General Installations Instruktion (Foretages af serviceværksted) Model # SP-1575/SP-1875 Step 1: Take harness assembly and route from the rear of the vehicle to the front. Route harness along frame and attach to frame holes and frame supports. It is not recommended to attach to fuel or brake lines for obvious reasons. Do not route close to exhaust system or engine, even though SnowEx uses high temperature wiring, it still could melt under extreme heat and short the spreader electrical system, as well as the vehicle electrical system. Step 2: Mount rear plug on bumper using supplied bolts, locate towards the center of the bumper to reduce the amount of debris the tires will throw to the rear. Important: Apply a small amount of dielectric grease to the plug. Also try to mount so plug faces upward to help keep plugs Tightly sealed. Step 3: Secure harness from the rear to the front using heavy duty ty-wraps or frame clips along the frame and lighter duty ty-wraps everywhere else. Step 4: Layout harness portion that connects to the battery along the re wall and fender well. Do not connect power leads to battery yet. Drill a 3/4 hole in the fire wall, or use existing access hole, for the control portion of the harness and route connector and harness through hole. Be sure to check the area on the other side of the fire wall to make sure you are not going to drill into the vehicle harness or a control module. Generally you can drill on either side of the steering wheel for a good location. Step 5: Connect harness to the back of the controller and mount to a suitable location. NOTE: You may want to contact customer before mounting controller, some prefer not to have holes drilled into the dashboard. Ty-wrap loose controller harness and move to the engine compartment. Do not mount close to any heater vents. Step 6: Connect power leads to the battery: Red + Positive, Black Negative, always connect to the primary battery if using a dual battery system, secure loose loom to any other large or medium vehicle harness with medium duty ty-wraps; this will secure wiring harness. Step 7: Push the ON/OFF button on the controller to check for power, when that has been conrmed turn power OFF. The electrical portion of the Installation is complete. NOTE: If adding an inline fuse use a 60 amp slow blow (time delay) or a 60 amp relay. De øvrige afsnit er beregnet til serviceværksted.
Control and Harness Diagram Model # SP-1575/SP-1875 4 9 10 1 2 3 IMPORTANT: In the off season remove control and put in a cool dry place. The interior summer temperatures could damage circuit board and void warranty. 5 6 To Vibrator To Auger Motor To Spinner Motor 7 8 will void warranty. Special Notes: 1) All external connections must have dielectric grease. 2) Read lead labels before attaching to power source or ground. 3) No other devices may be spliced into wiring harness. 4) Any repairs to wiring harness must be done with heat shrink butt connectors. 5) If inline fuse is installed, use a 60 amp maxi fuse or circuit breaker. Key Part No. Description Qty 1 D6527 Spreader Control Pro 1 2 D6124 Bracket Knob 2 3 D6329 Controller Mounting Bracket Pro 1 4 D6341 Control Power Cable 156" Pro 1 5 D6322 Vehicle Harness 311" 1 6 D6321 Spreader Harness 38" 1 7 D6343 Dust Cover Pro 1 8 D6170 Connector Adapter 6" Anderson 1 9 D6237 Power Switch 5 Terminal 1 10 D6354 Vibrator Switch 3 Terminal Red 1 11 D6344 Dielectric Grease 1-1/2 oz. 1
Harness Diagram Model # SP-1575/SP-1875 D6322 Vehicle Harness End View White 10 GA Spinner+ Black 10 GA Spinner - Red Black Red 10 GA Auger+ Green 10 GA Auger - Mold Cap Blue 12 GA Vibrator - Orange 10 GA Vibrator - Spinner+ 10 GA White Auger+ 10 GA Red Vibrator+ 12 GA Orange Spinner- 10 GA Black Auger- 10 GA Green Vibrator- 12 GA Blue Hot Circuit Grd Circuit D6341 Control Power Cable 3/8 Terminal w/heat Shrink Black 124 Tubing Red Front View Red to Positive + Black to Negative -
Harness Diagram Model # SP-1575/SP-1875 D6321 Spreader Harness Vibrator Auger Black Leads Male Red Leads Female Spinner Spinner Red Auger Red Vibrator Red Black Black Black D6527 Controller Vibrator Black Negative (-) Vibrator Red Positive (+) Auger Black Negative (-) Auger Red Positive (+) Black Negative (-) Red Positive (+) Spinner Black Negative (-) Spinner Red Positive (+)
Troubleshooting Model # SP-1575/SP-1875 Spreader Does Not Run Controller Turns On Beeps Shuts Off Displays Error Code OL Code Amp Draw Too High Jammed Material Switch Off & On For Auto-Reverse Function Clear Jam Bad Motor Check With Test Kit Test 4 to 20 Amp Draw No Load Good 20+ Amp Draw No Load Bad Bad Transmission Check With Test Kit Test Turn Shaft By Hand Should Turn Freely Corrosion Replace All Corroded Connections Don t Forget Use Doelectric Grease Bad Controller Check With Test Kit EO Code Open Circuit Between Motor And Controller Spreader Unplugged Plug In Spreader Motor Power Cord Disconnected Inside Drive Assembly Open Access Cover And Plug Together Break In Wiring Harness Check With Test Kit Replace Harness LB Code Bad Electrical Connection Corrosion Replace All Corroded Connections Loose Connection Tighten Or Replace Low Battery Less Than 12 Volt Output Load Test Battery E1 Code Dead Short In Motor Circuit Replace Affected Components All Other Codes Check Harness For Spliced In Accessory Bad Controller Check With Test Kit Replace On/Off Switch Lights No Display Check Input Power Bad Controller Check With Test Kit Nothing Happens No Display On/Off Will Not Light Up Check Power Source To Controller Bad Controller Check With Test KIt Snowex Diagnostic Test Kit (STK-080) Is Available To Accurately Diagnose Any Issues With Snowex Spreaders. Call Your Dealer For Details.
