Compact Select Cylinders Inch Series
Table of Contents: Inch Series Inch Series, Options and ccessories Inch Series How to Order: Inch Series... pg. Forces, Pressure Ratings, Envelope Dimensions... pg. Mounting... pgs. -6... pg. 7 Component Descriptions... pg. 8 Dimensions / Bore Cylinder... pgs. 0- / Bore ccessories... pgs. 5-0 / - 8 Bore Cylinders... pgs. -70 / - 8 Bore ccessories... pgs. 7-86 Sensors... pgs. 87-88 lignment Couplers... pgs. 89-90 Flow Controls... pgs. 9-9 Technical Information... pgs. 9-96 Maintenance and Repair Kits... pgs. 97-98 Modified Products... pgs. 99-0 -D Models available online at www.compactautomation.com www.compactautomation.com (86) 67-95
Inch Series Example: SFHD8X-FFHTV S R B T Magnetic Piston (Optional) Magnetic piston cylinder with sensor mounting rail NOTE: Leave blank for standard option. Mounting Style Square, end mount Round, end mount Base, side mount Thin, side mount MGNETIC PISTON MOUNTING STYLE S How to Order: Inch Series DUTY FH BORE SIZE 8 5 5 (Optional) Half Husky - Intermediate HH duty (available on single rod end only) FH Full Husky - Heavy duty NOTE: Leave blank for standard option. D End (Optional) Double rod end DOUBLE D 6 X STROKE LENGTH 6 - OPTION XXX 7 OPTION 7 Options (String option codes in alphabetical 8 Seal Option order to the right of the "-" including seal option) Standard Buna-N 0º - 00ºF (-8º - 9ºC) Mounting Options Optional Seals EB End Bracket SP Short Pivot Pneumatic FF Front Flange SRC Short Rear Clevis High temperature 0º - 00ºF HTV LP Long Pivot Short Rear Clevis w/ Eye viton (-8º - 0ºC) SRCE NM** Nose Mount Mount Corrosion resistant PS Pivot Shaft TBE Threads Both Ends Not recommended 50º - 00ºF CRT* R Reverse ssembly TF Threads Front for use under (º - 0ºC) 50º F RF Rear Flange TM Thru Mount SB Side Bracket TR Threads Rear Ethylene -70º - 00ºF ETP Rod End Options Propylene (-57º - 50ºC) CBSS Clevis Bracket Set Screw HR Hollow Rod, Option Hydraulic EX Extension, End HR Hollow Rod, Option 0º - 50ºF EXD Extension on MS/MSD Male Stud/MS Double End HYD* Buna-N hydraulic (-8º - ºC) EXF Front End Extension on NR* Non-Rotating 0º - 00ºF NT** Jam Nut VHYD* Viton hydraulic (-8º - 0ºC) EXR Rear End Extension on RE Rod Eye RES Rod Eye, short head design *NOTE: Not available in / bore. FT Fine Threads Rod Wiper/Rod Wiper RW/RWD Double End CR - Corrosion Resistant 00 Other Series Stainless Steel DJ djustable Retract Stroke UB Urethane Bumper - Both ends Specify before part number. P Positive lignment UC Urethane Cushion - Front end vailable on / through. UB Urethane Bumper - Front end UC Urethane Cushion - Rear end See pages 6 and 7 for details. UB Urethane Bumper - Rear end UC Urethane Cushion - Both ends Ports Modifications Welcome 8NPT /8" National Pipe Thread Fine NPT /" National Pipe Thread Fine Special stroke lengths, port orientation, *NOTE: See Non-Rotating option on page 78. mounting configuration. **NOTE: See Nose Mount option page 86. www.compactautomation.com (86) 67-95 XXX Bore /" -/" /" " 8 -/8" " 8 -/8" 5 5" 58-5/8" 6 6" " 8 8" Stroke Length (Stroke lengths are available in /8" increments) See catalog pages for stroke availability for each bore size. Example: -/8 = 8 / = 8
Forces, Ratings & Envelope Dimensions Cylinder Force and Pressure Rating Formula: Example: Force (lbs.) = Piston rea (In ) x Pressure (PSI).5 In (Piston rea) x 50 PSI (Pressure) = 5 lbs. Force Bore Piston rea (In ) / / -/8 -/8-5/8 -/ 5 Pre-Calculated Force in Pounds 60 PSI 80 PSI 00 PSI Push. 6 0 Pull.5 9 5 Push. 6 5 Pull.6 9 6 Push.0 60 80 00 Pull.8 8 6 80 Push.5 90 0 50 Pull. 7 96 0 Push.0 0 60 00 Pull.7 0 6 70 Push. 86 8 0 Pull.8 68 80 Push.9 9 9 90 Pull.5 70 60 50 Push 7.0 0 560 700 Pull 6.6 96 58 660 Push.6 756 008 60 Pull. 76 968 0 Push 9.6 76 568 960 Pull 9. 5 56 90 5" FH Pull 8.8 8 50 880 6 8 Push 8. 698 6 80 Pull 7.5 650 00 750 Push 50. 08 0 500 Pull 9.5 970 960 950 Envelope Dimensions Bore Standard Intermediate Heavy / 0.69 0.8 0.9.00 X.75. / 0.8.06..5 Sq. -/8 0.88..8 Sq..88 -/8..8.6.75 Sq.. -5/8..8.6.00 Sq..8.5.75 Sq..00 -/.8.6.88.00 Sq..6.88. Sq..00.75.00.5 5.00 5.88..8 6.00 6. 7.00 S D Pressure Rating (PSI) Pneumatic Hydraulic 5 50 500 50 500 50 500 50 500 50 500 50 500 50 500 00 00 00 00 00 S SQURE D DIMETER 8.8 9.00 www.compactautomation.com (86) 67-95 Conversions PSI to BR PSI = 0,069 bar Example: 5 PSI X 0,069 =.7 BR Pound to Kilograms pound = 0,5 kilograms Example: 5 lbs. x 0,5 =,5 kilograms + / FOR MGNETIC PISTON OPTION
/ through Bore Non Magnetic Piston Ordering Prefix S Optional Mounting Magnetic Piston Ordering Prefix S Square - end mount - cylinders have one or more of the following patterns as standard. Each dimensional page lists standard and optional mounting suffix codes. Threads Front Standard on all cylinders Tapped mounting holes on the rod end Thru Mount Ordering Suffix TM Threads Rear Ordering Suffix Square - End Mount - Cylinder TR Tapped mounting holes opposite the rod end Threads Both Ends Ordering Suffix TBE vailable on: / Bore through -/8 body length / - Bore through stroke length For longer stroke lengths - Check mounting screw availability. Modifications welcome - consult factory. Tapped mounting holes on both ends Icon represents mounting style on each dimensional page. Sensors Sold Separately See Sensors pages 87-88 Counterbored mounting holes, both ends, for drop through bolt Non magnetic piston cylinders - When TR is specified or when using Bolt On Hardware options, the cylinder may be reverse assembled, see Technical Data section page 9 for detailed explanation. To avoid changing port orientation, specify suffix: TBE. www.compactautomation.com (86) 67-95
Round - End Mount - Cylinder / through 8 Bore Non Magnetic Piston Ordering Prefix R Optional Mounting Magnetic Piston Ordering Prefix R Round - end mount - cylinders have one or more of the fol lowing patterns as standard. Each dimensional page lists standard and optional mounting suffix codes. Threads Front Standard on all cylinders Tapped mounting holes on the rod end Thru Mount Ordering Suffix Thru mounting holes for drop through bolt TM Threads Rear Ordering Suffix TR Tapped mounting holes opposite the rod end Threads Both Ends Ordering Suffix TBE vailable on: / - 8 Bore through stroke length For longer stroke lengths - Check mounting screw availability. Modifications welcome - consult factory. Tapped mounting holes on both ends Icon represents mounting style on each dimensional page. Sensors Sold Separately See Sensors pages 87-88 Non magnetic piston cylinders - When TR is specified or when using Bolt On Hardware options, the cylinder may be reverse assembled, see Technical Data section page 9 for detailed explanation. To avoid changing port orientation, specify suffix: TBE. 5 www.compactautomation.com (86) 67-95
/ through Bore Non Magnetic Piston Ordering Prefix B Optional Port Position Magnetic Piston Ordering Prefix B Base - Side Mount - Cylinder Base - side mount - cylinders have one standard mounting and port location, below are examples of optional positioning. Sensors Sold Separately See sensors pages 87-88 / Bore Cylinder may be Reverse ssembled consult factory - See Technical Data page 9 for detailed explanation. / through Bore Non Magnetic Piston Cylinders Optional positions are available as shown below: COMPCT reserves the right to plug existing ports, without notification, unless specified otherwise. Standard Location Example Side number Port Position Example Ordering Suffix PP Magnetic Piston Cylinders lternate port locations are available, consult factory for information. / Bore Only Non Magnetic Piston Ordering Prefix T Magnetic Piston Ordering Prefix T Port Position Example Ordering Suffix PP Icon represents mounting style on each dimensional page. Thin - Side Mount - Cylinder Icon represents mounting style on each dimensional page. www.compactautomation.com (86) 67-95 Sensors Sold Separately See Sensors pages 87-88 6
7 Types Double cting COMPCT Cylinders - Single and End Standard COMPCT Cylinders Our most space efficient duty. Short rod bearing and thin piston design are for guided loads. vailable as single or double rod end. Components and Material Standard End End Standard or Heavy Optional Magnetic Piston - vailable on any cylinder, style or duty. (Not shown.) Heavy Ordering Suffix FH Full Husky Longer rod bearing plus thicker piston are for heavy duty service. vailable as single or double rod end. Heavy End Description End Cap luminum Intermediate Ordering Suffix HH Retaining Wire Stainless Steel Rod Bearing Sintered bronze Cylinder Body luminum 5 Piston Rod Stainless steel Half Husky combination of our standard and Full Husky duty. Long rod bearing and thin piston design are for medium duty service. vailable as single rod end only. Intermediate End Material 6 Piston Seal Low friction Nitrile 7 End Cap Seal O-ring (Nitrile) 8 Piston luminum 9 Rod Seal Low friction Nitrile 0 Husky Rod Bearing Bronze Husky End Cap luminum Husky Piston luminum Snap Ring Carbon spring steel Snap-Cap, Magnetic Piston and Hydraulic option cylinder constructions may deviate from above listing - consult factory for additional information. www.compactautomation.com (86) 67-95
Components and Material.) Port Orifices Enter directly into the bore; no turns, tapers or cross drilling. Crisp, powerful response to pneumatic pressure provides speed, control, and faster cycle time. B.) C.) D.) E.) F.) Factory Lubrication Is standard on all cylinders and does not require air line induced lubrication, although additional air line lubrication may be used. Lubricated air that is compatible with petroleum based grease containing Teflon is recommended. Non-lubricated air is recommended to operate the cylinder. End Caps re machined of high grade aluminum alloy and anodized for protection against corrosion. / bore end caps feature our patented Snap-Cap design - resilient retainer seal that aids in absorbing piston impact. / bore and larger feature our patented wire retainer design. Optional urethane cushions may be added when additional impact resistance is required, available on / - bore. Retaining Wire Is a patented stainless wire-form end cap retainer. This design provides more security than common fasteners and tie rods. It is easily removed for maintenance or seal replacement. Rod Bearing Varies according to duty and bore size. / Bore Snap-Cap ll duties - Sintered bronze / through 5 Bore ll duties - Sintered bronze 6 through 8 Bore ll duties - Bearing bronze Cylinder Body Is a thick-walled, clear anodized, aluminum extrusion. Tight tolerances and concentricity guarantee longer life. Total Compact envelope is up to 60% smaller than typical cylinders. G.) Seals re constructed of high grade, low friction, Nitrile materials. Optional seal materials, fluorocarbon and PTFE, are available See Seal Descriptions in the Options section. Component Description H.) Piston Construction / Bore is a solid one piece construction on both the single and double rod end cylinders. / through 8 Bore Single rod end cylinders - the lightweight aluminum piston is attached to the rod with a flat head socket screw. thread adhesive is used to assure sealing and secure the assembly from shock and vibration damage. Double rod end cylinders - the piston and rod feature a snap ring construction. Consult factory for alternative double piston shaft assembly construction. www.compactautomation.com (86) 67-95 8
Modifications Unique pplication Examples For technical assistance and quotes contact your local distributor or our Technical Sales Department (86) 67-95. Standard Product Square End Mount Cylinder Standard duty Standard port style and location Standard rod end Highly modified to meet the Customer s application requirements Modified Through Mount Cylinder Special duty including extended rod bearing and rod wiper Custom port style and location Special rod end with rod end attachment Modifications... simple solutions to space problems. We have over 50,000 files of modified or special cylinder designs. Examples range from simple porting changes to 00% custom designed cylinders. Our standard product design is a simple, plain extrusion, which allows us to easily modify our product to meet many unusual or unique requirements. Our design also allows modifications at a cost effective price and quick delivery. In the Modified Products section we offer two Request for Quote fax forms to assist in a quick quote on your specifications via your local distributor. Simple Solutions Hollow piston rods Tunneled air ports Frame modifications Modified rod ends Multi-position cylinders Back-to-back cylinders Modified locations on: sensors, mounting and porting Multi-piston (multi force) Complex Solutions Extreme space limitations Multi-cylinder blocks Pneumatic industrial hand tools Load bearing cylinders 9 www.compactautomation.com (86) 67-95
