n 119 kw (159 hp)
EnginE Manufacturer and Model... Isuzu 4HK1 Non-Road Emission Standards... certified to IT4 / Stage IIIB emissions Net Rated Power (ISO 9249)... 119 kw (159 hp) @ 1,900 rpm Cylinders... 4 Displacement... 5.2 L (317 cu. in.) Off Level Capacity... 70% (35 deg.) Aspiration... turbocharged, air-to-air charge air cooler Cooling Direct-driven, high-efficiency, low-noise, suction-type fan PowErtrain 2-speed propel with automatic shift Maximum travel Speed Low... 3.5 km/h (2.2 mph) High... 5.5 km/h (3.4 mph) Drawbar Pull... 20 700 kg (45,636 lb.) HydrauliCS Open center, load sensing Main Pumps... 2 variable-displacement axial-piston pumps Maximum Rated Flow... 212 L/m (56 gpm) x 2 Pilot Pump... one gear Maximum Rated Flow... 30.0 L/m (7.9 gpm) Pressure Setting... 3999 kpa (580 psi) System operating Pressure Implement Circuits... 34 336 kpa (4,980 psi) Travel Circuits... 34 336 kpa (4,980 psi) Swing Circuits... 34 336 kpa (4,980 psi) Power Boost... 38 000 kpa (5,511 psi) Controls... pilot levers, short stroke, low-effort hydraulic pilot controls with shutoff lever CylindErS Bore rod diameter Stroke Boom (2)... 120 mm (4.72 in.) 85 mm (3.35 in.) 1260 mm (49.61 in.) Arm (1)... 135 mm (5.31 in.) 95 mm (3.74 in.) 1475 mm (58.07 in.) Bucket (1)... 115 mm (4.53 in.) 80 mm (3.15 in.) 1060 mm (41.73 in.) ElECtriCal Number of Batteries (12 volt)... 2 Battery Capacity... 1,400 CCA Alternator Rating... 50 amp Work Lights... 2 halogen (one mounted on boom, one on frame) undercarriage ZX210-5 ZX210lC-5 roller (each side) Carrier Rollers (per side)... 2 2 Track Rollers (per side)... 7 8 Shoes (per side)... 46 49 track Adjustment... hydraulic hydraulic Guides... center center Chain... sealed and lubricated sealed and lubricated 2
Ground Pressure ZX210-5 ZX210LC-5 600 mm (24-in.) Triple Semi-Grouser Shoes... 45 kpa (6.53 psi) 47.9 kpa (6.95 psi) 700 mm (28-in.) Triple Semi-Grouser Shoes... 39 kpa (5.66 psi) 41.7 kpa (6.05 psi) 800 mm (32-in.) Triple Semi-Grouser Shoes... 34 kpa (4.93 psi) 36.9 kpa (5.35 psi) swing MeChanisM Swing Speed... 13.3 rpm Swing Torque... 68 900 Nm (50,662 lb.-ft.) serviceability refill Capacities Fuel Tank... 403 L (106.5 gal.) Cooling System... 25 L (26.4 qt.) Engine Oil with Filter... 23 L (24 qt.) Hydraulic Tank... 135 L (35.7 gal.) Hydraulic System... 240 L (63.4 gal.) Swing Gearbox... 6.2 L (6.6 qt.) Propel Gearbox (each)... 7.8 L (8.2 qt.) Pump Drive Gearbox... 1 L (1.1 qt.) operating weights ZX210-5 ZX210LC-5 With Full Fuel Tank; 79-kg (175-lb.) operator; 666-kg (1,468-lb.) general-purpose bucket; 2.91-m (9-ft. 7-in.) arm; 4250-kg (9,370-lb) counterweight, and 800-mm (32-in.) triple semi-grouser shoes. Operating Weight... 20 800 kg (45,815 lb.) 21 400 kg (47,137 lb.) optional Components Undercarriage with Triple Semi-Grouser Shoes 600 mm (24 in.) Triple Semi-Grouser Shoes... 6752 kg (14,873 lb.) 7353 kg (16,196 lb.) 700 mm (28 in.) Triple Semi-Grouser Shoes... 7143 kg (15,733 lb.) 7743 kg (17,055 lb.) 800 mm (32 in.) Triple Semi-Grouser Shoes... 7437 kg (16,381 lb.) 8038 kg (17,705 lb.) One-Piece Boom (with arm cylinder)... 1732 kg (3,815 lb.) 1732 kg (3,815 lb.) Arm with Bucket Cylinder and Linkage 2.22 m (7 ft. 3 in.)