Dial Indicator SERIES 2 Standard Type, 0.01mm Resolution Series 2 dial indicators are Mitutoyo s most popular, and have the widest application. Standard 0.01mm graduation dial gauges having a bezel with an outside diameter of 57mm. All types come with limit markers and a bezel clamp as standard. The bezel clamp and lifting lever (optional) can be attached to either the right or left side. These parts can be easily installed and removed without tools. Secure adhesion between the bezel and crystal as well as the use of an O-ring prevents water or oil penetration. The stem spindle is made of high-strength quench-hardened stainless steel suitable for heavy-duty use. A carbide contact point is used. The grand gear is made of stainless steel with high resistance to wear and deformation. Application of a hard coating on the surface of the crystal makes the gauge highly scratch- and chemical- resistant. (Refer to page IV for details.) 2046S 2046S-09 2046S-60 2047S 2046S 2046S-60 2902S 2310S-10-18
Order No. w/ lug lat-back 2044S 2044SB 2044S-09 2044SB-09 2044S-60 2044SB-60 2045S 2045SB 2046S 2046SB 2046S-09 2046SB-09 2046S-60 2046SB-60 2310S-10 2310SB-10 2902S 2902SB 2047S 2047SB SPECIICATIONS ISO/JIS type Graduation Order No. Range Accuracy Repeatability reading force Dial Measuring w/ lug lat-back (range/rev) Overall Retrace 1/10 Rev 1 Rev 0.01mm 2044S 2044SB 5mm (1mm) ±12µm 5µm 8µm ±10µm 5µm ±0-100 1.4N or less 0.01mm 2044S-09 2044SB-09 5mm (1mm) ±13µm 5µm 8µm ±10µm 5µm ±0-100 1.4N or less 0.01mm 2044S-60 2044SB-60 5mm (1mm) ±12µm 5µm 8µm ±10µm 5µm ±0-100 2.5N or less 0.01mm 2045S 2045SB 5mm (1mm) ±12µm 5µm 8µm ±10µm 5µm 0-50-0 1.4N or less 0.01mm 2046S 2046SB 10mm (1mm) ±13µm 5µm 8µm ±10µm 5µm ±0-100 1.4N or less 0.01mm 2046S-09 2046SB-09 10mm (1mm) ±15µm 5µm 8µm ±10µm 5µm ±0-100 1.4N or less 0.01mm 2046S-60 2046SB-60 10mm (1mm) ±13µm 5µm 8µm ±10µm 5µm ±0-100 2.5N or less 0.01mm 2310S-10 2310SB-10 10mm (1mm) ±15µm 5µm 8µm ±10µm 5µm ±0-100 1.4N or less 0.01mm 2902S 2902SB 10mm (1mm) ±13µm 5µm 8µm ±10µm 5µm 100-0 1.4N or less 0.01mm 2047S 2047SB 10mm (1mm) ±13µm 5µm 8µm ±10µm 5µm 0-50-0 1.4N or less *Use in a vertical position only (contact point downward). Optional Accessories : Backs (See page -40.) : Contact points (See page -36.) DIMENSIONS ISO/JIS Type Unit: mm 2044S 2044S-60 2044S-09 2045S Note 1: Note 2: Dimensions of the inch (ANSI/AGD Type) dial indicator partly differ from those of the metric (ISO/JIS Type) indicator. Inch (ANSI/AGD Type) dial indicator is provided with a stem of 3/8" dia. and #4-48UN thread mount for the contact point. Order No. A B C D E G H I 2044S 48.8 65.2 57 17.7 20 16.9 19.8 52 7.6 2044S-09 48.8 65.2 57 17.7 20 16.9 19.8 52 7.6 2044S-60 48.8 70 57 17.7 20 12.3 29.2 52 7.6 2045S 48.8 65.2 57 17.7 20 16.9 19.8 52 7.6 2046S 48.8 65.2 57 17.7 20 16.9 19.8 52 7.6 2046S-09 48.8 65.2 57 17.7 20 16.9 19.8 52 7.6 2046S-60 48.8 70 57 17.7 20 12.3 29.2 52 7.6 2310S-10 48.8 65.2 57 17.7 20 16.9 19.8 52 7.6 2902S 48.8 65.2 57 17.7 20 16.9 19.8 52 7.6 2047S 48.8 65.2 57 17.7 20 16.9 19.8 52 7.6-19
