Technical Data 7 Effective December 05 Supersedes October 05 USSMNN SERIES HE breakaway and non-breakaway in-line fuse holders for UL 3/3 x -/ supplemental fuses Symbol: HE* Description: The ussmann series of HE submersible, single-pole in-line fuse holders for UL 3/3 x -/ supplemental fuses. vailable in non-breakaway and breakaway versions with an array of options to meet application needs. reakaway versions come with insulating boots to provide submersibility per UL IP67. Non-breakaway versions require ordering optional insulating boots for submersibility. Recommended fuses: F, FNM, FNQ, KLM and KTK Ratings: Volts: 600V mps: up to 30 limited by conductor size Withstand: 00k RMS Sym. gency information: UL Recognized, Guide IZLT, File E4853 CS Certified, Class 650, File 4735 CE, RoHS compliant Coupling nut torque: 0-0 Lb-In (.-. Nm) Operating and storage temperature: -40 F (-40 C) to F (05 C) Insulating boots: Two insulating boots come standard with the breakaway holder configurations. Insulating boots are not included as standard with nonbreakaway holders. Two insulating boots must be ordered separately, if required, for each nonbreakaway holder ordered. When insulating boots are utilized, extra heat retention requires that fuses are sized at a minimum of 00% of the RMS load current. Use these part numbers to order insulating boots for a non-breakaway HE holder: Description Part number Single conductor 0660 Dual conductor 066 oot reference: Installation instructions: Strip wire insulation equal to the depth of the crimp or screw. Torque screw to 35 Lb-In (3.9 Nm) or crimp twice, spacing crimps a distance of one-third from each end (as shown below) using an appropriate crimp tool and die. See page 6 for recommended crimping tools. Related products: 4. (04) 4.7 (9) Crimp twice at locations /3 distance from each end Strip wire insulation to depth of number Description HEX Two-pole supplemental in-line fuse holder HEZ One-pole Class CC in-line fuse holder HEY Two-pole Class CC in-line fuse holder One-pole in-line, HET permanently installed neutral NN 3/3 x -/ neutral dummy link (not a fuse) 0.8 (ø0).3 (ø33) Data sheet No. 6 30 6 5 * The ussmann series HE in-line fuse holders are the legacy ussmann TRON HE in-line fuse holders. See data tables for exceptions.
Technical Data 7 Effective December 05 ussmann series HE breakaway and non-breakaway in-line fuse holders for UL 3/3 x -/ supplemental fuses Non-breakaway catalog number system HE - To order: Specify catalog HE and the loadside code. Then select a lineside code that is available with the loadside. Example: HE- defines a non-breakaway holder with a loadside copper crimp for a single or two #0 wires with a lineside copper crimp for a single or two #0 wires. HE Loadside Lineside gency Information Loadside Lineside Reference UL CS X X X X C X X D X X J X K X R L W Y X X X X C X X D X X W C C X X D D X X () #0 () #0 () #0 () #0 () #0 () #8 # str; () () #0 () #8 # str; () length reakaway equivalent 4.4 () HE-W-RLC- 4.4 () HE-W-RLC- 4.7 (9) HE-W-RLC-C 4.7 (9) Cu #3-4.7 (9) HE-W-RLC-J #- 4.8 () HE-W-RYC l crimp #- 4.9 (4) l #- 4.7 (9) HE-W-RL Cu solid 4.4 () l dual #- 4.8 () HE-W-RY () #0 () #8 # str; () 4.4 () HE-W-RLC- 4.4 () HE-W-RLC- 4.7 (9) 4.7 (9) Cu solid 4.4 () Z #8-0 J J X Cu K X Cu L Cu W Cu Y Cu () #8 # str; () 5 (7) 5 (7) 4.4 () #3- Cu #3-5 (7) HE-JW-RLC-J #3- #- 5. (9) HE-JW-RYC #3- l #- 5 (7) #3- Cu solid 4.8 () #3- l dual #- 5. (9) * /stranded conductors unless otherwise noted. Non-breakaway dimensions - in (mm): 9.5 (3) ssembled length
