Aerial Units. Contract end Date

Aerial Units Contract end Date 09-30-18 Vendor Name: Altec Industries Inc. Contact Person: Clint Bitting Street Address: 1255 Port Terminal Drive P.O. Box: NA City, State, Zip Duluth, MN 55408 Phone #: 515-240-5342 Toll Free #: 877-GO-ALTEC Fax #: 218-722-6443 Email Address: clint.bitting@altec.com Website: www.altec.com Version of Excel used: 2013 6.0 Aerial Units Make Altec AT37G Standard warranty:one (1) year parts warranty, one (1) year labor warranty, niety (90) days warranty for travel charges, limited lifetime Warranty structural warranty Date & I.D. of Price List 11/27/2017 MN-AT37G-400579-1 Discount to be applied to Price List (see note below) 0.00% Options Use this section to offer options. Add lines as needed 6.1 CVI Inspection NO CHARGE 6.2 Outriggers in lieu of (ILO) torsion bar $ 1,450.00 6.3 AT30G ILO AT37G $ (5,600.00) 6.4 AT40G ILO AT37G (includes 2nd torsion bar) $ 4,500.00 6.5 84" CA fiberglass body ILO 60"CA $ 7,495.00 6.6 Change to 60" CA steel body $ (2,500.00) 6.7 Change to 84" CA steel body $ (2,500.00) 6.8 Body re-configuration $ 840.00 6.9 Toe Space Platform $ 480.00 Delivery SEE SPECIAL TERMS AND CONDITIONS - NO FLAT RATE ALLOWED Delivery Starting Point Address Elizabethtown, KY Price per loaded mile for delivery $ 2.25 Shop Rates Shop Rate for Mechanical work $ 110.00 Body Shop Rate $ 110.00 *Note: The "Discount to be Applied to Price List" must be a numberic percentage. Not listing a numberic percentage may result in your bid being rejected. 6.0 ALTEC Model AT37G telescoping/articulating continuous rotation $58,670.00 Unit Ground to bottom of platform height: 37.8 feet Working height: 42.8 feet

Maximum reach to edge of platform. Side Mounted Platform: 26.6 Telescopic boom extension: 9 feet 8 inches Continuous rotation Insulating Aerial Device, ANSI Category C, 46kV and Below Articulating Arm: Articulation is from -7 to 90 degrees. Insulator Compensation System: By raising the articulating arm only, the Telescoping upper boom: Articulation is from -25 to 75 degrees. Master/ Slave Leveling: Platform automatically maintains level The INSULATING UPPER CONTROL SYSTEM includes a single One set of tool outlets at the platform providing up to 5 gpm of flow Hydraulic System: Open center system operating at 5gpm and Unit is painted with a powder coat paint process which provides a Structural Warranty all of the following applicable major Manuals: Two (2) operator and Maintenance/Parts manuals Engine Start/Stop & Secondary Stowage System: 12 VDC powered Post style pedestal mounting Poly Hydraulic Reservoir, Pedestal Mounted, 7 Gallon (Includes Single, One (1) Man, Fiberglass Platform; End Mounted with 180 One (1) Platform Step Soft nylon reinforced vinyl platform cover for a 24 x 30 inch Platform liner for a 24 x 30 x 42 inch platform Platform Capacity, 400LBS. Altec Patented ISO-Grip Insulating 4 Function, Proportional Speed, Manual lowering valve located at the boom tip. For use in Powder coat unit Altec White. Unit & Hydraulic Acc. HVI-22 Hydraulic Oil (Standard). Standard Pump For PTO Hot shift PTO for automatic transmission Body Altec Osceola Fiberglass body Altec standard fiberglass body specifications: Molded fiberglass side compartments Reinforced, double-laminated doors Heavy duty stainless steel hinges installed on doors Heavy duty strikers installed on body for door latches Automotive-type bulb gasket door seal Corrosion resistant fasteners and self-locking nuts used throughout Extruded aluminum drip rail Fiberglass bulkheads installed between compartments Drains installed in each compartment Body to be vented Aerial service line with step (ASLS) Gelcoat finish entire body Altec white 108 Inch Body Length 39 Inch Body Height (Standard) 94 Inch Body Width (Standard) 20 Inch Body Compartment Depth (Standard) No Treadplate On Compartment Tops 6 Inch tall wood tailboard installed at the rear of body cargo area No Compartment Lighting Supplied by the Body Manufacturer Stainless Steel Rotary Paddle Latch With Lock (Standard) Master Body Locking System (Standard) No Chock Holders In Line Body Fender Panel Required (Standard) Gas Shock Type Rigid Door Holders For Vertical Doors (Standard)

