INSTALL GUIDE DOCUMENT NUMBER 54456 REVISION DATE 01818 FIRMWARE OL-FO(RS)-FO1B-[OL-RS-FO1] HARDWARE OL-RS-FO1 ACCESSORIES OL-LOADER (REQUIRED) RF-/30/50-EDP (OPTIONAL) LINKR (OPTIONAL) TERMS OF USE: Automotive Data Solutions Inc. ( ADS ) products are strictly intended for installation by Certified Technicians who are employed by a registered business specialized in the installation of automotive aftermarket electronics products. Prior to beginning installation of an ADS product in a vehicle, it is the Certified Technician s responsibility to review the most current Product Guide, Install Guide and vehicle-specific notes available in Weblink. ADS is not responsible for any damages whatsoever, including but not limited to any consequential damages, incidental damages, damages for loss of time, loss of earnings, loss of profit, commercial loss, loss of economic opportunity and the like that may or may not have resulted from the use, misuse, improper installation or operation of its products. ADS reserves itself the right to suspend any Weblink account without notice and decline to offer technical support to non-certified Technicians, non-compliant Certified Technicians or end users. BEFORE INSTALLATION 1- Connect module to computer - Login to Weblink account 3- Flash firmware to module (module is not preloaded with firmware) 4- Use accessories accordingly (accessories are sold separately)
VEHICLE LIST - 1 OF 1 PAGE OF 5 FEATURES MAKE MODEL YEAR INSTALL TYPE DATA IMMOBILIZER BYPASS 3X LOCK /STANDALONE MOD. DOOR LOCK DOOR UNLOCK FORD ARM OEM ALARM LINCOLN DISARM OEM ALARM POWER LIFTGATE TRUNK/HATCH RELEASE RAP SHUTDOWN CTRL HOOD STATUS (W/OEM SW) DOOR STATUS BRAKE PEDAL STATUS TACHOMETER STATUS GLOW PLUGS STATUS PARKING LIGHT CTRL Edge STD key AT 11-14 1 Expedition STD key AT 15-17 Explorer STD key AT 11-15 1 F-150 STD key AT 11-14 F-Super Duty STD key AT 11-16 Fiesta STD key AT 14-18 3 Flex STD key AT 13-15 Taurus STD key AT 13-17 Transit STD key AT* 15-18 4 MKX STD key AT 11-1 1 *Aftermarket RF kit required to control remote start.
BOX CONTENTS - 1 OF 1 PAGE 3 OF 5 BOX CONTENTS MODULE T-HARNESS 1 PIN VS BLUE BLACK BLACK 1 4 3 6 5 1 4 3 6 5 8 7 9 1 11 14 13 16 15 18 17 0 19 1 4 3 6 5 8 7 9 1 11 M1 M M3 LED LED 1 M7 M6 M5 M4 PROGRAMMING BUTTON 4 3 1 4 3 1 3 1 9 7 8 5 6 3 4 1 BLACK RF PORT/ WEBLINK PORT BLUE TELEMATIC PORT BLACK WHITE MS MS1 VS1 VS4 VS3 1 PIN AFTERMARKET HOOD SWITCH AND CABLE WARNING STICKER WEBLINK CABLE (required accessory sold separately) WEBLINK CABLE MODULE WEBLINK PORT COMPUTER USB PORT 4 PIN BLACK CABLE
COMPATIBLE ACCESSORIES - 1 OF 1 PAGE 4 OF 5 DOC.: #54456 01818 RF KIT (accessories sold separately) OMEGA RF KIT MODULE RF PORT (NC) ANTENNA TELEMATIC KIT (accessories sold separately) OLCLLINK CARLINK MODULE TELEMATIC PORT (NC) TELEMATIC KIT (accessories sold separately) LINKR MODULE TELEMATIC PORT (NC)