ussmann series HE breakaway and non-breakaway in-line fuse holders for UL 3/3 x -/ supplemental fuses Technical Data 7 Effective December 05 Non-breakaway catalog number system HE - HE Loadside Lineside gency Information Loadside Lineside Reference UL CS L L l N N l crimp P P X l crimp Q Q X l crimp #- 6 sol; 8 str 4 sol; 6 str # sol; #3-4 str l l crimp l crimp l crimp length reakaway equivalent #- 5 (7) HE-LW-RL sol; #8 str #4 sol; str # sol; #3-4 str 5.4 (37) 5.4 (37) 5.4 (37) R R X l crimp #- str l crimp #- str 5.4 (37) T T X l crimp /0 str l crimp /0 str 5.4 (37) W W Cu solid Cu solid 4.4 () * /stranded conductors unless otherwise noted. Non-reakaway data #8-6 #0-6 #0 #4 #8 # [Load /Line] C D #8-0 Z l crimp #8 #4 #3-4 # [Load /Line] #- R N P Q Cu Cu solid #3- J #- K W l l dual #/0 T #- L #- Y Fuse holder assemblies using this are not RoHS compliant. 3
Technical Data 7 Effective December 05 ussmann series HE breakaway and non-breakaway in-line fuse holders for UL 3/3 x -/ supplemental fuses reakaway catalog number system HE - W - RYC Loadside Lineside gency Information Loadside Lineside Length UL CS RLC- X X To order: Specify catalog HE and the loadside code plus the letter W. Then select a lineside code that is available with the loadside. Example: HE-W-RCL- defines a breakaway holder with a loadside copper crimp for a single or two #0 wires with a lineside copper crimp for a single or two #0 wires. (reference) Nonbreakaway equivalent 5.8 (47) HE- RLC- X () #0 5.9 (50) HE- RLC-C X () #8 6. (58) HE-C RLC-J X Cu #3-6. (58) HE-J RYC X #- 6.3 (59) HE-K RL l #- 6. (58) HE-L RY l dual #- 6.3 (59) HE-Y RLC- X () #0 5.8 (47) HE- HE RLC- X () #0 6#; () #0 5.9 (50) HE- RYC X () #0 #- 6.3 (59) J RLC-J X Cu RYC X Cu #3- #3- Cu #3-6. (58) HE-JJ #- 6.3 (59) HE-JK K RLC-J X RYC X #- Cu #- #3-6. (58) #- 6.3 (59) RL l #- l #- 6. (58) HE-LL L RLC-J l #- Cu #3-6. (58) RY l #- l dual #- 6.3 (59) * /stranded conductors unless otherwise noted. Dimensions - in (mm): reakaway 0.375 (63) ssembled length 4
ussmann series HE breakaway and non-breakaway in-line fuse holders for UL 3/3 x -/ supplemental fuses Technical Data 7 Effective December 05 reakaway loadside data reakaway lineside data #8-6 #0-6 [Load /Line () & (3)] #8-6 #-6 -RLC- #0 #0 #4 #8 -RLC- -RLC- C Cu #3- J Cu #3- -RLC-J #- K #- -RYC l l #- -RL #- L l dual #- -RY Fuse holder assemblies using this are not RoHS compliant. 5
Technical Data 7 Effective October 05 ussmann series HE breakaway and non-breakaway in-line fuse holders for UL 3/3 x -/ supplemental fuses Recommended crimping tools: wide variety of crimping tools can be used with the HE fuse holders. Some of the commercially available tools are listed in the table below. This list is not intended to exclude the use of other crimping tools that can provide similar crimps or indents. HE T & P/N (Die) WT-M (Die C) Sta-Kon ERG400 (Die C) WT-5 (Die D) TM5 (Grey Die) C WT-5 (Die E) TM5 (rown Die) D TM8 (rown Die) WT-5 (Die F) WT-M (Die ) Z Sta-Kon ERG400 (Die ) N, P, Q, R, T TM8 (Orange Die) The only controlled copy of this data sheet is the electronic read-only version located on the Eaton network drive. ll other copies of this document are by definition uncontrolled. This bulletin is intended to clearly present comprehensive product data and provide technical information that will help the end user with design applications. Eaton reserves the right, without notice, to change design or construction of any products and to discontinue or limit distribution of any products. Eaton also reserves the right to change or update, without notice, any technical information contained in this bulletin. Once a product has been selected, it should be tested by the user in all possible applications. Eaton 000 Eaton oulevard Cleveland, OH 44 Eaton.com ussmann Division 4 Old State Road Ellisville, MO 630 United States 05 Eaton ll Rights Reserved Printed in US Publication No. 7 - U-S554 December 05 Eaton, ussmann and Tron are valuable trademarks of Eaton in the US and other countries. You are not permitted to use the Eaton trademarks without prior written consent of Eaton. CS is a registered trademark of the Canadian Standards Group. Sta-Kon is a registered trademark of Thomas & etts. UL is a registered trademark of the Underwriters Laboratories, Inc.