Cable Holders On Horizontal Doors Hotstick shelf extending full length of body on curbside. Drop-Down Hot Stick Door For One (1) Shelf (Right Side) Two (2) Hot Stick Brackets 1st Vertical Street Side (LH) - Two (2) Adjustable Shelf With 1st Horizontal Street Side (LH) - One (1) Fixed Shelf With Rear Vertical Street Side (LH) - Six (6) Adjustable Locking Swivel 1st Vertical Curb Side (RH) - Seven (7) Adjustable Locking Swivel 1st Horizontal Curb Side (RH) - Vacant Rear Vertical Curb Side (RH) - Two (2) Adjustable Shelf With Aluminum Rock Guards Installed at Bottom 38" Tailshelf with Integrated Side Access Steps, Two Wheel Chock Body and Chassis Accessories ICC Underride Protection Combination 2 Ball (10,000 LB MGTW) And Pintle Hitch (16,000 Set Of Eye Bolts for Trailer Safety Chain, installed one each side of Rear Torsion Bar Installed On Chassis Appropriate counterweight added for stability. Platform Rest, Rigid with Rubber Tube Boom Rest for a Telescopic Unit Mud Flaps (Pair) Wheel Chocks, Rubber with Metal Hairpin Style Handle, (Pair) Slope Indicator Assembly For Machine Without Outriggers Safety Harness And 4.5' Lanyard (Fits Medium To X-large) 5 LB Fire Extinguisher With Light Duty Bracket, Ship loose Triangular Reflector Kit Vinyl manual pouch for storage of all operator and parts manuals Electrical Accessories Lights and reflectors in accordance with FMVSS #108 lighting Standard Amber LED Strobe Light With Brush Guard Post Single tone back up alarm installed between the chassis frame rails 6-Way Trailer Receptacle (Pin Type) Installed At Rear Dash panel rocker switches supplied with Chassis. Auxiliary Start/Stop/Throttle Module, 12 Volt System Install secondary stowage system. PTO Indicator Light Installed In Cab Finishing Details Powder Coat Unit Altec White Finish Paint Body Accessories Above Body Floor Altec White Standard; Components mounted below frame rail shall be coated Apply Non-Skid Coating to all walking surfaces English Safety And Instructional Decals Vehicle Height Placard - Installed In Cab Placard, HVI-22 Hydraulic Oil Dielectric test unit according to ANSI requirements. Stability test unit according to ANSI requirements. Install on customer supplied 60 CA Ford F550 or Dodge 5500

Aerial Units Contract end Date 09-30-18 Vendor Name: Altec Industries Inc. Contact Person: Clint Bitting Street Address: 1255 Port Terminal Drive P.O. Box: NA City, State, Zip Duluth, MN 55408 Phone #: 515-240-5342 Toll Free #: 877-GO-ALTEC Fax #: 218-722-6443 Email Address: clint.bitting@altec.com Website: www.altec.com Version of Excel used: 2013 6.0 Aerial Units Make Altec AT41M Standard warranty:one (1) year parts warranty, one (1) year labor warranty, niety (90) days warranty for travel charges, limited lifetime Warranty structural warranty Date & I.D. of Price List 11/27/2017 MN-AT41M-402112-1 Discount to be applied to Price List (see note below) 0.00% Options Use this section to offer options. Add lines as needed 6.1 CVI Inspection NO CHARGE 6.2 Change to AT48 (includes 2nd set of outriggers) $ 7,365.00 6.3 Change to steel body $ (2,500.00) 6.4 Change to Full A-frame outriggers $ 850.00 6.5 Body Compartment re-configure $ 860.00 6.6 24 x 30 Toe Space $ 312.00 6.7 Platform Elevator $ 3,022.00 Delivery SEE SPECIAL TERMS AND CONDITIONS - NO FLAT RATE ALLOWED Delivery Starting Point Address Creedmoor, NC Price per loaded mile for delivery $ 2.00 Shop Rates Shop Rate for Mechanical work $ 110.00 Body Shop Rate $ 110.00 *Note: The "Discount to be Applied to Price List" must be a numberic percentage. Not listing a 6.0 Altec Model AT41M Articulating Telescopic Aerial Device with a Unit $83,880.00 Ground to bottom of platform height: 41 feet Working height: 46 feet Maximum reach to edge of platform. Side Mounted Platform: 30.1 Continuous Rotation Outrigger/boom interlock system prevents boom from being Outrigger/unit selector control is located near the outrigger controls,

Dielectric rating: Category C, 46 kv and below Unit is painted with a powder coat paint process which provides a Manuals: Two (2) Operator s and two (2) Maintenance/ Parts Unit meets or exceeds ANSI 92.2 standards. Pedestal Steel Reservoir, 15 gallon capacity, triangular, 17'' L x 17'' W x 24'' Single 1-Man Platform, Fiberglass (Insulated), 24" x 30" x 42", End Platform Mounted Single Handle Controls Material Handling Jib/Winch, Hydraulically Articulating, Top One(1) Platform step- located on the side of the platform nearest Platform Cover - soft vinyl, 24 x 30 inches (610 x 762 mm) Platform Liner, 24 x 30 x 42 inches (610 x 762 x 1067 mm), 50 kv Hydraulic Tool Circuit at Platform: One set of quick disconnect Engine Start/Stop and secondary stowage Jib Stick, 36"L, non certifies, grey in color Slip Ring: required for engine start/stop and secondary stowage Outriggers, Primary, Modified A-frame with integrated subbase, 30"- Electric Outrigger Controls, drive hydraulic outrigger control valves. Fall Protection System to include one body harness and Lifting Eye - lifting eye at outer end of lower boom. Rated at Winch load line swivel hook Altec Aerial Device Powder Painted White Unit & Hydraulic Acc. HVI-22 Hydraulic Oil (Standard) Standard Pump For PTO Electric Shifted PTO Standard PTO/Transmission Functionality for Small Ford and Body Altec Osceola Fiberglass body Altec standard fiberglass body specifications: Molded fiberglass side compartments Reinforced, double-laminated doors Heavy duty stainless steel hinges installed on doors Heavy duty strikers installed on body for door latches Automotive-type bulb gasket door seal Corrosion resistant fasteners and self-locking nuts used throughout Extruded aluminum drip rail Fiberglass bulkheads installed between compartments Drains installed in each compartment Body to be vented 132'' Body Length 94'' Body Width 39'' Body Compartment Height 20'' Body Compartment Depth 24'' From Body Floor To Compartment Tops 2 x 6 inch drop-in composite retaining board at rear of body. 2 x 6 inch drop-in composite retaining board at side access step. Stainless Steel Rotary paddle Latches With Locks Gas Props On All Vertical Doors Cable Holders On All Horizontal Doors Standard Master Body Locking System Hotstick Shelf Extending Full Length Of Body On Streetside Two (2) Hotstick Brackets On Streetside One Chock Holder On Each Side of Body With Retaining Lip In 1st Vertical (SS) - 34'' W - One (1) Outrigger Housing And Two (2)