COMPONENT LOCATOR - 1 OF 1 PAGE 5 OF 5 INTERIOR VIEW C F A B G H D E DRIVER SIDE VIEW PASSENGER SIDE VIEW
TYPE 1 - WIRE CHART - 1 OF 1 PAGE 6 OF 5 FORD MAKE MODEL YEAR WIRE DESCRIPTION NAME COLOR TYPE POSITION WIRE COLOR LINCOLN POLARITY MODULE LOCATION COMPONENT LOCATOR Edge STD key AT Explorer STD key AT MKX STD key AT 11-14 11-15 11-1 CanH C51 Black 16 pin Gray/Orange (DATA) OBDII connector G CanL C51 Black 16 pin 11 Purple/Orange (DATA) OBDII connector G Horn C80B Black 5 pin 33 Purple/Green (-) BCM, driver side dash H Driver Door Pin C80C Black 6 pin Green/Purple (OPEN) BCM, driver side dash H Lock C80C Black 6 pin Blue/Green (-) BCM, driver side dash H Unlock C80C Black 6 pin 08 Yellow/Purple (-) BCM, driver side dash H Trunk Release C69 Black pin Gray/Yellow (-) At liftgate switch in glovebox D Parking Light C80E Gray pin Yellow/Blue (+) BCM, driver side dash H CanH C51 Black 16 pin Gray/Orange (DATA) OBDII connector G CanL C51 Black 16 pin 11 Purple/Orange (DATA) OBDII connector G Horn C80B Black 5 pin 33 Purple/Green (-) BCM, driver side dash H Driver Door Pin C80C Black 6 pin Green/Purple (OPEN) BCM, driver side dash H Lock C80C Black 6 pin Blue/Green (-) BCM, driver side dash H Unlock C80C Black 6 pin 08 Yellow/Purple (-) BCM, driver side dash H Trunk Release C114 Black 08 pin Gray/Yellow (-) At liftgate switch on driver side dash A Parking Light C80E Gray pin Yellow/Blue (+) BCM, driver side dash H CanH C51 Black 16 pin Gray/Orange (DATA) OBDII connector G CanL C51 Black 16 pin 11 Purple/Orange (DATA) OBDII connector G Horn C80B Black 5 pin 33 Purple/Green (-) BCM, driver side dash H Driver Door Pin C80C Black 6 pin Green/Purple (OPEN) BCM, driver side dash H Lock C80C Black 6 pin Blue/Green (-) BCM, driver side dash H Unlock C80C Black 6 pin 08 Yellow/Purple (-) BCM, driver side dash H Trunk Release C69 Black pin Gray/Yellow (-) At liftgate switch in glovebox D Parking Light C80E Gray pin Yellow/Blue (+) BCM, driver side dash H
TYPE 1 - WIRING DIAGRAM - 1 OF 1 PAGE 7 OF 5 VS IGNITION SWITCH (UNDER STEERING COLUMN) M1 M M3 M6 RF PORT/WEBLINK PORT M6 TELEMATIC PORT M5 M4 VS1 1 : IMMOBILIZER 1 : IMMOBILIZER HARNESS M1 M 01 01 08 11 1 13 14 15 16 17 18 19 0 MS MS1 M3 01 BROWN/BLACK - PARKING LIGHT (-) OUTPUT GRAY (NC) PURPLE/GREEN - LOCK (-) OUTPUT 08 BLUE/GREEN - TRUNK (-) OUTPUT 11 GRAY/GREEN - HORN (-) OUTPUT 1 DKGREEN/GREEN - UNLOCK (-) OUTPUT M4 01 GRAY/BLACK (NC) GRAY/WHITE - HOOD STATUS (-) INPUT 08 BROWN/RED BROWN/YELLOW GREEN/WHITE GREEN/PURPLE 87 86 87A 85 30 A VS4 VS3 CANH - CANL - 11 PARKING LIGHT (+) - 1V (+) LOCK (-) - UNLOCK (-) - 08 DRIVER DOOR PIN (OPEN) - HORN (-) - 33 1 OPTIONAL 1 TRUNK RELEASE (-) SEE WIRE CHART : IGNITION E C B 1 3 4 5 6 7 8 9 : IGNITION HARNESS 1 3 4 5 6 7 8 9 11 1 13 14 15 16 1 3 4 5 6 7 8 9 11 1 13 14 15 16 17 18 19 0 1 3 4 5 6 13 1 11 9 8 7 6 5 4 3 1 6 5 4 3 1 0 19 18 17 16 15 14 39 38 37 36 35 34 33 3 31 30 9 8 7 5 51 50 49 48 47 46 45 44 43 4 41 40 1 3 4 5 6 7 8 OR C69 - BLACK 1 OBDII BCM C E B LIFTGATE SWITCH HOOD SWITCH 3 1 3 4 5 6 INSTALL THE SUPPLIED HOOD SWITCH IF THE VEHICLE IS NOT EQUIPPED WITH ONE. 3
TYPE - WIRE CHART - 1 OF PAGE 8 OF 5 MAKE MODEL YEAR FORD WIRE DESCRIPTION NAME COLOR TYPE POSITION WIRE COLOR POLARITY MODULE LOCATION COMPONENT LOCATOR CanH C51 Black 16 pin Gray/Orange (DATA) OBDII connector G CanL C51 Black 16 pin 11 Purple/Orange (DATA) OBDII connector G Horn C80B Black 5 pin 33 Purple (-) BCM, passenger kick panel E Driver Door Pin C80C Black 6 pin Green/Purple (OPEN) BCM, passenger kick panel E Expedition Lock C80C Black 6 pin White/Brown (-) BCM, passenger kick panel E 15-17 STD key AT Unlock C80C Black 6 pin 08 Blue/Brown (-) BCM, passenger kick panel E Trunk Release ~ Black 08 pin Gray/Yellow (-) At liftgate switch C Parking Light C80E Gray pin Yellow/Blue (+) BCM, passenger kick panel E Auto Light C Gray pin Purple/Green (OPEN) Headlight switch A Light Off C Gray pin White/Purple (-) Headlight switch A CanH C51 Black 16 pin Gray/Orange (DATA) OBDII connector G CanL C51 Black 16 pin 11 Purple/Orange (DATA) OBDII connector G Horn C80B Black 5 pin 33 Purple/Green (-) BCM, passenger side dash E Driver Door Pin C80C Black 6 pin Green/Purple (OPEN) BCM, passenger side dash* E F-150 Lock C80C Black 6 pin Blue/Green (-) BCM, passenger side dash* E 11-14 STD key AT Unlock C80C Black 6 pin 08 Yellow/Purple (-) BCM, passenger side dash* E Trunk Release ~ ~ ~ ~ ~ ~ ~ ~ Parking Light C80E Gray pin Yellow/Blue (+) BCM, passenger side dash E Auto Light C Gray pin Purple/Green (OPEN) Headlight switch A Light Off C Gray pin White/Purple (-) Headlight switch A CanH C51 Black 16 pin Gray/Orange (DATA) OBDII connector G CanL C51 Black 16 pin 11 Purple/Orange (DATA) OBDII connector G Horn C80B Black 5 pin 33 Purple/Green (-) BCM, passenger side dash E Driver Door Pin C80C Black 6 pin Green/Purple (OPEN) BCM, passenger side dash* E F-Super Duty Lock C80C Black 6 pin Blue/Green (-) BCM, passenger side dash* E 11-16 STD key AT Unlock C80C Black 6 pin 08 Yellow/Purple (-) BCM, passenger side dash* E Trunk Release ~ ~ ~ ~ ~ ~ ~ ~ Parking Light C80E Gray pin Yellow/Blue (+) BCM, passenger side dash E Auto Light C Gray pin Purple/Green (OPEN) Headlight switch A Light Off C Gray pin White/Purple (-) Headlight switch A * Wire also found in driver door harness.