... 928 kg (2,044 lb.) 928 kg (2,044 lb.) 2.91 m (9 ft. 7 in.)... 990 kg (2,181 lb.) 990 kg (2,181 lb.) Boom Lift Cylinders (2) Total Weight... 341 kg (751 lb.) 341 kg (751 lb.) 1065-mm (42-in.), 0.91-m³ (1.19-cu. yd.) Heavy-Duty Bucket. 886 kg (1,952 lb.) 886 kg (1,952 lb.) Counterweight Standard... 4250 kg (9,361 lb.) 4250 kg (9,361 lb.) ZX210-5 operating dimensions arm Length 2.42 m (7 ft. 11 in.) 2.91 m (9 ft. 7 in.) Arm Digging Force (SAE)... 133 kn (29,901 lb.) 110 kn (24,730 lb.) (ISO)... 140 kn (31,475 lb.) 114 kn (25,629 lb.) Bucket Digging Force (SAE)... 141 kn (31,700 lb.) 141 kn (31,700 lb.) (ISO)... 158 kn (35,522 lb.) 158 kn (35,522 lb.) Lifting Capacity Over Front at Ground Level 6.1-m (20-ft.) Reach (with Power Boost)... 5,919 kg (13,050 lb.) 5,919 kg (13,050 lb.) a Maximum Reach... 9.43 m (30 ft. 11 in.) 9.92 m (32 ft. 7 in.) a' Maximum Reach at Ground Level... 9.25 m (30 ft. 4 in.) 9.75 m (31 ft. 12 in.) b Maximum Digging Depth... 6.18 m (20 ft. 3 in.) 6.68 m (21 ft. 11 in.) b' Maximum Digging Depth at 2.44-m (8-ft.) Flat Bottom... 5.95 m (19 ft. 6 in.) 6.50 m (21 ft. 4 in.) C Maximum Cutting Height... 9.67 m (31 ft. 9 in.) 10.04 m (32 ft. 11 in.) d Maximum Dumping Height... 6.83 m (22 ft. 5 in.) 7.18 m (23 ft. 7 in.) e Minimum Swing Radius... 3.28 m (10 ft. 9 in.) 3.18 m (10 ft. 5 in.) F Maximum Vertical Wall... 5.3 m (17 ft. 5 in.) 5.99 m (19 ft. 8 in.) G Tail Swing Radius... 2.89 m (9 ft. 6 in.) 2.89 m (9 ft. 6 in.) C D B B F GROUND LINE A A E CENTERLINE OF SWING G 3
ZX210LC-5 Operating DimensiOns arm Length 2.42 m (7 ft. 11 in.) 2.91 m (9 ft 7 in.) Arm Digging Force (SAE)... 133 kn (29,901 lb.) 110 kn (24,730 lb.) (ISO)... 140 kn (31,475 lb.) 114 kn (25,629 lb.) Bucket Digging Force (SAE)... 141 kn (31,700 lb.) 141 kn (31,700 lb.) (ISO)... 158 kn (35,522 lb.) 158 kn (35,522 lb) Lifting Capacity Over Front at Ground Level 6.1-m (20-ft.) Reach (with Power Boost)... 6,849 kg (15,100 lb.) 6,849 kg (15,100 lb.) a Maximum Reach... 9.43 m (30 ft 11 in.) 9.92 m (32 ft. 7 in.) a' Maximum Reach at Ground Level... 9.25 m (30 ft. 4 in.) 9.75 m (31 ft. 12 in.) B Maximum Digging Depth... 6.18 m (20 ft. 3 in.) 6.68 m (21 ft. 11 in.) B' Maximum Digging Depth at 2.44-m (8-ft.) Flat Bottom... 5.95 m (19 ft. 6 in.) 6.50 m (21 ft. 4 in.) C Maximum Cutting Height... 9.67 m (31 ft. 9 in.) 10.04 m (32 ft. 11 in.) D Maximum Dumping Height... 6.83 m (22 ft. 5 in.) 7.18 m (23 ft. 7 in.) e Minimum Swing Radius... 3.28 m (10 ft. 9 in.) 3.18 m (10 ft. 5 in.) F Maximum Vertical Wall... 5.3 m (17 ft. 5 in.) 5.99 m (19 ft. 8 in.) g Tail Swing Radius... 2.89 m (9 ft. 6 in.) 2.89 m (9 ft. 6 in.) C D B B F GROUND LINE A A E CENTERLINE OF SWING G machine DimensiOns ZX210-5 ZX210LC-5 a Overall length 2.42 m (7-ft. 11-in.) arm... 9.75 m (31 ft. 12 in.) 9.75 m (31 ft. 12 in.) Overall length 2.91 m (9-ft. 7-in.) arm... 9.53 m (31 ft. 3 in.) 9.53 m (31 ft. 3 in.) B Overall Height 2.42 m (7-ft. 11-in.) arm... 3.18 m (10 ft. 5 in.) 3.18 m (10 ft. 5 in.) Overall Height 2.91 m (9-ft. 7-in.) arm... 3.01 m (9 ft. 11 in.) 3.01 m (9 ft. 11 in.) C Rear-End Length/Swing Radius... 