2nd Vertical (SS) - 24'' W - Two (2) Adjustable Shelves With 1st Horizontal (SS) - 50'' W - One (1) Fixed Shelf With Removable Rear Vertical (SS) - 24'' W - Six (6) Locking Swivel Hooks On An 1st Vertical (CS) - 34'' W - One (1) Outrigger Housing And Two (2) 2nd Vertical (CS) - 24'' W - Gripstrut Access Steps With Two (2) 1st Horizontal (CS) - 50'' W - One (1) Adjustable Shelf With Rear Vertical (CS) - 24'' W - Six (6) Locking Swivel Hooks On An Body Floor Cut-Out For AT41M Aerial Device Near Front Of Body Aluminum Tailshelf, 29'' L x 94'' W, With Rear Cross Storage And Body and Chassis Accessories ICC Underride Protection T-60 Style Pintle Hitch (10,000 LB MGTW with 2,000 LB MVL) Set Of Eye Bolts for Trailer Safety Chain, installed one each side of Rigid Step Mounted Beneath Side Access Steps (Installed To Extend Platform Rest, Rigid with Rubber Tube Boom Rest for a Telescopic Unit Wood Outrigger Pad, 19'' x 19'' x 2.5'', With Rope Handle Outrigger Pad Holder, 20" L x 20" W x 5" H, Fits 19.5" x 19.5" x 4" A Pendulum Retainers For Outrigger Pad Holders Mud Flaps (Pair) Wheel Chocks, Rubber with Metal Hairpin Style Handle, (Pair) Slope Indicator Assembly For Machine Without Outriggers 5 LB Fire Extinguisher With Light Duty Bracket, Ship loose Triangular Reflector Kit Vinyl manual pouch for storage of all operator and parts manuals Electrical Accessories Lights and reflectors in accordance with FMVSS #108 lighting Standard Amber LED Strobe Light With Brush Guard Post Dual Tone Back-Up With Outrigger Motion Alarm PTO Hour Meter, Digital, with 10,000 Hour Display 6-Way Trailer Receptacle (Pin Type) Installed At Rear Electric Trailer Brake Controller (Tekonsha Voyager #9030) Dash panel rocker switches supplied with Chassis. Auxiliary Start/Stop/Throttle Module, 12 Volt System Install secondary stowage system. Install Remote Start/Stop system in Final Assembly Install Outrigger Interlock System PTO Indicator Light Installed In Cab Finishing Details Powder Coat Unit Altec White Finish Paint Body Accessories Above Body Floor Altec White Standard; Components mounted below frame rail shall be coated Apply Non-Skid Coating to all walking surfaces English Safety And Instructional Decals Vehicle Height Placard - Installed In Cab Placard, HVI-22 Hydraulic Oil Dielectric test unit according to ANSI requirements. Stability test unit according to ANSI requirements. Install on customer supplied 84 CA chassis

Aerial Units Contract end Date 09-30-18 Vendor Name: Altec Industries Inc. Contact Person: Clint Bitting Street Address: 1255 Port Terminal Drive P.O. Box: NA City, State, Zip Duluth, MN 55408 Phone #: 515-240-5342 Toll Free #: 877-GO-ALTEC Fax #: 218-722-6443 Email Address: clint.bitting@altec.com Website: www.altec.com Version of Excel used: 2013 6.0 Aerial Units Make Altec TA50ARM Standard warranty:one (1) year parts warranty, one (1) year labor warranty, niety (90) days warranty for travel charges, limited lifetime Warranty structural warranty Date & I.D. of Price List 11/27/2017 MN-TA50-402116-1 Discount to be applied to Price List (see note below) 0.00% Options Use this section to offer options. Add lines as needed 6.1 CVI Inspection NO CHARGE 6.2 Change to TA55ARM (includes 2nd set of outriggers) $ 14,325.00 6.3 Change to TA60ARM (includes 2nd set of outriggers) $ 17,900.00 6.4 Change to Steel Body $ (2,500.00) 6.5 Body Compartment re-configure $ 900.00 6.6 Automatic Upper Boom Latch $ 850.00 6.7 Add Aux outriggers $ 2,115.00 6.8 Toe Space Platform $ 1,100.00 6.9 Platform Elevator $ 3,025.00 Delivery SEE SPECIAL TERMS AND CONDITIONS - NO FLAT RATE ALLOWED Delivery Starting Point Address St. Joseph, MO Price per loaded mile for delivery $ 2.00 Shop Rates Shop Rate for Mechanical work $ 110.00 Body Shop Rate $ 110.00 *Note: The "Discount to be Applied to Price List" must be a numberic percentage. Not listing a numberic percentage may result in your bid being rejected.

