Analysis of the Tractor Age and its Effect on Fuel Consumption: Case Study of Sudan

Similar documents
Survey of Farm Power in the Mechanized Rainfed Agriculture in Gedarif State, Sudan

1. INTRODUCTION 3 2. COST COMPONENTS 17

MACHINERY COST ESTIMATES

PREDICTION OF FUEL CONSUMPTION

PREDICTION OF REPAIR & MAINTENANCE COSTS OF DIESEL ENGINE

MACHINERY COST ESTIMATES

Determination of power loss of combine harvester travel gear

Biofuel Potential for Transport Sector in Sudan

Modeling of Rolling Resistance for Bias-Ply Tire Based on Tire Dimensions, Inflation Pressure and Vertical Load

Comparative Field Evaluation of Three Models of a Tractor

Modeling of Contact Area for Radial-Ply Tire Based on Tire Size, Inflation Pressure and Vertical Load

Development and Evaluation of Tractors and Tillage Implements Instrumentation System

Nowaday s most of the agricultural operations are

Predicting Tractor Fuel Consumption

Effect of driving pattern parameters on fuel-economy for conventional and hybrid electric city buses

Modeling of Radial-Ply Tire Rolling Resistance Based on Tire Dimensions, Inflation Pressure and Vertical Load

Effect of driving patterns on fuel-economy for diesel and hybrid electric city buses

I. INTRODUCTION. Sehsah, E.M. Associate Prof., Agric. Eng. Dept Fac, of Agriculture, Kafr El Sheikh Univ.33516, Egypt

LESSON Transmission of Power Introduction

AIR QUALITY DETERIORATION IN TEHRAN DUE TO MOTORCYCLES

Performance of DC Motor Supplied From Single Phase AC-DC Rectifier

An Approach for Power Generation with Reduced Fuel Consumption using PTO Driven Generator

SUMMARY OF THE IMPACT ASSESSMENT

Smart Operation for AC Distribution Infrastructure Involving Hybrid Renewable Energy Sources

Grain Drying Simulation in a GT-380 Dryer using Energy Recovered from ICE Exhaust

Running Vehicle Emission Factors of Passenger Cars in Makassar, Indonesia

Machine Drive Electricity Use in the Industrial Sector

Machinery Cost Estimates: Field Operations

Chapter 5 ESTIMATION OF MAINTENANCE COST PER HOUR USING AGE REPLACEMENT COST MODEL

Electromagnetic Field Analysis for Permanent Magnet Retarder by Finite Element Method

Machinery Cost Estimates: Field Operations

A conceptual design of main components sizing for UMT PHEV powertrain

PREDICTION OF SPECIFIC FUEL CONSUMPTION IN TURBOCHARGED DIESEL ENGINES UNDER PARTIAL LOAD PERFORMANCE

Projections of global emissions of air pollutants

CHAPTER 4: MATCHING TRACTORS AND IMPLEMENTS - 41

Forage Harvester Evaluation

Flywheel energy storage retrofit system

Pump Control Ball Valve for Energy Savings

Prediction of Bias-Ply Tire Deflection Based on Contact Area Index, Inflation Pressure and Vertical Load Using Linear Regression Model

TESTING THE UNIFORMITY OF SPRAY DISTRIBUTION UNDER DIFFERENT APPLICATION PARAMETERS

Evaluation of Hydraulic Energy Nozzle Suitable for Low Velocity Air-Assisted Sprayer

e ISSN Visit us : DOI: /HAS/IJAE/8.1/85-91

TKP3501 Farm Mechanization

BATTERY OPERATED USG APPLICATOR ABSTRACT

A Cost Effective Method to Create Accurate Engine Performance Maps & Updating the Nebraska Pumping Plant Performance Criteria

Optimization of Seat Displacement and Settling Time of Quarter Car Model Vehicle Dynamic System Subjected to Speed Bump

DESIGN AND OPERATIONAL ASPECTS OF DIESEL GENERATORS POWER AND NUMBER FOR SEAGOING SHIPS

COST ANALYSIS FOR BRIDGE AND CULVERT. Essam A. Mostafa

The influence of fuel injection pump malfunctions of a marine 4-stroke Diesel engine on composition of exhaust gases

Modeling and Analysis of Vehicle with Wind-solar Photovoltaic Hybrid Generating System Zhi-jun Guo 1, a, Xiang-yu Kang 1, b

Analysis of Fuel Economy and Battery Life depending on the Types of HEV using Dynamic Programming

Electric vehicles a one-size-fits-all solution for emission reduction from transportation?

