Sylvania 7.5' Pre-Lit Troy Fir Tree LED Color Changing and Multi Function One Plug Tree Tree ID #T1, Item # V67656-13 Thank you for purchasing this tree. This tree assembles in minutes and is decorated with 500 LED lights. For your convenience, it is equipped with a foot pedal switch for easy illumination and changing functions. For Indoor/Seasonal Use Only. This tree has been carefully constructed to insure many years of safe, seasonal use. In the unlikely event that you experience problems with the tree or need assistance in assembly, Do not return this tree to the place of purchase. Please call our customer service hotline at (800) 681-3839. Agents are on call 24/7 to answer your questions. If you prefer you may contact us via email at athometrees@inliten.com. If you do need assistance, please provide us with the 2 digit Tree ID number from the original carton or the 7 digit item number of the product purchased (located below the UPC code) as well as information pertaining to the nature and description of the problem. If you no longer have the original carton of this tree, the tree can also be identified by the 12 digit Garden Ridge UPC code. The UPC code can be located on the sticker on the pole of the bottom section of tree right above where the trunk enters the tree stand. Please do not remove this identification sticker. This 7.5 ft tree is pre lit with 500 Color Changing LED Lights: CARTON INCLUDES: 3 pre-lighted tree sections (A Top Section, B Middle Section, C Bottom Section) 1 sturdy metal tree stand 1 screw for tree stand 8 extra LED replacement bulbs 1 Remote control 1 foot pedal switch 1 adaptor
ASSEMBLY: Note: Before you start to assemble your tree, please choose a location near an electrical wall outlet. Place the tree stand on a level surface. Please remove protective covers from the base of the pole from each section. 1. Unfold the tree base and insert the screw into the hole. 2. Carefully insert bottom section (C) of tree into tree base and tighten the screw. (See Fig. 1) 3. Insert the middle section (B) of the tree into the bottom section (C). Rotate the middle section (B) right or left until it falls into place, then insert vertically and tightly into the bottom section (C) to ensure proper circuit connection. (See Fig. 2) 4. Insert the top section (A) into the middle section (B). Rotate the top section (A) right or left until it falls into place, then insert vertically and tightly into the middle section (B) to ensure proper circuit connection. (See Fig. 3) 5. Insert the provided foot pedal switch and adaptor separately into the tree bottom (C) according to the magnified drawing (See Fig. 4). 6. Allow the branches to fall into place or gently pull branches up and out. When adjusting branches be sure that all wires are free of branch hinges. (See Fig. 5) 7. Shape the branches. Starting with tips closest to the pole, shape one tip to the right, one to the left and one along the centre of the main stem. Repeat pattern for each branch. (See Fig. 6) 8. Plug the well-connected adaptor into electric outlet (See Fig. 7). Please note this tree comes with a foot pedal switch and a remote control for easy illumination and changing functions. This tree is Color Changing, the 8 lighting options available are, Steady Warm white, Warm white Rippling, Steady Multi, Multi Rippling, Color Changing, Warm white Cascade then Multi Cascade, Color changing Cascade and Magician. These functions can be changed by using the foot pedal switch or via the remote control. Please see the instructions of remote control below.
INSTRUCTIONS OF REMOTE CONTROL Please note this tree has a remote control. Please pull out the insulation tape from the remote control, before starting to use it. 1. The first button is for the on/off power switch for the lights and the second button is for choosing different functions. 2. Press Fn button. Select from the following lighting functions: Function 1: Steady Warm white Function 2: Warm white rippling Function 3: Steady Multi Function 4: Multi rippling Function 5: Color changing Function 6: Warm white cascade then multi cascade Function 7: Color changing cascade Function 8: Magician If the remote control does not work, check whether the battery of the remote control is out of power. To replace the remote control battery: 1. Use Phillips screwdriver to open the back cover of the remote control. 2. Replace with a new alkaline A23 (12 volt) battery into the compartment. WARNING: This is not a toy and is not intended for use by children. (A) Do not dispose of the battery in fire as the battery may leak and explode. (B) Do not mix old and new batteries and do not mix alkaline, standard (carbon-zinc), or rechargeable (nickel-cadmium) batteries. (C) Always purchase the correct size and grade of battery most suitable for the intended use. (D) Replace all batteries of a set at the same time. (E) Clean the battery contacts and also those of the device prior to battery installation. (F) Ensure the batteries are installed correctly with regard to polarity (+ and -). (G) Remove batteries from equipment which is not to be used for an extended period of time. (H) Remove used batteries promptly. (I) Exhausted batteries are to be removed from the product. (J) Use type A23 (12 volt) batteries. USE AND CARE INSTRUCTIONS a) Before using or reusing, inspect product carefully. Discard any products that have cut, damaged, or frayed wire insulation or cords, cracks in the lamp holders or enclosures, loose connections, or exposed copper wire.
