Troubleshooting TO PREVENT INJURYTOYOURSELF or damage to the Air Filtration System, turn the switch to the machine "OFF" and unplug the power cord from the electrical receptacle before making any adjustments. PROBLEM LIKELY CAUSE(S) SOLUTION(S) Motor does not run 1. Machine not plugged in 1. Plug power cord into electrical receptacle 2. Power switch in "OFF" position 2. Lift switch to "ON" postion 3. Power switch or cord is faulty 3. Replace switch or po wer cord 4. Fuse or circuit breaker are open 4. Overloaded electrical circu it 5. Remote control is not working 5. Point remote control directly at control panel - Make sure infared sensor on the control panel is not blocked -Move remote control closer to the control panel for better direct infared signal 6. Remote control batteries are dead 6. Replace batteries. See page 13 for instruction 7. lnfared receiver is not working?.inspect or replace control panel circuit board 8. Control panel ON/OFF button is B. Inspect or replace control panel circuit board not working 9. Control panel fuse is blown 9. Rep lace blown fuse, see page 13 for instruction 10. Motor does not work 10. Replace motor Motor stalls 1.1ncorrect line voltage 1. Have a qualified electrican check circuit for or does not 2. Motor capacitor has failed proper voltage have full 2. Replace motor capacitor power 3. Control panel circuit board has 3. Inspect or replace control panel circuit board failed 1. Motor or cabinet part is loose 1. Inspect all hardware and retighten or replace 2. Motor fan is rubbing cover 2. Check position of fan and cover Adjust or replace loose/damaged part 3. Motor bearings are loud 3. Rotate motor shaft to isolate the issue System has Replace worn bearings vibration or is 4. Air filters rattle 4. Inspect and reposition filters noisy 5. 1mpeller fan is loose, unbalanced or 5. Turn machine off and unplug from power. damaged -Inspect impeller for bent or damaged areas. -Secure impeller on motor shaft and replace if any damage is found 6. Motor base is loose in the cabinet 6. Tighten any loose fasteners Poor air flow 1. Filters are dirty 1. Clean or replace both air filters frequently. See and dust page 12 collection 2. Poor system location in shop 2. Reposition system in the shop for best air circulation. Refer page 9 for proper air filtration system placement 14
Wiring Diagram WARNING:This machine must be grounded. Replacement of the power supply cable should only be done by a qualified electrician. White Black - ""T1 t: -o- CD ~ 0 en... 1\) )> G) White (il CD ::::J 1\) 0 '1J 01 m 0 < 'I-'..., "' ' 1-' -..._,...,.-..._,... I ""0 ~.., CD n 0 G) a t: ::::::J c..... -111 0 -......, G) 0 0 ""T1 0 (il CD ::::J "' r4v =...I.. G) CiJ CD ::::J ""T1 z 1\JS:: oo <c;...lo..., )> -----1 - li' :;:, '1J ::I: - 0 c: c: 1 CJ) ~ - ~ :::::J (Q - llj llj t: I» ~ CD n D.. "' Capicitor 15
62-400 AIR FILTRATION SYSTEM CEILING MOUNTING HARDWARE PACK 7 CONTROL PANEL I ASSEMBLY REMOTE CONTROL UNIT CONTROL PANEL ASSEMBLY MOTOR & FAN ASSEMBLY
Key No. Description QTY MFG. PART NO. Key No. Description QTY MFG. PART NO. 1 Hex Nut 4mm 9 P62-400-1 38 Phillips Head Screw M5X20 1 P62-400-38 2 Flat Washer 4mm 10 P62-400-2 39 Fuse Holder 1 P62-400-39 3 Lock Washer 4mm 9 P62-400-3 40 Fuse Cap 1 P62-400-40 4 Phillips Head Screw M4X12 5 P62-400-4 41 Fuse (2A) 1 P62-400-41 5 Phillips Head Screw M6X16 6 P62-400-5 42 Control Panel Label 1 P62-400-42 6 Cabinet Back Cover 1 P62-400-6 43 Phillips Head Screw M3X15 1 P62-400-43 7 Wire Mesh 1 P62-400-7 44 Phillips Head Screw M3X30 1 P62-400-44 8 Air Guide 1 P62-400-8 45 Phillips Head Tapping Screw ST3.2X8 1 P62-400-45 9 Phillips Head Hex Nut 6mm 6 P62-400-9 46 Printed Circuit Board 1 P62-400-46 10 Flat Washer 6mm 6 P62-400-10 47 Switch Box 1 P62-400-47 11 Lock Washer 6mm 6 P62-400-11 48 Flat Washer 3mm 1 P62-400-48 12 Phillips Head Screw M4X12 8 P62-400-12 49 Lock Washer 3mm 1 P62-400-49 13 Phillips Head Tapping Screw ST4X10 34 P62-400-13 50 Hex Nut 3mm 1 P62-400-50 14 Cabinet 1 P62-400-14 51 Wire 1 P62-400-51 15 Phillips Head Screw M6X12 4 P62-400-15 52 Impeller/Fan Wheel 1 P62-400-52 16 Carrying Handle 1 P62-400-16 53 Fan Housing Cover 1 P62-400-53 17 Handle Bracket 1 P62-400-17 54 Fan Housing 1 P62-400-54 18 Phillips Head Screw M5X16 2 P62-400-18 55 Rubber Spacer 4 P62-400-55 19 Flat Washer 5mm 3 P62-400-19 56 Large Washer 5mm 4 P62-400-56...>. 20 Lock Washer 5mm 3 P62-400-20 57 Lock Nut 5mm 4 P62-400-57 ""-- 21 Hex Nut 5mm 4 P62-400-21 58 Motor 1 P62-400-58 22 Phillips Head Screw M5X12 1 P62-400-22 59 Capacitor Cover 1 P62-400-59 23 Lock Washer 5mm 1 P62-400-23 60 Capacitor 1 P62-400-60 24 Grounding Wire 1 P62-400-24 61 Fan Housing Cover 1 P62-400-61 25 Wire Mesh 1 P62-400-25 62 Phillips Head Screw M5X25 4 P62-400-62 26 Inner Filter 1 P62-400-26 63 Machine Hook 4 P62-400-63 27 Outer Filter 1 P62-400-27 64 Flange Nut 6mm 4 P62-400-64 28 Rubber Foot 4 P62-400-28 65 Chain 4 P62-400-65 29 Remote Control Unit 1 P62-400-29 69 Switch Box Cover 1 P62-400-69 30 Power Cord 1 P62-400-36 72 Wood Screw Hook 4 P62-400-72 31 Strain Relief 1 P62-400-37 NOTE: Please reference the Manufacturers Part Number when calling for replacement parts.
Warranty POWER TOOLS To take advantage of tliis warranty proof of purchase aocumentation, which includes date of purchase and an explanation of the complaint, must be provided. To take advantage of this warranty, please fill out the enclosed warranty card and send it to: RIKON Warranty 16 Progress Rd. Billerica, MA 01821 The card must be entirely completed in order for it to be valid. If you have any questions please contact us at 877-884-5167 or warranty@rikontools.com. 18
Accessories 62-901 F Outer Filter 62-902F Inner Filter Notes Use this section to record maintenance, service and any calls to Technical Support. 19