2.89 m (9 ft. 6 in.) 2.89 m (9 ft. 6 in.) D Distance Between Idler/Sprocket Centerline... 3.35 m (10 ft. 12 in.) 3.67 m (12 ft.) e Undercarriage Length... 4.17 m (13 ft. 8 in.) 4.46 m (14 ft. 8 in.) F Counterweight Clearance... 1030 mm (3 ft. 5 in.) 1030 mm (3 ft. 5 in.) g Upperstructure Width... 2.71 m (8 ft. 11 in.) 2.71 m (8 ft. 11 in.) h Cab Height... 2.95 m (9 ft. 8 in.) 2.95 m (9 ft. 8 in.) i Track Width with Triple Semi-Grouser Shoes... 600 mm (24 in.) 600 mm (24 in.)... 700 mm (28 in.) 700 mm (28 in.)... 800 mm (32 in.) 800 mm (32 in.) J Gauge Width... 2.39 m (7 ft. 10 in.) 2.39 m (7 ft. 10 in.) K Ground Clearance... 450 mm (18 in.) 450 mm (18 in.) L Overall Width With Triple Semi-Grouser Shoes 600 mm (24 in.)... 2.99 m (9 ft. 10 in.) 2.99 m (9 ft. 10 in.) 700 mm (28 in.)... 3.09 m (10 ft. 2 in.) 3.09 m (10 ft. 2 in.) 800 mm (32 in.)... 3.19 m (10 ft. 6 in.) 3.19 m (10 ft. 6 in.) G C H B F K J L I A D E 4
LIFT CHARTS ZX210-5 Boldface type indicates hydraulically limited capacity; lightface type indicates stability-limited capacities, in kg (lb.). Ratings at bucket lift hook; machine equipped with 666-kg (1,468-lb.) bucket; standard gauge; and situated on firm, uniform supporting surface. Total load includes weight of cables, hook, etc. Figures do not exceed 87 percent of hydraulic capacities or 75 percent of weight needed to tip machine. All lift capacities are based on ISO 10567 (with power boost). Load Point Height 1.5 m (5 ft.) 3.0 m (10 ft.) 4.5 m (15 ft.) 6.0 m (20 ft.) 7.5 m (25 ft.) Horizontal Distance Over Over Over Over Over Over Over Over Over Over from Centerline Front Side Front Side Front Side Front Side Front Side of Rotation With 2.91-m (9-ft. 7-in.) arm and 700-mm (28-in.) shoes 6.0 m (20 ft.) 4700 4450 (10,300) (9,500) 4.5 m (15 ft.) 6150 6150 5250 4300 4500 2850 (13,250) (13,250) (11,450) (9,250) (9,600) (6,150) 3.0 m (10 ft.) 8050 6400 6150 4050 4400 2800 (17,350) (13,800) (13,350) (8,750) (9,450) (5,950) 1.5 m (5 ft.) 9800 5950 6150 3850 4300 2700 (21,100) (12,800) (13,200) (8,250) (9,200) (5,750) Ground Line 4150 4150 9500 5650 5950 3700 4200 2600 (9,650) (9,650) (20,400) (12,200) (12,800) (7,900) (9,000) (5,600) 1.5 m ( 5 ft.) 4800 4800 8400 8400 9400 5600 5850 3600 4150 2550 (10,750) (10,750) (19,100) (19,100) (20,200) (12,050) (12,650) (7,750) (8,950) (5,550) 3.0 m ( 10 ft.) 9250 9250 13 950 11 150 9500 5650 5900 3650 (20,850) (20,850) (30,250) (23,950) (20,350) (12,150) (12,750) (7,850) 4.5 m ( 15 ft.) 10 850 10 850 7650 5850 (23,150) (23,150) (16,250) (12,650) With 2.91-m (9-ft. 7-in.) arm and 800-mm (32-in.) 6.0 m (20 ft.) 4700 4500 (10,300) (9,650) 4.5 m (15 ft.) 6150 6150 5250 4350 4600 2950 (13,250) (13,250) (11,450) (9,400) (9,800) (6,250) 3.0 m (10 ft.) 8050 6500 6150 4150 4500 2850 (17,350) (14,050) (13,350) (8,950) (9,650) (6,100) 1.5 m (5 ft.) 9800 6050 6250 3900 4350 2750 (21,100) (13,000) (13,450) (8,450) (9,400) (5,850) Ground Line 4150 4150 9700 5750 6050 3750 4300 2650 (9,650) (9,650) (20,800) (12,450) (13,050) (8,050) (9,200) (5,700) 1.5 m ( 5 ft.) 4800 4800 8400 8400 9600 5700 6000 3700 4250 2650 (10,750) (10,750) (19,100) (19,100) (20,600) (12,250) (12,900) (7,900) (9,150) (5,650) 3.0 m ( 10 ft.) 9250 9250 13 950 11 350 9650 5750 6050 3700 (20,850) (20,850) (30,250) (24,350) (20,750) (12,400) (13,000) (8,000) 4.5 m ( 15 ft.) 10 850 10 850 7650 5950 (23,150) (23,150) (16,250) (12,850) 5