Altec Model TA50 Articulating Telescopic Aerial Device with a fiberglass upper boom and fiberglass insulator in the articulating arm 6.0 and a proportional joystick upper control and toggle switches. Built in accordance to ALTEC's standard specifications and to include the $124,130.00 following features: Unit Ground to bottom of platform height: 50 feet Working height: 55 feet Maximum reach to edge of platform. Side Mounted Platform: 36.2 feet Continuous Rotation Outrigger/boom interlock system prevents boom from being Outrigger/unit selector control is located near the outrigger controls, Dielectric rating: Category C, 46 kv and below Unit is painted with a powder coat paint process which provides a Manuals: Two (2) Operator s and two (2) Maintenance/ Parts manuals containing instructional markings indicating hazards inherent in the operation of an aerial device. Unit meets or exceeds ANSI 92.2 standards. Manual Upper Boom Stow Securing System Pedestal Two-Man Platform (24"x48"x42") with hydraulically articulating jib (Altec ARM Jib) - Platform end mounted, rotates 180 degrees around boom tip. Platform has a capacity of 600lbs without liner. Material handling system comes with 80ft of 0.50 inch polyester double braid rope, a metal thimble in the working end and jib rated at a maximum capacity of 1,000 lbs Platform Mounted Single Handle Controls Material Handling Jib/Winch, Hydraulically Articulating, Top Mounted, Round (ARM Jib) One(1) Platform step- located on the side of the platform nearest the elbow in the stowed position Platform Cover - soft vinyl, 24 x 48 inches Platform Liner, 24 x 48 x 42 inches, 50 kv Rating Tool Circuit At Boom Tip, Dual Hydraulic Engine Start/Stop and secondary stowage Outrigger A-Frame with Flat-shoe - provides 149 inch maximum spread outside to outside of shoe Electric Outrigger Controls, drive hydraulic outrigger control valves. Durable weather proof sealed electronic switches mounted in aluminum boxes located at the rear of the unit unless otherwise specified. Winch load line swivel hook Altec Aerial Device Powder Painted White Unit & Hydraulic Acc. Reservoir, 25 Gallon, Sloped, Mounted in Cargo Area TA Series Subbase HVI-22 Hydraulic Oil (Standard) Standard Pump For PTO Hot shift PTO for automatic transmission Muncie PTO Standard PTO/Transmission Functionality for Automatic Body Altec Osceola

Fiberglass body Altec standard fiberglass body specifications: Molded fiberglass side compartments Reinforced, double-laminated doors Heavy duty stainless steel hinges installed on doors Heavy duty strikers installed on body for door latches Automotive-type bulb gasket door seal Corrosion resistant fasteners and self-locking nuts used throughout Extruded aluminum drip rail Fiberglass bulkheads installed between compartments Drains installed in each compartment Body to be vented Aerial service line with step (ASLS) Gelcoat finish entire body Altec white 160 inch overall body length. 94 inch overall body width. 48 inch overall body height. 18 inch body compartment depth. 2 x 6 inch drop-in composite retaining board at rear of body. 2 x 6 inch drop-in composite retaining board at side access step. Stainless Steel Rotary Paddle Latches With Keyed Locks All Locks Keyed Alike Including Accessories (Preferred Option) Standard Master Body Locking System, For Use With An Access Step Gas Shock (Gas Spring) Rigid Door Holders On All Vertical Doors One Chock Holder On Each Side of Body With Retaining Lip In Fender Panel Fiberglass Hotstick Shelf Extending Full Length Of Body On Streetside Two Hotstick Brackets On Streetside Standard Drop-Down Fiberglass Hotstick Door For One (1) Shelf On Streetside, Stainless Steel Slam Paddle Latch With Keyed Lock 3/16" Aluminum Treadplate Floor 4" Steel Channel Body Frame Bolt Down Aluminum Floor To Steel Frame 1st vertical streetside (LH) - Six (6) locking swivel hooks on adjustable rails. 2-2-2 configuration. 2nd vertical streetside (LH) - Six (6) locking swivel hooks on adjustable rails. 2-2-2 configuration. 3rd vertical streetside (LH) - Six (6) locking swivel hooks on adjustable rails. 2-2-2 configuration. 1st horizontal streetside (LH) - One (1) adjustable shelf with removable dividers on 4 inch centers. Rear vertical streetside (LH) - Two (2) adjustable shelves with removable dividers on 4 inch centers. 1st vertical curbside (RH) - Two (2) adjustable shelves with removable dividers on 4 inch centers. 2nd vertical curbside (RH) - Gripstrut access steps with two (2) sloped grab handles.

3rd vertical curbside (RH) - Six (6) locking swivel hooks on adjustable rails. 2-2-2 configuration. 1st horizontal curbside (RH) - Two (2) adjustable shelves with removable dividers on 8 inch centers. Rear vertical curbside (RH) - Six (6) locking swivel hooks on adjustable rails. 2-2-2 configuration. Curbside compartment top access step installed in the cargo area behind side access step. 29 inch long x 94 inch wide aluminum tailshelf, two (2) U-shaped grab handles, installed at rear of body. Aluminum Tailshelf, 29'' L x 94'' W, With Rear Cross Storage And Drop Down Doors Body and Chassis Accessories ICC Underride Protection T-125 Style Pintle Hitch (30,000 LB MGTW with 6,000 LB MVL) Set Of Eye Bolts for Trailer Safety Chain, installed one each side of towing device mount. Rigid Step Mounted Beneath Side Access Steps (Installed To Extend Approx. 2'' Outward) Platform Access Step From Body Floor Platform Rest, Rigid with Rubber Tube Boom Rest for a Telescopic Unit Wood Outrigger Pad, 19'' x 19'' x 2.5'', With Rope Handle Outrigger Pad Holder, 20" L x 20" W x 5" H, Fits 19.5" x 19.5" x 4" And Smaller Pads, Bolt-On, Bottom Washout Holes, 3/4" Lip Retainer Pendulum Retainers For Outrigger Pad Holders Mud Flaps (Pair) Wheel Chocks, Rubber with Metal Hairpin Style Handle, (Pair) Slope Indicator Assembly For Machine Without Outriggers 5 LB Fire Extinguisher With Light Duty Bracket, Ship loose Triangular Reflector Kit Fall Protection kit Vinyl manual pouch for storage of all operator and parts manuals Electrical Accessories Lights and reflectors in accordance with FMVSS #108 lighting Standard Amber LED Strobe Light With Brush Guard Post Mounted Dual Tone Back-Up With Outrigger Motion Alarm Altec Standard Multi-Point Grounding System Copper U Shaped Grounding Lug (Threaded) Installed on CS front and rear 7-Way Trailer Receptacle (Pin Type) Installed At Rear Electric Trailer Brake Controller (Tekonsha Voyager #9030) Start/Stop/Throttle Module, 12 Volt System Install secondary stowage system. Install Remote Start/Stop system in Final Assembly Install Outrigger Interlock System Altec Modular Panel System (AMPS) - Includes Mounting Panel and Finishing Details Powder Coat Unit Altec White Finish Paint Body Accessories Above Body Floor Altec White Standard; Components mounted below frame rail shall be coated

