tape Marker 5P V4 Harness (c) Secure the V4 Harness to the Reinforcement with 2 Wire Ties. (Fig. 2-2) 10mm Socket Vehicle s Ground Terminal (d) Locate and remove 1 Bolt from the Vehicle Ground Terminal in the upper left side of the Glove Box Area. (Fig. 2-3) (1) Do not discard the Bolt. Bolt Fig. 2-3 V4 Harness s Ground Terminal Page 7 of 26 pages

TOYOTA LAND CRUISER 2013 - TVIP V4 Procedure REMOTE ENGINE STARTER (RES) Vehicle's Ground Terminal 10mm Socket V4 Harness's Ground Terminal (e) Use the existing Vehicle's Bolt to secure the V4 Harness's Ground Terminal with the Vehicle's Ground Terminal. (Fig. 2-4) (1) Make sure that the Vehicle's Ground Terminal Pin seats properly. Fig. 2-4 Bolt (f) Locate and remove the Vehicle's White 10P Connector from the Connector Block in the Glove Box Area. (Fig. 2-5) Vehicle s 10P (White) Fig. 2-5 Passenger's Side Connector Block Vehicle Harness' White 10P V4 Harness' White 10P V4 Harness' White 10P (g) Plug in the V4 Harness s White 10P Connectors in between the Vehicle Harness s White 10P Connector and the Connector Block. (Fig. 2-6) V4 Harness (1) Verify secure connection. Fig. 2-6 Passenger's Side Connector Block Vehicle Harness 10P V4 Harness (h) Push the 10P Connectors through the opening between the Vehicle Harness and the Passenger's Side Connector Block as shown. (Fig. 2-7) Fig. 2-7 Passenger's Side Connector Block Page 8 of 26 pages

TOYOTA LAND CRUISER 2013 - TVIP V4 Procedure REMOTE ENGINE STARTER (RES) Wire Tie Vehicle Harness Side Cutter 10P Connectors V4 Harness Wire Tie Vehicle Harness (i) Secure the 10P Connectors to the Vehicle Harness with 1 Wire Tie. (Fig. 2-8) (j) Secure the V4 Harness to the Vehicle Harness behind the Passenger's Side Connector Block with 1 Wire Tie. (Fig. 2-8) Fig. 2-8 V4 Harness Large Foam Tape (k) Wrap the V4 Harness s branch area with 1 Large Foam Tape as shown. (Fig. 2-9) (l) Route the V4 Harness's White 20P Connector toward the Vehicle's Floor. (Fig. 2-9) Fig. 2-9 V4 20P (White) 3. RES ECU Preparation and Installation. Yellow Sheet (Vehicle Side) Double-Side Adhesive Tape (a) Remove the Clear Protective Sheet from the Double Stick Tape and attach it to the Part Number Label side of the RES ECU as shown. (Fig. 3-1) Clear Sheet (RES ECU Side) Fig. 3-1 RES ECU Part Number Label (1) Be sure to apply the Clear Sheet side on the RES ECU. (2) Be sure to attach adhesive tape on the part number label side of the RES ECU. (3) Do not cover the Part Number Label with the adhesive tape. CAUTION: Do not touch the adhesive surface. Page 9 of 26 pages

TOYOTA LAND CRUISER 2013 - TVIP V4 Procedure REMOTE ENGINE STARTER (RES) Waterproof Sheet (b) Remove the Backing Sheet of 1 Waterproof Sheet and attach it to the RES ECU near the connectors as shown. (Fig. 3-2) CAUTION: Do not touch the adhesive surface. Fig. 3-2 RES ECU (c) Insert the RES ECU Bracket into the indicated Bracket Slots on the RES ECU. (Fig. 3-3) RES ECU Bracket (1) Ensure the Bracket is firmly attached to the ECU. Fig. 3-3 RES ECU (d) Apply 1 strip of Large Foam Tape to the RES ECU as shown. (Fig. 3-4) Large Foam Tape Fig. 3-4 RES ECU (e) Turn over the Floor Carpet on the left side of the Passenger's Side Area. (Fig. 3-5) (f) Pull back the Felt on the backside of the Floor Carpet as shown. (Fig. 3-5) Felt (1) Do not remove or cut off the Felt. Fig. 3-5 Floor Carpet Page 10 of 26 pages