Interstate Freight in Australia,

EUROPEAN COMMITTEE UNDER THE GOVERNMENT OF THE REPUBLIC LITHUANIA. September 5, 2001 Final report summary

Facts and Figures. October 2006 List Release Special Edition BWC National Benefits and Related Facts October, 2006 (Previous Versions Obsolete)

Energy Saving and Emission Reduction Estimations of Electrified Railways in China

AN INVESTIGATION INTO HOW DIFFERENT BLENDS OF BIO-DIESEL AT A RANGE OF TEMPERATURES AFFECT ENGINE HORSEPOWER, TORQUE AND EMISSIONS

Original. M. Pang-Ngam 1, N. Soponpongpipat 1. Keywords: Optimum pipe diameter, Total cost, Engineering economic

MAINTENANCE COSTS OF INTENSIVELY USED SELF-PROPELLED MACHINES IN AGRICULTURAL COMPANIES

DESIGN OF THROTTLE BODY: A COMPARATIVE STUDY OF DIFFERENT SHAFT PROFILES USING CFD ANALYSIS

Analysis of Production and Sales Trend of Indian Automobile Industry

Analysis and calculation model of energy consumption and product yields of delayed coking units

INTERNATIONAL JOURNAL OF APPLIED ENGINEERING RESEARCH, DINDIGUL Volume 1, No 4, 2011

DISPLAYING OF TRACTOR PERFORMANCE

COSTS OF TRACTOR OWNERSHIP UNDER DIFFERENT MANAGEMENT SYSTEMS IN NIGERIA

Influence of Cylinder Bore Volume on Pressure Pulsations in a Hermetic Reciprocating Compressor

Implementation of telecontrol of solar home system based on Arduino via smartphone

Effect of Sample Size and Method of Sampling Pig Weights on the Accuracy of Estimating the Mean Weight of the Population 1

STIFFNESS CHARACTERISTICS OF MAIN BEARINGS FOUNDATION OF MARINE ENGINE

2. LITERATURE REVIEW. Keywords: Design hourly factor ( K-factor), annual average daily traffic(aadt), design hour volume(dhv), road design

Efficiency Measurement on Banking Sector in Bangladesh

Research in hydraulic brake components and operational factors influencing the hysteresis losses

THE alarming rate, at which global energy reserves are

FARM MACHINERY ECONOMIC COST ESTIMATES FOR LATE 2005

PRISM TM Refining and Marketing Industry Analysis

Automotive Industry Review Dennis DesRosiers March 8, 2011

Structure Parameters Optimization Analysis of Hydraulic Hammer System *

The Mechanics of Tractor - Implement Performance

KERN FIELD CROPS. Kern County 1031 S. Mt. Vernon Avenue Bakersfield, CA

Study of the Effect of CR on the Performance and Emissions of Diesel Engine Using Butanol-diesel Blends

Grid Services From Plug-In Hybrid Electric Vehicles: A Key To Economic Viability?