Style R / Bore Non Magnetic Piston B Standard Rx RDx /8 to in /8" increments.69. Intermediate RHHx /8 to in /8" increments.8. Heavy RFHx RFHDx /8 to in /8" increments.9.7 Standard Mounting: TF. DI #8- TP X. DP 7/ WRENCH FLTS Optional Mounting: TR, TBE, TMF, TMR Standard Rx RDx /8 to in /8" increments.9 Intermediate RHHx /8 to in /8" increments.06 Heavy RFHx RFHDx /8 to in /8" increments.9 Standard Mounting: TF #6- TP BY /8 DEEP ON.88 B.C. ( PLCES, 80º PRT). DI 90º.0.06.5 #0- X.9 DP ( PLCES, IN LINE) Optional Mounting: TR, TBE, TMF, TMR #6- TP BY.8 DP ON.88 BOLT CIRCLE ( PLCES, 80º PRT) 90º.06.5DI + STROKE B + STROKE.0.0.0.06 + STROKE DOUBLE END ONLY / Bore Magnetic Piston.06+ STROKE DOUBLE END ONLY #0- X.9 DP #8- TP X.8 DP ( PLCES, IN LINE) Due to physical size, body lengths -/ and shorter have only one sensor; Body length = + stroke -.06. For modifications, consult factory. www.compactautomation.com (86) 67-95 End Mount THIRD NGLE Style R End Mount 0
Style S End Mount / Bore Non Magnetic Piston Snap-Cap Design Standard Mounting: TF Standard Mounting: TF.06 DI..7. #8- TP X. DP.5 (MIN) DP ON.00 BODY LENGTH ND SHORTER 7/ WRENCH FLTS.00.7.75 #6- TP X.8 DP.6.0 TM OPTION - C BORE FOR #6 SHCS VILBLE ON BODY LENGTHS -/8 ND SHORTER ONLY.0.06 + STROKE STYLE SD OR SFHD #0- TP X.9 DP / Bore Magnetic Piston Snap-Cap Design.06 DI..7. #8- TP X. DP.5 (MIN) DP ON.00 BODY LENGTH ND SHORTER 7/ WRENCH FLTS Due to physical size, body lengths -/ and shorter have only one sensor; Body length = + stroke -.06. For modifications, consult factory. Optional Mounting: TR, TBE, TM Optional Mounting: TR, TBE, TM SENSOR MOUNTING TRCK Standard Sx SDx /8 to in /8" increments.69 Intermediate SHHx /8 to in /8" increments.8 Heavy SFHx SFHDx /8 to in /8" increments.9 Style S End Mount Standard Sx SDx /8 to in /8" increments.9 Intermediate SHHx /8 to in /8" increments.06 Heavy SFHx SFHDx /8 to in /8" increments.9.00.7.86.6 #6- TP X.8 DP.0 TM OPTION - C BORE FOR #6 SHCS VILBLE ON BODY LENGTHS -/8 ND SHORTER ONLY.0.06 + STROKE STYLE SD OR SFHD #0- TP X.9 DP www.compactautomation.com (86) 67-95 THIRD NGLE
...5..5 / Bore Non Magnetic Piston Snap-Cap Design..5 Due to physical size, body lengths -/ and shorter have only one sensor; Body length = + stroke -.06. For modifications, consult factory..06 #6- TP X. DP ( PLCES) DI.00 #8- TP X. DP.5 (MIN) DP ON.00 BODY LENGTH ND SHORTER 7/ WRENCH FLT / Bore Magnetic Piston Snap-Cap Design.5.06 #6- TP X. DP ( PLCES) DI Standard Tx TDx /8 to in /8" increments.69 Intermediate THHx /8 to in /8" increments.8 Heavy TFHx TFHDx /8 to in /8" increments.9.00.75 Standard Tx TDx /8 to in /8" increments.9 Intermediate THHx /8 to in /8" increments.06 Heavy TFHx TFHDx /8 to in /8" increments.9.6 SENSOR MOUNTING TRCK #8- TP X. DP.5 (MIN) DP ON.00 BODY LENGTH ND SHORTER 7/ WRENCH FLTS.0.0.06 + STROKE STYLE TD OR TFHD #0- TP X.9 DP.0.06 + STROKE STYLE TD OR TFHD.0.6.86 #0- TP X.9 DP Style T Side Mount THIRD NGLE Style T Side Mount www.compactautomation.com (86) 67-95
Style B Side Mount / Bore Non Magnetic Piston Snap-Cap Design Standard Bx BDx /8, /.69 Intermediate BHHx /8.8.06 DI. #8- TP X.5 DP 7/ WRENCH FLTS #8- TP X.8 (MIN) DP 7/ WRENCH FLTS #8- TP X. DP 7/ WRENCH FLTS.75.00. #8- TP THRU THRU MOUNT FOR # SHCS.0 DI C BORE X. DP ( PER SIDE).75 NOTE: MINIML CLERNCE FOR IR FITTING.6.0 #8- TP THRU THRU MOUNT FOR # SHCS.0 DI C BORE X. DP ( PER SIDE).0.0.6 NOTE: MINIML CLERNCE FOR IR FITTING #8- TP THRU THRU MOUNT FOR # SHCS.0 DI C BORE X. DP ( PER SIDE).06 + STROKE STYLE BD #0- TP X.9 DP Standard Bx BDx /8 to -/ in /8" increments.69 Intermediate BHHx / to -/8 in /8" increments.8 Heavy BFHx BFHDx /8 to in /8" increments.9 Standard Bx BDx -/8 to in /8" increments.69 Intermediate BHHx -/ to in /8" increments.8 Heavy BFHx BFHDx -/8 to in /8" increments.9.06 + STROKE STYLE BD OR BFHD #0- TP X.9 DP www.compactautomation.com (86) 67-95.06 + STROKE STYLE BD OR BFHD THIRD NGLE
.06 / Bore Magnetic Piston Snap-Cap Design DI C L.75...00 #8- TP THRU THRU MOUNT FOR # SHCS.0 DI C BORE X. DP ( PER SIDE) SENSOR MOUNTING TRCK.8 #8- TP X.8 (MIN) DP 7/ WRENCH FLTS Standard Bx BDx /8 to in /8" increments.9 Intermediate BHHx /8 to 7/8 in /8" increments.06 Heavy BFHx BFHDx /8 to / in /8" increments.9.06.6 Standard Bx BDx -/8 to in /8" increments.9 Intermediate BHHx to in /8" increments.06 Heavy BFHx BFHDx 7/8 to in /8" increments.9 #8- TP THRU THRU MOUNT FOR # SHCS.0 DI C BORE X. DP ( PER SIDE) #8- TP X. DP 7/ WRENCH FLTS Due to physical size, body lengths -/ and shorter have only one sensor; Body length = + stroke -.06. For modifications, consult factory. www.compactautomation.com (86) 67-95.0.0.06 + STROKE STYLE BD OR BFHD #0- TP X.9 DP.06 + STROKE STYLE BD OR BFHD Style B Side Mount THIRD NGLE
/ Bore Options Conversion Formula: Cº = (Fº - º) x.56 Type Ordering Suffix Nitrile Fluorocarbon HTV Rating 0 to 00 F -8 to 9 C 0 to 00 F -8 to 0 C TR Mounting Threads on Rear (Optional; specify TR after bore and stroke.) TMF Mounting Thru-Mount (Front) (Optional; specify TMF after bore and stroke.) C bored for #6 SHCS on shaft end only. vailable only on -/8 body lengths and shorter. Pneumatic Seals Description Most commonly used elastomer O-ring due to its excellent resistance to petroleum products, wear, tear and friction. Works with lubricated or non-lubricated air in the noted temperature range. Recommended for general purpose sealing with petroleum oils and fluids, water and silicone greases and oils. Used mainly for elevated temperatures, harsh environments where some coolants, solvents, cleaning agents or other chemicals will contact the seal gland. Lower compression set is characteristic. For your specific requirements, consult factory. / Bore Round Body Cylinder Options Threaded Nose Mount Threaded Nose Mounting for R Series Cylinder Option NM. DI.5 DI ROD. (THRED LENGTH) PILOT DI /-0 THRED..06 STNDRD DUTY SNP-CP CYLINDER NOT VILBLE IN HUSKY DUTY TBE Mounting Threads on Both Ends (Optional; specify TBE after bore and stroke.) TMR Mounting Thru-Mount (Rear) (Optional; specify TMR after bore and stroke.) C bored for #6 SHCS on rear end only. vailable only on -/8 body lengths and shorter. = /6 on all Stroke Cylinders except: = /6 on -5/8 and -7/8 Stroke Standard Cylinders = /6 on -/8 and -5/8 Stroke Magnetic Standard Cylinders 5 www.compactautomation.com (86) 67-95
Corrosion Resistant 00 Series Stainless Steel Standard Features: 00% 00 series stainless steel components interior and exterior Plastic rod bearings Intermediate and Heavy Features: 00% 00 series stainless steel components interior and exterior Plastic rod bearings Magnetic Piston Cylinders: Bolt-on Mounting Track is aluminum only Ordering: Specify CR before cylinder part number Delivery: Non-standard delivery, consult factory djustable Retract Stroke DO NOT use with any pivoting applications LOCKNUT.5 DI THRED SEL #0- SET SCREW STOP VILBLE LENGTHS: / TO (IN /8 INCREMENTS) / Bore Options RER END CP LENGTH VRIES WITH DJUSTMENT Positive lignment vailable on S and R style cylinders only The alignment pocket and pilot are designed to fit between the cylinder and the mounting surface. This ensures accurate mounting and added shear strength. lignment Pocket Provides positive means of locating cylinder centerline within.005 P Ordering Suffix: P Style: S and R Rod: Single.5 DI x. DP lignment Pilot Sold separately. +.000 -.00.5 DI CR Ordering Prefix: CR Material: 00 Series stainless steel DJ Specify Length Ordering Suffix: DJ_ Length: / - in /8 increments Rod: Single only Temperature: 00ºF Max. Material: luminum endcap, steel locknut and thread seal PL : Material: ll Styles THIRD NGLE pplications: Chemical / Petroleum Medical Equipment Salt Water Exposure Clean Rooms Food Processing Electronic ssembly Nuclear Pharmaceutical PL Stainless steel www.compactautomation.com (86) 67-95 ll dimensions are in inches unless otherwise noted. 6
7 ll Styles / Bore Options Hollow Rod Option Our hollow rod option is available for applications that require passage through a double ended rod. vailable on / - stroke in /8 increments. Male Stud #8-. Clevis Bracket with Set Screw... SQ.6.6.06..6 M X 0.5 TP X.5 DP (BOTH ENDS).09 DRILL THRU Double ended unit has stud in front end only. If male stud is desired on both ends, specify MSD. Male stud thread: Same pitch and diameter as female rod tap. DI PIN. #8- THRED THIRD NGLE HR Ordering Suffix: HR Rod: Double only pplications Example YES NO Gases Liquids Vacuum Linear / Rotary Cylinder Clamp and Punch Cylinder Blow Molding Cylinder Hydraulic Cylinders Non-Rotating Rods MS56 Ordering Suffix: MS56 Material: Steel black oxide CBSS THIRD NGLE Ordering Suffix: CBSS Material: Steel black oxide with case hardened pin and clips X X Clevis Bracket www.compactautomation.com (86) 67-95 ll dimensions are in inches unless otherwise noted.
Rod End Extension EX_ SINGLE ROD END EXD_ For special extension or length - consult factory Not a screw on component Female tap does not change Rod Eye. SQ.6 Screws flush with cylinder rod face DOUBLE ROD END EXD_ Extended equally at both ends..6. DI.5 #8- THRED / Bore Options EXF_ DOUBLE ROD END End EX Specify Length RE EXR_ Extension Front End EXF Specify Length Ordering Suffix: Material: End EXD Specify Length ll Styles THIRD NGLE Extension Rear End EXR Specify Length Ordering Suffix: EX, EXD, EXF or EXR Length: /8 - in /8 increments RE Steel black oxide with sintered bronze bearing www.compactautomation.com (86) 67-95 ll dimensions are in inches unless otherwise noted. 8
9 Style S End Mount S.6 S. / Bore Options Short Rear Clevis with Eye Mount.75.7.59.75.5.59.0.6 Short Rear Clevis.08..00.06.6.00. DI Cylinder is reverse assembled with magnetic piston option..6 0º.. DI Cylinder is reverse assembled with magnetic piston option...6 SRCE Ordering Suffix: SRCE Style: S only Rod: Single only Pivot: 80º Material: Short Rear Clevis: See Below Eye Mount: Steel black oxide SHORT RER CLEVIS SRC EYE MOUNT THIRD NGLE Ordering Suffix: SRC Style: S only Rod: Single only Material: Short Rear Clevis: Steel black oxide with case hardened pin and clips www.compactautomation.com (86) 67-95 ll dimensions are in inches unless otherwise noted.
ww w. ma br co m. al. gr
Style S End Mount. / Bore Non Magnetic Piston Standard Sx SDx /8 to / in /8" increments.8 Intermediate SHHx /8 to / in /8" increments.06 Heavy SFHx SFHDx /8, /. Standard Mounting: TF, TR, TBE, TM.8.06. DI.9.88 #0- TP X.5 (MIN) DP / WRENCH FLTS.9.88 #0- TP X. DP / WRENCH FLTS Optional Porting: /8-7 NPTF.5 SQ /-0 TP THRU MOUNT FOR #0 SHCS. DI C BORE X.0 DP ( PER END) Standard Sx SDx 7/8,.8 Intermediate SHHx 5/8, /.06 Heavy SFHx SFHDx /8, /. Standard Mounting: TF, TR, TBE, TM Optional Porting: /8-7 NPTF. /-0 TP THRU MOUNT FOR #0 SHCS. DI C BORE X.0 DP ( PER END) Standard Sx SDx -/8 to 6 in /8" increments.8 /-0 TP #0- TP X. DP.8.06 + STROKE STYLE SD OR SFHD..8.6.8. (MIN).78 (MIN) Intermediate SHHx 7/8 to 6 in /8" increments.06 Heavy SFHx SFHDx 5/8 to 6 in /8" increments. Standard Mounting: TF Optional Mounting: TR, TBE, TM Optional Porting: /8-7 NPTF www.compactautomation.com (86) 67-95.06 + STROKE STYLE SD OR SFHD #0- TP X. DP.06 + STROKE STYLE SD OR SFHD THIRD NGLE
Standard Mounting: TF, TR, TBE, TM..8.06. DI.9.88.9 #0- TP X.8 (MIN) DP / WRENCH FLTS SENSOR MOUNTING TRCK #0- TP X. DP / WRENCH FLTS SENSOR MOUNTING TRCK Optional Porting: /8-7 NPTF.5 SQ.88 / Bore Magnetic Piston Standard Sx SDx /8 to / in /8" increments.06 Intermediate SHHx /8, /.. /-0 TP THRU MOUNT FOR #0 SHCS. DI C BORE X.0 DP ( PER END) Standard Sx SDx 5/8 to / in /8" increments.06 Intermediate SHHx /8 to / in /8" increments. Heavy SFHx SFHDx /8 to / in /8" increments.56 Standard Mounting: TF, TR, TBE, TM Optional Porting: /8-7 NPTF..8 /-0 TP THRU MOUNT FOR #0 SHCS. DI C BORE X.0 DP ( PER END) /-0 TP.6.8.8.5 (MIN).78 (MIN) Standard Sx SDx 7/8 to 6 in /8" increments.06 Intermediate SHHx 5/8 to 6 in /8" increments. Heavy SFHx SFHDx /8 to 6 in /8" increments.56 Standard Mounting: TF Optional Mounting: TR, TBE, TM Optional Porting: /8-7 NPTF.06 + STROKE STYLE SD #0- TP X. DP.06 + STROKE STYLE SD OR SFHD #0- TP X. DP.06 + STROKE STYLE SD OR SFHD Style S End Mount THIRD NGLE www.compactautomation.com (86) 67-95
Style B Side Mount / Bore Non Magnetic Piston Optional Porting: /8-7 NPTF..8 #0- TP X. DP.8 #0- TP X. DP.8.06. DI. Optional Porting: /8-7 NPTF.8. Standard Bx BDx /8 to / in /8" increments.8 Intermediate BHHx /8 to / in /8" increments.06 Heavy BFHx BFHDx /8, /..5 SQ #0- TP X.5 (MIN) DP / WRENCH FLTS Standard Bx BDx 7/8 to 6 in /8" increments.8 Intermediate BHHx 5/8 to 6 in /8" increments.06 Heavy BFHx BFHDx /8 to 6 in /8" increments. #0- TP X. DP / WRENCH FLTS.9.9.88.88.8.8 #0- TP X.5 DP.8 #0- TP X.5 DP ( PLCES) THIRD NGLE.06 + STROKE STYLE BD OR BFHD.06 + STROKE STYLE BD OR BFHD www.compactautomation.com (86) 67-95
..8 #0- TP X. DP.8 #0- TP X. DP Optional Porting: /8-7 NPTF.06.8. DI. #0- TP X.8 (MIN) DP / WRENCH FLTS Optional Porting: /8-7 NPTF.8. #0- TP X. DP / WRENCH FLTS.5 SQ / Bore Magnetic Piston Standard Bx BDx /8 to / in /8" increments.06 Intermediate BHHx /8, /. SENSOR MOUNTING TRCK.9.88.8 SENSOR MOUNTING TRCK Standard Bx BDx 5/8 to 6 in /8" increments.06 Intermediate BHHx /8 to 6 in /8" increments. Heavy BFHx BFHDx /8 to 6 in /8" increments.56.9.88.8 #0- TP X.5 DP ( PLCES) #0- TP X.5 DP Style B Side Mount THIRD NGLE.06 + STROKE STYLE BD.8.06 + STROKE STYLE BD OR BFHD www.compactautomation.com (86) 67-95