LIFT CHARTS ZX210LC-5 Boldface type indicates hydraulically limited capacity; lightface type indicates stability-limited capacities, in kg (lb.). Ratings at bucket lift hook; machine equipped with 666-kg (1,468-lb.) bucket; standard gauge; and situated on firm, uniform supporting surface. Total load includes weight of cables, hook, etc. Figures do not exceed 87 percent of hydraulic capacities or 75 percent of weight needed to tip machine. All lift capacities are based on ISO 10567 (with power boost). Load Point Height 1.5 m (5 ft.) 3.0 m (10 ft.) 4.5 m (15 ft.) 6.0 m (20 ft.) 7.5 m (25 ft.) Horizontal Distance Over Over Over Over Over Over Over Over Over Over from Centerline Front Side Front Side Front Side Front Side Front Side of Rotation With 2.42-m (7-ft. 11-in.) arm and 800-mm (32-in.) 6.0 m (20 ft.) 5200 4950 (11,450) (10,600) 4.5 m (15 ft.) 6850 6850 5750 4850 (20,650) (20,650) (14,800) (14,800) (12,450) (10,400) 3.0 m (10 ft.) 8750 7200 6550 4600 5150 3200 (18,800) (15,550) (14,150) (9,950) (11,000) (6,850) 1.5 m (5 ft.) 10 250 6750 7200 4400 5050 3100 (22,100) (14,550) (15,450) (9,500) (10,800) (6,700) Ground Line 10 750 6550 7050 4250 4950 3050 (23,300) (14,150) (15,100) (9,200) (10,650) (6,550) 1.5 m ( 5 ft.) 9150 9150 10 450 6550 7000 4250 (21,050) (21,050) (22,600) (14,100) (15,050) (9,100) 3.0 m ( 10 ft.) 12 800 12 800 9250 6650 6650 4300 (27,750) (27,750) (20,000) (14,300) (14,200) (9,300) 4.5 m ( 15 ft.) 6400 6400 (13,250) (13,250) With 2.91-m (9-ft. 7-in.) arm and 600-mm (24-in.) 6.0 m (20 ft.) 4700 4700 (10,300) (10,300) 4.5 m (15 ft.) 6150 6150 5250 4700 4850 3150 (13,250) (13,250) (11,450) (10,150) (10,650) (6,750) 3.0 m (10 ft.) 8050 7100 6150 4500 4950 3100 (17,350) (15,250) (13,350) (9,650) (10,600) (6,600) 1.5 m (5 ft.) 9800 6600 6900 4250 4800 2950 (21,100) (14,200) (14,900) (9,150) (10,350) (6,400) Ground Line 4150 4150 10 650 6300 6750 4100 4700 2900 (9,650) (9,650) (23,050) (13,600) (14,500) (8,800) (10,150) (6,200) 1.5 m ( 5 ft.) 4800 4800 8400 8400 10 600 6250 6650 4000 4700 2850 (10,750) (10,750) (19,100) (19,100) (23,000) (13,400) (14,300) (8,600) (10,100) (6,150) 3.0 m ( 10 ft.) 9250 9250 13 950 12 700 9750 6300 6700 4050 (20,850) (20,850) (30,250) (27,150) (21,050) (13,550) (14,400) (8,700) 4.5 m ( 15 ft.) 10 850 10 850 7650 6500 (23,150) (23,150) (16,250) (14,050) With 2.91-m (9-ft. 7-in.) arm and 700-mm (28-in.) shoes 6.0 m (20 ft.) 4700 4700 (10,300) (10,300) 4.5 m (15 ft.) 6150 6150 5250 4800 4850 3250 (13,250) (13,250) (11,450) (10,350) (10,650) (6,950) 3.0 m (10 ft.) 8050 7250 6150 4600 5050 3150 (17,350) (15,600) (13,350) (9,850) (10,850) (6,750) 1.5 m (5 ft.) 9800 6750 7050 4350 4950 3050 (21,100) (9,350) (15,200) (9,350) (10,600) (6,550) Ground Line 4150 4150 10 650 6450 6900 4200 4850 2950 (9,650) (9,650) (23,050) (13,900) (14,850) (9,000) (10,400) (6,350) 1.5 m ( 5 ft.) 4800 4800 8400 8400 10 600 6400 6800 4100 4800 2950 (10,750) (10,750) (19,100) (19,100) (23,000) (13,750) (14,650) (8,850) (10,350) (6,350) 3.0 m ( 10 ft.) 9250 9250 13 950 12 950 9750 6450 6850 4150 (20,850) (20,850) (30,250) (27,750) (21,050) (13,900) (14,750) (8,950) 4.5 m ( 15 ft.) 10 850 10 850 7650 6650 (23,150) (23,150) (16,250) (14,350) 6