Research of Driving Performance for Heavy Duty Vehicle Running on Long Downhill Road Based on Engine Brake

Heat Transfer Enhancement for Double Pipe Heat Exchanger Using Twisted Wire Brush Inserts

BUILDING A ROBUST INDUSTRY INDEX BASED ON LONGITUDINAL DATA

New York Science Journal 2017;10(3)

Performance Evaluation of 4-WD Tractor at Various Gear rpm Combinations with Three Bottom M. B. Plough

A STUDY ON ENERGY MANAGEMENT SYSTEM FOR STABLE OPERATION OF ISOLATED MICROGRID

2003 fourth quarter and full-year results

Fuck Uber, 30 April, 2017

FUEL PROVISIONS FOR DREDGING PROJECTS

Introduction. Materials and Methods. How to Estimate Injection Percentage

Forage Harvester Evaluation

CONDITION EVALUATION OF ROTATING ELECTRICAL MACHINES IN PRACTICE

[Rao, 4(7): July, 2015] ISSN: (I2OR), Publication Impact Factor: 3.785

Objective The objective of the research was to analyze the amount of machine vibration and to approximate an optimum operational engine speed.

ADVANCES in NATURAL and APPLIED SCIENCES

INCREASING THE ELECTRIC MOTORS EFFICIENCY IN INDUSTRIAL APPLICATIONS

An Evaluation of the Relationship between the Seat Belt Usage Rates of Front Seat Occupants and Their Drivers

Monthly Economic Letter

SETUP AND OPERATIONAL COST ANALYSIS OF 1 HORSE POWER RATED SPLIT UNIT INVERTER AND NON INVERTER AIR CONDITIONER FOR HOME USAGE IN MALAYSIA

Transcription:

Analysis of the Tractor Age and its Effect on Fuel Consumption: Case Study of Sudan Farid Eltom. A. E1,2*, M. H. Dahab3,4, Ding Weiming 1, Mohamed Ali Kara 2 1 Department of Agricultural Mechanization, College of Engineering, Nanjing Agricultural University, Post Code 210031, Nanjing, Peoples Republic of China 2 After Sell Services Department, Danfodio commercial company 3 Faculty of Agriculture, University of Khartoum, Shamat13314, Sudan 4 Head of Blue Nile University, Blue Nile province, Sudan 79371 Abstract--Agricultural machinery maintenance has a crucial role for successful agricultural production. A field survey was carried out in Gezira Scheme, Blue Nile State and North Kordofan State, to collect data about tractor repair and maintenance costs, Tractor age and fuel conception of four models of Farm Tract tractors farmtrac80 (FT80), farmtrac70 (FT70), farmtrac60(ft60) and powertrac55 (PT55). The results showed significant (P> 0.05) differences between repair and maintenance costs in different systems of tractors. It s clear that the fuel conception rate increases as the age of the tractor, but the rate of increases is relatively low at the early stages of the four tractorsselected. Different mathematical regression models were also developed for nature of relationship fuel conception rate (gal/hr) and age of tractor (yrs) for each of the selected. The coefficients of correlation determination for the four tractor selected (FT80), (FT70), (FT60) and (PT55) are 0.97, 0.95, 0.90, and 0.83 respectively, which indicated that fuel conception rate was effected manly by age. This result may be attributed to determination conditions accompanied with increases with age (yrs) or may be due to the frequent fuel system failures because of the worse operation condition. Key words: Maintenance; modeling; fuel conception; Tractor age; 55HP to 80HP. 1. INTRODUCTION Kasmi and Ahmed[1].Stated that fuel and lubricants consumption vary with use of machine. When accurate records are lacking the cost of fuel and lubricants can satisfactory be calculated. They developed a quantitative relationship between diesel fuel consumption, tractor age, annual use, and labor cost for maintenance for different tractor as follows: a) H.M.T zetor 2511: y=2.435-0.06x 1-0.000234x 2 + 0.00015x 3 b) Massy Ferguson 1035: y= 3.201 + 0.039x 1 + 0.00063x 2 0.00053x 3 c) Escort 335: y= 3.215 + 0.011x 1 0.000077x 2 + 0.00041x 3 d) International B 275: y= 4.278 + 0.011x 1 0.0011x 2 + 0.00034x 3 Where: y = Diesel fuel consumption, x 1 = Accumulated hours of use and x 2 = Annual hours of use. They found that Table 1: Multipliers fuel requirements. there highly positive correlation between the age of tractor and the diesel fuel consumption. A negative correlation has been observed between the annual hours, labor cost of maintenance and diesel fuel consumption. Fuel costs depend on the hours of operation and the size of the tractor or power unit. To determine hourly fuel consumption, multiply the tractor power-take-off horsepower by a constant that provides a value in gallons per hour. That value is 0.06 for gasoline engines and 0.044 for diesels [2]. Machinery costs are substantial; control of them is important. Custom charges are often based upon them. No one should do custom work unless the charge will cover operating costs and use-related depreciation plus a return for one's risk and time. Ideally, all allocated per acre or hour overhead costs should also be covered by anyone offering to do custom work. The market for custom work usually does not cover all costs. The market is usually somewhere in between the Use-related costs and total costs[3].prediction of repair and maintenance costs has significant impacts on proper economic decisions making of machinery managers, such as machine s replacement and substitution [4]. (Abdallah F. E [5]. Find that, the mean repair and maintenance cost of the four tractor models showed higher repair and maintenance costs occurred from year 5-10. The engine and hydraulic unit with for more than 60% of the total repair and maintenance cost for tractor FT80 and FT60. In general the difference between four tractors subsystems may be due to the rain fed agricultural areas must be given more breakdowns since the operation condition are different from those of irrigated areas and may be due to variation in soil type. Siemens and Bowers[6].Declared that tractors usually operate at an average of 55% of related power on a year round basis; multipliers have been determined to estimate fuel requirements. These multipliers are listed in the center column in table [1] 65

