INSTALLATION INSTRUCTIONS Accessory Application Publications No. BII 32596 ATTACHMENT 2007 RDX P/N 08L03-STK-100 Issue Date AUG 2006 Put this information in the glove box with the vehicle owner's manual. PARTS LIST 2 Snowboard carriers INSTALLATION NOTE: Be careful not to damage the body paint finish. 1. Rotate the two top clamps of the snowboard carrier perpendicular to the snowboard carrier. 4 Bottom clamps 16 Rubber blocks 4 Torx screws 4 Board supports TOP CLAMPS (Rotate) 2 Keys 2319010K TORX wrench 2 Locking cables 2 Board protectors 2006 American Honda Motor Co., Inc. - All Rights Reserved. BII 32596 (0608) 08L03-SCV-1000-91 1 of 6
2. Install two board supports on the snowboard carrier. 3. Install four rubber blocks on the top and bottom clamps. Install the rubber blocks with the apex of each triangular mark facing the inside. TOP CLAMP SUPPORT (Push.) (Push.) SUPPORT 2321090K MARK (Install the rubber blocks with the apex of this mark facing the inside.) 2319040K MARK (Install the rubber blocks with the apex of this mark facing the inside.) BOTTOM CLAMP 2321080K 2 of 6 BII 32596 (0608) 2006 American Honda Motor Co., Inc. - All Rights Reserved.
4. Turn the cam levers on the top clamp counterclockwise. 7. Attach one carrier to the front cross bar in the direction shown. Insert the barrel nuts on the top clamp into the square holes in the bottom clamp, and turn the nuts 90 to lock them into position. Install the other carrier to the rear cross bar using the same procedure. Make sure the rear cross bar is parallel to the front cross bar. CROSS BAR FRONT TOP CLAMP CAM LEVER (Turn counterclockwise.) CAM LEVER (Turn counterclockwise.) 2319020K BARREL NUT BOTTOM CLAMP 5. Attach the two bottom clamps to the two top clamps. SQUARE HOLE S (Install parallel to each other.) BARREL NUT (Turn 90.) BOTTOM CLAMP TOP CLAMP 2319050K CROSS BAR 2319062K 6. Repeat steps 1 thru 5 to assemble the other carrier. 2006 American Honda Motor Co., Inc. - All Rights Reserved. BII 32596 (0608) 3 of 6
8. Turn the knobs on the top clamp to tighten the front carrier. 10. To prevent theft, install the screws in the holes in the top clamps. TOP CLAMP KNOB SCREW SCREW 2319071K 9. Return the cam levers to the original location (turn clockwise). TORX WRENCH 2320020K 11. Repeat steps 8 thru 10 to tighten the other carrier. 12. Grab the carriers and make sure they are securely installed. CAM LEVER (Return to the original location.) 2320010K 4 of 6 BII 32596 (0608) 2006 American Honda Motor Co., Inc. - All Rights Reserved.
13. Thread the locking cable through the board protector. PROTECTOR 15. After loading the snowboard(s) on the carrier, adjust it (them) with the help of the board supports so that the top edges are level and the boards are as far down in the carrier as possible. To secure the snowboard(s) use the key to open the covers, and insert the locking cable stoppers into the holes in the carrier covers. (To be level.) 2320030K 14. Insert the locking cable plate into the slit in the snowboard carrier. To carry one snowboard, insert the plate into the lowest slit. To carry two snowboards, use one of the upper three slits in the carrier. SUPPORT SLIT (To carry two snowboards) COVER KEY COVER HOLE STOPPER PLATE 2320051K SLIT (To carry one snowboard) 2320040K 2006 American Honda Motor Co., Inc. - All Rights Reserved. BII 32596 (0608) 5 of 6
16. Check that the locking cables are installed securely, then close the covers. 17. The cover must be locked during transportation. Check that the plate is inserted in the slit securely. (Check that the locking cable is inserted in the groove securely.) KEY (Unlocked) (Locked) KEY 2320060K COVER 2320070K 6 of 6 BII 32596 (0608) 2006 American Honda Motor Co., Inc. - All Rights Reserved.