TYPE - WIRE CHART - OF PAGE 9 OF 5 MAKE MODEL YEAR WIRE DESCRIPTION NAME COLOR TYPE FORD POSITION WIRE COLOR POLARITY MODULE LOCATION COMPONENT LOCATOR Flex STD key AT Taurus STD key AT 13-15 13-17 CanH C51 Black 16 pin Gray/Orange (DATA) OBDII connector G CanL C51 Black 16 pin 11 Purple/Orange (DATA) OBDII connector G Horn C80B Black 5 pin 33 Purple/Green (-) BCM, driver side dash B Driver Door Pin C80C Black 6 pin Purple (OPEN) BCM, driver side dash B Lock C80C Black 6 pin Blue (-) BCM, driver side dash B Unlock C80C Black 6 pin 08 Yellow (-) BCM, driver side dash B Trunk Release C69 Black pin Gray (-) At liftgate switch on driver side dash A Parking Light C80E Gray pin Yellow/Blue (+) BCM, driver side dash B Auto Light C Gray pin Purple/Green (OPEN) Headlight switch A Light Off C Gray pin White/Purple (-) Headlight switch A CanH C51 Black 16 pin Gray/Orange (DATA) OBDII connector G CanL C51 Black 16 pin 11 Purple/Orange (DATA) OBDII connector G Horn C80B Black 5 pin 33 Purple/Green (-) BCM, driver side dash B Driver Door Pin C80C Black 6 pin Green/Purple (OPEN) BCM, driver side dash B Lock C80C Black 6 pin Blue/Green (-) BCM, driver side dash B Unlock C80C Black 6 pin 08 Yellow/Purple (-) BCM, driver side dash B Trunk Release C69 Black pin Brown (-) At trunk release switch on center console C Parking Light C80E Gray pin Yellow/Blue (+) BCM, driver side dash B Auto Light C Gray pin Purple/Green or Purple (OPEN) Headlight switch A Light Off C Gray pin White/Purple or White (-) Headlight switch A
TYPE - WIRING DIAGRAM - 1 OF 1 PAGE OF 5 VS IGNITION SWITCH (UNDER STEERING COLUMN) M1 M M3 M6 RF PORT/WEBLINK PORT M6 TELEMATIC PORT M5 M4 VS1 1 : IMMOBILIZER 1 : IMMOBILIZER HARNESS M1 M 01 01 08 11 1 13 14 15 16 17 18 19 0 MS MS1 M3 01 BROWN/BLACK - PARKING LIGHT (-) OUTPUT GRAY (NC) PURPLE/GREEN - LOCK (-) OUTPUT 08 BLUE/GREEN - TRUNK (-) OUTPUT 11 GRAY/GREEN - HORN (-) OUTPUT 1 DKGREEN/GREEN - UNLOCK (-) OUTPUT M4 01 GRAY/BLACK (NC) GRAY/WHITE - HOOD STATUS (-) INPUT 08 OR 87 86 87A 85 86 87A 85 30 87 86 87A 85 30 BROWN/RED BROWN/YELLOW GREEN/WHITE GREEN/PURPLE 30 87 A A VS4 VS3 CANH - CANL - 11 WITH AUTO LIGHT 1V (+) LIGHT (-) - AUTO LIGHT (OPEN) - PARKING LIGHT (+) - WITHOUT AUTO LIGHT PARKING LIGHT (+) - 1V (+) LOCK (-) - UNLOCK (-) - 08 DRIVER DOOR PIN (OPEN) - HORN (-) - 33 1 OPTIONAL 1 : IGNITION E C B 1 3 4 5 6 7 8 9 : IGNITION HARNESS 1 3 4 5 6 7 8 9 11 1 13 14 15 16 1 3 4 5 6 7 8 9 1 3 4 5 6 7 8 9 11 1 13 14 15 16 17 18 19 0 1 3 4 5 6 13 1 11 9 8 7 6 5 4 3 1 6 5 4 3 1 0 19 18 17 16 15 14 39 38 37 36 35 34 33 3 31 30 9 8 7 5 51 50 49 48 47 46 45 44 43 4 41 40 C 1 E B OBDII PARKING LIGHT SWITCH BCM LIFTGATE SWITCH TRUNK RELEASE (-) C69 - BLACK SEE WIRE CHART HOOD SWITCH 3 1 3 4 5 6 INSTALL THE SUPPLIED HOOD SWITCH IF THE VEHICLE IS NOT EQUIPPED WITH ONE. 3