Style R End Mount.8 / Bore Non Magnetic Piston Standard Mounting: TF, TR, TBE Optional Mounting: TM Optional Porting: /8-7 NPTF.06. DI #0- TP X.5 (MIN) DP / WRENCH FLTS DI 90º 5º #0- TP X.8 (MIN) DP LOCTED ON. DI B.C. ( PER END).8 #0- TP X. DP Standard Mounting: TF Optional Mounting: TR, TBE, TM Optional Porting: /8-7 NPTF #0- TP X. DP / WRENCH FLTS Standard Rx RDx /8 to / in /8" increments.8 Intermediate RHHx /8 to / in /8" increments.06 Heavy RFHx RFHDx /8, /. Standard Rx RDx 7/8 to 6 in /8" increments.8 Intermediate RHHx 5/8 to 6 in /8" increments.06 Heavy RFHx RFHDx /8 to 6 in /8" increments..8 #0- TP X. DP LOCTED ON. DI B.C. ( PLCES).8 #0- TP X. DP THIRD NGLE.06 + STROKE STYLE RD OR RFHD.06 + STROKE STYLE RD OR RFHD 5 www.compactautomation.com (86) 67-95
.8.06. DI #0- TP X.8 (MIN) DP / WRENCH FLTS SENSOR MOUNTING TRCK #0- TP X. DP / WRENCH FLTS DI 90º / Bore Magnetic Piston Standard Rx RDx /8 to / in /8" increments.06 Intermediate RHHx /8, /. Standard Mounting: TF, TR, TBE Optional Mounting: TM Optional Porting: /8-7 NPTF 5º.8 #0- TP X. DP LOCTED ON. DI B.C. ( PER END) Standard Rx RDx 5/8 to 6 in /8" increments.06 Intermediate RHHx /8 to 6 in /8" increments. Heavy RFHx RFHDx /8 to 6 in /8" increments.56 Standard Mounting: TF Optional Mounting: TR, TBE, TM Optional Porting: /8-7 NPTF SENSOR MOUNTING TRCK.8.8 #0- TP X. DP LOCTED ON. DI B.C. ( PLCES) #0- TP X. DP #0- TP X. DP.06 + STROKE STYLE RD.06 + STROKE STYLE RD OR RFHD Style R End Mount THIRD NGLE www.compactautomation.com (86) 67-95 6
Style S End Mount.5 -/8 Bore Non Magnetic Piston Standard S8x SD8x /8 to / in /8" increments.88 Intermediate SHH8x /8 to / in /8" increments. Heavy SFH8x SFHD8x /8 to / in /8" increments.8 Standard Mounting: TF, TR, TBE, TM.8. 0 DI.9. 5/6-8 TP X. (MIN) DP 7/6 WRENCH FLTS Standard Mounting: TF, TR, TBE, TM SQ.9. Standard Mounting: TF Optional Mounting: TR, TBE, TM 5/6-8 TP X.8 DP 7/6 WRENCH FLTS.5 /-0 TP THRU MOUNT FOR #0 SHCS. DI C BORE X.0 DP ( PER END) Standard S8x SD8x 7/8,.88 Intermediate SHH8x 5/8, /. Heavy SFH8x SFHD8x /8, /.8 /-0 TP THRU MOUNT FOR #0 SHCS. DI C BORE X.0 DP ( PER END) Standard S8x SD8x -/8 to 6 in /8" increments.88 Intermediate SHH8x 7/8 to 6 in /8" increments. Heavy SFH8x SFHD8x 5/8 to 6 in /8" increments.8 /-0 TP.5.6.8. + STROKE STYLE SD OR SFHD /8-7 NPTF. (MIN).8.8. + STROKE STYLE SD OR SFHD /8-7 NPTF.8 (MIN) THIRD NGLE. + STROKE STYLE SD OR SFHD 7 www.compactautomation.com (86) 67-95
Standard Mounting: TF, TR, TBE, TM.5.8 Standard Mounting: TF, TR, TBE, TM. 0 DI. 5/6-8 TP X.8 (MIN) DP 7/6 WRENCH FLTS SENSOR MOUNTING TRCK Standard Mounting: TF Optional Mounting: TR, TBE, TM.9 SQ.9. C L -/8 Bore Magnetic Piston Standard S8x SD8x /8 to / in /8" increments. Intermediate SHH8x /8 to / in /8" increments.8 5/6-8 TP X. (MIN) DP 7/6 WRENCH FLTS C L /-0 TP THRU MOUNT FOR #0 SHCS.5 (MIN) /8-7 NPTF SENSOR MOUNTING TRCK. DI C BORE X.0 DP ( PER END) Standard S8x SD8x 5/8, /. Intermediate SHH8x /8, /.8 Heavy SFH8x SFHD8x /8, /.6.88.75 C L C L.9.6.5 /-0 TP THRU MOUNT FOR #0 SHCS. DI C BORE X.0 DP ( PER END) Standard S8x SD8x 7/8 to 6 in /8" increments. Intermediate SHH8x 5/8 to 6 in /8" increments.8 Heavy SFH8x SFHD8x /8 to 6 in /8" increments.6 /-0 TP www.compactautomation.com (86) 67-95.5.8.8. + STROKE STYLE SD OR SFHD.6.8. + STROKE STYLE SD.78 (MIN) /8-7 NPTF THIRD NGLE. + STROKE STYLE SD OR SFHD Style S End Mount 8
Style B Side Mount.5.8 /8-7 NPTF -/8 Bore Non Magnetic Piston..8 0 DI.5 /8-7 NPTF.8.8.5 SQ 5/6-8 TP X. (MIN) DP 7/6 WRENCH FLTS Standard B8x BD8x /8 to / in /8" increments.88 Intermediate BHH8x /8 to / in /8" increments. Heavy BFH8x BFHD8x /8, /.8 5/6-8 TP X.8 DP 7/6 WRENCH FLTS.9.9.8.. Standard B8x BD8x 7/8 to 6 in /8" increments.88 Intermediate BHH8x 5/8 to 6 in /8" increments. Heavy BFH8x BFHD8x /8 to 6 in /8" increments.8.8 #0- TP X. DP #0- TP X. DP ( PLCES) THIRD NGLE. + STROKE STYLE BD OR BFHD.8. + STROKE STYLE BD OR BFHD 9 www.compactautomation.com (86) 67-95
.5.8.8 /8-7 NPTF /8-7 NPTF.8..8 0 DI.5.5 -/8 Bore Magnetic Piston Standard B8x BD8x /8 to / in /8" increments. Intermediate BHH8x /8, /.8 SQ C L 5/6-8 TP X. (MIN) DP 7/6 WRENCH FLTS SENSOR MOUNTING TRCK C L 5/6-8 TP X.8 DP 7/6 WRENCH FLTS.88 C L.9.9.8. SENSOR MOUNTING TRCK Standard B8x BD8x 5/8 to 6 in /8" increments. Intermediate BHH8x /8 to 6 in /8" increments.8 Heavy BFH8x BFHD8x /8 to 6 in /8" increments.6.75 C L.6.9.8. #0- TP X. DP.8 #0- TP X. DP ( PLCES). + STROKE STYLE BD Style B Side Mount THIRD NGLE. + STROKE STYLE BD OR BFHD www.compactautomation.com (86) 67-95 0
Style R End Mount -/8 Bore Non Magnetic Piston Standard Mounting: TF, TR, TBE..8 90º.8 0 DI 5/6-8 TP X. (MIN) DP 7/6 WRENCH FLTS Optional Mounting: TM.88 DI Standard Mounting: TF Optional Mounting: TR, TBE, TM 5/6-8 TP X.8 DP 7/6 WRENCH FLTS Standard R8x RD8x /8 to / in /8" increments.88 Intermediate RHH8x /8 to / in /8" increments. Heavy RFH8x RFHD8x /8, /.8 5º #0- TP X. DP LOCTED ON DI B.C. ( PER END).8 #0- TP X. DP LOCTED ON DI B.C. ( PLCES) /8-7 NPTF Standard R8x RD8x 7/8 to 6 in /8" increments.88 Intermediate RHH8x 5/8 to 6 in /8" increments. Heavy RFH8x RFHD8x /8 to 6 in /8" increments.8.8 /8-7 NPTF. + STROKE STYLE RD OR RFHD. + STROKE STYLE RD OR RFHD THIRD NGLE www.compactautomation.com (86) 67-95
Standard Mounting: TF, TR, TBE..8 90º.8 0 DI 5/6-8 TP X. (MIN) DP 7/6 WRENCH FLTS SENSOR MOUNTING TRCK 5/6-8 TP X.8 DP 7/6 WRENCH FLTS Optional Mounting: TM.88 DI Standard Mounting: TF Optional Mounting: TR, TBE, TM SENSOR MOUNTING TRCK -/8 Bore Magnetic Piston Standard R8x RD8x /8 to / in /8" increments. Intermediate RHH8x /8, /.8 5º #0- TP X. DP LOCTED ON DI B.C. ( PER END).8 #0- TP X. DP LOCTED ON DI B.C. ( PLCES) /8-7 NPTF Standard R8x RD8x 5/8 to 6 in /8" increments. Intermediate RHH8x /8 to 6 in /8" increments.8 Heavy RFH8x RFHD8x /8 to 6 in /8" increments.6.8 /8-7 NPTF. + STROKE STYLE RD. + STROKE STYLE RD OR RFHD Style R End Mount THIRD NGLE www.compactautomation.com (86) 67-95
Style S End Mount. -/8 Bore Non Magnetic Piston Standard S8x SD8x /8 to / in /8" increments. Intermediate SHH8x /8 to / in /8" increments.8 Heavy SFH8x SFHD8x /8, /.6 Standard Mounting: TF, TR, TBE, TM...65 DI... /8-6 TP X. (MIN) DP 9/6 WRENCH FLTS Standard Mounting: TF, TR, TBE, TM /8-6 TP X.88 (MIN) DP 9/6 WRENCH FLTS /8-6 TP X.9 DP 9/6 WRENCH FLTS.75 SQ. Standard Mounting: TF Optional Mounting: TR, TBE, TM..56 (MIN) /-0 TP THRU MOUNT FOR #0 SHCS. DI C BORE X.0 DP ( PER END) Standard S8x SD8x 7/8,. Intermediate SHH8x 5/8, /.8 Heavy SFH8x SFHD8x /8, /.6. /-0 TP.8 THRU MOUNT FOR #0 SHCS. DI C BORE X.0 DP ( PER END) /-0 TP.6... /8-7 NPTF Standard S8x SD8x -/8 to 6 in /8" increments. Intermediate SHH8x 7/8 to 6 in /8" increments.8 Heavy SFH8x SFHD8x 5/8 to 6 in /8" increments.6 www.compactautomation.com (86) 67-95 /8-7 NPTF. + STROKE STYLE SD OR SFHD. + STROKE STYLE SD OR SFHD. + STROKE STYLE SD OR SFHD THIRD NGLE
Standard Mounting: TF, TR, TBE, TM....65 DI... /8-6 TP X (MIN) DP 9/6 WRENCH FLTS SENSOR MOUNTING TRCK Standard Mounting: TF, TR, TBE, TM /8-6 TP X.88 (MIN) DP 9/6 WRENCH FLTS SENSOR MOUNTING TRCK Standard Mounting: TF Optional Mounting: TR, TBE, TM C L -/8 Bore Magnetic Piston Standard S8x SD8x /8 to / in /8" increments.8 Intermediate SHH8x /8, /.6 /8-6 TP X.9 (MIN) DP 9/6 WRENCH FLTS.75 SQ. C L.88 /-0 TP.8 C L.6.. /-0 TP.69 (MIN) THRU MOUNT FOR #0 SHCS. DI C BORE X.0 DP ( PER END) Standard S8x SD8x 5/8, /.8 Intermediate SHH8x /8, /.6 Heavy SFH8x SFHD8x /8, /.88 C L.06.. /-0 TP.8 THRU MOUNT FOR #0 SHCS. DI C BORE X.0 DP ( PER END) Standard S8x SD8x 7/8 to 6 in /8" increments.8 Intermediate SHH8x 5/8 to 6 in /8" increments.6 Heavy SFH8x SFHD8x /8 to 6 in /8" increments.88.6. /8-7 NPTF /8-7 NPTF. + STROKE STYLE SD OR SFHD. + STROKE STYLE SD. + STROKE STYLE SD OR SFHD Style S End Mount THIRD NGLE www.compactautomation.com (86) 67-95
Style B Side Mount.. /8-7 NPTF -/8 Bore Non Magnetic Piston...65 DI.. /8-7 NPTF.. Standard B8x BD8x /8 to / in /8" increments. Intermediate BHH8x /8 to / in /8" increments.8 Heavy BFH8x BFHD8x /8, /.6.75 SQ /8-6 TP X. (MIN) DP 9/6 WRENCH FLTS /8-6 TP X.88 (MIN) DP 9/6 WRENCH FLTS.5.5 Standard B8x BD8x 7/8 to 6 in /8" increments. Intermediate BHH8x 5/8 to 6 in /8" increments.8 Heavy BFH8x BFHD8x /8 to 6 in /8" increments.6.5.5 #0- TP X. DP #0- TP X. DP THIRD NGLE. + STROKE STYLE BD OR BFHD. + STROKE STYLE BD OR BFHD 5 www.compactautomation.com (86) 67-95
.. /8-7 NPTF. /8-7 NPTF.....65 DI..75 SQ C L -/8 Bore Magnetic Piston /8-6 TP X (MIN) DP 9/6 WRENCH FLTS SENSOR MOUNTING TRCK C L /8-6 TP X.88 DP 9/6 WRENCH FLTS Standard B8x BD8x /8 to / in /8" increments.8 Intermediate BHH8x /8, /.6.8.5 C L.5.6 SENSOR MOUNTING TRCK Standard B8x BD8x 5/8 to 6 in /8" increments.8 Intermediate BHH8x /8 to 6 in /8" increments.6 Heavy BFH8x BFHD8x /8 to 6 in /8" increments.88.5 C L.5.06 #0- TP X. DP #0- TP X. DP ( PLCES). + STROKE STYLE BD Style B Side Mount THIRD NGLE. + STROKE STYLE BD OR BFHD www.compactautomation.com (86) 67-95 6
Style R End Mount. -/8 Bore Non Magnetic Piston Standard Mounting: TF, TR, TBE..65 DI /8-6 TP X. (MIN) DP 9/6 WRENCH FLTS Optional Mounting: TM. DI Standard Mounting: TF Optional Mounting: TR, TBE, TM /8-6 TP X.88 (MIN) DP 9/6 WRENCH FLTS 90º Standard R8x RD8x /8 to / in /8" increments. Intermediate RHH8x /8 to / in /8" increments.8 Heavy RFH8x RFHD8x /8, /.6 5º #0- TP X. DP LOCTED ON.75 DI B.C. ( PER END) #0- TP X. DP LOCTED ON.75 DI B.C. ( PLCES).. /8-7 NPTF Standard R8x RD8x 7/8 to 6 in /8" increments. Intermediate RHH8x 5/8 to 6 in /8" increments.8 Heavy RFH8x RFHD8x /8 to 6 in /8" increments.6 /8-7 NPTF. THIRD NGLE. + STROKE STYLE RD OR RFHD. + STROKE STYLE RD OR RFHD 7 www.compactautomation.com (86) 67-95
. Standard Mounting: TF, TR, TBE..65 DI Optional Mounting: TM /8-6 TP X (MIN) DP 9/6 WRENCH FLTS SENSOR MOUNTING TRCK. DI Standard Mounting: TF Optional Mounting: TR, TBE, TM /8-6 TP X.88 (MIN) DP 9/6 WRENCH FLTS 90º SENSOR MOUNTING TRCK -/8 Bore Magnetic Piston Standard R8x RD8x /8 to / in /8" increments.8 Intermediate RHH8x /8, /.6 5º #0- TP X. DP LOCTED ON.75 DI B.C. ( PER END) #0- TP X. DP LOCTED ON.75 DI B.C. ( PLCES).. /8-7 NPTF Standard R8x RD8x 5/8 to 6 in /8" increments.8 Intermediate RHH8x /8 to 6 in /8" increments.6 Heavy RFH8x RFHD8x /8 to 6 in /8" increments.88 /8-7 NPTF.. + STROKE STYLE RD Style R End Mount THIRD NGLE. + STROKE STYLE RD OR RFHD www.compactautomation.com (86) 67-95 8
9 Style S End Mount -5/8 Bore Non Magnetic Piston Standard S58x SD58x /8 to / in /8" increments. Intermediate SHH58x /8 to / in /8" increments.8 Heavy SFH58x SFHD58x /8, /.6 Standard Mounting: TF, TR, TBE, TM.. /8-6 TP X.88 (MIN) DP 9/6 WRENCH FLTS Standard Mounting: TF Optional Mounting: TR, TBE, TM..65 DI.5 /8-6 TP X.9 DP 9/6 WRENCH FLTS.00 SQ.5 /8-6 TP X. (MIN) DP 9/6 WRENCH FLTS Standard Mounting: TF, TR, TBE, TM.. /-0 TP.8 THRU MOUNT FOR #0 SHCS. DI C BORE X.0 DP ( PER END) /-0 TP THRU MOUNT FOR #0 SHCS. DI C BORE X.0 DP ( PER END) Standard S58x SD58x 7/8,. Intermediate SHH58x 5/8, /.8 Heavy SFH58x SFHD58x /8, /.6 Standard S58x SD58x -/8 to 6 in /8" increments. Intermediate SHH58x 7/8 to 6 in /8" increments.8 Heavy SFH58x SFHD58x 5/8 to 6 in /8" increments.6 /-0 TP www.compactautomation.com (86) 67-95.6....56 (MIN) /8-7 NPTF /8-7 NPTF THIRD NGLE. + STROKE STYLE SD OR SFHD. + STROKE STYLE SD OR SFHD. + STROKE STYLE SD OR SFHD
Standard Mounting: TF, TR, TBE, TM....65 DI /8-6 TP X (MIN) DP 9/6 WRENCH FLTS SENSOR MOUNTING TRCK /8-6 TP X.88 (MIN) DP 9/6 WRENCH FLTS SENSOR MOUNTING TRCK Standard Mounting: TF Optional Mounting: TR, TBE, TM.5 /8-6 TP X.9 DP 9/6 WRENCH FLTS.00 SQ.5 C L -5/8 Bore Magnetic Piston Standard S58x SD58x /8 to / in /8" increments.8 Intermediate SHH58x /8, /.6 Standard Mounting: TF, TR, TBE, TM C L /-0 TP THRU MOUNT FOR #0 SHCS. DI C BORE X.0 DP ( PER END) Standard S58x SD58x 5/8, /.8 Intermediate SHH58x /8, /.6 Heavy SFH58x SFHD58x /8, /.88 C L. C L..6...8 /-0 TP THRU MOUNT FOR #0 SHCS. DI C BORE X.0 DP ( PER END) Standard S58x SD58x 7/8 to 6 in /8" increments.8 Intermediate SHH58x 5/8 to 6 in /8" increments.6 Heavy SFH58x SFHD58x /8 to 6 in /8" increments.88 /-0 TP..6...69 (MIN) /8-7 NPTF. + STROKE STYLE SD /8-7 NPTF. + STROKE STYLE SD OR SFHD. + STROKE STYLE SD OR SFHD Style S End Mount THIRD NGLE www.compactautomation.com (86) 67-95 0
Style B Side Mount.. /8-7 NPTF -5/8 Bore Non Magnetic Piston..65 DI..00 SQ. /8-6 TP X. (MIN) DP /-0 TP X.8 DP 9/6 WRENCH FLTS... /8-6 TP X.88 (MIN) DP 9/6 WRENCH FLTS /-0 TP X.8 DP ( PLCES) /8-7 NPTF Standard B58x BD58x /8 to / in /8" increments. Intermediate BHH58x /8 to / in /8" increments.8 Heavy BFH58x BFHD58x /8, /.6.5.5 Standard B58x BD58x 7/8 to 6 in /8" increments. Intermediate BHH58x 5/8 to 6 in /8" increments.8 Heavy BFH58x BFHD58x /8 to 6 in /8" increments.6 THIRD NGLE. + STROKE STYLE BD OR BFHD. + STROKE STYLE BD OR BFHD www.compactautomation.com (86) 67-95