Engine fuel type Average fuel consumption ( gal/hr/rated P.t.o hp) Typical Ib/gal Gasoline 0.068 6.1 Diesel 0.043 6-9 L.P.Gas 0.080 4.25-4.5 Some mathematical relations were developed in Sudan for repair and maintenance costs estimation for agricultural tractors [7,8and 9].They are varied in structural components due to differences in tractors specifications and conditions and locations of work, therefore, it is difficult to depend on one mathematical model for proper repair and maintenance management decisions. The aims of this study are: (i) to specify the fuel conception for different selected tractor makes. (ii) To develop appropriate mathematical models relating fuel conception and tractor age for four tractor models with different power sizes (iii) to compare the derived model with other models in Sudan. 2. MATERIALS AND METHODS The data of the study was collected from three sites namely Gezira Agricultural scheme, Blue Nile State and North Kordofan State, which are described as follows: 2.1 Gezira Agricultural scheme: It is located in the central clay plain between the Blue Nile and White Nile of the Central Sudan. It is the first largest irrigated scheme and it covers about 9240 Km 2 or 924000 ha. Topographically the area is flat with few isolated small rocky hills [10]. 2.2 Optimization experiments Blue Nile State Table 1: Multipiers fuel requierements. Table 2: Tractors technical specifications. Blue Nile state lies between latitude 9.30 13.34 North with 33.8 35.15 South, approximately in area Of 36,708.5 km 2 included 2500 Km 2 or 252000 Hectares. Good for growing crops. 2.3 North Kordofan State: North KordofanState lies between longitudes 21.2-23 East and 56.30 26 West and latitudes 36.16 16 North and 14 12 South and approximately in an area of 244,700 km2. 2.4 Tractors:There many models of tractors working in the three states under the study. Farm tract 80, farm tract 70, farm tract 60 and power tract 55 tractors are one of the common makes available in these areas and are chosen to carry out this study. The power of these tractors mostly in the range of 45-72hp the total number of the selected tractors for the study is 100 units. The technical specifications of the four tractor models are shown in table 1& Fig 2.Many sources were used to collect data concerning tractor repair and maintenance costs they included Gezira Board, Blue Nile State and North Kordofan State. (Tractor owners companies, agricultural inspectors, mechanics, manufacturer s catalogues and tractors dealers). All these sources were interviewed and some data was collected from the field. 2.5 Data Collection:A direct meeting with customer was prepared to collect the required data then a survey was carried out in the site of the study to interview the target sources of data [5]. Tractor Models Description FT80 FT70 FT60 PT55 Engine power HP (KW) 72.4 HP 60 HP 50 HP 45 Maximum PTO power HP 64 52 48.8 40.8 Maximum torque (kgm) 28.8 @ 1420 RD 21.5 18.2 @ 1166 16.8 RPM RPM 2200 RPM 2200 2000 2000 Engine type 4 stroke, perkins 4 stroke DI 4 stroke / DI 4 stroke / DI Number of cylinders 4 3 3 3 Air cleaner Dual dry/air Dual air cleaner Dry dual plate Dry cleaner Transmission 2WD 2WD 2 WD 2 WD Brakes Oil disc brakes Oil disc brakes Foot operated dry Foot operated dry disc PTO 540 @ 2115 RPM 450 @ 2115 540 @ 1810 540 @ 1810 RPM Cooling system Water cooling Water cooling Water cooling Water cooling Tyres front 7.5 x 16.8 7.5 x 16.8 6.00 x 16 6.00 x 16 Tyres rear 16.9 x 30 16.9 x 28 13.6 x 200 13.6 x 28 Source of data www.scortsagri.com 66