TOYOTA LAND CRUISER 2013 - TVIP V4 Procedure REMOTE ENGINE STARTER (RES) Bolt Portion of the Protective Bracket Fig. 3-6 RES ECU 20P V4 Harness Floor Carpet (g) Connect the V4 Harness's White 20P Connector to the RES ECU. (Fig. 3-6) (h) Using the VDC approved cleaner and Cleaning Method, clean the area indicated on the left side of the Passenger s Side Floor. (Fig. 3-6) (i) Remove the Protective Sheet of the Double Stick Tape. (Fig. 3-6) (j) Center the RES ECU Bracket to Vehicle's Bolt as shown. Then press the RES ECU firmly to the Vehicle. (Fig. 3-6) (1) Do not attempt to reposition the ECU once placed. Extra Large Wire Tie Side Cutter Vehicle s Brace V4 Harness (k) Run 1 Extra Large Wire Tie through the RES ECU rectangular hole and behind the Vehicle Brace and secure it. (Fig. 3-7) (1) Do not tighten the Wire Tie, it should hang freely. Fig. 3-7 ECU Bracket s Rectangular Hole RES ECU Side Cutter Wire Tie Vehicle s Brace V4 Harness (l) Secure the V4 Harness to the side of the inside Vehicle Brace with 1 Wire Tie as shown. (Fig. 3-8) (1) Do not use the front hole of the Vehicle Brace. Hole Fig. 3-8 RES ECU Page 11 of 26 pages

TOYOTA LAND CRUISER 2013 - TVIP V4 Procedure REMOTE ENGINE STARTER (RES) Vehicle s Brace Large Foam Tape (m) Attach 1 Large Foam Tape to the Vehicle s Brace and the V4 Harness as shown. then put the Carpet back. (Fig. 3-9) RES ECU GO BACK TO THE V4 HARNESS S WHITE TAPE MARKER AREA. Fig. 3-9 Carpet Gateway ECU Bracket Connector Fig. 4-1 Gateway ECU 4. Gateway ECU Preparation and Installation. (a) Insert the Gateway ECU Bracket into the indicated Bracket Slots on the Gateway ECU. (Fig. 4-1) (1) Ensure the Bracket is firmly attached to the ECU. 10mm Socket Hole V4 Harness (b) Connect the V4 Harness's White 5P Connector to the Gateway ECU. (Fig. 4-2) (1) Verify secure connection. Pin 5P (c) Using the M6 Tapping Screw from the Kit, install the Gateway ECU Bracket. (Fig. 4-2) (1) Make sure that the Bracket Pin seats properly. Fig. 4-2 Tapping Screw Gateway ECU CAUTION: Do not crimp the V4 and/or the V2 Harness between the Gateway ECU Bracket and the Vehicle Reinforcement Brace. Page 12 of 26 pages

TOYOTA LAND CRUISER 2013 - TVIP V4 Procedure REMOTE ENGINE STARTER (RES) Side Cutter Wire Tie 5. V4 Wire Harness Installation (continued). (a) Route the V4 Harness behind the Vehicle Brace and ECU Brackets as shown. (b) Secure the V4 Harness to the Vehicle Brace with 1 Wire Tie. (Fig. 5-1) Fig. 5-1 (c) Locate the Vehicle s 5P White Connectors. (Fig. 5-2) (d) Disconnect the Vehicle s 5P White Connectors. (Fig. 5-2) Fig. 5-2 (e) Connect the V4 5P Connectors in between the Vehicle s 5P Connectors. (Fig. 5-3) Fig. 5-3 Side Cutter (f) Secure the V4 Harness to the Vehicle Harness with 1 Wire Tie. (Fig. 5-4) (g) Secure the 5P Connectors to the Vehicle Harness with 1 Wire Tie. (Fig. 5-4) Fig. 5-4 Page 13 of 26 pages

TOYOTA LAND CRUISER 2013 - TVIP V4 Procedure REMOTE ENGINE STARTER (RES) (h) Locate the Vehicle s 2P Pre-Connector. (Fig. 5-5) 2P Pre- Connector (i) Remove the Break Away Tape from the Connector. (Fig. 5-5) Fig. 5-5 (j) Connect the V4 2P Connector to the Vehicle s 2P Pre-Connector. (Fig. 5-6) Fig. 5-6 Side Cutter (k) Secure the 2P Connectors to the Vehicle Harness with 1 Wire Tie. (Fig. 5-7) Fig. 5-7 Side Cutter (l) Route the remaining V4 Harness along the Vehicle Harness towards the Passenger s Cowl Area. (Fig. 5-8) (m) Secure the V4 Harness to the Vehicle Harness using 1 Wire Tie. (Fig. 5-8) Fig. 5-8 Page 14 of 26 pages