.. /8-7 NPTF. /8-7 NPTF...65 DI..00 SQ -5/8 Bore Magnetic Piston C L. SENSOR MOUNTING TRCK /8-6 TP X (MIN) DP /-0 TP X.8 DP 9/6 WRENCH FLTS. /8-6 TP X.88 (MIN) DP 9/6 WRENCH FLTS SENSOR MOUNTING TRCK C L Standard B58x BD58x /8 to / in /8" increments.8 Intermediate BHH58x /8, /.6 C L.. C L.6.5.5 Standard B58x BD58x 5/8 to 6 in /8" increments.8 Intermediate BHH58x /8 to 6 in /8" increments.6 Heavy BFH58x BFHD58x /8 to 6 in /8" increments.88 /-0 TP X.8 DP ( PLCES). + STROKE STYLE BD Style B Side Mount THIRD NGLE. + STROKE STYLE BD OR BFHD www.compactautomation.com (86) 67-95
Style R End Mount. -5/8 Bore Non Magnetic Piston Standard Mounting: TF, TR, TBE..65 DI Optional Mounting: TM /8-6 TP X. (MIN) DP 9/6 WRENCH FLTS.8 DI Standard Mounting: TF Optional Mounting: TR, TBE, TM /8-6 TP X.88 (MIN) DP 9/6 WRENCH FLTS 90º Standard R58x RD58x /8 to / in /8" increments. Intermediate RHH58x /8 to / in /8" increments.8 Heavy RFH58x RFHD58x /8, /.6 5º #0- TP X. DP LOCTED ON.00 DI B.C. ( PER END) #0- TP X. DP LOCTED ON.00 DI B.C. ( PLCES).. /8-7 NPTF Standard R58x RD58x 7/8 to 6 in /8" increments. Intermediate RHH58x 5/8 to 6 in /8" increments.8 Heavy RFH58x RFHD58x /8 to 6 in /8" increments.6 /8-7 NPTF. THIRD NGLE. + STROKE STYLE RD OR RFHD. + STROKE STYLE RD OR RFHD www.compactautomation.com (86) 67-95
. Standard Mounting: TF, TR, TBE..65 DI /8-6 TP X (MIN) DP 9/6 WRENCH FLTS /8-6 TP X.88 (MIN) DP 9/6 WRENCH FLTS Optional Mounting: TM.8 DI Standard Mounting: TF Optional Mounting: TR, TBE, TM 90º -5/8 Bore Magnetic Piston 5º #0- TP X. DP LOCTED ON.00 DI B.C. ( PER END) SENSOR MOUNTING TRCK Standard R58x RD58x /8 to / in /8" increments.8 Intermediate RHH58x /8, /.6 #0- TP X. DP LOCTED ON.00 DI B.C. ( PLCES).. /8-7 NPTF Standard R58x RD58x 5/8 to 6 in /8" increments.8 Intermediate RHH58x /8 to 6 in /8" increments.6 Heavy RFH58x RFHD58x /8 to 6 in /8" increments.88 SENSOR MOUNTING TRCK. /8-7 NPTF. + STROKE STYLE RD. + STROKE STYLE RD OR RFHD Style R End Mount THIRD NGLE www.compactautomation.com (86) 67-95
5 Style S End Mount.95 (MIN) Bore Non Magnetic Piston Standard Sx SDx /8 to / in /8" increments.5 Intermediate SHHx /8 to / in /8" increments Heavy SFHx SFHDx /8, /.75 Standard Mounting: TF, TR, TBE, TM.58 (MIN). /8-6 TP X.9 DP 9/6 WRENCH FLTS Standard Mounting: TF Optional Mounting: TR, TBE, TM.65 DI.75 SQ.5.00.5.00 /8-6 TP X (MIN) DP 9/6 WRENCH FLTS Standard Mounting: TF, TR, TBE, TM 5/6-8 TP THRU MOUNT FOR / SHCS. DI C BORE X.7 DP ( PER END)..75 5/6-8 TP THRU MOUNT FOR / SHCS. DI C BORE X.7 DP ( PER END) 5/6-8 TP ( PLCES).75.. /8-7 NPTF Standard Sx SDx 7/8 to -/ in /8" increments.5 Intermediate SHHx 5/8 to -/ in /8" increments Heavy SFHx SFHDx /8 to in /8" increments.75 /8-7 NPTF Standard Sx SDx -5/8 to 6 in /8" increments.5 Intermediate SHHx -/8 to 6 in /8" increments Heavy SFHx SFHDx -/8 to 6 in /8" increments.75 www.compactautomation.com (86) 67-95..75. + STROKE STYLE SD OR SFHD. + STROKE STYLE SD OR SFHD. + STROKE STYLE SD OR SFHD THIRD NGLE
Standard Mounting: TF, TR, TBE, TM.95 (MIN).75. /8-6 TP X.9 DP 9/6 WRENCH FLTS SQ.5.00.65 DI.00 /8-6 TP X.69 (MIN) DP.70 (MIN) 9/6 WRENCH FLTS C L 5/6-8 TP THRU MOUNT FOR / SHCS SENSOR. DI C BORE X.7 DP MOUNTING ( PER END) TRCK Standard Mounting: TF Optional Mounting: TR, TBE, TM.5 Standard Mounting: TF, TR, TBE, TM Bore Magnetic Piston Standard Sx SDx /8 to / in /8" increments Intermediate SHHx /8, /.75.75 5/6-8 TP THRU MOUNT FOR / SHCS. DI C BORE X.7 DP ( PER END) C L.56.8 5/6-8 TP ( PLCES)..75 /8-7 NPTF Standard Sx SDx 5/8 to -/ in /8" increments Intermediate SHHx /8 to in /8" increments.75 Heavy SFHx SFHDx /8 to / in /8" increments.00.. /8-7 NPTF Standard Sx SDx -/8 to 6 in /8" increments Intermediate SHHx -/8 to 6 in /8" increments.75 Heavy SFHx SFHDx 7/8 to 6 in /8" increments.00..75. + STROKE STYLE SD. + STROKE STYLE SD OR SFHD. + STROKE STYLE SD OR SFHD Style S End Mount THIRD NGLE www.compactautomation.com (86) 67-95 6
Style B Side Mount..75 Bore Non Magnetic Piston /8-7 NPTF..65 DI..75..75. /8-7 NPTF SQ /8-6 TP X (MIN) DP 9/6 WRENCH FLTS Standard Bx BDx /8 to / in /8" increments.5 Intermediate BHHx /8 to / in /8" increments Heavy BFHx BFHDx /8, /.75 /8-6 TP X.9 DP 9/6 WRENCH FLTS.5.00.5.00 5/6-8 TP X DP Standard Bx BDx 7/8 to 6 in /8" increments.5 Intermediate BHHx 5/8 to 6 in /8" increments Heavy BFHx BFHDx /8 to 6 in /8" increments.75 5/6-8 TP X DP ( PLCES). + STROKE STYLE BD OR BFHD. + STROKE STYLE BD OR BFHD THIRD NGLE 7 www.compactautomation.com (86) 67-95
..75. /8-7 NPTF.75. /8-7 NPTF..75. SQ.65 DI C L /8-6 TP X.69 (MIN) DP 9/6 WRENCH FLTS /8-6 TP X.9 DP 9/6 WRENCH FLTS Bore Magnetic Piston Standard Bx BDx /8 to / in /8" increments Intermediate BHHx /8, /.75 SENSOR MOUNTING TRCK.56 C L.5.8.00.5 Standard Bx BDx 5/8 to 6 in /8" increments Intermediate BHHx /8 to 6 in /8" increments.75 Heavy BFHx BFHDx /8 to 6 in /8" increments.00.00 5/6-8 TP X DP 5/6-8 TP X DP ( PLCES). + STROKE STYLE BD. + STROKE STYLE BD OR BFHD Style B Side Mount THIRD NGLE www.compactautomation.com (86) 67-95 8
Style R End Mount. Bore Non Magnetic Piston Standard Mounting: TF, TR, TBE..65 DI Optional Mounting: TM /8-6 TP X (MIN) DP 9/6 WRENCH FLTS.00 DI Standard Mounting: TF Optional Mounting: TR, TBE, TM /8-6 TP X.9 DP 9/6 WRENCH FLTS 90º Standard Rx RDx /8 to / in /8" increments.5 Intermediate RHHx /8 to / in /8" increments Heavy RFHx RFHDx /8, /.75 5º /-0 TP X.6 DP LOCTED ON DI B.C. ( PER END) /-0 TP X.6 DP LOCTED ON DI B.C. ( PLCES).. /8-7 NPTF Standard Rx RDx 7/8 to 6 in /8" increments.5 Intermediate RHHx 5/8 to 6 in /8" increments Heavy RFHx RFHDx /8 to 6 in /8" increments.75 /8-7 NPTF. THIRD NGLE. + STROKE STYLE RD OR RFHD. + STROKE STYLE RD OR RFHD 9 www.compactautomation.com (86) 67-95
. Standard Mounting: TF, TR, TBE..65 DI /8-6 TP X.69 (MIN) DP 9/6 WRENCH FLTS /8-6 TP X.9 (MIN) DP 9/6 WRENCH FLTS Optional Mounting: TM.00 DI Standard Mounting: TF Optional Mounting: TR, TBE, TM 90º SENSOR MOUNTING TRCK SENSOR MOUNTING TRCK Bore Magnetic Piston Standard Rx RDx /8 to / in /8" increments Intermediate RHHx /8, /.75 5º /-0 TP X.6 DP LOCTED ON DI B.C. ( PER END) /-0 TP X.6 DP LOCTED ON DI B.C. ( PLCES).. /8-7 NPTF Standard Rx RDx 5/8 to 6 in /8" increments Intermediate RHHx /8 to 6 in /8" increments.75 Heavy RFHx RFHDx /8 to 6 in /8" increments.00. /8-7 NPTF. + STROKE STYLE RD. + STROKE STYLE RD OR RFHD Style R End Mount THIRD NGLE www.compactautomation.com (86) 67-95 50
5 Style S End Mount.69 (MIN) -/ Bore Non Magnetic Piston Standard Sx SDx /8 to / in /8" increments.8 Intermediate SHHx /8 to / in /8" increments.6 Heavy SFHx SFHDx /8, /.88 Standard Mounting: TF, TR, TBE, TM..750 DI...8 /- TP X (MIN) DP /6 WRENCH FLTS Standard Mounting: TF, TR, TBE, TM.00 SQ.8 Standard Mounting: TF Optional Mounting: TR, TBE, TM.9 /- TP X.5 DP /6 WRENCH FLTS.75 /8-6 TP THRU MOUNT FOR 5/6 SHCS DI C BORE X. DP ( PER END) Standard Sx SDx 7/8 to -/ in /8" increments.8 Intermediate SHHx 5/8 to -/ in /8" increments.6 Heavy SFHx SFHDx /8 to in /8" increments.88 /8-6 TP ( PLCES).75 /8-7 NPTF.06 (MIN) /- TP X.00 (MIN) DP /8-6 TP /8-7 NPTF /6 WRENCH FLTS THRU MOUNT FOR 5/6 SHCS DI C BORE X. DP ( PER END) Standard Sx SDx -5/8 to 6 in /8" increments.8 Intermediate SHHx -/8 to 6 in /8" increments.6 Heavy SFHx SFHDx -/8 to 6 in /8" increments.88 www.compactautomation.com (86) 67-95.75 THIRD NGLE. + STROKE STYLE SD OR SFHD. + STROKE STYLE SD OR SFHD. + STROKE STYLE SD OR SFHD
Standard Mounting: TF, TR, TBE, TM.8 (MIN).06 (MIN).9..750 DI /- TP X.6 (MIN) DP /6 WRENCH FLTS /- TP X.00 (MIN) DP /6 WRENCH FLTS Standard Mounting: TF Optional Mounting: TR, TBE, TM..8. Standard Mounting: TF, TR, TBE, TM /- TP X.5 DP /6 WRENCH FLTS.00 SQ.8 C L SENSOR MOUNTING TRCK -/ Bore Magnetic Piston Standard Sx SDx /8 to / in /8" increments.6 Intermediate SHHx /8, /.88 /8-6 TP THRU MOUNT FOR 5/6 SHCS DI C BORE X. DP ( PER END) Standard Sx SDx 5/8 to -/ in /8" increments.6 Intermediate SHHx /8 to in /8" increments.88 Heavy SFHx SFHDx /8 to / in /8" increments..8 C L..75 /8-6 TP THRU MOUNT FOR 5/6 SHCS DI C BORE X. DP ( PER END) Standard Sx SDx -/8 to 6 in /8" increments.6 Intermediate SHHx -/8 to 6 in /8" increments.88 Heavy SFHx SFHDx 7/8 to 6 in /8" increments. /8-6 TP ( PLCES).75 /8-7 NPTF /8-7 NPTF. + STROKE STYLE SD.75. + STROKE STYLE SD OR SFHD. + STROKE STYLE SD OR SFHD Style S End Mount THIRD NGLE www.compactautomation.com (86) 67-95 5
Style B Side Mount -/ Bore Non Magnetic Piston Optional Porting: /-8 NPTF.75 /8-7 NPTF..750 DI.75 Optional Porting: /-8 NPTF /8-7 NPTF.75.00 SQ /- TP X (MIN) DP /6 WRENCH FLTS Standard Bx BDx /8 to / in /8" increments.8 Intermediate BHHx /8 to / in /8" increments.6 Heavy BFHx BFHDx /8, /.88 Standard Bx BDx 7/8 to 6 in /8" increments.8 Intermediate BHHx 5/8 to 6 in /8" increments.6 Heavy BFHx BFHDx /8 to 6 in /8" increments.88 /- TP X.00 (MIN) DP /6 WRENCH FLTS.5.5 5/6-8 TP X.6 DP 5/6-8 TP X.6 DP ( PLCES) THIRD NGLE. + STROKE STYLE BD OR BFHD. + STROKE STYLE BD OR BFHD 5 www.compactautomation.com (86) 67-95
Optional Porting: /-8 NPTF.75 Optional Porting: /-8 NPTF /8-7 NPTF /8-7 NPTF.75..750 DI.75.00 SQ -/ Bore Magnetic Piston Standard Bx BDx /8 to / in /8" increments.6 Intermediate BHHx /8, /.88 C L /- TP X.6 (MIN) DP /6 WRENCH FLTS /- TP X.00 (MIN) DP /6 WRENCH FLTS SENSOR MOUNTING TRCK.8 C L. Standard Bx BDx 5/8 to 6 in /8" increments.6 Intermediate BHHx /8 to 6 in /8" increments.88 Heavy BFHx BFHDx /8 to 6 in /8" increments..5.5 5/6-8 TP X.6 DP 5/6-8 TP X.6 DP ( PLCES). + STROKE STYLE BD. + STROKE STYLE BD OR BFHD Style B Side Mount THIRD NGLE www.compactautomation.com (86) 67-95 5
Style R End Mount -/ Bore Non Magnetic Piston Standard Mounting: TF, TR, TBE Optional Mounting: TM Optional Porting: /-8 NPTF..750 DI /- TP X (MIN) DP /6 WRENCH FLTS DI 90º 5º /-0 TP X.6 DP LOCTED ON.00 DI B.C. ( PER END) /8-7 NPTF Standard Mounting: TF Optional Mounting: TR, TBE, TM Optional Porting: /-8 NPTF /- TP X.00 (MIN) DP /6 WRENCH FLTS Standard Rx RDx /8 to / in /8" increments.8 Intermediate RHHx /8 to / in /8" increments.6 Heavy RFHx RFHDx /8, /.88 Standard Rx RDx 7/8 to 6 in /8" increments.8 Intermediate RHHx 5/8 to 6 in /8" increments.6 Heavy RFHx RFHDx /8 to 6 in /8" increments.88 /-0 TP X.6 DP LOCTED ON.00 DI B.C. ( PLCES) /8-7 NPTF. + STROKE STYLE RD OR RFHD. + STROKE STYLE RD OR RFHD THIRD NGLE 55 www.compactautomation.com (86) 67-95
Style R /- TP X.00 (MIN) DP /6 WRENCH FLTS SENSOR MOUNTING TRCK -/ Bore Magnetic Piston Standard Mounting: TF, TR, TBE Optional Mounting: TM Optional Porting: /-8 NPTF..750 DI /- TP X.6 (MIN) DP /6 WRENCH FLTS DI Standard Mounting: TF Optional Mounting: TR, TBE, TM Optional Porting: /-8 NPTF 90º Standard Rx RDx /8 to / in /8" increments.6 Intermediate RHHx /8, /.88 5º /-0 TP X.6 DP LOCTED ON.00 DI B.C. ( PER END) SENSOR MOUNTING TRCK /-0 TP X.6 DP LOCTED ON.00 DI B.C. ( PLCES) /8-7 NPTF Standard Rx RDx 5/8 to 6 in /8" increments.6 Intermediate RHHx /8 to 6 in /8" increments.88 Heavy RFHx RFHDx /8 to 6 in /8" increments. /8-7 NPTF. + STROKE STYLE RD. + STROKE STYLE RD OR RFHD www.compactautomation.com (86) 67-95 End Mount THIRD NGLE 56
57 Style S End Mount.8 (MIN) Bore Non Magnetic Piston Standard Sx SDx /8 to / in /8" increments.6 Intermediate SHHx /8 to / in /8" increments.88 Heavy SFHx SFHDx /8, /. Standard Mounting: TF, TR, TBE, TM.9 (MIN)..750 DI..88. /- TP X (MIN) DP /6 WRENCH FLTS Optional Porting: /-8 NPTF DI.88 Standard Mounting: TF, TR, TBE, TM Optional Porting: /-8 NPTF.8 /8-6 TP THRU MOUNT FOR 5/6 SHCS DI C BORE X. DP ( PER END).56.56 /8-7 NPTF Standard Sx SDx 7/8 to -/ in /8" increments.6 Intermediate SHHx 5/8 to -/ in /8" increments.88 Heavy SFHx SFHDx /8 to in /8" increments. Standard Mounting: TF Optional Mounting: TR, TBE, TM Optional Porting: /-8 NPTF.9 /- TP X.00 (MIN) DP /6 WRENCH FLTS /- TP X.5 DP /6 WRENCH FLTS /8-6 TP THRU MOUNT FOR 5/6 SHCS DI C BORE X. DP ( PER END) /8-6 TP ( PLCES).8.56.56 /8-7 NPTF Standard Sx SDx -5/8 to 6 in /8" increments.6 Intermediate SHHx -/8 to 6 in /8" increments.88 Heavy SFHx SFHDx -/8 to 6 in /8" increments. www.compactautomation.com (86) 67-95.8. + STROKE STYLE SD OR SFHD. + STROKE STYLE SD OR SFHD. + STROKE STYLE SD OR SFHD THIRD NGLE
Standard Sx SDx /8 to / in /8" increments.88 Intermediate SHHx /8, /. Standard Mounting: TF, TR, TBE, TM.9 (MIN).9 (MIN).9..750 DI..88 /- TP X.6 (MIN) DP /6 WRENCH FLTS /- TP X.00 (MIN) DP /6 WRENCH FLTS /- TP X.5 (MIN) DP /6 WRENCH FLTS Optional Porting: /-8 NPTF. SQ.88 Bore Magnetic Piston.8 /8-6 TP THRU MOUNT FOR 5/6 SHCS DI C BORE X. DP ( PER END) /8-6 TP ( PLCES).56.56 /8-7 NPTF Standard Mounting: TF Optional Mounting: TR, TBE, TM Optional Porting: /-8 NPTF C L SENSOR MOUNTING TRCK Standard Mounting: TF, TR, TBE, TM Optional Porting: /-8 NPTF C L.06.8.8 /8-6 TP THRU MOUNT FOR 5/6 SHCS DI C BORE X. DP ( PER END).56 /8-7 NPTF Standard Sx SDx 5/8 to -/ in /8" increments.88 Intermediate SHHx /8 to in /8" increments. Heavy SFHx SFHDx /8 to / in /8" increments.8 Standard Sx SDx -/8 to 6 in /8" increments.88 Intermediate SHHx -/8 to 6 in /8" increments. Heavy SFHx SFHDx 7/8 to 6 in /8" increments.8.8.56. + STROKE STYLE SD. + STROKE STYLE SD OR SFHD. + STROKE STYLE SD OR SFHD Style S End Mount THIRD NGLE www.compactautomation.com (86) 67-95 58