LIFT CHARTS ZX210LC-5 (ConTInued) Boldface type indicates hydraulically limited capacity; lightface type indicates stability-limited capacities, in kg (lb.). Ratings at bucket lift hook; machine equipped with 666-kg (1,468-lb.) bucket; standard gauge; and situated on firm, uniform supporting surface. Total load includes weight of cables, hook, etc. Figures do not exceed 87 percent of hydraulic capacities or 75 percent of weight needed to tip machine. All lift capacities are based on ISO 10567 (with power boost). Load Point Height 1.5 m (5 ft.) 3.0 m (10 ft.) 4.5 m (15 ft.) 6.0 m (20 ft.) 7.5 m (25 ft.) Horizontal Distance Over Over Over Over Over Over Over Over Over Over from Centerline Front Side Front Side Front Side Front Side Front Side of Rotation With 2.91-m (9-ft. 7-in.) arm and 800-mm (32-in.) shoes 6.0 m (20 ft.) 4700 4700 (10,300) (10,300) 4.5 m (15 ft.) 6150 6150 5250 4900 4850 3300 (13,250) (13,250) (11,450) (10,500) (10,650) (7,050) 3.0 m (10 ft.) 8050 7350 6150 4650 5150 3200 (17,350) (15,850) (13,350) (10,050) (11,050) (6,900) 1.5 m (5 ft.) 9800 6850 7050 4450 5050 3100 (21,100) (14,750) (15,200) (9,550) (10,800) (6,700) Ground Line 4150 4150 10 650 6600 7050 4250 4950 3000 (9,650) (9,650) (23,050) (14,150) (15,100) (9,150) (10,650) (6,500) 1.5 m ( 5 ft.) 4800 4800 8400 8400 10 600 6500 6950 4200 4900 3000 (10,750) (10,750) (19,100) (19,100) (23,000) (14,000) (14,950) (9,000) (10,600) (6,450) 3.0 m ( 10 ft.) 9250 9250 13 950 13 200 9750 6550 7000 4200 (20,850) (20,850) (30,250) (28,200) (21,050) (14,150) (15,050) (9,100) 4.5 m ( 15 ft.) 10 850 10 850 7650 6800 (23,150) (23,150) (16,250) (14,600) BuCkeT SeLeCTIon GuIde* A full line of buckets is offered to meet a wide variety of applications. Digging forces are with power boost. Buckets are equipped with ESCO teeth standard. Replaceable cutting edges and a variety of teeth are available through Hitachi parts. Optional side cutters add 150 mm (6 in.) to bucket widths. Capacities are SAE heaped ratings. Type Bucket Bucket Width Bucket Capacity Bucket Weight Bucket dig Force Arm dig Force Arm dig Force Bucket Tip Radius number 2.42 m (7 ft. 11 in.) 2.91 m (9 ft. 7 in.) of Teeth mm in. m 3 cu. yd. kg lb. kn lb. kn lb. kn lb. mm in. Heavy Duty 915 36 0.69 0.9 708 1,559 135.9 30,554 130.2 29,271 107.1 24,071 1463 57.61 5 Heavy Duty 1065 42 0.83 1.09 786 1,731 135.9 30,554 130.2 29,271 107.1 24,071 1463 57.61 5 Heavy Duty 1220 48 0.99 1.29 872 1,921 135.9 30,554 130.2 29,271 107.1 24,071 1463 57.61 6 Heavy Duty High Capacity 610 24 0.43 0.56 646 1,424 135.0 30,349 129.9 29,197 106.8 24,016 1473 58 4 Heavy Duty High Capacity 760 30 0.58 0.76 723 1,593 135.0 30,349 129.9 29,197 106.8 24,016 1473 58 4 Heavy Duty High Capacity 915 36 0.74 0.97 809 1,782 135.0 30,349 129.9 29,197 106.8 24,016 1473 58 5 Heavy Duty High Capacity 1065 42 0.91 1.19 886 1,951 135.0 30,349 129.9 29,197 106.8 24,016 1473 58 5 