TOYOTA LAND CRUISER 2013 - TVIP V4 Procedure REMOTE ENGINE STARTER (RES) Side Cutter (n) Route the remaining V4 Harness as shown. (Fig.5-9) CAUTION: Do not secure the V4 1P RES Diagnostic Connectors. (o) Secure the V4 Harness to the Vehicle Harness with 1 Wire Tie. (Fig. 5-9) Fig. 5-9 (p) Disconnect the Vehicle s Blue 20P Connector from the Passenger s Side Cowl Area. (Fig. 5-10) Fig. 5-10 (q) Connect the V4 20P Connectors in between the Vehicle s 20P Connectors. (Fig. 5-11) Fig. 5-11 Side Cutter (r) Secure the 20P Connectors to the Vehicle Harness with 1 Wire Tie. (Fig. 5-12) Fig. 5-12 Page 15 of 26 pages

TOYOTA LAND CRUISER 2013 - TVIP V4 Procedure REMOTE ENGINE STARTER (RES) 6. Partial Reassembly. (a) Reassemble the Vehicle, except for the Passenger's Cowl Cover, and Step Cover. Fig. 6-1 EXAMPLE Install Short Pin (1) Reconnect any disconnected connectors. (2) Torque the Passenger s Knee Air Bag to 88.5 in lbf (10 N m). (b) Verify the Short Pin is installed. (Fig. 6-1) (1) If not, install the Short Pin. 7. Registration Process. (a) Open the Hood. (Fig. 7-1) Note: Do not close the Hood during the Registration Setting Procedure. (Steps b-cc) Fig. 7-1 Negative Battery Cable (b) Temporarily reconnect the Vehicle's Negative Battery Cable. (Fig. 7-2) CAUTION: Do not touch the positive terminal. Fig. 7-2 Battery RES Diagnostic 1P Connectors Fig. 7-3 V4 Harness (c) Locate the V4 Harness s 1P RES Diagnostic Connectors in the Passenger s Side Cowl Area, and remove the Tape. (Fig. 7-3) (d) Connect the 2 RES Diagnostic Connectors. (Fig. 7-3) Page 16 of 26 pages

TOYOTA LAND CRUISER 2013 - TVIP V4 Procedure REMOTE ENGINE STARTER (RES) EXAMPLE (e) Ensure all Doors are closed and the Smart Key is in your possession. (Fig. 7-4) (f) Cycle the Vehicle s Engine Start Stop Button from OFF to ON 5 times. (Fig. 7-4) Fig. 7-4 (1) Place the Shift Lever in the "P" Position. NOTE: One cycle consists of: OFF Accessory ON This is equivalent to pressing the Engine Start Stop Button 14 times. (g) Once the fifth cycle has been completed, the Hazard Lights Flash once. (Fig. 7-4) (h) Press the Vehicle s Engine Start Stop Button once more to turn the ignition to OFF. EXAMPLE SUCCESS (i) Start the Engine, after 10 seconds stop the Engine. (Fig. 7-5) (j) The Hazard Lights flash once. (Fig. 7-5) Go to step m. Fig. 7-5 RES Diagnostic 1P Connectors Fig. 7-6 (k) If this procedure failed, the Hazard Lights flash twice. (l) Disconnect the RES Harness White 1P Connectors from the Passenger s Side Cowl Area. (Fig. 7-6) Start again from step d. Page 17 of 26 pages

TOYOTA LAND CRUISER 2013 - TVIP V4 Procedure REMOTE ENGINE STARTER (RES) Vehicle Diagnostic Port Techstream Notebook CAUTION: Techstream Lite will not work for this section, use the Techstream Notebook ONLY. Fig. 7-7 (m) (n) Connect the Techstream Notebook to the Vehicle s Diagnostic Port. (Fig. 7-7) With the Remote Control Key in your possession, press the Vehicle s Engine Start Stop Button twice to select the Ignition ON position. Note: Do not apply Brake Pedal. (o) Start the TIS Techstream Application by clicking on the shortcut located on the Desktop. (p) Click Connect to Vehicle. (Fig. 7-8) Fig. 7-8 Others (q) Confirm that the information displayed on the Vehicle Connection Wizard is correct for the Vehicle. If not verify that the Techstream is properly connected. (Fig. 7-9) (r) Under Option, select Others then Click Next>. (Fig. 7-9) Fig. 7-9 Page 18 of 26 pages

