INSTLLTION INSTRUCTIONS FOR PRT 95-734 PPLICTIONS KI Optima 006.5-00 95-734 KIT FETURES Double DIN radio provision Stacked ISO units provision KIT COMPONENTS ) Double DIN Trim Plate ) Double DIN rackets WIRING ND NTENN CONNECTIONS (Sold Separately) Harness: 70-004 - Hyundai 006-up/KI harness 004-up 70-7303 - Hyundai / KI Harness 009 ntenna dapter: 40-KI - 009-0 Kia Optima TOOLS REQUIRED: Phillips Screwdriver Small Flat lade Screwdriver/ Panel Removal Tool -800--093 www.metraonline.com COPYRIGHT 004-0 METR ELECTRONICS CORPORTION
95-734 TLE OF CONTENTS Dash Disassembly - Kia Optima 006.5-00.................................. Kit ssembly * - Double DIN Radio Provision................................. - Stacked ISO Units Provision................................. 3 Final ssembly........................................... 4 *Note: Refer also to the instructions included with the aftermarket radio.
TEMP FM M SEEK TRCK RDM FF 95-734 DSH DISSSEMLY KI OPTIM 006.5-00 Disconnect the negative battery terminal to prevent an accidental short circuit. Unclip and remove the panel surrounding the radio including the a/c vents and climate controls. (Figure ) PUSH /C POWER VOLUME 3 4RPT 5 03.9 REW 3 Remove (4) Phillips screws securing radio. Unplug and remove radio. (Figure ) PUSH Continue to kit assembly. 3:05 EQ FM M 03.5 FM CD SCN POWER UDIO SEEK TRCK 4 RPT 5 3RDM FF REW 6 VOLUME TUNE
95-734 KIT SSEMLY DOULE DIN RDIO PROVISION *Note: Refer also to the instructions included with the aftermarket radio. Snap the Double DIN brackets to the inside edge of the Double DIN trim plate. (Figure ) Slide the Double DIN radio into the bracket/trim plate assembly and secure the radio to the assembly using the screws supplied with the radio. (Figure ) Continue to final assembly.
95-734 KIT SSEMLY STCKED ISO UNITS PROVISION *Note: Refer also to the instructions included with the aftermarket radio. Snap the Double DIN brackets to the inside edge of the Double DIN trim plate. (Figure ) Slide the stacked ISO units into the bracket/radio housing assembly and secure the units to the kit using the screws supplied with the units. (Figure ) Continue to final assembly. 3
95-734 FINL SSEMLY FINL SSEMLY C () Strip wire ends back /" ) Twist ends together C) Solder D) Tape D 3 Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter and making connections as shown. (Isolate and individually tape off the ends of any unused wires to prevent electrical short circuit.) Re-connect the negative battery terminal and test the unit for proper operation. Reassemble radio and dash assemblies in reverse order of disassembly. FINL WIRING CONNECTIONS Make wiring connections using the EI color code chart shown below and the instructions included with the head unit. Metra recommends making connections as shown below; Strip, Splice, Solder, Tape. Isolate and individually tape off ends of any unused wires to prevent electrical short circuit. METR / EI WIRING CODE V Ignition / cc.......... Red Right Front (+)............ Gray V att / Memory......... Yellow Right Front (-)............. Gray/ lack Ground.................. lack* Left Front (+)............. White Power ntenna............ lue Left Front (-).............. White / lack mp Turn-On............. lue / White Right Rear (+)............ Violet mp Ground.............. lack / White Right Rear (-)............. Violet / lack Illumination.............. Orange Left Rear (+)............. Green Dimmer................. Orange / White Left Rear (-).............. Green / lack *NOTE: When a lack wire is not present, ground radio to vehicle chassis. ll colors may not be present on all leads due to manufacturer s specifications. 4
95-734 NOTES 5
95-734 INSTRUCTIONS -800--093 www.metraonline.com REV. 04/7/0 COPYRIGHT 004-0 METR ELECTRONICS CORPORTION INST95-734