2.7 (3.5) 3 BUCKET SIZE m (cu. yd.) 2.3 (3.0) 1.9 (2.5) 1.5 (2.0) 1.0 (1.5) Hitachi 2.42-m (7-ft. 11-in.) Arm Hitachi 2.91-m (9-ft. 7-in.) Arm 0.8 (1.0) lb./cu. yd. 1,200 1,400 1,600 1,800 2,000 2,200 2,400 2,600 2,800 3,000 3,200 3,400 3,600 kg/m 3 700 800 900 1000 1100 1200 1300 1400 1500 1600 1700 1800 1900 2000 2100 Wet Peat Topsoil Coal Caliche Shale Dry Sand Dry Clay Limestone Wet Earth Wet Clay, Granite Moist Sand Wet Sand Wet Sand, Gravel * Contact your Hitachi dealer for optimum bucket and attachment selections. These recommendations are for general conditions and average use. Does not include optional equipment such as thumbs or couplers. Larger buckets may be possible when using light materials, for flat and level operations, less compacted materials, and volume loading applications such as mass-excavation applications in ideal conditions. Smaller buckets are recommended for adverse conditions such as off-level applications, rocks, and uneven surfaces. Bucket capacity indicated is SAE heaped. 7
ADDITIONAL EQUIPMENT KEy: l Standard s Optional or special See your Hitachi dealer for further information. ENgINE l Auto-idle system l Batteries (2 12 volt) l Coolant recovery tank l Dual-element dry-type air filter l Electronic engine control l Enclosed fan guard (conforms to SAE J1308) l Engine coolant to 37 deg. C ( 34 deg. F) l Fuel filter with water separator l Full-flow oil filter l Turbocharger with charge air cooler l 500-hour engine-oil-change interval l 70% (35 deg.) off-level capability l Engine-oil-sampling valve l Programmable auto shutdown HyDrAULIc SySTEM l Reduced-drift valve for boom down, arm in l Auxiliary hydraulic valve section l Spring-applied, hydraulically released automatic swing brake l Auxiliary hydraulic-flow adjustments through monitor l Auto power lift l 5,000-hour hydraulic-oil-change interval l Hydraulic-oil-sampling valve s Auxiliary hydraulic lines s Auxiliary pilot and electric controls s Hydraulic filter restriction indicator kit s Load-lowering control device s Single-pedal propel control s Control pattern-change valve UNDErcArrIAgE l Planetary drive with axial piston motors l Propel motor shields l Spring-applied, hydraulically released automatic propel brake l Track guides, front idler and center l 2-speed propel with automatic shift l Upper carrier rollers (2) l Sealed and lubricated track chain s Triple semi-grouser shoes, 600 mm (24 in.) s Triple semi-grouser shoes, 700 mm (28 in.) s Triple semi-grouser shoes, 800 mm (32 in.) UPPErSTrUcTUrE l Right-hand, left-hand, and counterweight mirrors l Vandal locks with ignition key: Cab door / Service doors / Toolbox l Debris screen l Remote-mounted engine oil and fuel filters FrONT ATTAcHMENTS l Centralized lubrication system l Dirt seals on all bucket pins l Less boom and arm l HN bushings l Reinforced resin thrust plates l Tungsten carbide thermal coating on arm-to-bucket joint s Arm, 2.42 m (7 ft. 11 in.) s Arm, 2.91 m (9 ft. 7 in.) s Attachment quick-couplers s Boom cylinder with plumbing to mainframe for less boom and arm s Buckets: Ditching / Heavy duty / Heavy-duty high capacity / Side cutters and teeth s Material clamps