TOYOTA LAND CRUISER 2013 - TVIP V4 Procedure REMOTE ENGINE STARTER (RES) (s) Select Smart Access. (Fig. 7-10) (t) Click. (Fig. 7-10) Fig. 7-10 (u) Click on Utility. (Fig. 7-11) (v) Select ECU Communication ID Registration. (Fig. 7-11) (w) Click. (Fig. 7-11) Fig. 7-11 (x) Confirm that the Engine is ON (IG), and that the Smart Cancel Function is OFF. (Fig. 7-12) (y) Click Next> to continue. (Fig. 7-12) Fig. 7-12 Page 19 of 26 pages

TOYOTA LAND CRUISER 2013 - TVIP V4 Procedure REMOTE ENGINE STARTER (RES) (z) Select Remote Engine Starter. (Fig. 7-13) (aa) Click Next> to continue. (Fig. 7-13) Fig. 7-13 (bb) Click Exit. (Fig. 7-14) Fig. 7-14 (cc) Click. (Fig. 7-15) Fig. 7-15 Example Page 20 of 26 pages

TOYOTA LAND CRUISER 2013 - TVIP V4 Procedure REMOTE ENGINE STARTER (RES) EXAMPLE (dd) Close the Hood. (Fig. 7-16) (ee) The Hazard Lights flash twice. Registration is completed (Fig. 7-16) Fig. 7-16 If this procedure failed, the Hazard Lights flash 3 times. Registration was not set. Disconnect the 1P RES Diagnostic Connectors, then open the Hood. Start again from Step d. V4 Diagnostic 1P Connectors (ff) Disconnect the V4 Harness's 1P RES Diagnostic Connectors. (Fig. 7-17) Fig. 7-17 Electrical Tape (gg) Secure the V4 Harness and 1P Connectors with Electrical Tape as shown. (Fig. 7-17) (hh) Secure the V4 Harness to the Vehicle Harness with the Electrical Tape as shown. (Fig. 7-17) (ii) Press the Vehicle s Engine Start Stop Button to place the Vehicle in the "OFF" (Indicator Light off) position. Page 21 of 26 pages

TOYOTA LAND CRUISER 2013 - TVIP V4 Procedure REMOTE ENGINE STARTER (RES) 8. Tags and Label Installation. For US Vehicles use the English Labels and discard the Spanish Labels. For Mexico Vehicles use the Mexico Labels, and discard the English Labels. (a) Remove 2 of the Remote Controls from their protective bag. Utility Knife, Clear Tape 4 Button Key 3 Button Key (1) Use a utility knife, to cut a slit in each bag. (b) Using VDC approved cleaner and Cleaning Method, clean the area indicated on the Remote Controls. (Fig. 8-1) Key Label 2mm Key Label 2mm (c) Attach the Key Label to the Remote Controls as shown. (Fig. 8-1) (1) Use a piece of the clean adhesive tape to lift the labels off their protective backing. Fig. 8-1 CAUTION: Do not touch the adhesive surface. (d) Attach the Remote Engine Starter Tags to the Vehicle Remote Controls. (Fig. 8-2) Key Tag Fig. 8-2 Clear Tape (e) Using VDC approved cleaner and Cleaning Method, clean the area indicated on the Engine Compartment Cover.(Fig. 8-3) (f) Attach the Warning Label to the Engine Compartment Cover as shown. (Fig. 8-3) CAUTION: Do not touch the adhesive surface. Fig. 8-3 Page 22 of 26 pages

TOYOTA LAND CRUISER 2013 - TVIP V4 Procedure REMOTE ENGINE STARTER (RES) Clear Tape (g) Use Household Glass Cleaner to clean the inside of the Front Door Window. (Fig. 8-4) Molding Etching Etching (h) Use a piece of Clear Tape to lift the Label off its protective backing. CAUTION: Do not touch the adhesive surface. (i) Attach the Label as shown. (Fig. 8-4) Fig. 8-4 Molding NOTE: Make sure to Align according to Etching or Other Label. (Fig. 8-4) REPEAT: steps g i with the other Window. Fig. 9-1 Utility Knife Large Foam Tape ⅓Foam Tape Glove Box (backside) 9. Completing the Installation. (a) Cut and apply ⅓ piece of Large Foam Tape to the backside of the Glove Box. (Fig. 9-1) (b) Complete the reassembly of the Vehicle. (1) Verify the Panels fit together properly, with no uneven gaps. Torque Wrench Negative Battery Cable (c) Position the Negative Battery Cable at the original factory position. (Fig. 9-2) (1) Tighten the Nut to 36 in lbf (4.07 N m) CAUTION: Do not touch the positive terminal. (d) Clean up and remove any Trash. Fig. 9-2 Battery (e) Sealed in its protective Bag, place the Owner s Guide in the Glove Box. (f) Reset the power windows. (1) Press the Power Button to select the Ignition ON position. (2) Push down on the Power Window Switches lowering the windows halfway. (3) Pull up on the switches until the windows close (4) Continue holding up on the Switches for a minimum of 1 second. Page 23 of 26 pages