Apply Non-Skid Coating to all walking surfaces English Safety And Instructional Decals Vehicle Height Placard - Installed In Cab Placard, HVI-22 Hydraulic Oil Dielectric test unit according to ANSI requirements. Stability test unit according to ANSI requirements. Install on customer supplied 84 CA chassis

Aerial Units Contract end Date 09-30-18 Vendor Name: Altec Industries Inc. Contact Person: Clint Bitting Street Address: 1255 Port Terminal Drive P.O. Box: NA City, State, Zip Duluth, MN 55408 Phone #: 515-240-5342 Toll Free #: 877-GO-ALTEC Fax #: 218-722-6443 Email Address: clint.bitting@altec.com Website: www.altec.com Version of Excel used: 2013 6.0 Aerial Units Make Altec AN55E-OC Standard warranty:one (1) year parts warranty, one (1) year labor warranty, niety (90) days warranty for travel charges, limited lifetime Warranty structural warranty Date & I.D. of Price List 11/27/2017 MN-AN55-402139-1 Discount to be applied to Price List (see note below) 0.00% Options Use this section to offer options. Add lines as needed CVI Inspection NO CHARGE 6.1 AN46E-OC $ (2,425.00) 6.2 Change to AN50E-OC $ (1,210.00) 6.3 Change to steel body $ (2,500.00) 6.4 Body Compartment re-configure $ 925.00 6.5 Platform Elevator $ 3,760.00 6.6 Change to AME model $ 2,980.00 6.6 Toe Space Platform $ 1,100.00 Delivery SEE SPECIAL TERMS AND CONDITIONS - NO FLAT RATE ALLOWED Delivery Starting Point Address Ronaoke, VA Price per loaded mile for delivery $ 2.00 Shop Rates Shop Rate for Mechanical work $ 110.00 Body Shop Rate $ 110.00 *Note: The "Discount to be Applied to Price List" must be a numberic percentage. Not listing a numberic percentage may result in your bid being rejected. Altec Model AN55E-OC Articulating Overcenter Aerial Device with a fiberglass upper boom and fiberglass insulator in the lower boom 6.0 and a proportional joystick upper control and toggle switches. Built $126,995.00 in accordance to ALTEC's standard specifications and to include the following features: Unit

Ground to bottom of platform height: 55 feet Working height: 60 feet Maximum reach to edge of platform. 43.1 feet Continuous Rotation Outrigger/boom interlock system prevents boom from being unstowed until outriggers have been at least partially deployed Outrigger/unit selector control is located near the outrigger controls, allows operator to divert hydraulic oil from machine circuit for outrigger operation. This reduces the potential for inadvertent outrigger movement during machine operation if outrigger controls are bumped Dielectric rating: Category C, 46 kv and below Unit is painted with a powder coat paint process which provides a finish-painted surface that is highly resistant to chipping, scratching, abrasion and corrosion. Paint is electrostatically applied to the inside as well as outside of fabricated parts then high temperature cured prior to assembly ensuring maximum coverage and protection. Manuals: Two (2) Operator s and two (2) Maintenance/ Parts Unit meets or exceeds ANSI 92.2 standards. Automatic upper boom stow system Pedestal Two-Man Platform (24"x48"x42") Platform is rated at 700 pounds (317.5 kg) and rotates 90 degrees to end of boom. Includes two sets of quick disconnect couplings and controls for hydraulic tools. Includes hydraulically articulating and extending material handling jib with winch and rope mounted on opposite side of upper boom.-- Material handling jib capacity is in addition to platform capacity. Jib and winch system includes hydraulic tool lines in boom to furnish 8.0 gpm at 2,000 psi (30.3 lpm/13 800 kpa) and includes: Material handling, hydraulically articulated jib, -30 degree to +90 degree tilt angle (relative to the upper boom). Jib also extends from 43 to 67 inches ( 1092 x 1702 mm) in five pinning positions. One (1) piece 4.0 inch (101.6 mm) square jib Hydraulically powered winch rated to 2,000 pounds (907.2 kg) full drum, mounted on the side of the upper boom 80 feet of 7/16 inch (24.4 m of 11.1 mm) double-braided synthetic rope Control valves at platform for hydraulic tools, platform rotation, jib tilt, jib extend and winch control Auxiliary winch line control valve and platform rotation valve at the turntable to allow rescue Valve at boom tip relieves pressure from quick disconnect couplings in Off position. Open-center or closed-center tools may be operated from tool circuit Fiberglass covers Primary Outrigger X-Frame with flat shoe - 172.8 inch max spread Auxillary Outrigger A-Frame with Flat-shoe - provides 149 inch Platform Cover - soft vinyl, 24 x 48 inches Platform Liner, 24 x 48 x 42 inches, 50 kv Rating Tool Circuit At Boom Tip, Dual Hydraulic Engine Start/Stop and secondary stowage Electric Outrigger Controls, drive hydraulic outrigger control valves.