Fig. 1:Farmtrac 80HP [FT80],Farmtrac 70HP [FT70], Farmtrac 60HP [FT60] &Powertrac 55HP [PT55] 2.6 Parameters calculation 2.6.1 Maintenance costs calculation:the annual maintenance which includes, changing oils, greasing, cleaning, changing of filters, and labor cost for maintenance was recorded. The annual maintenance costs were calculated according to market prices of oils, greases, 2.6. 2 Data recording:first of all, it has to be assumed that the data were completely and accurately collected by the company (Danfodio commercial). It s not possible to go back and verify all expenditures; hence the existing records have to be trusted.records of the repair and maintenance costs, including parts, labor, fuel and oil, were available for 200 two-wheel drive (2WD) tractors, over 10 years. These tractors were used for various operations such as tillage, planting and harvesting as well as transportation.the available data contain: monthly usage, monthly repair costs (including parts and labor), monthly maintenance costs (including fuel, oil, fuel filter and oil filter), and year of make purchase and tractor and model. 2.6.3 Tractor age: in this study, we are aiming to provide an effective tool for accurately forecasting fuel consumption of tractors. Tractor age, as well as initial purchase price, can differ considerably among different models of tractor. Despite this variation, it is essential to create the accumulative repair and maintenance costs of different models of tractor relatively. The calendar age is conveniently obtained by subtracting the original purchase date from the current date. Because of natural uncertainties associated with tractor repair and maintenance costs, they do not accrue as a result of elapsed calendar time. Tractor age as cumulative hours of use is a measure of how many hours the tractor physically operated. It dampens many of filters and small adjustments. The accumulated maintenance costs were calculated by summation of the mean annual costs and time for all years for each age model of the selected tractors [11]. the cyclical variations in repair and maintenance costs. The times of oil-change in machines life are usually recorded in terms of a calendar date. Considering the calendar date of the engine oil change and the associated monthly cost data, the cumulative costs for a given number of cumulative hours is determined. 2.6.4 Accumulated repair and maintenance costs computation: The annual repair and maintenance costs for each age model were calculated as follows: Annual repair and maintenance costs = annual repair costs + annual maintenance costs. Tractors of the same models and age were grouped together and the annual repair and maintenance costs of these groups were calculated, then the annual repair and maintenance costs were expressed as percentage of the initial purchase price of the tractor model for the period of study. Statistical analysis was performed using the computer statistical package (SPSS) and excel software to perform the correlation regression relations, Regression analysis of data for all tractors was done using Version, 16.0. Linear, exponential, power and polynomial regression types were tried [12]. 2.6.5 Fuel consumption determination Fuel consumption for the selected tractors was determined records and personal contact with operator in the field. Fuel consumption in gal/fed was calculated as follows: Fuel consumption (gal/fed) = Total consumption in a shift work Total feddans covered in this shift work Then the fuel consumption (gal/fed) were calculated finding out the duration of the shift work in hours. 67