Style B Side Mount.8 Bore Non Magnetic Piston Optional Porting: /-8 NPTF.56 /8-7 NPTF..750 DI.56.8 Optional Porting: /-8 NPTF.56.56 /8-7 NPTF.8 Standard Bx BDx /8 to / in /8" increments.6 Intermediate BHHx /8 to / in /8" increments.88 Heavy BFHx BFHDx /8, /. SQ /- TP X (MIN) DP /6 WRENCH FLTS Standard Bx BDx 7/8 to 6 in /8" increments.6 Intermediate BHHx 5/8 to 6 in /8" increments.88 Heavy BFHx BFHDx /8 to 6 in /8" increments. /- TP X.00 (MIN) DP /6 WRENCH FLTS...6.88.6.88 /8-6 TP X.75 DP.6 /8-6 TP X.75 DP ( PLCES) THIRD NGLE. + STROKE STYLE BD OR BFHD. + STROKE STYLE BD OR BFHD 59 www.compactautomation.com (86) 67-95
Optional Porting: /-8 NPTF.8.56.56 /8-7 NPTF Optional Porting: /-8 NPTF.56 /8-7 NPTF.8..56.750 DI.8 Standard Bx BDx /8 to / in /8" increments.88 Intermediate BHHx /8, /. SQ /- TP X.00 DP /6 WRENCH FLTS C L /- TP X.6 (MIN) DP /6 WRENCH FLTS Bore Magnetic Piston SENSOR MOUNTING TRCK.06 C L.8 Standard Bx BDx 5/8 to 6 in /8" increments.88 Intermediate BHHx /8 to 6 in /8" increments. Heavy BFHx BFHDx /8 to 6 in /8" increments.8..6.88..6.88 /8-6 TP X.75 DP.6 /8-6 TP X.75 DP ( PLCES). + STROKE STYLE BD. + STROKE STYLE BD OR BFHD Style B Side Mount THIRD NGLE www.compactautomation.com (86) 67-95 60
Style R End Mount.56 Bore Non Magnetic Piston Standard Mounting: TF, TR, TBE Optional Mounting: TM Optional Porting: /-8 NPTF..750 DI /- TP X (MIN) DP /6 WRENCH FLTS.00 DI 90º 5º 5/6-8 TP X.8 DP LOCTED ON DI B.C. ( PER END).56 /8-7 NPTF Standard Mounting: TF Optional Mounting: TR, TBE, TM Optional Porting: /-8 NPTF /- TP X.00 (MIN) DP /6 WRENCH FLTS Standard Rx RDx /8 to / in /8" increments.6 Intermediate RHHx /8 to / in /8" increments.88 Heavy RFHx RFHDx /8, /. Standard Rx RDx 7/8 to 6 in /8" increments.6 Intermediate RHHx 5/8 to 6 in /8" increments.88 Heavy RFHx RFHDx /8 to 6 in /8" increments. 5/6-8 TP X.8 DP LOCTED ON DI B.C. ( PLCES).56.56 /8-7 NPTF. + STROKE STYLE RD OR RFHD. + STROKE STYLE RD OR RFHD THIRD NGLE 6 www.compactautomation.com (86) 67-95
SENSOR MOUNTING TRCK /- TP X.00 (MIN) DP /6 WRENCH FLTS 5/6-8 TP X.8 DP LOCTED ON DI B.C. ( PLCES) Bore Magnetic Piston Standard Mounting: TF, TR, TBE Optional Mounting: TM Optional Porting: /-8 NPTF.56..750 DI /- TP X.6 (MIN) DP /6 WRENCH FLTS.00 DI Standard Mounting: TF Optional Mounting: TR, TBE, TM Optional Porting: /-8 NPTF 90º SENSOR MOUNTING TRCK Standard Rx RDx /8 to / in /8" increments.88 Intermediate RHHx /8, /. 5º 5/6-8 TP X.8 DP LOCTED ON DI B.C. ( PER END).56.56 /8-7 NPTF Standard Rx RDx 5/8 to 6 in /8" increments.88 Intermediate RHHx /8 to 6 in /8" increments. Heavy RFHx RFHDx /8 to 6 in /8" increments.8.56 /8-7 NPTF. + STROKE STYLE RD. + STROKE STYLE RD OR RFHD Style R End Mount THIRD NGLE www.compactautomation.com (86) 67-95 6
Style R End Mount.66 Bore Non Magnetic Piston Standard Mounting: TF, TR, TBE Optional Mounting: TM Optional Porting: /-8 NPTF..750 DI /- TP X.6 (MIN) DP /6 WRENCH FLTS 5.00 DI 90º 5º 5/6-8 TP X.8 DP LOCTED ON DI B.C. ( PER END).66 /8-7 NPTF Standard Mounting: TF Optional Mounting: TR, TBE, TM Optional Porting: /-8 NPTF /- TP X.00 (MIN) DP /6 WRENCH FLTS Standard Rx RDx /8 to / in /8" increments.75 Intermediate RHHx /8 to / in /8" increments.00 Heavy RFHx RFHDx /8, /.5 Standard Rx RDx 7/8 to 6 in /8" increments.75 Intermediate RHHx 5/8 to 6 in /8" increments.00 Heavy RFHx RFHDx /8 to 6 in /8" increments.5 5/6-8 TP X.8 DP LOCTED ON DI B.C. ( PLCES).66.66 /8-7 NPTF. + STROKE STYLE RD OR RFHD. + STROKE STYLE RD OR RFHD THIRD NGLE 6 www.compactautomation.com (86) 67-95
SENSOR MOUNTING TRCK /- TP X.00 (MIN) DP /6 WRENCH FLTS Bore Magnetic Piston Standard Mounting: TF, TR, TBE Optional Mounting: TM Optional Porting: /-8 NPTF.66..750 DI /- TP X.75 (MIN) DP /6 WRENCH FLTS 5.00 DI Standard Mounting: TF Optional Mounting: TR, TBE, TM Optional Porting: /-8 NPTF 90º Standard Rx RDx /8 to / in /8" increments.00 Intermediate RHHx /8, /.5 SENSOR MOUNTING TRCK 5º 5/6-8 TP X.8 DP LOCTED ON DI B.C. ( PER END) Standard Rx RDx 5/8 to 6 in /8" increments.00 Intermediate RHHx /8 to 6 in /8" increments.5 Heavy RFHx RFHDx /8 to 6 in /8" increments 5/6-8 TP X.8 DP LOCTED ON DI B.C. ( PLCES).66.66 /8-7 NPTF.66 /8-7 NPTF. + STROKE STYLE RD. + STROKE STYLE RD OR RFHD Style R End Mount THIRD NGLE www.compactautomation.com (86) 67-95 6
Style R End Mount.67 5 Bore Non Magnetic Piston Standard Mounting: TF, TR, TBE Optional Mounting: TM Optional Porting: /-8 NPTF. B DI C TP 6.00 DI 90º 5º 5/6-8 TP X.8 DP LOCTED ON 5 DI B.C. ( PER END) Standard Mounting: TF Optional Mounting: TR, TBE, TM Optional Porting: /-8 NPTF B DI B C Standard R5x RD5x /8 to / in /8" increments.88.750 Intermediate RHH5x /8 to / in /8" increments..750 Heavy RFH5x RFHD5x /8, /.8.000 C TP 5/6-8 TP X.8 DP LOCTED ON 5 DI B.C. ( PLCES).67.67 /8-7 NPTF B C Standard R5x RD5x 7/8 to 6 in /8" increments.88.750 Intermediate RHH5x 5/8 to 6 in /8" increments..750 Heavy RFH5x RFHD5x /8 to 6 in /8" increments.8.000 /- x.6 (Min.) Dp /6 Wrench Flats /- x.75 (Min.) Dp /6 Wrench Flats 5/8-8 x.88 (Min.) Dp 5/6 Wrench Flats /- x..00 (Min.) Dp /6 Wrench Flats /- x.00 (Min.) Dp /6 Wrench Flats 5/8-8 x.00 (Min.) Dp 5/6 Wrench Flats.67 /8-7 NPTF THIRD NGLE. + STROKE STYLE RD OR RFHD. + STROKE STYLE RD OR RFHD 65 www.compactautomation.com (86) 67-95
B DI SENSOR MOUNTING TRCK C TP 5 Bore Magnetic Piston Standard Mounting: TF, TR, TBE Optional Mounting: TM Optional Porting: /-8 NPTF.67. B DI C TP B C Standard R5x RD5x /8 to / in /8" increments..750 Intermediate RHH5x /8, /.8.750 6.00 DI Standard Mounting: TF Optional Mounting: TR, TBE, TM Optional Porting: /-8 NPTF 90º SENSOR MOUNTING TRCK 5º 5/6-8 TP X.8 DP LOCTED ON 5 DI B.C. ( PER END) 5/6-8 TP X.8 DP LOCTED ON 5 DI B.C. ( PLCES).67.67 /8-7 NPTF B C Standard R5x RD5x 5/8 to 6 in /8" increments..750 Intermediate RHH5x /8 to 6 in /8" increments.8.750 Heavy RFH5x RFHD5x /8 to 6 in /8" increments.6.000 /- x.75 (Min.) Dp /6 Wrench Flats /- x.88 (Min.) Dp /6 Wrench Flats.67 /8-7 NPTF. + STROKE STYLE RD /- x..00 (Min.) Dp /6 Wrench Flats /- x.00 (Min.) Dp /6 Wrench Flats 5/8-8 x 88 (Min.) Dp 5/6 Wrench Flats. + STROKE STYLE RD OR RFHD Style R End Mount THIRD NGLE www.compactautomation.com (86) 67-95 66
Style R End Mount.78 6 Bore Non Magnetic Piston Standard Mounting: TF, TR, TBE Optional Mounting: TM Optional Porting: /-8 NPTF..00 DI 5/8-8 TP X.9 DP 5/6 WRENCH FLTS 7.00 DI 90º 5º 5/6-8 TP X.8 DP LOCTED ON 6 DI B.C. ( PER END).78 /8-7 NPTF Standard Mounting: TF Optional Mounting: TR, TBE, TM Optional Porting: /-8 NPTF 5/8-8 TP X.5 DP 5/6 WRENCH FLTS Standard R6x RD6x /8 to / in /8" increments. Standard R6x RD6x 5/8 to 6 in /8" increments. 5/6-8 TP X.8 DP LOCTED ON 6 DI B.C. ( PLCES).78.78 /8-7 NPTF. + STROKE STYLE RD. + STROKE STYLE RD THIRD NGLE 67 www.compactautomation.com (86) 67-95
SENSOR MOUNTING TRCK 5/8-8 TP X.5 DP 5/6 WRENCH FLTS 6 Bore Magnetic Piston Standard Mounting: TF, TR, TBE Optional Mounting: TM Optional Porting: /-8 NPTF.78..00 DI 5/8-8 TP X.9 DP 5/6 WRENCH FLTS Standard R6x RD6x /8, /.8 7.00 DI Standard Mounting: TF Optional Mounting: TR, TBE, TM Optional Porting: /-8 NPTF 90º SENSOR MOUNTING TRCK 5/6-8 TP X.8 DP LOCTED ON 6 DI B.C. ( PLCES) 5º 5/6-8 TP X.8 DP LOCTED ON 6 DI B.C. ( PER END) Standard R6x RD6x /8 to 6 in /8" increments.8.78.78.78 /8-7 NPTF /8-7 NPTF. + STROKE STYLE RD. + STROKE STYLE RD Style R End Mount THIRD NGLE www.compactautomation.com (86) 67-95 68
Style R End Mount 8 Bore Non Magnetic Piston Standard Mounting: TF, TR, TBE Optional Mounting: TM Optional Porting: /-8 NPTF.78..00 DI 5/8-8 TP X.9 DP 5/6 WRENCH FLTS 9.00 DI 60º 5º.78 50º /8-7 NPTF 5/6-8 TP X.78 DP LOCTED ON 8 DI B.C. (6 PER END) Standard Mounting: TF Optional Mounting: TR, TBE, TM Optional Porting: /-8 NPTF 5/8-8 TP X.5 DP 5/6 WRENCH FLTS Standard R8x RD8x /8 to / in /8" increments.8 Standard R8x RD8x 5/8 to 6 in /8" increments.8 5/6-8 TP X.78 DP LOCTED ON 8 DI B.C. (6 PLCES).78.78 /8-7 NPTF. + STROKE STYLE RD. + STROKE STYLE RD THIRD NGLE 69 www.compactautomation.com (86) 67-95
Style R SENSOR MOUNTING TRCK 5/8-8 TP X.5 DP 5/6 WRENCH FLTS 65º 5/6-8 TP X.78 DP LOCTED ON 8 DI B.C. (6 PLCES) 8 Bore Magnetic Piston Standard Mounting: TF, TR, TBE Optional Mounting: TM Optional Porting: /-8 NPTF.78..00 DI 5º 5/8-8 TP X.9 DP 5/6 WRENCH FLTS 9.00 DI Standard Mounting: TF Optional Mounting: TR, TBE, TM Optional Porting: /-8 NPTF 60º Standard R8x RD8x /8, /.6 SENSOR MOUNTING TRCK 5º 05º.78.78 5/6-8 TP X.78 DP LOCTED ON 8 DI B.C. (6 PER END) /8-7 NPTF Standard R8x RD8x /8 to 6 in /8" increments.6.78 /8-7 NPTF. + STROKE STYLE RD. + STROKE STYLE RD www.compactautomation.com (86) 67-95 End Mount THIRD NGLE 70
Seal Descriptions Conversion Formula: Cº = (Fº - º) x 5/9 Type Ordering Suffix Nitrile Fluorocarbon PTFE* Ethylene Propylene Nitrile* Fluorocarbon* HTV CRT ETP HYD VHYD *vailable through bore only Rating 0 to 00 F -8 to 9 C 0 to 00 F -8 to 0 C 50 to 00 F to 0 C -70 to 00 F -57 to 50 C 0 to 50 F -8 to C 0 to 00 F -8 to 0 C Pneumatic Seals Description Most commonly used elastomer O-ring due to its excellent resistance to petroleum products, wear, tear and friction. Works with lubricated or non-lubricated air in the noted temperature range. Recommended for general purpose sealing with petroleum oils and fluids, water and silicone greases and oils. Used mainly for elevated temperatures, harsh environments where some coolants, solvents, cleaning agents or other chemicals will contact the seal gland. Lower compression set is characteristic. For your specific requirements, consult factory. Specified for extreme temperatures and harsh atmosphere where rubber seals are not suitable. Best compression set is at high temperature. PTFE seals are not guaranteed to be leak free and higher breakaway is typical. Overall strength does not compare favorably to rubber in abrasion resistance. Used for sealing water, phosphate-ester hydraulic fluids, glycol base brake fluids, silicone oils and grease, many acids, solvents. Not compatible with mineral oil products. Consult factory for specific applications. Hydraulic Seals Seal material is Nitrile and Urethane. Moderate resistance to abrasion, high pressure and shock. Low temperature decreases flexibility. Recommended for hydraulic fluids, dilute acids, and water. Seal material is fluorocarbon and PTFE. This option is designed to operate over an extremely wide elevated temperature range, harsh environment or with any non-oil based synthetic hydraulic fluids. 7 www.compactautomation.com (86) 67-95
Corrosion Resistant 00 Series Stainless Steel Standard Features: 00% 00 series stainless steel components interior and exterior Viton seals (Teflon seals, suffix CRT, are optional) Plastic rod bearings Intermediate and Heavy Features: 00% 00 series stainless steel components interior and exterior Viton seals (Teflon seals, suffix CRT, are optional) UHMW plastic rod bearings Optional - Crystalline PET Thermoplastic Polyester rod bearing is available for use in clean-room environments. Consult Factory for details. Magnetic Piston Cylinders: Bolt-on Mounting Track is aluminum only Ordering: Specify CR before cylinder part number vailable on / through Delivery: Non-standard delivery, consult factory djustable Retract Stroke Bore B /.56 /-0 -/8 -/8-5/8 -/ 5 6 8.75 /8-6.00 /-.8 /-0 LOCKNUT DI THRED SEL SET SCREW STOP B DO NOT use with any pivoting applications / - Bore Options RER ENDCP LENGTH VRIES WITH DJUSTMENT CR Ordering Prefix: CR Bore: / - Material: 00 Series stainless steel Stroke: /8 - in /8 increments DJ pplications: Chemical / Petroleum Medical Equipment Salt Water Exposure Clean Rooms Food Processing Electronic ssembly Nuclear Pharmaceutical THIRD NGLE Specify Length Ordering Suffix: DJ_ Length: /8 - in /8 increments Rod: Single only Temperature: 00ºF Max. Material: luminum endcap, steel locknut and thread seal ll dimensions are in inches unless otherwise noted. ll Styles www.compactautomation.com (86) 67-95 7
7 ll Styles / - Bore Options Urethane Bumper Pads UB- BUMPERS ON FRONT END Urethane Cushion Pads UC- CUSHION PDS ON FRONT END UB- BUMPERS ON BOTH ENDS Designed for noise reduction and minor piston impact only Cylinder length does not increase Stroke is decreased by /8 per bumper Bumper Pads mechanically retained within the endcap Repairable part - replaceable bumper pads UC- CUSHION PDS ON BOTH ENDS Designed for noise reduction and minor piston impact only Cylinder length does not increase Cushion Pads mechanically retained within the endcap Repairable part - replaceable cushion pads UB- BUMPERS ON RER END UC- CUSHION PDS ON RER END www.compactautomation.com (86) 67-95 UB Example: UB, UB, UB Ordering Suffix: UB_ Bore: / - Temperature: 0º - 50ºF Service: Pneumatic only Material: Polyurethane This option does not replace external shock absorbers needed for high loads. UC THIRD NGLE NOTE: UB not available with CR or NR option Example: UC, UC, UC Ordering Suffix: UC_ Bore: / - Temperature: 0º - 50ºF Service: Pneumatic only Material: Polyurethane NOTE: UC not available with CR or NR option This option does not replace external shock absorbers needed for high loads. ll dimensions are in inches unless otherwise noted.