TYPE 3 - WIRE CHART - 1 OF 1 PAGE 11 OF 5 MAKE MODEL YEAR WIRE DESCRIPTION FORD NAME COLOR TYPE POSITION WIRE COLOR POLARITY MODULE LOCATION COMPONENT LOCATOR CanH C51 Black 16 pin Gray/Orange (DATA) OBDII connector B CanL C51 Black 16 pin 11 Purple/Orange (DATA) OBDII connector B Driver Door Pin C80G Gray 4 pin 19 Green/Purple (OPEN) BCM, behind glove box D Fiesta STD key AT 14-18 Horn C80E Green 4 pin 01 Brown (-) BCM, behind glove box D Light C Gray pin White/Purple (-) Headlight switch A Lock C80F White 4 pin 0 Brown/White (-) BCM, behind glove box D Parking Light C Gray pin Yellow/Blue (-) Headlight switch A Trunk Release C80G Gray 4 pin Green/White (-) BCM, behind glove box D Unlock C80G Gray 4 pin 08 Blue/Brown (-) BCM, behind glove box D Disarm C80G Gray 4 pin Purple/Brown (-) BCM, behind glove box D
TYPE 3 - WIRING DIAGRAM - 1 OF 1 PAGE 1 OF 5 VS IGNITION SWITCH (UNDER STEERING COLUMN) M1 M M3 M6 RF PORT/WEBLINK PORT M6 TELEMATIC PORT M5 M4 VS1 1 : IMMOBILIZER 1 : IMMOBILIZER HARNESS M1 M 01 01 08 11 1 13 14 15 16 17 18 19 0 MS MS1 M3 01 BROWN/BLACK - PARKING LIGHT (-) OUTPUT GRAY (NC) PURPLE/GREEN - LOCK (-) OUTPUT 08 BLUE/GREEN - TRUNK/LIFTGATE (-) OUTPUT 11 GRAY/GREEN - HORN (-) OUTPUT 1 DKGREEN/GREEN - UNLOCK (-) OUTPUT M4 01 GRAY/BLACK (NC) GRAY/WHITE - HOOD STATUS (-) INPUT 08 87 86 87A 85 30 BROWN/RED BROWN/YELLOW GREEN/WHITE GREEN/PURPLE 15A VS4 VS3 CANH - CANL - 11 1V (+) PARKING LIGHT (-) - LIGHT (-) - TRUNK RELEASE (-) - UNLOCK (-) - 08 DISARM (-) - DRIVER DOOR PIN (OPEN) - 19 LOCK (-) - 0 HORN (-) - 01 1 OPTIONAL 1 : IGNITION 1 3 4 5 6 7 8 9 : IGNITION HARNESS C : GRAY 11 1 13 14 15 16 1 3 4 5 6 7 8 9 1 (C80G) : GRAY 1 11 9 8 7 6 5 4 3 1 4 3 1 0 19 18 17 16 15 14 13 (C80F) : WHITE 1 11 9 8 7 6 5 4 3 1 4 3 1 0 19 18 17 16 15 14 13 3 (C80E) : GREEN 1 11 9 8 7 6 5 4 3 1 4 3 1 0 19 18 17 16 15 14 13 1 BCM, BEHIND GLOVE BOX 3 OBDII PARKING LIGHT SWITCH 1 HOOD SWITCH INSTALL THE SUPPLIED HOOD SWITCH IF THE VEHICLE IS NOT EQUIPPED WITH ONE.
TYPE 4 - WIRE CHART - 1 OF 1 PAGE 13 OF 5 MAKE MODEL YEAR WIRE DESCRIPTION FORD NAME COLOR TYPE POSITION WIRE COLOR POLARITY MODULE LOCATION COMPONENT LOCATOR CanH C51 White 16 pin Gray/Orange (DATA) OBDII connector G CanL C51 White 16 pin 11 Purple/Orange (DATA) OBDII connector G Horn C18A Yellow 8 pin Blue/White (-) Steering lock connector, bottom of steering column G Transit STD key AT 15-18 Driver Door Pin C80C Brown 76 pin 44 Green/Purple (OPEN) BCM, driver side dash A Lock C80C Brown 76 pin 5 Gray/Yellow (-) BCM, driver side dash A Unlock C80C Brown 76 pin 56 Purple/Gray (-) BCM, driver side dash A Parking Light (front left) C80B Brown 46 pin 14 Green/Orange (+) BCM, driver side dash A Parking Light (rear left) C80B Brown 46 pin 15 Purple/Green (+) BCM, driver side dash A Parking Light (front right) C80C Brown 76 pin 66 Brown/Yellow (+) BCM, driver side dash A Parking Light (rear right) C80C Brown 76 pin 67 White/Orange (+) BCM, driver side dash A