Dial Indicator SERIES 2 Standard Type, 0.001mm Resolution Standard 0.001mm and 0.005mm graduation dial indicators having a bezel with an outside diameter of ø57mm. All types come with limit markers and a bezel clamp. The outer clamp and lifting lever (optional) can be attached to either the right or left side. These parts can be easily installed and removed without tools. Secure adhesion between the bezel and crystal as well as the use of an O-ring prevents water or oil penetration. The spindle is made of high-strength quench-hardened stainless steel which resists arduous use. A carbide contact point is used. A special alloy is used for the sector gears to provide improved wear resistance. The indicator uses jewelled bearings, providing excellent indication sensitivity and durability. Application of a hard coating on the surface of the crystal makes the gauge highly scratch- and chemical-resistant. (Refer to page IV for details.) 2109S-10 2109S-70 2110S-10 2110S-70 2113S-10 2109S-10 2110S-10 2118S-10 2119S-10 2124S-10 2119S-10-20
Order No. w/ lug lat-back 2109S-10 2109SB-10 2109S-70 2109SB-70 2110S-10 2110SB-10 2110S-70 2110SB-70 2113S-10 2113SB-10 2118S-10 2118SB-10 2119S-10 2119SB-10 2124S-10 2124SB-10 SPECIICATIONS ISO/JIS type Graduation Order No. Range Accuracy Repeatability reading force Dial Measuring w/ lug lat-back (range/rev) Overall Retrace 1/10 Rev 1 Rev 0.001mm 2109S-10 2109SB-10 1mm (0.2mm) ±5µm 3µm 2.5µm ±4µm 0.5µm 0-100-0 1.5N or less 0.001mm 2109S-70 2109SB-70 1mm (0.2mm) ±5µm 3µm 2.5µm ±4µm 0.5µm 0-100-0 2.0N or less 0.001mm 2110S-10 2110SB-10 1mm (0.1mm) ±5µm 3µm 2.5µm ±4µm 0.5µm ±0-100 1.5N or less 0.001mm 2110S-70 2110SB-70 1mm (0.1mm) ±5µm 3µm 2.5µm ±4µm 0.5µm ±0-100 2.0N or less 0.001mm 2113S-10 2113SB-10 2mm (0.2mm) ±7µm 3µm 4µm ±6µm 0.5µm 0-100-0 1.5N or less 0.001mm 2118S-10 2118SB-10 5mm (0.2mm) ±10µm 4µm 5µm ±7µm 1µm 0-100-100 1.5N or less 0.001mm 2119S-10 2119SB-10 5mm (0.2mm) ±10µm 4µm 5µm ±7µm 1µm 0-100-0 1.5N or less 0.005mm 2124S-10 2124SB-10 5mm (0.5mm) ±12µm 5µm 7µm ±9µm 3µm ±0-50 1.5N or less Optional Accessories : Backs (See page -40.) : Contact points (See page -36.) DIMENSIONS ISO/JIS Type Unit: mm Note 1: Note 2: Dimensions of the inch (ANSI/AGD Type) dial indicator partly differ from those of the metric (ISO/JIS Type) indicator. Inch (ANSI/AGD Type) dial indicator is provided with a stem of 3/8" dia. and #4-48UN thread mount for the contact point. Order No. A B C D E G H I 2109S-10 48.8 60.5 57 17.7 20 16.9 15.1 52 7.6 2109S-70 48.8 65.3 57 17.7 20 12.3 24.5 52 7.6 2110S-10 48.8 66.5 57 17.7 20 16.9 21.1 52 7.6 2110S-70 48.8 67.5 57 17.7 20 12.3 26.7 52 7.6 2113S-10 48.8 61 57 17.7 20 16.9 15.6 52 7.6 2118S-10 48.8 60.3 57 17.7 20 16.9 14.9 52 7.6 2119S-10 48.8 60.3 57 17.7 20 16.9 14.9 52 7.6 2124S-10 48.8 60.3 57 17.7 20 16.9 14.9 52 7.6-21