Positive lignment Pocket The alignment pocket and pilot are designed to fit between the cylinder and the mounting surface. This ensures accurate mounting and added shear strength. S STYLE DI X B DP R STYLE Positive lignment sold separately B +.000 C DI -.00 Dual Diameter.08 +.000 -.00 D DI Bore B C D -/8 -/8-5/8 PL8-05.7.09.5 PL8-07.9.. PL58-07.9...6 PL58-.9..6 Bore B /.. -/8. -/8-5/8.6.9 -/ 5 6 8 C L.75.5. / - 8 Bore Options Common Diameter +.000 -.00 B DI Bore B / PLL.0. -/8 PL8L.0 -/8-5/8 PL58L.0.6 -/ 5 6 8 PLL..75 PLL P Ordering Suffix: P Style: S and R only Rod: Single only Provides positive means of locating cylinder centerline within.005 PL : Rod: Material: Styles S & R THIRD NGLE PL_ Single only Stainless steel www.compactautomation.com (86) 67-95 ll dimensions are in inches unless otherwise noted. 7
75 ll Styles Hollow Rod / - 8 Bore Options Our hollow rod option is available for applications that require passage through a double ended rod. HR S TP T DRILL THRU TPPED ON BOTH ENDS OF ROD WITH DRILL THRU HR S TP T DRILL THRU HR HR Bore S Tap T Drill Thru S Tap T Drill Thru / #0- x /8 Dp.. -/8 5/6-8 x 5/8 Dp..5 #0- x /8 Dp.6 -/8-5/8 /8-6 x / Dp.. /8-7 NPTF. Rod End Extension EX_ Modifications Welcome Special stroke lengths, port orientation, mounting configuration. SINGLE ROD END ll dimensions are in inches unless otherwise noted. EXD_ For special extension or length - consult factory Not a screw on component Female tap does not change DOUBLE ROD END EXD_ Extended equally at both ends HR Ordering Suffix: HR_ Bore: / - only : Standard and Full Husky only TPPED ON BOTH ENDS OF ROD FOR FITTING Rod: Double only WITH DRILL THRU Service: Pneumatic only Stroke: /8 - in /8 increments pplications Example YES NO Gases Liquids Vacuum Specify Length Linear / Rotary Cylinder Clamp and Punch Cylinder Blow Molding Cylinder Hydraulic Cylinders Non-Rotating Rods SPECILS: Consult factory with ID requirements, thread information, pipe taps, etc. EXF_ www.compactautomation.com (86) 67-95 DOUBLE ROD END End EX Specify Length Extension Front End EXF Specify Length EXR_ THIRD NGLE X X End EXD Specify Length Extension Rear End EXR Specify Length Ordering Suffix: EX, EXD, EXF or EXR Length: /8 - in /8 increments
Clevis Bracket / Set Screw D Male Stud CORSE OR FINE THREDS (FT) B SQ C H G E J THRED THRED LENGTH Double ended unit has stud in front end only. If male stud is desired on both ends, specify MSD or FTMSD. Male stud thread: Same pitch and diameter as female rod tap B F DI PIN K / - 8 Bore Options CBSS_ Specify Screw Length Bore B C D E F G H J K Screw Length Standard Optional /.69.8..5.9.9.88 #0-. / -/8.8.6..56..5.5.00 5/6-8. / -/8-5/8.00.75..69.8... /8-6. / Up to -/ " in /8".5.00.5.8.8.8.8 /-.7 increments 5 FH5 6 8..00.66.06.00.75.00.00 5/8-8.8 -/ Bore MIN MX /.8 B.06 -/8.6. -/8-5/8.75. -/ 5 6 8.00. www.compactautomation.com (86) 67-95 Ordering Suffix: CBSS_ Material: Steel black oxide with case hardened pin and clips Example: CBSS78 = 7/8 screw length Coarse thread MS Fine thread FTMS THIRD NGLE Ordering Suffix: MS or FTMS Material: Steel black oxide Length: Specify length ll dimensions are in inches unless otherwise noted. ll Styles 76
77 ll Styles Rod Eye Rod Wiper ROD WIPER / - 8 Bore Options ROD END CP SQ Bore B C D E F G /.8.8.9..9.9 #0-.8.88.69..9.9 #0- -/8.5.0.5.5 5/6-8 -/8-5/8.6.6.... /8-8 -/ 5 FH5 6 8.00.00.88 /-.00.00.88 /-.75.9.75.75 5/8-8 E F DI Husky duty only Cylinder length does not increase Positioned below cylinder face B C D G THRED RES - Short Head Design RE - Standard Design www.compactautomation.com (86) 67-95 RE(S) Ordering Suffix: RES - / bore only Ordering Suffix: RE - / - 8 bore Pressure Rating: / - bore: thru 50 PSI bore: thru 00 PSI 5-8 bore: thru 00 PSI (pneumatic only) Material: Steel black oxide with sintered bronze bearing RW THIRD NGLE Ordering Suffix: RW Bore: / - 5 : Husky only Temperature: 00ºF Max. Material: / bore: Buna O-ring -/8-5 bore: Urethane wiper ll dimensions are in inches unless otherwise noted.
Non-Rotating Option 0º The non-rotating option requires air line lubrication to prevent bearing and rod wear. Female threads not shown for clarity Lobe orientation on the rod is random Double rod end model has polygon on front end only +/- º radial movement should be expected, do not torque the bearing pplications Example YES NO Basic Orientation Workholding Fixtures Marking Presses Parts Ejectors Elevators Robotic End Effectors Custom Escapements Clamping Long Strokes Pivoting pplications Side Loads Torque Loads Off Center Loads NOTE: For load bearing applications see our Guided Cylinder product line Fine Thread Rod Tap Standard Course Thread Optional Fine Thread ("FT") ll dimensions are in inches unless otherwise noted. X X X X X Nominal Dia. #0-5/6-8 /8-6 /- #0-5/6- /8- /-0 NOTE: FT is standard on 5 full husky through 8 bore. B / - 8 Bore Options Nominal Sizes (inches) C B C D 5/6..07.9. /..7.5 5/8.6.5.59.67 /.75.9.70.80.00.0.9.08 These dimensions are for drafting purposes only D NR Basic Workholding Fixtures Double rod end will decrease deflection by 5% Ordering Suffix: NR : Husky recommended Stroke: Under recommended Service: Pneumatic only Material: 0 stainless steel rod, brass, or bronze bearing Ordering suffix should immediately follow stroke length. Ex: SFHD8XNR-RF The unique three sided polygon rod often eliminates the need for external alignment devices. Custom Escapements Double acting, independently controlled pneumatic escapements Square body design allows close center line positioning www.compactautomation.com (86) 67-95 FT Ordering Suffix: FT ll Styles THIRD NGLE Modifications Welcome Special stroke lengths, port orientation, mounting configuration. 78
79 Style S End Mount / - Bore Options Short Rear Clevis with Eye Mount NOTE: Mount can be rotated 90º.5 D SQ B DI E F Short Rear Clevis NOTE: Mount can be rotated 90º SQ B DI N O C DI THRU MOUNTING HOLE S WIDE X T DP L Q R G H J H J M 0º MX P DI PIN ~ ~ SRCE Ordering Suffix: SRCE Bore: / - Style: S only Rod: Single only Service: Pneumatic only Rating: / - bore: thru 50 PSI -/ - bore: thru 00 PSI Pivot: 0º Material: Short Rear Clevis: DUE TO VRITIONS IN See Below ORIENTTION, CONSULT FCTORY Eye Mount: / bore: luminum black anodized with sintered bronze bearing Short Rear Clevis -/8 - -/ bore: luminum black anodized with Eye Mount steel bearing bore: Steel black oxide with steel bearing DUE TO VRITIONS IN ORIENTTION, CONSULT FCTORY SRC Ordering Suffix: SRC Bore: / - Style: S only Rod: Single only Material: luminum black anodized with sintered bronze bearings and case hardened pin and clips Bore B C D E F G H J L M N O P Q R S T /.5.69.8.9.88.5.9.8.69.9.00.75.9.8.75.8.56 -/8.88.8.9..9.00.75..9.9.88.5.8.75..69 -/8.75.5.8.5.00..9.8.6.9.00.6..00..88-5/8.00.5.8.5.00..9.8.6.9.00.6..00..88.5..5.00.88.8.00.88..00.6..6.5..9 -/.00.00...8.00.00.56..88..00.6.8.6.5.5..00...8.00.5.56....5.88.8.75.5. THIRD NGLE www.compactautomation.com (86) 67-95 ll dimensions are in inches unless otherwise noted.
Flange Mount (Shown as Rear Flange) / - -5/8 Bore F C S J DI THRU - Bore F C J DI MOUNTING HOLES ( PLCES) B B D H K DI THRU CLERNCE FOR CYLINDER ROD D G E H K DI THRU CLERNCE FOR CYLINDER ROD ~ / - Bore Options L L ~ DUE TO VRITIONS IN ORIENTTION, CONSULT FCTORY DUE TO VRITIONS IN ORIENTTION, CONSULT FCTORY Bore B C D E F G H J K L /.5..75.5.6.5..5 -/8.5.00.5.75..75.5 -/8.75.8.5.5.88.75..88.5-5/8.00.5.00.00...5.75.00.5.5.5.00.8.8.8 -/..06...8.00..6.8.6..00...75.88...8 Front Flange FF or Rear Flange RF Ordering Suffix: FF or RF Bore: / - Style: S only Rotation: 90º Material: luminum black anodized FF/RF can be rotated 90º ll dimensions are in inches unless otherwise noted. Style S End Mount THIRD NGLE www.compactautomation.com (86) 67-95 80
8 Style B Side Mount End Bracket C F / - Bore Options B Side Bracket B E + STROKE Number of brackets required: Two mounting holes = bracket Four mounting holes = brackets C TYP Number of brackets required: Two mounting holes = bracket Four mounting holes = brackets D D DI THRU MOUNTING HOLE ( PLCES, PER END) E DI THRU G H H J J K G / F / G SQ F SQ EB Ordering Suffix: EB Bore: / - Style: B only Material: luminum black anodized Bore B C D E F G H J K /..8.9..9.5.9.88.5 -/8..8.9..9.9. -/8.5.8 SEE.5.75.5.5.75-5/8.5.8 NOTE.5.00.5.00.. BELOW.5.5.00 -/...5.00.5.00.00.6.8....88 NOTE: Please consult factory. Body lengths differ depending on duty type, magnetic option, etc.; therefore, this dimension will vary with each cylinder. SB THIRD NGLE Ordering Suffix: SB Bore: / - Style: B only Material: luminum black anodized Bore B C D E F G H J /.75.8.9..5.9.88.5 -/8.75.8.9..5.00 -/8.00.5.8.75.5.5.75-5/8.00.5.8.00.5.00.00...5.00 -/.00...00.5.00.5.6.8....75 www.compactautomation.com (86) 67-95 ll dimensions are in inches unless otherwise noted.
Flange Mount (Shown as Rear Flange) / - -/8 Bore J DI THRU K DI THRU CLERNCE FOR CYLINDER ROD -/8 - Bore J DI THRU ( PLCES) K DI THRU CLERNCE FOR CYLINDER ROD J DI THRU ( PLCES) F F G. DI THRU CLERNCE FOR CYLINDER ROD C C C B B B Eº D D H G D F H E H L L ~ ~ L K ~ / - 8 Bore Options DUE TO VRITIONS IN ORIENTTION, CONSULT FCTORY DUE TO VRITIONS IN ORIENTTION, CONSULT FCTORY Bore B C D E F G H J K L /.5.00.5.75..5 -/8.00.5.00.00..75.5 -/8.8.9.9...00.56.00..88.5-5/8.5.00.5.5.5.00...5.00.5.5.00.8.8.8 -/.75.88...75.88.8.6.8.00.00.8...00.8.00...8 5.00.5.8.8.5 5.00.. 5-8 Bore DUE TO VRITIONS IN ORIEINTTION, CONSULT FCTORY Bore B C D E F G H J K L 5 7.00 6.00 0.00 5.00..8 6.00 6 7.00 6.00 8.00 5.00..8 6.00 8 9.75 8.00.75 5.75.00 6.5 8.00 Front Flange FF or Rear Flange RF Ordering Suffix: FF or RF Style: R only Material: / - 5 bore: luminum black anodized 6 & 8 bore: Steel black oxide / - 6 Flange can be rotated 90º 8 Flange can be rotated 60º ll dimensions are in inches unless otherwise noted. Style R End Mount THIRD NGLE www.compactautomation.com (86) 67-95 8
8 Style R End Mount Pivot Shaft / - Bore B C DI / - 8 Bore Options B D DI Bore B C D E F /.5..8.75. -/8.6..88.8.9. -/8.88...8.06. -5/8...8.8.9..5.59.00.9 -/.75.59.75.9 5.5.59.00.6.00.5 6.5.59 5.00.6.5 5-8 Bore.00.75 Bore B C 5 8.00 6.00.00 6 9.00 7.00 8.00 9.00 E.00 B DI F.00 DI.5 C.06 ~.06.06. ~ DUE TO VRITIONS IN ORIENTTION, CONSULT FCTORY DUE TO VRITIONS IN ORIENTTION, CONSULT FCTORY PS THIRD NGLE Ordering Suffix: PS Rod: Single only Style: R only Material: Steel black oxide shaft. 5-8 bore with aluminum mounting bracket. www.compactautomation.com (86) 67-95 ll dimensions are in inches unless otherwise noted.