TYPE 4 - WIRING DIAGRAM - 1 OF 1 PAGE 14 OF 5 VS IGNITION SWITCH (UNDER STEERING COLUMN) M1 M M3 M6 RF PORT/WEBLINK PORT M6 TELEMATIC PORT M5 M4 VS1 1 : IMMOBILIZER 1 : IMMOBILIZER HARNESS M1 M 01 01 08 11 1 13 14 15 16 17 18 19 0 MS MS1 M3 01 BROWN/BLACK - PARKING LIGHT (-) OUTPUT GRAY (NC) PURPLE/GREEN - LOCK (-) OUTPUT 08 BLUE/GREEN (NC) 11 GRAY/GREEN - HORN (-) OUTPUT 1 DKGREEN/GREEN - UNLOCK (-) OUTPUT M4 01 GRAY/BLACK (NC) GRAY/WHITE - HOOD STATUS (-) INPUT 08 BROWN/RED BROWN/YELLOW GREEN/WHITE GREEN/PURPLE 87 86 87A 85 30 3A 3A 3A 3A 15A VS4 VS3 CANH - CANL - 11 LOCK (-) - 5 DRIVER DOOR PIN (OPEN) - 44 UNLOCK (-) - 56 PARKING LIGHT FRONT RIGHT (+) - 66 PARKING LIGHT REAR RIGHT (+) - 67 PARKING LIGHT FRONT LEFT (+) - 14 PARKING LIGHT REAR LEFT (+) - 15 1V (+) : IGNITION 1 3 4 5 6 7 8 9 : IGNITION HARNESS 1 (C80C) : BROWN 11 1 13 14 15 16 1836 54 65 76 1735 53 1634 5 64 75 1533 51 143 50 1331 49 130 48 63 74 119 47 6 73 18 46 9 7 45 61 7 8 6 44 60 71 7 5 43 6 4 4 59 70 5 3 41 58 69 4 40 57 68 3 1 39 0 38 1 19 37 56 67 55 66 (C80B) : BROWN 1 46 15 45 14 44 31 4 13 43 1 4 30 1 11 41 9 0 40 9 39 8 3 19 8 38 7 7 18 37 6 36 6 17 5 35 4 34 5 16 3 33 3 1 BCM (DRIVER SIDE DASH) 1 OBDII STEERING LOCK (BOTTOM OF STEERING COLUMN) OPTIONAL 1 C18A : YELLOW HORN (-) - 1 HOOD SWITCH 1 3 4 5 6 7 8 INSTALL THE SUPPLIED HOOD SWITCH IF THE VEHICLE IS NOT EQUIPPED WITH ONE.
MODULE PROGRAMMING PROCEDURE ( KEYS) - 1 OF PAGE 15 OF 5 >> NOTE: To complete this procedure, both OEM keys are required. Wait, LED 1 will turn. (This may take up to 30 seconds) 11 ACC ON Remove key 1. 01 ACC ON Insert key 1 into ignition. >> NOTE: If the vehicle is not equipped with an immobilizer, press and hold the module s programming button during steps 7 and 8. 1 ACC ON Insert key into ignition. ACC ON Turn key 1 to ON position. LED will turn solid RED. ACC ON Insert key 1 into ignition. 13 ACC ON Turn key to ON position. LED 1 will flash GREEN. 08 ACC ON Turn key 1 to ON position. 14 Wait, LED will turn solid RED then will turn. ACC ON Turn key 1 to position. If LED turns solid GREEN for seconds: Module Programming Procedure completed. If LED turns solid RED, proceed with following step. 15 TIME RESTRICTION. Complete steps 13 and 14 within 4 seconds after LED turns. ACC ON Remove key 1. TIME RESTRICTION. Complete steps 08 to within 4 seconds after LED turns. 16 ACC ON Remove key.
MODULE PROGRAMMING PROCEDURE ( KEYS) - OF PAGE 16 OF 5 17 Press and release programming button. >> If the LED begins to flash RED, you are using a cloned key or used the same key twice. 18 Wait, LED will turn solid RED then will turn solid GREEN. 19 Module Programming Procedure completed.
VALET MODE PROGRAMMING PROCEDURE - 1 OF 1 PAGE 17 OF 5 >> NOTE: In Valet Mode, the Remote starter is not functional. Keyless entry, Lock and Unlock will remain functional. See RF kit user manual for alternate valet mode programming. >> To exit valet mode: repeat steps 1 to 5. 01 Time restriction. Complete next step within 7 seconds. ACC ON Cycle ignition ON five times [5x /ON] rapidly. ENGINE STOP Wait, LED 1 will turn solid RED for seconds. ACC ON Set ignition to position. ENGINE STOP Valet Mode Programming Procedure completed.
AFTERMARKET REMOTE PROGRAMMING - 1 OF 1 PAGE 18 OF 5 AFTERMARKET REMOTE PROGRAMMING: NOTES I All aftermarket remotes must be programmed to the RF-Kit. Refer to the RF-Kit user guide for aftermarket remote features and programming procedures.