b) When storing the product, carefully remove the product from wherever it is placed to avoid any undue strain or stress on the product conductors, connections, and wires. c) When not in use, store neatly in a cool, dry location protected from sunlight. USER SERVICING INSTRUCTIONS BULB REPLACEMENT: 1. Grasp plug and remove from its power source. 2. Remove the reflector from the bulb. (See Fig. 1) Fig. 1 Fig. 2 Fig. 3 Fig. 4 Fig. 5 3. Pull bulb straight out of socket. Do not twist bulbs. (See Fig. 2) 4. Replace burned-out bulb with 3.0 V, 0.06 W LED bulb ONLY. Directly insert the LED bulb into the bulb holder. (Additional bulbs are included for your convenience.) (See Fig. 3) 5. If the bulb still does not light, change the LED bulb s direction in the bulb holder. (See Fig. 4) 6. Replace the reflector on the LED bulb. (See Fig.5) IMPORTANT SAFETY INSTRUCTIONS a. READ AND FOLLOW ALL SAFETY INSTRUCTIONS b. Do not use seasonal products outdoors unless marked suitable for indoor and outdoor use. When products are used in outdoor applications, connect the product to a Ground Fault Circuit Interrupting (GFCI) outlet. If one is not provided, contact a qualified electrician for proper installation. c. This seasonal use product is not intended for permanent installation or use. d. Do not mount or place near gas or electric heaters, fireplaces, candles or other similar sources of heat. e. Do not secure the wiring of the product with staples or nails, or place on sharp hooks or nails. f. Do not let lamps rest on the supply cord or on any wire. g. Unplug the product when leaving the house, or when retiring for the night, or if left unattended. h. This is an electric product not a toy! To avoid risk of fire, burns, personal injury and electric shock it should not be played with or placed where small children can reach it. i. Do not use this product for other than its intended use. j. Do not hang ornaments or other objects from cord, wire, or light string. k. Do not close doors or windows on the product or extension cords as this may damage the wire insulation. l. Do not cover the product with cloth, paper or any material not part of the product when in use. m. This product is equipped with push-in type lamps. Do not twist lamps. n. Read and follow all instructions that are on the product or provided with the product. o. SAVE THESE INSTRUCTIONS TROUBLESHOOTING If any lights do not work on your pre-lighted tree, please check the following: 1. If entire tree or a section of the tree does not light: a) Check that each section of the tree is well connected. b) Make sure the adaptor plug is securely inserted into a working electrical outlet.
c) Make sure the foot pedal switch and adaptor are well connected to the bottom section (C). 2. If a strand of lights still does not work: a) Check that all bulbs are tightly fitted inside the sockets and that no bulbs are broken or missing. Replace any broken or missing bulbs with replacements bulbs provided (see Bulb Replacement below). This product carries a one year limited warranty. This warranty does not cover damage resulting from accident, misuse, abuse, negligence, or normal wear and any discoloration. The warranty is in force from the date that you purchased this tree. There is no need to register your purchase, however it is most important that you retain your At Home sales receipt as proof of purchase. Receipt may be required for warranty service. Please note this warranty is non-transferable and is voided if the product is not used as intended. Please keep this product manual for future reference. STORAGE: Disassembled tree can be stored in its original box. Store tree in a cool dry place where the temperature does not exceed 100 degrees Fahrenheit.