Winch load line swivel hook Altec Aerial Device Powder Painted White Unit & Hydraulic Acc. Reservoir, 30 Gallon, Triangular, Mounted in Cargo Area AN Series Subbase HVI-22 Hydraulic Oil (Standard) Standard Pump For PTO Hot shift PTO for automatic transmission Muncie PTO Standard PTO/Transmission Functionality for Automatic Body Altec Osceola Fiberglass body Altec standard fiberglass body specifications: Molded fiberglass side compartments Reinforced, double-laminated doors Heavy duty stainless steel hinges installed on doors Heavy duty strikers installed on body for door latches Automotive-type bulb gasket door seal Corrosion resistant fasteners and self-locking nuts used throughout Extruded aluminum drip rail Fiberglass bulkheads installed between compartments Drains installed in each compartment Body to be vented Aerial service line with step (ASLS) Gelcoat finish entire body Altec white 170 inch overall body length 94 inch overall body width. 48 inch overall body height. 18 inch body compartment depth. 2 x 6 inch drop-in composite retaining board at rear of body. 2 x 6 inch drop-in composite retaining board at side access step. Gas shock type rigid door holders for vertical doors. Standard master body locking system. Cable holders on all horizontal doors One (1) wheel chock holder installed in fender panel on each side of body. Hotstick shelf extending from rear of first vertical to rear of body on streetside. Two (2) hotstick brackets installed on street side. Large side hinged hotstick door for multiple shelves on streetside. 1st vertical street side (LH) - Three (3) adjustable shelves with removable dividers on 4 inch centers. 2nd vertical street side (LH) - Six (6) locking swivel hooks on adjustable rails. 1-4-1 configuration. 3rd vertical street side (LH) - Six (6) locking swivel hooks on adjustable rails. 1-4-1 configuration. 1st horizontal street side (LH) - One (1) fixed shelf extending through rear vertical. Rear vertical street side (LH) - Outrigger housing. 1st vertical curb side (RH) - Three (3) adjustable shelves with removable dividers on 4 inch centers.

2nd vertical curb side (RH) - Six (6) locking swivel hooks on adjustable rails. 1-4-1 configuration. 3rd vertical curb side (RH) - Gripstrut access steps with two (2) sloped grab handles. 1st horizontal curb side (RH) - Two (2) adjustable shelves with removable dividers on 8 inch centers. Rear Vertical curb side (RH) - Five (5) locking swivel hooks on fixed rails. 1-3-1 configuration. Rear Vertical curb side (RH) - Outrigger housing. Curbside compartment top access step installed in the cargo area 7 inches behind side access step. 24 inch long x 94 inch wide aluminum tailshelf with 3 inch high retainer rail around sides and rear, installed at rear of body. Body and Chassis Accessories ICC Underride Protection T-125 Style Pintle Hitch (30,000 LB MGTW with 6,000 LB MVL) Set Of Eye Bolts for Trailer Safety Chain, installed one each side of towing device mount. Rigid Step Mounted Beneath Side Access Steps (Installed To Extend Approx. 2'' Outward) Compartment Top Access Step from Body Floor Platform Access Step From Body Floor Single Platform Access, One Step Mounted to Turntable Platform Rest, Rigid with Rubber Tube Lower boom rest weldment Wood Outrigger Pad, 19'' x 19'' x 2.5'', With Rope Handle Outrigger Pad Holder, 20" L x 20" W x 5" H, Fits 19.5" x 19.5" x 4" And Smaller Pads, Bolt-On, Bottom Washout Holes, 3/4" Lip Retainer Pendulum Retainers For Outrigger Pad Holders Mud Flaps (Pair) Wheel Chocks, Rubber with Metal Hairpin Style Handle, (Pair) Slope Indicator Assembly For Machine Without Outriggers 5 LB Fire Extinguisher With Light Duty Bracket, Ship loose Triangular Reflector Kit Fall Protection kit Vinyl manual pouch for storage of all operator and parts manuals Electrical Accessories Lights and reflectors in accordance with FMVSS #108 lighting Standard Amber LED Strobe Light With Brush Guard Post Dual Tone Back-Up With Outrigger Motion Alarm Altec Standard Multi-Point Grounding System Copper U Shaped Grounding Lug (Threaded) Installed on CS front and rear 7-Way Trailer Receptacle (Pin Type) Installed At Rear Electric Trailer Brake Controller (Tekonsha Voyager #9030) Start/Stop/Throttle Module, 12 Volt System Install secondary stowage system. Install Remote Start/Stop system in Final Assembly Install Outrigger Interlock System Altec Modular Panel System (AMPS) - Includes Mounting Panel and Accessory Switches

Finishing Details Powder Coat Unit Altec White Finish Paint Body Accessories Above Body Floor Altec White Standard; Components mounted below frame rail shall be coated black by Altec. Apply Non-Skid Coating to all walking surfaces English Safety And Instructional Decals Vehicle Height Placard - Installed In Cab Placard, HVI-22 Hydraulic Oil Dielectric test unit according to ANSI requirements. Stability test unit according to ANSI requirements. Install on customer supplied chassis