PAGE 19 OF 5 MODULE NAVIGATION PROCEDURE - 1 OF 1 >> It is mandatory to exit the Module Navigation at the end of this procedure. Failure to exit the Module Navigation will drain vehicle battery. To exit the Module Navigation at any time: Follow STEP 13. >> Module must be programmed to the vehicle. >> Use the Module Navigation Chart on the next page. Set ignition to position. TO ACCESS THE MENUS: Press and hold programming button until LED 1 turns solid GREEN. 08 IN THE MENUS: Press the programming button as many times as the menu number indicates. LED 1 will flash GREEN an equal amount of times continuously. 01 ACC ON DOC.: #54456 01818 TO ACCESS THE OPTIONS: Press and hold programming button until LED 1 turns solid RED. IN THE OPTIONS: Press the programming button as many times as the option number indicates. LED 1 will flash RED an equal amount of times continuously. 11 TO ACCESS THE SETTINGS: Press and hold programming button until LED 1 turns solid GREEN. 1 Configure every other setting and proceed to step 13. [Z] LED 1 will flash GREEN as many times as the current (or default) setting number, continuously. 13 MANDATORY: EXIT MODULE NAVIGATION. Press and hold programming button for 7 seconds. LED 1 will flash RED rapidly. Release programming button. LED 1 will turn. [Z] IN THE SETTINGS: Press the programming button as many times as necessary to access your setting. LED 1 will flash GREEN an equal amount of times continuously. 14 Module navigation completed. To return to the MENUS: exit the Module Navigation and redo the Module Navigation Procedure. >> Failure to exit the Module Navigation will drain vehicle battery. [Y] To save and return to the OPTIONS: Press and hold programming button until LED 1 turns solid RED. [Y] LED 1 will flash RED as many times as the current option number continuously. ENGINE STOP [X]
MODULE NAVIGATION CHART - 1 OF PAGE 0 OF 5 MODULE NAVIGATION CHART: NOTES [X] MENUS [Y] OPTIONS [Z] SETTINGS I II Default settings are listed in bold. Make sure the option is covered on the vehicle before attempting to change the setting. *Vehicle will shutdown when a door is opened. 01 CONFIGURATION 01 DISARM/UNLOCK BEFORE 01 ON RELOCK AFTER 01 ON RELOCK AFTER SHUTDOWN 01 ON FORCE UNLOCK ALL ON FIRST PRESS 01 ON TAKEOVER 01 ENABLE DISABLE* N/A 01 N/A 01 DISABLE FACTORY KEYLESS RS SEQUENCE N/A LOCK + UNLOCK + LOCK LOCK + LOCK + LOCK 01 MIN MIN MIN 08 MODULE RUN TIME 15 MIN 5 MIN 30 MIN 35 MIN 08 15 MIN 01 SEC SEC 08 SEC WAIT TO DELAY SEC 15 SEC 0 SEC 5 SEC 08 30 SEC N/A 01 N/A 11 N/A 01 N/A 1 N/A 01 N/A 13 N/A 01 N/A
MODULE NAVIGATION CHART - OF PAGE 1 OF 5 MODULE NAVIGATION CHART: NOTES [X] MENUS [Y] OPTIONS [Z] SETTINGS *Vehicle will shutdown when a door is opened. 01 DOUBLE LOCK 14 HORN EVENT TRIGGER LOCK + UNLOCK LOCK + UNLOCK + 01 CONFIGURATION DOUBLE LOCK + 01 30 msec 15 HORN CHIRPS WIDTH 15 msec 60 msec - Technical Support only 01 N/A 01 N/A
REMOTE ER ERROR CODES - 1 OF 1 PAGE OF 5 REMOTE ER ERROR CODES: NOTES [X] NUMBER OF PARKING LIGHT FLASHES DIAGNOSTIC I II WARNING: The following applies only when the parking lights are connected and supported by the system. After a remote starter failure, the parking lights will flash [X] number times to indicate an error code. See table. Foot brake is ON. Hood is open. Engine tach signal is lost. System is in Valet Mode. Vehicle is moving (VSS). 08 Glow plug timeout error. RS not synchronized. Start vehicle with OEM key for 15 sec before trying a new RS sequence. N/A 11 N/A 1 N/A 13 N/A 14 N/A 15 N/A 16 CAN communication failure during RS sequence.