3. RESULTS AND DISCUSSION 3.1 Repair and maintenance costs as affected by tractor age:the accumulated repair(r) and maintenance (M) cost at different age of tractor selected (FT80), (FT70), (FT60) and (PT55) are shown in table [3]. The regression method was used for data analyses and the derivation equations for the four selected tractors makes are shown in table [4] and fig [2]. The accumulated R&M cost was significantly affected by the tractor age and accounted for 99% of the observed variation in age.its observe that the cost of four selected makes increase with age, but with different rate between them FT80 have a higher cost with age followed by FT70 and FT 60 while PT55 showed the least cost throughout. This different between four tractors selected may be due to variation in preventive maintenance and operator skills. In general this high rate of cost with age may be due to attributed to high, higher charges of repair and poorer operation condition. This increases with age of cost agreed with)[9] Table 3: Accumulated R and M costs ($) for different age groups of the four tractors makes. Age (Yrs) Accumulated Rand M COSTS ($) FT 80 FT70 FT 60 PT 55 1-3 748 750 855.2-4-6 1949 971 2071.4 414.6 8-10 2863.6 1821 3348.2 1012.5 Fig. 2: R and M costs ($) as effected by age (yrs) for the selected tractor makes. Table 4: Accumulated R and M costs ($) and tractor age (yrs) equations for the four selected makes. Tractor makes Equation R 2 Multiple R Adjusted R F Sign. F FT80 P= 423.3S 0.9978.99.99.997 1337.3.0000 FT70 P= 336.9S 1.047.99.99.999 10039.7.0000 FT60 P= 380.6S 0.047.99.99.990 10021.3.0000 PT55 P= 9.9262S 2.234.99.99.998 208.2.0441 P= Accumulated R&M cost ($) - S= Tractor age (yrs) 3.2 Accumulated repair rate/1000 hours and age relationships:it sobvious that the accumulated repair rate increases with age but with different amount of the four tractors makes. FT60 showed the highest accumulated repair rate followed by FT 80 and FT 70, while PT55 accounted for the lowest repair rate throughout all selected makes. Regression analyses were used to predict the relationship between accumulated repair rate/1000 hrs and age are shown in table [5].The repair rate was significant affected by the tractor age. This may be attributed to the operators negligence and many breakdowns accompanied with increases of tractor age. The developed models for the selected tractors makes as power function in fig [3]. 68

Table 5:Accumulated repair rate/1000 hrs and tractor age equations for the selected tractors makes. Tractor makes Equation R 2 Multiple R Adjusted R F Sign. F FT80 A= 2.0012G 0.9031.99.99.997 1823.7.0000 FT70 A= 1.9112G 0.047.99.99.999 1523.2.0000 FT60 A= 1.8296G 0.9518.99.99.990 16105.7.0000 PT55 A= 0.0696G 2.337.99.99.993 219.8.0372 A= Accumulated repair rate/1000 hrs - G= Age of tractor (yrs) Fig. 3: the relationship accumulated repair rate/1000 hrs and tractor age for the selected tractors makes. 3.3 Fuel consumption, annual maintenance cost annual hours of use and tractor age relationship: The Fuel consumption against annual maintenance cost ($), annual hours of use and tractor age (yrs) for the four selected tractors are shown in table [6]. It s clear that the fuel consumption rate increases as the age of the tractor increases, but the rate of increase is relatively low at the early stage of the four selected makes. At the firstly years the fuel consumption almost same for FT 80 and FT 70, FT 80 shown the highest rate of fuel consumption (2.13 gal/hr) followed by FT60, FT70 and PT55. The result showed in Table 6: Fuel consumption (gal/hr) for four selected tractors. general, the fuel consumption rate is significant deferent for the four makes may be due to variation in technical specification e.g. engine condition, speed rate and the amount of power available at the drawbar. The confection of correlation determination for the four selected makes FT 80, FT 70, FT 60 and PT 55 are 0.97, 0.95, 0.90, and 0.83 respectively, which indicated that fuel conception rate was affected manly by age. This result may be attributed to determination conditions accompanied with increases with age (yrs) or may be due to the frequent fuel system failures because of the worse operation condition. Age (Yrs) Fuel consumption (gal/hr) FT 80 FT70 FT 60 PT 55 1-3 1.9 1.8 1.05 1.01 4-6 2.0 1.97 1.34 1.22 8-10 2.13 2.11 2.11 1.89 4. CONCLUSION The following conclusions were drawn from the present study: The relationship between repair rate/1000, age (yrs) and fuel consumption as percentage for the four tractor models in the three states (Gezira Agricultural Scheme, Blue Nile State and North Kordofan State) are showed. The fuel consumption rate (gal/hr) of the four selected tractors makes was found greatly affected by tractor age (yrs), annual maintenance cost and annual hour of use. Further studies must be carried out to cover more areas of the country and more tractors makes to achieve precise estimations for repair and maintenance costs for different types of soil under different operations conditions. The governmental companies and schemes that deal with agricultural tractors must concentrate on the effects of repair and maintenance costs determination on the economic life of agricultural tractors, and therefore must keep very precise records about them.thus, the increased competition in agricultural production demands maintenance improvement, aiming at the reduction of 69