s Super-long fronts OPErATOr S STATION l Meets ISO 12117-2 for ROPS l Adjustable independent-control positions (levers-to-seat, seat-to-pedals) l AM/FM radio l Auto climate control/air conditioner/heater/pressurizer l Built-in Operator s Manual storage compartment and manual l Cell-phone power outlet, 12 volt, 60 watt, 5 amp l Coat hook l Deluxe suspension cloth seat with 100-mm (4 in.) adjustable armrests l Floor mat l Front windshield wiper with intermittent speeds l Gauges (illuminated): Engine coolant / Fuel l Horn, electric l Hour meter, electric l Hydraulic shutoff lever, all controls l Hydraulic warm-up control l Interior light l Large cup holder OPErATOr S STATION (continued) l Machine Information Center (MIC) l Mode selectors (illuminated): Power modes (3) / Travel modes (2 with automatic shift) / Work mode (1) l Multifunction, color LCD monitor with: Diagnostic capability / Multiple-language capabilities / Maintenance tracking / Clock / System monitoring with alarm features: Auto-idle indicator, engine air cleaner restriction indicator light, engine check, engine coolant temperature indicator light with audible alarm, engine oil pressure indicator light with audible alarm, lowalternator-charge indicator light, low-fuel indicator light, fault code alert indicator, fuel-rate display, wiper-mode indicator, work-lights-on indicator, and work-mode indicator l Motion alarm with cancel switch (conforms to SAE J994) l Power-boost switch on right console lever l Auxiliary hydraulic control switches in right console lever l SAE 2-lever control pattern l Seat belt, 51 mm (2 in.), retractable l Tinted glass l Transparent tinted overhead hatch l Hot/cold beverage compartment s Air-suspension heated seat s 24- to 12-volt D.C. radio convertors, 10 amp s Hydraulic oil filter restriction indicator light s Protection screens for cab front, rear, and side s Seat belt, 76 mm (3 in.), non-retractable s Window vandal-protection covers ELEcTrIcAL l 50-amp alternator l Blade-type multi-fused circuits l Positive-terminal battery covers l ZXLink wireless communication system (available in specific countries; see your dealer for details) s Rearview camera s Cab extension wiring harness LIgHTS l Work lights: Halogen / One mounted on boom / One mounted on frame s 2 lights mounted on cab / One mounted on right side of boom Net engine power is with standard equipment including air cleaner, exhaust system, alternator, and cooling fan, at test conditions specified per ISO 9249. No derating is required up to 2000-m (6,560-ft.) altitude. Specifications and design subject to change without notice. Wherever applicable, specifications are in accordance with SAE standards. Except where otherwise noted, these specifications are based on units with 2.91-m (9 ft. 7 in.) arms; 1065-mm (42 in.), 0.91-m 3 (1.19 cu. yd.), 886-kg (1,951 lb.) heavy-duty buckets; 4250-kg (9,361 lb.) counterweights; full fuel tanks; and 79-kg (175 lb.) operators; and a 210LC-5 unit with 800-mm (32-in.) triple semi-grouser shoes. DKZX210HT5 Litho in U.S.A. (12-04) Hitachi Construction and Mining Products 1515 5th Avenue Moline, IL 61265 www.hitachiconstruction.com