MODULE DIAGNOSTICS - 1 OF 1 PAGE 3 OF 5 TEST MODULE LED 1 STATUS DIAGNOSTIC I II III DURING PROGRAMMING DURING REMOTE WITH IGNITION Flashing RED Solid RED Flashing GREEN Solid GREEN then Flashing RED Solid RED Flashing GREEN Solid GREEN then Flashing RED Solid RED Flashing GREEN Solid GREEN then Missing/wrong information from firmware or vehicle. Module waiting for more vehicle information. Additional steps required to complete module programming. Module correctly programmed. No activity or module already programmed. Module incorrectly programmed. Module incorrectly programmed. Module correctly programmed and operational. Reset in progress. Invalid ground when running status from remote starter. Module incorrectly programmed or connected. Module not programmed. Waiting for more vehicle information. False ground when running status from remote starter. Reset in progress. Module at rest and ready for a remote start sequence.
MODULE RESET PROCEDURE - 1 OF 1 PAGE 4 OF 5 01 Disconnect all connectors from module except the BLACK 0-PIN connector. Reconnect all connectors. Disconnect the BLACK 0-PIN connector. 08 Repeat programming procedure. PRESS AND HOLD the module s programming button while connecting the BLACK 0-PIN connector. >> Failure to follow procedure may result with a DTC or a CHECK ENGINE error message. Wait, LED 1 will flash RED. RELEASE programming button. LED 1 will turn RED for seconds. Module RESET completed.
INSTALLATION CHECKLIST - 1 OF 1 PAGE 5 OF 5 1 WARNING: Vehicle engine will start many times. Test in a well ventilated area. Close all vehicle doors, hood and trunk. 3 Press the LOCK button once [1x] on the aftermarket keyfob. Question 1: Do the doors lock? YES: Go to next step. NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists. 4 Press the UNLOCK button once [1x] on the aftermarket keyfob. Question : Do the doors unlock? YES: Go to next step. NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists. 5 Press the TRUNK release button once [1x] on the aftermarket keyfob if supported. Question 3: Does the trunk or hatch open/unlock? YES: Close trunk or hatch and go to next step. NO: Verify the remote programming, the RF connections and the wired trunk/hatch connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists. 6 Press the AUX 1 button once [1x] on the aftermarket keyfob if supported. Question 4: Does the driver side sliding door open? YES: Press the AUX 1 button once [1x] to close the driver sliding door and go to next step. NO: Verify the remote programming and the RF connections. Repeat the test and call technical support, if the problem persists. 7 Press the AUX button once [1x] on the aftermarket keyfob if supported. Question 5: Does the passenger side sliding door open? YES: Press the AUX button once [1x] to close the passenger sliding door and go to next step. NO: Verify the remote programming and the RF connections. Repeat the test and call technical support, if the problem persists. 8 Press the /STOP button once [1x] on the aftermarket keyfob to remote start vehicle. Question 6: Does the vehicle remote start? YES: Go to next step. NO: Verify the remote programming, the RF connections and check the remote start error codes. Repeat the test and call technical support, if the problem persists. CHECKLIST 9 Press the /STOP button once [1x] on the aftermarket keyfob to shut down vehicle. Question 7: Does the vehicle shut down? YES: Go to next step. NO: Repeat step. If problem persists, press the brake pedal once [1x] to shut down the vehicle and call technical support. RAP and auto light shutdown test Question 8: Did the radio, interior controls and headlights turn off within 60 seconds after remote start shutdown? YES: Go to next step. NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support if the problem persists. 11 Open hood. 1 If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step. 13 Press the /STOP button once [1x] on the aftermarket keyfob to remote start vehicle. Question 9: Does the vehicle remote start? YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test. NO: Go to next step. 14 Close hood. 15 Enter vehicle and close the doors. 16 Press the /STOP button once [1x] on the aftermarket keyfob to remote start vehicle. 17 Wait for the vehicle to start. 18 Press brake pedal. Question : Does the vehicle shut down? YES: Go to next step. NO: The module does NOT detect the brake pedal signal. Press the /STOP button once [1x] on the aftermarket keyfob to shut down vehicle, check connection as illustrated in the wiring diagram, if applicable, and call technical support. 19 Exit vehicle. 0 Installation checklist completed.