Short Pivot Mount / - Bore D E B F G DI C DI* THRU MOUNTING HOLE K L J DI N M H / - 8 Bore Options ~ Pº LC MX PIVOT DUE TO VRITIONS IN ORIENTTION, CONSULT FCTORY * bore = mounting holes. Consult factory for mounting hole locations. BRCKET Bore B C D E F G H J K L M N P /.88.9..5.8.8.75.8.8.75.8. 75 -/8.5.9..5.8.8.88.75.8.8.56.8. 60 -/8.9..5.8.8..75.8.8.69.8. 55-5/8.75.9..5.8.8.8.75.8.8.8.8. 50.6...00.9.6.00.5.00.6.9 60 -/....00.9.6.5.5.6.9 50.6...6.6.00.6.75.5.75.5 5 5.75.8...75 5.00.6..8.88.5 5 5-8 Bore.00.88.6 B DI Bore B C D 5 7.5 6.00.5 55 6 8.5 7.00.75 5 8 0.5 9.00.75 5.5 DI THRU MOUNTING HOLE ( PLCES).00 DI.75 C. ~ C L Dº DUE TO VRITIONS IN ORIENTTION, CONSULT FCTORY SP Ordering Suffix: SP Rod: Single only Style: R only Pivot: See table below Material: Steel black oxide pivot shaft, aluminum black anodized bracket with sintered bronze bearings PIVOT SHFT MOUNTING SURFCE PIVOT RNGE ll dimensions are in inches unless otherwise noted. Style R End Mount THIRD NGLE www.compactautomation.com (86) 67-95 8
85 Style R End Mount D E DI THRU MOUNTING HOLE ( PLCES) / - Bore Options Long Pivot Mount B F DI C H G M L DI N P J K O Q ~ LP Ordering Suffix: LP Bore: / - Rod: Single only Style: R only Pivot: 80º Material: Steel black oxide pivot shaft with aluminum black anodized brackets and sintered bronze bearings DUE TO VRITIONS IN ORIENTTION, CONSULT FCTORY BRCKET PIVOT SHFT Bore B C D E F G H J K L M N O P Q /.75.5..5..8.00..8.06.5.00 -/8..6..5..88.8.00..8.06.5.00 -/8.8.88..5...8.00..8.00.5.5.00-5/8.8...8.8.8..8.6.5.00 5.00.5.59.8.8.00.9.6.5.00 -/ 5.5.75.59.8..8.9.75.00..75.8 5.75 5.5.59.8..00.8.5.75.6.00..75.8 7.5 6.5.59. 5.00.6.75.5.00.6.6.00.00 THIRD NGLE www.compactautomation.com (86) 67-95 ll dimensions are in inches unless otherwise noted.
Nose Mount DI B ROD DI D ROD EXTENSION (SEE CHRT BELOW) B CROSS POINTS (REF) C E THRED F +.000 -.00 PILOT DI CROSS FLTS (REF) / - 5 Bore Options.5. NM Ordering Suffix: NM Bore: / - 5 : Standard only Style: R only Material: / bore: Brass -/8-5 bore: luminum black anodized with DUE TO VRITIONS IN sintered bronze ORIENTTION, CONSULT FCTORY bearing Bore B C D E F /..00 /-6 x 5/8.750 -/8.88.00 - x 5/8.999 -/8..6.00 -/- x 5/8.9-5/8.8.6.00 See Rod -/- x 5/8.9 Extension.00.6.00 -/- x 5/8.9 Chart -/.75 Below -/- x -/8.99.00.75 -/- x -/8.99 5.00.75 - x -/8.999 5 6.00.75 - x -/8.999 Optional Jam Nut (order separately) C (CLSS B THREDS) D Part No. B C D NT..7 /-6.9 NT.69 -.9 NT.88. -/-.5 NT.5.5 -/-.5 NT.00.9 -.5 ll dimensions are in inches unless otherwise noted. Style R End Mount THIRD NGLE "D" - Rod Extension Chart Stroke Bore Piston Type /8 / /8 / 5/8 / 7/8 -/8 -/ -/8 -/ -5/8 -/ -7/8 & up Non-magnetic STD STD+.5 STD STD+.5 /" thru " STD STD+.5 Magnetic STD STD+.5 STD STD+.5 STD STD+. STD STD+. STD+. STD STD STD STD -/" thru 5" Non-magnetic STD+.5 STD STD+.5 STD STD+.5 STD+. Magnetic STD+.5 STD STD+.5 STD STD+.5 STD Chart STD =.06 on / bore =. on -/8 bore and longer www.compactautomation.com (86) 67-95 86
Sensors Standard Limit Sensors Low Cost and Compact size Dual LED indicators for power and signal Circuit protection for surge and polarity High-flex robotic grade cable with,8mm (/6 ) bend radius. 05 strand primaries. CE compliant / IP67 and NEM 6P rated 00% solid state device for maximum life cord options (Shown with Quick Disconnect Option) Prong Plug #WSKLP, #WSCLP, #WSKLPS, #WSCLPS Optional Quick Disconnect Sensor Cable - Specify K or C Plug - Prong, 0,5 METERS WS_LPS 0,5 METERS WS_LP M8x (MLE CONNECTION) Socket Mating Cable For use with: #WSKLP, #WSCLP, #WSKLPS, #WSCLPS, Sold Separately LED INDICTOR Sinking Sourcing R R5 Part No. WSKL *Mating socket receptacle available, part # R denotes meter cable WS_LP BLUE BLCK BROWN Sensor Type (Wiring diagrams and definitions on page 88) (-) (0) (+) WS_LPS with threaded, sealed connectors Receptacle - Socket (-) BLUE (0) BLCK (+) BROWN Quick Disconnect WSKLP * NPN WSKL- WSKLPS * WSCL WSCLP * PNP WSCL- WSCLPS * Cord Types * METERS, Meter Meter M8x NUT 9,5 *R - Meters *R5-5 Meters *R7-7 Meters R7 FEMLE CONNECTION 87 www.compactautomation.com (86) 67-95
Comtronic Sensors Dimensional Information Must specify K (sinking) or C (sourcing) when ordering - Specify K or C,0 WS_L DUL LED INDICTORS LOCKING SCREW,, DI Wiring Diagrams and Definitions For units with flying leads NPN Output Sinking (K) WS_L- denotes meter cable OR METERS ( OR 0 FEET) (+) Brown +5 to + VDC (0) Black (-) Blue (+) BROWN (-) BLUE (0) BLCK Part No. WSKL- - Sinking output with meter cable. SENSING FCE 6,0 Load Parameters Operating Voltage PNP Output Sourcing (C) (+) Brown +5 to + VDC Sensors Specifications Comtronic Standard Limit Sensors NPN (sinking) WSKL, WSKL-, WSKLP, WSKLPS Ideal for complex controls utilizing multiple power supplies. Ideal for single power supply applications. sinking output sensor complete a circuit by connecting sourcing output sensor completes a circuit by connecting the load to ground. Sinking output sensors in a sequence the load to the supply current. ll sourcing output sensors must can have different supply voltages. The ground is their have the same supply voltage. common factor. www.compactautomation.com (86) 67-95 (0) Black (-) Blue 5- VDC Load PNP (sourcing) WSCL, WSCL-, WSCLP, WSCLPS Current Consumption On Off 6m (at V) 7m (at V) m (at V) 7m (at V) Switching Current 00m Max Voltage Drop.5 V Max @ 00m Operating Frequency KHz Max Switch Logic Sinking, Normally Open Sourcing, Normally Open LED Function Green Red Operating Temperature Circuit Protection Power On Switch ctive (Magnet Present) 0ºC to 70º C Reverse Polarity / Surge bsorber Environmental Certifications IEC standard IP67, NEM 6P Wire Type High flex, WG / 05 strand primary Housing Material Zinc diecast Housing Color Code Black Silver Shock Resistance 0G Max Vibration Strength 9G Max 88
Rod End lignment Coupler Inch Sizes J (OFF CENTER DJUSTMENT) K HEX (FOR SOCKET KEY) C FLT ll dimensions are in inches. B DI DI º MX H TP E F D G THRED THIRD NGLE Material: Hardened steel Finish: Black Oxide Finish Maximum Temperature Rating: 00ºF (9.ºC) NOTE: Do not use alignment couplers on pivoting applications. Sold separately - Not attached to the cylinder. pplicable Screw Compact ir Male Female G H Unit xial Load B C D E F Male Female Thread J K Weight Ratings Size Thread Thread Cylinders Thread x Depth (oz.) (lbs.) /" # 8 CCC8 Coarse 9/6 / 7/ 5/6 7/6 / # 8- #8- x / /6 5/6 0. 80 CCC0 Coarse # 0- #0- x 5/6 /" #0 CCF0 Coarse Fine # 0- #0- x 5/6 9/6 5/6 / / 9/6 / CFF0 Fine # 0- #0- x 5/6 /6 / 0.5 80 CFC0 Fine Coarse # 0- #0- x 5/6 /" CCC Coarse 5/6 / 7/6 / /6 9/6 /-0 /-0 x / CCF Coarse Fine /-0 /-8 x / / /8.6 50 CCC56 Coarse 5/6-8 5/6-8 x 5/8 -/8" 5/6" CCF56 Coarse Fine 5/6-8 5/6- x 5/8 5/6 / 7/6 /6 /6 9/6 CFF56 Fine 5/6-5/6- x 5/8 /6 5/.6 580 CFC56 Fine Coarse 5/6-5/6-8 x 5/8 CCC56L Coarse 5/6-8 5/6-8 x 5/8 -/8" 5/6" CCF56L Coarse Fine 5/6-8 5/6- x 5/8 -/8 5/8 9/6 9/6 -/ / CFF56L Fine 5/6-5/6- x 5/8 / 5/. 580 CFC56L Fine Coarse 5/6-5/6-8 x 5/8 CCC8 Coarse /8-6 /8-6 x 5/8 -/8" CCF8 Coarse Fine /8-6 /8- x 5/8-5/8" /8" -/8 5/8 9/6 9/ -/ / CFF8 Fine /8- /8- x 5/8.0" CFC8 Fine Coarse /8- /8-6 x 5/8 / /6. 80 -/".0".0" 5.0" 6.0" 8.0" 7/6" CCF76 Coarse Fine -9/6 / /6 / -/8 -/8 /- 7/6-0 x /6 /6 / 8.8 690 CFF76 Fine /-0 7/6-0 x /6 CCC Coarse /- /- x /6 CCF Coarse Fine /- /-0 x /6 /" -9/6 / /6 / -/8 -/8 /6 / 8.8 690 CFF Fine /-0 /-0 x /6 CFC Fine Coarse /-0 /- x /6 CCC58 Coarse 5/8-5/8- x.0 CCF58 Coarse Fine 5/8-5/8-8 x.0 5/8" -/.0 5/6 5/6 -/ -/ /6 5/6.0 0 CFF58 Fine 5/8-8 5/8-8 x.0 CFC58 Fine Coarse 5/8-8 5/8- x.0 89 www.compactautomation.com (86) 67-95
º MX H TP Rod End lignment Coupler Combination Sizes E F D G THRED ll dimensions are in millimeters except where noted. pplicable Compact ir Cylinder J (OFF CENTER DJUSTMENT) B DI K HEX (FOR SOCKET KEY) B C D E F C FLT G Male Thread HOUSING HOLDS MLE THRED CPTIVE ND LIMITS RDIL PLY SHFT FREE FLOTING SHFT DJUSTS FOR XIL MISLIGNMENT DI H Female Thread X Depth SNP RING www.compactautomation.com (86) 67-95 FIRST NGLE Material: Hardened steel Finish: Black Oxide Finish Maximum Temperature Rating: 00ºF (9.ºC) NOTE: Do not use alignment couplers on pivoting applications. Sold separately - Not attached to the cylinder. J K mm (Inch) /" & 0mm WCC8-M, 6, 5,0 8,0, 8,7 #8- Mx0,7 x 6,98 (5/6) 0, 0mm WCM-C8,0 6,5 5,6 6,0,5 0,0 Mx0,7 #8- x /,5 (.098) WCC0-M5 #0- /", 7,6 7,0 8,7,5 0, M5x0,8 x 8,8 (/) WCF0-M5 #0-0, 0mm WCM5-C0 #0- x 5/6,0 7,9 6,5 8,0 5,,0 M5x0,8,0 (.8) 5mm WCM5-F0 #0- x 5/6 - WCC-M6,8, 0,0 0, 0,8, /-0 M6x x,8 (/8) WCM6-C /-0 x / 0,8 0mm,0,7, 9,7,5 5,0 M6x,0 (.57) WCM6-F /-8 x / WCC56-M8 5/6-8 -/8",8, 0,0 7,5 0,8, M8x,5 x,97 (5/) WCF56-M8 5/6-0, WCM8-C56 5/6-8 x 5/8 -,0,7,,7,5 6,0 M8x,5 5,0 (.97) WCM8-F56 5/6- x 5/8 -/8 /8-6 WCC8-M0-5/8 8,6 5,6,0 5, 6, 9, M0x,5 x 5,76 (/6).0" /8- WCF8-M0 0,8 WCM0-C8 /8-6 x 5/8-8,0 5,9, 6 6,5 0,0 M0x,5 7,0 (.76) WCM0-F8 /8- x 5/8 WCM-F76 9,0 9, 7,5 7,9 6,5 0,0 Mx,75 7/6-0 x /6 8,0 (.5) -/ WCC-M /-.0 9,7 8,8 6,0 9, 5, 8,6 Mx,75 x 9 6,5 (/),6.0 WCF-M /-0 5.0" WCM-C /- x /6 9,0 9, 7,5 7,9 6,5 0,0 Mx,75 8,0 (.5) WCM-F /-0 x /6 Unit Weight (Grams) xial Load Rating (N), 85, 85 5, 05 5, 580 90,7 700 50,0 750 URETHNE WSHER REDUCES LINER BCKLSH HRDENED WSHER PROVIDES WER RESISTNCE 90
Flow Controls Unique Inch to Metric Combinations Inch Sizes: #0-, /8NPTF, /NPTF Metric Sizes: M5, G/8, G/ #0- valves available with a space saving integral barb for /8 I.D. tubing. Flow Paths Style MO Meter Out Metered Output Free Flow Input unique needle design minimizes turbulence and improves flow control ability. super fine pitch needle thread provides the finest adjustment available. Captive needle cannot be adjusted out of the housing. Style MI Meter In Precision Control Sizes Needle Model Numbers* Port Thread # 0- M5 /8-7NPTF G/8 /-8NPTF G/ Factory Installed Compact utomation Products will factory install any MO model flow control at no charge. How to Order:.) Verify MO model number required from the chart above..) Choose factory installation: PC Head end only, PC Cap end only, PC Head and cap end.) Remove MO from model number and add PC option to the end Meter Out style valves can be factory installed to your Compact utomation cylinders, guided cylinders, gripper, etc... at no extra charge. See Factory Installed below. Metered Input Free Flow Output Pitch # 0-80 TPI M5 x.8 /8NPTF.mm 60 TPI G/8.mm /NPTF 56 TPI G/.5mm PC HED END PC BOTH ENDS Number of Turns "MO" Color Code: Black "MI" Color Code: Red "NV" Color Code: Silver Model # Male Thread Female Thread Model # Male Thread Female Thread Factory Installed part number example: G8-8PC Flow control required: MOG8-8 Install at: head and cap end PC (Remove MO add PC to end) 6 8 8 Model # Male Thread PC CP END Style NV Needle Valve Meter Both Ways Female Thread MO0 # 0- # 0- MI0 # 0- # 0- NV0 # 0- # 0- MO5 M5 M5 MI5 M5 M5 NV5 M5 M5 MO0-5 # 0- M5 MI0-5 # 0- M5 NV0-5 # 0- M5 MO0B M5 # 0- MI5-0 M5 # 0- NV5-0 M5 # 0- MO0B # 0- /8" barb MI0B # 0- /8" barb NV0B # 0- /8" barb MO5B M5 /8" barb MI5B M5 /8" barb NV5B M5 /8" barb MO8 /8NPTF /8NPTF MI8 /8NPTF /8NPTF NV8 /8NPTF /8NPTF MOG8 G/8 G/8 MIG8 G/8 G/8 NVG8 G/8 G/8 MO8-G8 /8NPTF G/8 MI8-G8 /8NPTF G/8 NV8-G8 /8NPTF G/8 MOG8-8 G/8 /8NPTF MIG8-8 G/8 /8NPTF NVG8-8 G/8 /8NPTF MO /NPTF /NPTF MI /NPTF /NPTF NV /NPTF /NPTF MOG G/ G/ MIG G/ G/ NVG G/ G/ MO-G /NPTF G/ MI-G /NPTF G/ NV-G /NPTF G/ MOG- G/ /NPTF MIG- G/ /NPTF NVG- G/ /NPTF Metered Input Metered Output NPTF = National Pipe Thread Dry Seal (/8NPTF and / NPTF) G = BSPP British Standard Pipe Parallel (G/8 and G/) /8 Barb is for /8 ID polyurethane or vinyl tubing * = ll model numbers are available with the Knob Option, add suffix K to the end of the part number. Specify our unique Inch to Metric or Metric to Inch combination flow controls factory installed to convert cylinder ports. For example, metric cylinder part number WS5x5 - G8-8PC would place two metered output flow controls on the cylinder and allow for the use of /8-7 NPTF fittings. 9 www.compactautomation.com (86) 67-95