TOYOTA LAND CRUISER 2013 TVIP V4 CHECKLIST These points MUST be checked to ensure a quality installation. REMOTE ENGINE STARTER (RES) Accessory Function Checks Close the hood, enter the vehicle and close all doors. Place the shift lever in the P (Park) position, set the parking brake and make sure the Vehicle is off. Perform 1 Press the remote control s lock button twice within 2 seconds, then press and hold the lock button for 3 seconds. 2 With the engine running, pull the hood release handle. NOTE: Some Vehicles may require you to exit the Vehicle and pull up on the Hood. 3 Move the shift lever out of P (Park). Attempt to start the Vehicle using the remote. Look For The hazard lights flash after 3 seconds. The engine starts. The hazard lights flash repeatedly for 20 seconds. The engine stops. The hazard lights flash once. The security alarm triggers (only if equipped with OE Factory Alarm, not Genuine Accessory alarm, and only if armed) The engine does not start. Vehicle Appearance Check Perform After accessory installation and removal of protective cover(s), perform a visual inspection of the vehicle. Look For Ensure no damage (including scuffs and scratches) was caused during the installation process. (For PPO installations, refer to TMS Accessory Quality Shipping Standard.) Page 24 of 26 pages

TOYOTA LAND CRUISER 2013 - TVIP V4 Checklist - these points MUST be checked to ensure a quality installation. REMOTE ENGINE STARTER (RES) Vehicle Function Check Function Function Head Light ABS Light (if equipped) If the warning light remains on, it may indicate a system malfunction. High Beams Rear Wiper/Washer (if equipped) Turn Signal Lights Clock (if equipped) Tail Lights Accessory Power Socket (if equipped) Stop Lights Starter Backup Lights Audio/Video (if equipped) Hazard Lights Power Sliding Door (if equipped) Marker Lights Convenience Memory Settings (if equipped) Dome/Courtesy Lights Heated Seats (if equipped) Panel/Switch Illumination Massage Seats (if equipped) Accessory Controls/Illumination (if equipped) Rear Window Defogger (if equipped) Key Sensor Buzzer Power Side Mirrors (if equipped) Fog Lights (if equipped) Side Mirror Defogger (if equipped) Daytime Running Lights Front Windshield Defogger (if equipped) (if equipped) Trunk/Tailgate/Bed Lights Navigation System (if equipped) (if equipped) Glove Box Light (if equipped) Rear Sunshade (if equipped) Cruise Control Light (if equipped) Steering Wheel Audio Control (if equipped) Steering Wheel Column Adjusts Without Interference Seat Belt Warning Light If the warning light remains on, it may indicate a system malfunction. Page 25 of 26 pages

Side Cutter TOYOTA LAND CRUISER 2013 - TVIP V4 Checklist - these points MUST be checked to ensure a quality installation. REMOTE ENGINE STARTER (RES) Function Air Bag Warning Light If the warning light remains on, it may indicate a system malfunction. Track/Skid Control Light (if equipped) If the warning light remains on, it may indicate a system malfunction. Function Lamp Failure Sensor If the warning light remains on, it may indicate a system malfunction. Front Wiper/Washer HVAC Hood Latch Release Power Locks (if equipped) Passenger Air Bag Switch (if equipped) Power Windows (if equipped) Rollover Side Curtain Air Bag Switch (RSCA) (if equipped) Power Seats (if equipped) Tire Pressure Monitoring System (TPMS) (if equipped) Horn Gauges Power Sunroof (if equipped) Prior to TPMS activation and Pre-delivery Service (PDS) of the Vehicle the TPMS light will blink when IG is turned on. After TPMS activation and PDS of the Vehicle the TPMS light will illuminate for a few seconds and go off when IG is turned on. Remove the short pin after Function check. Check with your Port/Dealer to see if this step is necessary. Store Short Pin Here Page 26 of 26 pages