Dial Indicator SERIES 2 Standard Type, Inch Reading SPECIICATIONS Inch ANSI/AGD type Graduation Order No. Range Accuracy Repeatability reading force Dial Measuring w/ lug lat-back (range/rev) irst 1 Rev / 2.5 Rev / 10 Rev Retrace.001 2414S 2414SB.5 (.1 ) ±.001 / ±.001 / ±.001.0002 ±.0002 ±0-100 1.8N or less.001 2415S 2415SB.5 (.1 ) ±.001 / ±.001 / ±.001.0002 ±.0002 0-50-0 1.8N or less.001 2914S 2914SB.5 (.1 ) ±.001 / ±.001 / ±.001.0002 ±.0002 100-0 1.8N or less.0005 2506S 2506SB.125 (.05 ) ±.0005 / ±.0005 /.00016 ±.0001 ±0-50 1.8N or less.0005 2507S 2507SB.125 (.05 ) ±.0005 / ±.0005 /.00016 ±.0001 0-25-0 1.8N or less.0005 2514S 2514SB.5 (.05 ) ±.0005 / ±.0005 / ±.0015.00016 ±.0001 ±0-50 1.8N or less.0005 2922S 2922SB.125 (.05 ) ±.0005 / ±.0005 /.00016 ±.0001 0-25-0 1.8N or less.0001 2356S-10 2356SB-10.25 (.01 ) ±.0002 / ±.0002 / ±.0003.0001 ±.00003 0-10 2.0N or less ±.0004 (irst 20rev) / ±.0005 (Over 20rev).0001 2358S-10 2358SB-10.5 (.01 ) ±.0002 / ±.0002 / ±.0003.00015 ±.00003 0-10 2.0N or less ±.0004 (irst 20rev) / ±.0005 (Over 20rev).0001 2802S-10 2802SB-10.025 (.01 ) ±.0001 / ±.0001 /.0001 ±.00003 0-10 2.0N or less.0001 2803S-10 2803SB-10.025 (.01 ) ±.0001 / ±.0001 /.0001 ±.00003 0-5-0 2.0N or less.0001 2804S-10 2804SB-10.05 (.01 ) ±.0001 / ±.0001 / ±.0002.0001 ±.00003 0-10 2.0N or less.0001 2805S-10 2805SB-10.05 (.01 ) ±.0001 / ±.0001 / ±.0002.0001 ±.00003 0-5-0 2.0N or less.0001 2905S-10 2905SB-10.05 (.01 ) ±.0001 / ±.0001 / ±.0002.0001 ±.00003 10-0 2.0N or less.0001 2923S-10 2923SB-10.05 (.01 ) ±.0001 / ±.0001 / ±.0002.0001 ±.00003 0-5-0 2.0N or less Inch Order No. w/ lug lat-back 2414S 2414SB 2415S 2415SB 2914S 2914SB 2506S 2506SB 2507S 2507SB 2514S 2514SB 2922S 2922SB 2356S-10 2356SB-10 2358S-10 2358SB-10 2802S-10 2802SB-10 2803S-10 2803SB-10 2804S-10 2804SB-10 2805S-10 2805SB-10 2905S-10 2905SB-10 2923S-10 2923SB-10 (Refer to page IV for details.) Optional Accessories : Backs (See page -40.) : Contact points (See page -36.) -22
DIMENSIONS ANSI/AGD Type Unit: mm Order No. A B C D E G H I 2414S 38.9 64.1 57 17.7 19 13.6 22 52 7.6 2415S 38.9 64.1 57 17.7 19 13.6 22 52 7.6 2914S 38.9 64.1 57 17.7 19 13.6 22 52 7.6 2506S 48.8 54.3 57 17.7 19 13.6 12.2 52 7.6 2507S 48.8 54.3 57 17.7 19 13.6 12.2 52 7.6 2514S 38.9 64.1 57 17.7 19 13.6 22 52 7.6 2922S 48.8 54.3 57 17.7 19 13.6 12.2 52 7.6 2356S-10 48.8 57.2 57 17.7 19 13.6 15.1 52 7.6 2358S-10 38.9 63.6 57 17.7 19 13.6 21.5 52 7.6 2802S-10 48.8 51.4 57 17.7 19 13.6 9.3 52 7.6 2803S-10 48.8 51.4 57 17.7 19 13.6 9.3 52 7.6 2804S-10 48.8 51.7 57 17.7 19 13.6 9.6 52 7.6 2805S-10 48.8 51.7 57 17.7 19 13.6 9.6 52 7.6 2905S-10 48.8 51.7 57 17.7 19 13.6 9.6 52 7.6 2923S-10 48.8 51.7 57 17.7 19 13.6 9.6 52 7.6-23