Aerial Units Contract end Date 09-30-18 Vendor Name: Altec Industries Inc. Contact Person: Clint Bitting Street Address: 1255 Port Terminal Drive P.O. Box: NA City, State, Zip Duluth, MN 55408 Phone #: 515-240-5342 Toll Free #: 877-GO-ALTEC Fax #: 218-722-6443 Email Address: clint.bitting@altec.com Website: www.altec.com Version of Excel used: 2013 6.0 Aerial Units Make Altec LR7-60 Standard warranty:one (1) year parts warranty, one (1) year labor warranty, niety (90) days warranty for travel charges, limited lifetime Warranty structural warranty Date & I.D. of Price List 11/27/2017 MN-LR7-402140-1 Discount to be applied to Price List (see note below) 0.00% Options Use this section to offer options. Add lines as needed 6.1 CVI Inspection NO CHARGE 6.2 LR7-56 $ (1,315.00) 6.3 Rear Mount Version $ 11,330.00 6.4 Toe Space Platform $ 480.00 Delivery SEE SPECIAL TERMS AND CONDITIONS - NO FLAT RATE ALLOWED Delivery Starting Point Address Creedmoor, NC Price per loaded mile for delivery $ 2.00 Shop Rates Shop Rate for Mechanical work $ 110.00 Body Shop Rate $ 110.00 *Note: The "Discount to be Applied to Price List" must be a numberic percentage. Not listing a numberic percentage may result in your bid being rejected. ALTEC Model LR7-60 Articulating Overcenter Aerial Device with an 6.0 insulating lower boom, insulating upper boom and the Altec ISO- $82,240.00 Grip insulating system at the boom tip installed behind the cab to include the following features: Unit Ground to bottom of platform height: 60 feet Working height: 65 feet Maximum reach to edge of platform. Side Mounted Platform: 48.4 feet

Continuous Rotation Outrigger/boom interlock system prevents boom from being unstowed until outriggers have been at least partially deployed Outrigger/unit selector control is located near the outrigger controls, allows operator to divert hydraulic oil from machine circuit for outrigger operation. This reduces the potential for inadvertent outrigger movement during machine operation if outrigger controls are bumped Unit is painted with a powder coat paint process which provides a Manuals: Two (2) Operator s and two (2) Maintenance/ Parts Unit meets or exceeds ANSI 92.2 standards. Manual Upper Boom stow system Pedestal Single, One (1) Man, Fiberglass Platform; fixed side mounted. 24 x 24 x 39 inches. One(1) Platform step- located on the side of the platform nearest Platform Cover - soft vinyl, 24 x 24 inches Platform Liner, 24 x 24 x 39 inches, 50 kv Rating Tool Circuit At Boom Tip, Dual Hydraulic Engine Start/Stop and secondary stowage Primary Outrigger A-Frame with swivel-shoes Hydraulic Outrigger Control Valves Altec Aerial Device Powder Painted White Unit & Hydraulic Acc. Reservoir, 30 Gallon, Sloped, Mounted in Cargo Area, with sight ga HVI-22 Hydraulic Oil (Standard) Standard Pump For PTO Hot shift PTO for automatic transmission Muncie PTO Standard PTO/Transmission Functionality for Automatic Transmissions -If chassis is in gear, and PTO switch is activated, PTO will not engage. Chassis will remain in gear. Once the chassis is shifted back into gear the PTO will disengage. For some truck configurations the PTO switch must be turned off to allow the transmission to shift into gear. Body Altec Chip Dump Body 14.5 cubic yard capacity, 96 inches wide x 60 inches high x 132 inches long (2438 x 1524 x 3353 mm) with ladder box on curb side of body and single piece tailgate Structural Channel stringers and floor channel. 12 gauge minimum floor plate. 14 gauge minimum sides and front with full length die-formed reinforcing ribs. 14 gauge roof. Rear top and sides of body reinforced for lower boom support. 26-1/2 inches (673 mm) high tailgate, hinged curb side with provision to hold open for dumping.

12 gauge minimum rear under body skirt panel. Class ''C'' Hydraulic hoist, installed, with 45 degree dump angle and body prop. LED lighting package, security-mounted, with wiring harness in automotive type loom. Two(2) LED strobes mounted in the upper rear corners of the dump body. Curb side built-in ladder compartment, 12 inches wide x 25 inches high (305 x 635 mm) with wear pad and internal security chain. Pole pruner compartment, 11 inches high (279.4 mm), above ladder compartment with dual shelves and rear locking door. Upper section of rear door opening is open. Interior of chip body finished with scratch and corrosion resistant liner Underside of chip body undercoated. Painted White Altec T-66 Thru Box with curbside and streetside compartments containing the following: Streetside: Single compartment (66 inches long x 50 inches high x 26.5 inches deep) with two (2) barn-style doors and one (1) vertical door. Two (2) full width shelves fixed at 11 inches and 25 inches from top. Rubber matting (0.125 inch thick) in bottom on left side for chainsaw storage. Right side has access to horizontal thru compartment extending to curbside.. Curbside: Single compartment (41 inches long x 50 inches high x 26.5 inches deep) with two (2) barn-style doors. Left side has two (2) full width shelves fixed at 11 inches and 25 inches from top. Right side has six (6) material hooks (3-0-3). Platform mounted behind compartment 12 inches high x 25 inches wide x 26.5 inches deep. Horizontal thru compartment (6 inches high) recessed 12 inches, open to streetside with vertical partitions spaced 10 inches, Standard features: Bolt-on rotary slam door locks. Gas shock door holders. Door locks are single point with locking cylinders. Finish paint interior compartments the same as exterior. Integrated locking system installed. Provide flat plate across top of transverse for walking surface Painted White Body and Chassis Accessories Cab Guard, 140'' L, 12 GA Sheet Metal With Non-Skid Surface And Expanded Metal Section At Front, Black Gator Hyde Coating ICC Underride Protection T-100 Style Pintle Hitch (30,000 LB) Set Of Loops for Trailer Safety Chain, installed one each side of towing device mount. Cab Guard Access Stirrup Step(s) With Grab Handle(s) At Curbside Rear Of Cab Guard Rigid Access Step Under Through Box Side Access Platform Platform Rest, Rigid with Rubber Tube Wood Outrigger Pad, 19'' x 19'' x 2.5'', With Rope Handle