Flow Controls Dimension Information Minimum body length for two port controls - 7/8 Inch Version G HEX F THRED Combination B C SQ Model # B C D E F G MO0 MI0 NV0 MO8 MI8 NV8 MO MI NV 5/8 9/ /8 7/ /8 E D # 0-5/6.0.9 9/6.0.8 /8-7 9/6 NPTF -/8. /6. /-8 NPTF /6 Important Note The combination units with Inch and Metric threads are modular versions of both drawings. Flow Chart ir Flow* CFM l/min 7 98 6 5 0 70 88 57 8 0 Materials and Technical Data Size M5 # 0- /8 and / / /8 5 & 0 0 0.5.5.5.5.5 5 5.5 6 6.5 7 7.5 8 8.5 Needle Rotations * t 60 PSI (. BR) and 60ºF (5ºC) Housing Nickel Plated Brass nodized luminum Inner Housing Nickel Plated Brass Needle Stainless Steel Seals Buna-N 0 F to 00 F -5 C to 90 C Barb Fitting for #0- or M5 only #0- or M5 Male to Barb for /8 I.D. tubing 5/6 HEX NYLON GSKET #0- THRED Model Number Examples /6 9/ Knob Option vailable with any valve Inch Version /8 SQ 7/ /8 MO0B MI0B NV0B MO5B MI5B NV5B Model Number MO0K MI0K NV0K MO8K MI8K NV8K MOK MIK NVK 5/ 5/6 9/6 B (max.) 9/ -5/6-5/8 Cv Factor Cv = Volume of water in gallons at 60ºF (5ºC) that will flow per minute through the valve with a pressure differential of PSI across the valve. Style Pressure Ratings 0 to 75 PSI 0 to BR Flow # 0- Direction M5 (Fully open) Captive Needle Yes /8-7 G/8 60 Swivel Gasket Material Yes- Prior to tightening Nylon /8NPTF and /NPTF 0 F to 00 F swivel after -5 C to 90 C mounting B /-8 G/ MO Free Cv.08.5. Metered Cv.05.0.8 MI Free Cv.07..0 Metered Cv.06..9 NV Metered Cv.05..8 www.compactautomation.com (86) 67-95 9
/ - 8 Bore Reverse ssembly Simple solution to a mounting or porting interference. Compact cylinders are symmetrical and easily assembled in reverse. When specifying R the mounting and porting orientations will change; see examples below. This option is not applicable to Magnetic Piston cylinders. Reverse ssembly Ordering Suffix R Example / Bore Short Stroke Front View Standard ssembly Example / Bore Long Stroke Front View Standard ssembly Rear View Rear View Front View Front View Reminder: This option is not applicable to Magnetic Piston cylinders. Reverse ssembly Reverse ssembly Rear View Orientation of porting and mounting change Rear View Orientation of porting and mounting change 9 www.compactautomation.com (86) 67-95
Usable Female Rod Thread On magnetic piston style cylinders, refer to / longer stroke when determining tap depth. Bore Rod Tap Rod Diameter Standard Optional Suffix: FT /.5 #8- /. #0- #0- -/8 5/6-8 5/6- -/8.6 /8-6 /8- -5/8.6 /8-6 /8-.6 /8-6 /8- -/.75 /- /-0.75 /- /-0 Rod Tap Information TP SIZE ROD DI TP DEPTH Tap Depths (Stroke) /8 / /8 / 5/8 / 7/8 " and longer Standard.5.5.8..... Intermediate.5.8...... Heavy.5.8...... Standard.5.8.8..... Intermediate.8....... Heavy........ Standard..8..6.69.8.8 Intermediate..6.69.8.8.8.8 Heavy.6.69.8.8.8.8.8.8 Standard...69.8.88.9 Intermediate.69.8.88.9.9.9 Heavy.69.8.88.9.9.9.9.9 Standard...69.8.88.9 Intermediate.69.8.88.9.9.9 Heavy.69.8.88.9.9.9.9.9 Standard.69.69.8.88.9.9 Intermediate.69.69.8.88.9.9.9.9 Heavy.8.88.9.9.9.9.9.9 Standard.6.6.75.88.00.00.5 Intermediate.6.75.88.00.00.5.5.5 Heavy.88.00.00.5.5.5.5.5 Standard.6.6.75.88.00.00.5 Intermediate.6.75.88.00.00.5.5.5 Heavy.88.00.00.5.5.5.5.5 Standard.6.75.75.88.88.88.00.5.75 /- /-0 Intermediate.75.88.88.88.00.5.5.5 Heavy.88.88.00.5.5.5.5.5 Standard.6.75.75.88.88.88.00.5.75 /- /-0 5 Intermediate.75.88.88.88.00.5.5.5.00 5/8-8 Heavy.88.9.00.5.5.5.5.5 6.00 5/8-8 Standard.75.8.88.9.00.00.5.5 8.00 5/8-8 Standard.75.8.88.9.00.00.5.5 Usable Wrench Flats Bore B Flat C Dia /.06..5 /.06.5. -/8.. -/8, -5/8, "..56.6 -/,,, 5"..69.75 5FH, 6, 8"..9.00 B C / - 8 Bore For low cost male thread see the ccessories section, Male Stud on page 76. www.compactautomation.com (86) 67-95 9
/ - 8 Bore 95 Cylinder Weight Ounces to Grams (Ounces x 8.9 = Grams) pproximate Unit Weights (Ounces) Example: Sx Magnetic Piston.55 S Square / bore.0 x Rectangular and Square body styles # of /8 increments.6 (.x8) 6.5 ounces Non-Magnetic Piston Magnetic Piston dder Standard Intermediate Heavy Standard Intermediate Heavy Rod End Single Double Single Single Double Single Double Single Single Double / Zero stroke.90.95.0.0.0 per /8" stroke.5.0.5.5.0.5.0.0.0 / Zero stroke.00.0.00.80.00 per /8" stroke.0.0.0.0.0.55.60.70.85.90 Zero stroke.0.0.0 5.70 6.0 -/8 per /8" stroke.0.0.0.75.80.0.55.60 Zero stroke 5 6.0 7.0 9 0.0 -/8 per /8" stroke.60.60.95.00.65.0.5 Zero stroke 6.80 7.0 9.0.0.0-5/8 per /8" stroke.60.70.60.60.70.0.0.0.65.00 Zero stroke.80.0 5.0 8.0 9.00 per /8" stroke.90.00.00.90.00.95.65.85.05 Zero stroke 8.0 9.0.0 7.60 9.00 -/ per /8" stroke.0.0.0.0.5.55 6.5 6.80 Zero stroke 0.0.0 6.70.0.60 per /8" stroke.80.0.80.80.0.0.5 6.0 8.80 9.00 Round body styles Non-Magnetic Piston Magnetic Piston dder Standard Intermediate Heavy Standard Intermediate Heavy Rod End Single Double Single Single Double Single Double Single Single Double / Zero stroke....5.5.6.7.8 per /8 stroke.......... / Zero stroke.0.0.0.00.0 per /8 stroke.0.0.0.0.0..6.5.. Zero stroke.70.00 5.0 6.0 6.80 -/8 per /8 stroke.60.60.8.0.78.. Zero stroke 6.0 6.90 8.0 0.0 0.90 -/8 per /8 stroke.60.70.60.60.70.59.6.6.7.96 Zero stroke 7.80 8.0 0.00.00.80-5/8 per /8 stroke.70.80.70.70.80.89.90.79.6.70 Zero stroke.0.0 6.60 9.70 0.0 per /8 stroke.00.0.00.00.0.80.5.7.9.5 Zero stroke 9.60 0.60.0 8.80 0.0 -/ per /8 stroke.0.0.0.0.0.7..9 6.0 6.75 Zero stroke 0.0 6.80.0.70 per /8 stroke.0.60.0.0.60.7. 6. 8.9 9.5 Zero stroke 5 5.00 60.60 68.90 7.0 per /8 stroke.60.90.60.60.90 5.07 5.0 9.89.86.65 Zero stroke 79.0 80.90 88.0 05.70 09.0 5 per /8 stroke.90.0.90.90.0 8.09 8.9 5.89.0.9 6 Zero stroke.0 7 per /8 stroke.0.90.00.7 8 Zero stroke 9.0.00 per /8 stroke.0 9.8 8.7 www.compactautomation.com (86) 67-95
pproximate Unit Weights (Ounces) ccessories ccessory Weight Bore Suffix Description / / -/8 -/8-5/8 -/ 5 6 8 DJ djustable Retract Stroke.7.6.5.97. 5.09 5.96 0.0 CF CF CF CF CBSS Clevis Bracket.6.79.7.7.7.7.8.8.8.8 9.8 9.8 EB End Bracket (flange).9.6..9..0.5.66 FF Front Flange ("S") style only).8.8..78.7.85 5. 9.0 FF Front Flange ("R") style only).8.8.0.77.89.7 5.59 9.0 6.6 6.90 57.0 57.0 LP Long Pivot Mount.6.79.6 5.58 7..7..57 MS Male Stud.0.06.....96.96...90.90 NM Nose Mount.5..09.05.78 5.67 9.76..00.8 PS Pivot Shaft.9.0...8 6. 7.70 7.00. 9.75 6.5 RE Rod Eye..5.5.0.0.0.8.8.8.8.80.80 RF Rear Flange ("S") style only).8.8..78.7.85 5. 9.0 / - 8 Bore RF Rear Flange ("R") style only).8.8.0.77.89.7 5.59 9.0 6.6 6.90 57.00 57.00 SB Side Bracket (flange).9..9.99.6.89.5.9 SP Short Pivot Mount.96..5. 7.59 0.7.7 7.70 55.8 6. 69.0 SRC Short Rear Clevis.8.86.5.97.5 5.5 0.9.88 SRCE Short Rear Clevis with Eye Mount.7.9.6.75 7.8.69 9.6 CF = Consult Factory www.compactautomation.com (86) 67-95 96
/ - 8 Bore Disassembly Maintenance / Bore (Snap Cap). Place cylinder under small arbor press, rear end cap up. pply 5 pounds of force.. Push the end cap down into the cylinder frame, retainer seal will remain in groove.. With an o-ring tool remove the retainer seal.. Push the piston rod assembly up to remove the rear face end cap. 5. Do not remove the piston rod assembly. 6. Turn cylinder over. 7. Repeat steps -, push rod end cap out with piston rod assembly and remove both. / - 8 Bore. Place cylinder in vise, rear end cap up. Place spanner wrench pins in notches of the end cap. Turn clockwise. The retaining wire will back out of the cylinder.. Stop turning when wire becomes loose. 5. Push the end cap down into the frame. 6. Remove the wire by pulling the hooked end from the cylinder bore. 7. Push the piston rod assembly up to remove the end cap. 8. Do not remove piston rod assembly. 9. Turn cylinder over. 0. Repeat steps -6, push front end cap out with piston rod assembly and remove both. General Repair Instructions. Remove any seal that becomes visible during repair with an o-ring tool.. Clean all grooves with a soft cloth.. Lightly lubricate seal grooves, reset seals and lubricate again.. Repeat above steps, in reverse, to reassemble. 5. Bubble test cylinder to assure air tight seal. Instructions - / through 8. Using snap ring pliers, remove first snap ring.. Remove piston from rod and remove snap ring from opposite side.. Remove inner piston seal with an o-ring tool and reset seals as detailed above.. Reset snap ring with flat side facing out from center. 5. Place piston over seal. 6. Reset opposite snap ring with flat side facing out from center. 7. Reassemble and bubble test. RETINER SEL PISTON ROD SSEMBLY RBOR PRESS RER FCE END CP RETINING WIRE FRONT END CP PISTON ROD SSEMBLY RER END CP 97 www.compactautomation.com (86) 67-95
Repair Kits Repair Kits apply to Non-Magnetic and Magnetic piston cylinders, any duty. ll Repair Kits Include: Endcap Seals Shaft Seals Piston Seals Retaining Wire* Lubrication ( to milliliters) Snap Rings - RKD kits only Magnets Repair Kits Pneumatic Seals Hydraulic Seals ssembly Bore Rod End Standard Viton Teflon Hydraulic Viton Hyd Wrench / / -/8 -/8-5/8 -/ 5 FH5 6 8 Single RK RKV Double RKD RKDV Single RK RKV RKT RKH RKVH Double RKD RKDV RKDT RKDH RKDVH Single RK8 RKV8 RKT8 RKH8 RKVH8 Double RKD8 RKDV8 RKDT8 RKDH8 RKDVH8 Single RK8 RKV8 RKT8 RKH8 RKVH8 Double RKD8 RKDV8 RKDT8 RKDH8 RKDVH8 Single RK58 RKV58 RKT58 RKH58 RKVH58 Double RKD58 RKDV58 RKDT58 RKDH58 RKDVH58 Single RK RKV RKT RKH RKVH Double RKD RKDV RKDT RKDH RKDVH Single RK RKV RKT RKH RKVH Double RKD RKDV RKDT RKDH RKDVH Single RK RKV RKT RKH RKVH Double RKD RKDV RKDT RKDH RKDVH Single RK RKV RKT RKH RKVH Double RKD RKDV RKDT RKDH RKDVH Single RK5 RKV5 Double RKD5 RKDV5 Single RKFH5 RKFHV5 Double RKFHD5 RKFHDV5 Single RK6 RKV6 Double RKD6 RKDV6 Single RK8 RKV8 Double RKD8 RKDV8 Tools */ through -5/8 Bore Repair Kits only Bore and larger -- must be ordered separately. www.compactautomation.com (86) 67-95 W W W Repair Kits Flat Wrench FWS FWS FWS Part No. FWS Includes one each FWS, FWS, FWS Lubrication Lube One Lubricates approximately 0 medium size cylinders. / - 8 Bore 98
/ - 8 Bore pplication Ideas With only minor modification to Compact cylinder bodies and rod ends, these non-standard cylinder can be built and delivered quickly and cost effectively in any quantity. Back-to-Back or positions Equal stroke increments provide positions. Back-to-back assemblies feature a pilot locator between the cylinder to assure positive alignment. Cylinder must have support when used in a non-vertical application. -way valve circuit required for each cylinder. Multi-Position or more positions Three or more stroke increments can be achieved with in line multi-position cylinders. POSITION POSITION Unequal stroke increments provide or positions, depending on sequence of operation. POSITION POSITION Precise valve circuit design is critical. Front cylinder must include all previous cylinder increments. Example: Increments include + +. Front cylinder stroke, middle cylinder, back cylinder. Multi-Piston High Output Numerous pistons can be coupled to achieve extra output in limited space applications. Individual cylinders with a common rod, as shown in this diagram, can provide multiple output for push and pull. For design assistance and quotes contact your local distributor or our Technical Sales Department at (86) 67-95. 99 www.compactautomation.com (86) 67-95
Modifications to fit Customer Requirements Compact utomation Product s Technical Sales team understands the ever-changing industry. Each modified design is its own, requiring application - specific parts and know-how. We at Compact utomation Products pride ourselves in our ability to create or modify a cylinder to fit your application. Do you have an unusual space situation, material requirement, or other specific need you think is hopeless? If you think it can t be done, we think IT CN. Medical Device Twin Pinion/Common Rack 90º ctuator PCB Machine Tool Direct mounted control valve Food Processing Machine Multi-axis gripper with all Stainless Steel components Modified Products For your convenience, see the Request for Quote form, on pages 0 and 0. Semi Conductor Industry Heavily modified frame and oversized hollow rod Entertainment Industry nimation Cylinder Custom stainless steel body for hydraulic service / - 8 Bore www.compactautomation.com (86) 67-95 00