Troubleshooting Material Flow Model # SP-1575/SP-1875 Material Free Flows Check Baffle Length 18 Correct Material Issue Check Baffle Position Should Touch Hopper On 3 Sides Material Issue Material Does Not Flow Material Obstruction Remove Obstruction Material Issue Auger Runs Backwards Run 12 Volt To Auger Circuit On Spreader Power Cord Auger Runs Proper Direction Replace Vehicle Harness Turn On Vibrator Auger Runs Backwards Check Connections At Auger Motor For Reverse Polarity Polarity Correct ReplaceSpreader Harness Slow Material Flow Turn On Vibrator Increase Auger Speed Material Issue Snowex Diagnostic Test Kit (STK-080) Is Available To Accurately Diagnose Any Issues With Snowex Spreaders. Call Your Dealer For Details.
Spreader Views Model # SP-1575/SP-1875 SP-1575 SP-1875
Hopper Assembly Parts Breakdown Model # SP-1575 19 8 16 17 9 4 12 10 11 5 1 21 6 15 3 2 7 14 20 18 13
Hopper Assembly Parts Breakdown Model # SP-1575 1 D4122 4 2 D5100 1 3 D5105 1 4 D5110 1 5 D5114 1 6 D5115 1 7 D5706 4 8 D6105 2 9 D6137 2 10 D6140 1 11 D6165 4 12 D6166 4 13 D6169 6 14 D6174 1 15 D6198 2 16 D6240 1 17 D6257 1 18 D6394 2 19 D6553 6 20 D6584 8 21 D6978 4
Frame Assembly Parts Breakdown Model # SP-1575 17 22 8 10 3 14 23 1 23 13 26 6 9 5 12 15 21 20 27 18 7 11 4 25 24 16 2 19
Frame Assembly Parts Breakdown Model # SP-1575 1 D5102 1 2 D5103 1 3 D5107 1 4 D5120 1 5 D5138 1 6 D5139 1 7 D5140 1 8 D5535 4 9 D6107 1 10 D6131 4 11 D6132 4 12 D6165 1 13 D6172 4 14 D6214 2 15 D6232 2 16 D6327 1 17 D6332 1 18 D6333 6 19 D6452 2 20 D6467 6 21 D6566 1 22 D6584 4 23 D6651 2 24 D6746 1 25 D6750 1 26 D6781 2 27 D6874 1
Hitch Parts Breakdown Model # SP-1575 6 5 4 1 7 3 2 8 Note: Always position D4116 (#2) and D4119 (#3) through this hole.
Hitch Parts Breakdown Model # SP-1575 1 D4115 3 2 D4116 1 3 D4119 1 4 D4133 2 5 D4135 1 6 D4136 1 7 D4137 2 8 D5104 1
Hopper Assembly Parts Breakdown Model # SP-1875 10 3 17 14 4 6 18 15 12 1 13 5 11 8 16 7 9 2
Hopper Assembly Parts Breakdown Model # SP-1875 1 D4122 4 2 D4124 4 3 D6105 2 4 D6137 6 5 D6140 1 6 D6169 10 7 D6174 1 8 D6198 2 9 D6313 1 10 D6314 1 11 D6315 1 12 D6328 1 13 D6330 1 14 D6334 1 15 D6337 1 16 D6394 6 17 D6553 6 18 D6584 2
Frame Assembly Parts Breakdown Model # SP-1875 12 17 23 22 5 25 16 24 10 7 27 18 10 21 4 13 6 3 9 15 11 1 20 8 26 14 19
Frame Assembly Parts Breakdown Model # SP-1875 1 D4289 2 2 D6132 8 3 D6133 1 4 D6172 4 5 D6214 2 6 D6225 1 7 D6232 2 8 D6281 1 9 D6317 1 10 D6323 1 11 D6324 1 12 D6325 1 13 D6326 1 14 D6327 1 15 D6331 1 16 D6332 1 17 D6333 14 18 D6356 1 19 D6452 2 20 D6463 2 21 D6501 1 22 D6584 6 23 D6651 1 24 D6652 1 25 D6781 2 26 D6854 2 27 D6877 2