Outrigger Pad Holder, 20" L x 20" W x 5" H, Fits 19.5" x 19.5" x 4" And Smaller Pads, Bolt-On, Bottom Washout Holes, 3/4" Lip Retainer Pendulum Retainers For Outrigger Pad Holders Mud Flaps (Pair) Wheel Chocks, Rubber with Metal Hairpin Style Handle, (Pair) Slope Indicator Assembly For Machine Without Outriggers 5 LB Fire Extinguisher With Light Duty Bracket, Ship loose Triangular Reflector Kit Fall Protection kit Vinyl manual pouch for storage of all operator and parts manuals Electrical Accessories Lights and reflectors in accordance with FMVSS #108 lighting Standard Amber LED Strobe Light With Brush Guard Post Dual Tone Back-Up With Outrigger Motion Alarm 6-Way Trailer Receptacle (Pin Type) Installed At Rear Electric Trailer Brake Controller (Tekonsha Voyager #9030) Install Outrigger Interlock System Altec Modular Panel System (AMPS) - Includes Mounting Panel and Accessory Switches Finishing Details Powder Coat Unit Altec White Finish Paint Body Accessories Above Body Floor Altec White Standard; Components mounted below frame rail shall be coated Apply Non-Skid Coating to all walking surfaces English Safety And Instructional Decals Vehicle Height Placard - Installed In Cab Placard, HVI-22 Hydraulic Oil Dielectric test unit according to ANSI requirements. Stability test unit according to ANSI requirements. Install on customer supplied chassis

Body Options Contract end Date 09-30-18 Vendor Name: Altec Industries Inc. Contact PersonClint Bitting Street Address: 1255 Port Terminal Drive P.O. Box: NA City, State, Zip Duluth, MN 55408 Phone #: 515-240-5342 Toll Free #: 877-GO-ALTEC Fax #: 218-722-6443 Email Address: clint.bitting@altec.com Website: www.altec.com Version of Excel used: 2013 11.0 STORAGE BOXES AND OPTIONS Make Altec Warranty 1 year Date & I.D. of Price List 11/27/2017 MN-OPTIONS10052016 Discount to be applied to Price List (see note below) 0.00% Installation of storage box and/or option as per MnDOT spec 8.0 see list below Delivery SEE SPECIAL TERMS AND CONDITIONS - NO FLAT RATE ALLOWED Delivery Starting Point Address Duluth, MN Price per loaded mile for delivery $2.25 Shop Rate per Hour Shop Rate for Mechanical work $ 110.00 Body Shop Rate $ 110.00 *Note: The "Discount to be Applied to Price List" must be a numberic percentage. Not listing a numberic percentage may result in your bid being rejected. 11.0 OPTIONS 11.1 Custom Boom Color $ 3,000.00 11.2 Custom Body Color $ 500.00 11.3 Subbase Storage (NA for AT37G or LR7) $ 1,269.60 COMPARTMENT LIGHTS installed in Body Compartments (LED 11.4 Rope Style) (Per Compartment) $ 216.00 PURE SINE WAVE INVERTER.1800 Watts Continuous. 100-11.5 VAC Outlet at Rear of Body. $ 1,976.40 PURE SINE WAVE INVERTER.2400 Watts Continuous. GFCI 11.6 Outlet at Rear. $ 2,356.80 PURE SINE WAVE INVERTER.3400 Watts Continuous. GFCI 11.7 Outlet at Rear. $ 3,321.60 11.8 Cone Holder installed $ 140.40 11.9 4 corner strobe lighting installed $ 552.00 11.10 120 volt outlet installed $ 210.00 11.11 Lower tool circuit $ 346.80 11.12 Remote Controlled Spotlight installed $ 652.20 11.13 4" round cargo light installed $ 175.20 11.14 4" round grommet mounted strobe light installed $ 312.00 11.15 LED work light installed $ 116.40 11.16 Directional Light Bar installed $ 747.60

PD18 Front bumper winch package( only avialable on TA, AN, 11.17 and LR7 units) installed $ 6,921.60 11.18 Platform leveling at lower controls $ 350.00 11.19 Glad Hands installed $ 144.00 11.20 Dock Bumpers installed $ 145.20 11.21 PTO Hour Meter installed $ 132.00 11.22 Set of 3 Compartment hooks $ 82.80 11.23 Standard compartment shelf $ 117.60 11.24 3x3 equipto drawer kit installed $ 403.20 11.25 Full width pullout drawer installed $ 198.00 Top opening Aluminum treadplate box with gas props 3ft long or 11.26 less, installed $ 1,117.20 Top opening Aluminum treadplate box with gas props 3ft-6ft long, 11.27 installed $ 1,333.20 Top opening Aluminum treadplate box with gas props greater 11.28 than 6ft long, installed $ 1,900.80 11.29 Underslung storage box, aluminum treadplate, drop down door $ 1,173.60 11.30 Custom control handle configuration $ 100.00 11.31 Throttle Control $ 300.00 11.32 12,0000lb electric winch for AT $ 2,965.20 11.33 Cold Weather oil (per gallon) $ 32.40 11.34 Back up camera installed $ 840.00 11.35 D-rings, installed $ 192.00 11.36 Change AT37G to track mounted model aerial device with auger $ 87,330.00 11.37 platform lighting system $ 400.00 11.37 E-track installed per foot $ 12.00