maintenance expenditures while keeping the safety of operations. ACKNOWLEDGEMENT The authors would like to thank Department of Agricultural Engineering, Khartoum University for providing financial support.also Danfodio commercial company dealer of Tractors in Sudan. COMPETING INTERESTS Authors declare that they have no competing interests and commercial names and details of machines and equipment s are for the guidelines only. 5. REFERENCES [1] kasmi, R.H. and, Ahmed, T.(1996) Mathematical model for diesel consumption for tractors in Allah-bad District, India, Agricultural Machinery in Asia, Africa and Latin America (AMA),27(3): 73-75. [2] Schuler, R.T. and G.G. Frank,( 1991). Estimating agricultural field machinery costs. Age (years), 1(2): p. 3. [3] LAZARUS, W. F. (2009). Machinery cost estimates. University of Minnesota Extension, St. Paul. [4] Rohani, A. (2011). Prediction of tractor repair and maintenance costs using artificial neural network. Expert Systems with Applications, 38, 8999-9007. [5] Abdallah et al., (2014). Estimation of repair and maintenance cost of a tractor base on HP and working hours: Case study of Sudan. Journal of Environmental and Agricultural Sciences.1:1. [6] Siemens, J.C., W. Bowers, and R.G. Holmes, (1999) Machinery management: how to select machinery to fit the real needs of farm managers: Deere & Company, John Deere Pub. [7] Ahmed, M.H.; Saeed, A.B.; Ahmed, A.H. and Haffar, I. (1999). Tractor repair and maintenance costs in Sudan II: A comparative study among major agricultural schemes. Agricultural Mechanization in Asia, Africa and Latin America (AMA), 30(2): 19-22 [8] Rahma, F.M. (1999). Tractor repair and maintenance cost variability and predictability. UN published M.Sc. Thesis University of Khartoum faculty of agricultural Sudan. [9] Dahab, M.H. and Osama, H.A. (2002). Development of mathematical models for estimation of tractors R&M costs in the main irrigated schemes of the Sudan. University of Khartoum J. Agric. Sciences; 10(2): 251-256. [10] FAO. (1995). (Food and Agricultural Organization).Agricultural mechanization policy and strategy formulation. Sudan Technical Report 1995; TCP/SU/4451. Rome, Italy; 2: 5-22. [11] Ward, S., P. Mculty, P. and M. Cunney. (1985). Repair costs of 2 and 4 WD tractors.transactions of the ASAE-American Society of Agricultural Engineers. [12] Keshavarzpour, F. (2011). Prediction of repair and maintenance costs of Universal 650 Tractors. World Eng. Appl. Sci. J. 2 (4): 31-35.. 70