GRUNDFOS DATA BOOKLET CRIE10-03 A-FGJ-I-E-HQQE 3x380-500 60 HZ Grundfos pump 98390289 Thank you for your interest in our products. Please contact us for more information, or visit our website https://www.lenntech.com/grundfos/crie10/98390289/crie-10-3-a-fgj-i-e-hqqe.html info@lenntech.com tel. +31 152 610 900 fax. +31 152 616 289 BE > THINK > INNOVATE
Position Qty. Description 1 CRIE 10-3 A-FGJ-A-E-HQQE Product No.: On request Vertical, multistage centrifugal pump with inlet and outlet ports on same the level (inline). Pump materials in contact with the liquid are in stainless steel. A cartridge shaft seal ensures high reliability, safe handling, and easy access and service. Power transmission is via a rigid split coupling. Pipe connection is via combined DIN-ANSI-JIS flanges. The pump is fitted with a 3-phase, fan-cooled, permanent-magnet, synchronous motor. The motor efficiency is classified as IE5 in accordance with IEC 60034-30-2. The motor includes a frequency converter and PI controller in the motor terminal box. This enables continuously variable control of the motor speed, which again enables adaptation of the performance to a given requirement. An operating panel on the motor terminal box enables setting of required setpoint as well as setting of pump to "Min." or "Max." operation or to "Stop". The Grundfos Eye indicator on the operating panel provides visual indication of pump status: "Power on": Motor is running (rotating green indicator lights) or not running (permanently green indicator lights) "Warning": Motor is still running (rotating yellow indicator lights) or has stopped (permanently yellow indicator lights) "Alarm": Motor has stopped (flashing red indicator lights). Communication with the pump is possible by means of Grundfos GO Remote (accessory). The remote control enables further settings as well as reading out of a number of parameters such as "Actual value", "Speed", "Power input" and total "Power consumption". The terminal box has a number of inputs and outputs enabling the motor to be used in advanced applications where many inputs and outputs are required: two dedicated digital inputs three analog inputs, 0(4)-20 ma, 0-5 V, 0-10 V, 0.5-3.5 V 5 V voltage supply to potentiometer and sensor one analog output, 0-10 V, 0(4)-20 ma two configurable digital inputs or open-collector outputs two Pt100/Pt1000 inputs LiqTec, dry-running protection sensor input Grundfos Digital Sensor input and output 24 V voltage supply for sensors two signal-relay outputs (potential-free contacts) GENIbus connection interface for Grundfos CIM fieldbus module. Further product details An external sensor can be connected if controlled pump operation based on for example flow, differential pressure or temperature is required. An operating panel on the motor terminal box enables setting of required setpoint as well as setting of pump to "Min." or "Max." operation or to "Stop". The Grundfos Eye indicator on the operating panel provides visual indication of pump status: "Power on": Motor is running (rotating green indicator lights) or not running (permanently green indicator lights) "Warning": Motor is still running (rotating yellow indicator lights) or has stopped (permanently yellow indicator lights) "Alarm": Motor has stopped (flashing red indicator lights). Communication with the pump is possible by means of Grundfos GO Remote (accessory). The remote control enables further settings as well as reading out of a number of parameters such as "Actual value", "Speed", "Power input" and total "Power consumption". 1/15
Position Qty. Description Steel, cast iron and aluminium components have an epoxy-based coating made in a cathodic electro-deposition (CED) process. CED is a high-quality dip-painting process where an electrical field around the products ensures deposition of paint particles as a thin, well-controlled layer on the surface. An integral part of the process is a pretreatment. The entire process consists of these elements: 1) Alkaline-based cleaning. 2) Zinc phosphating. 3) Cathodic electro-deposition. 4) Curing to a dry film thickness 18-22 my m. The colour code for the finished product is NCS 9000/RAL 9005. Pump A standard split coupling connects the pump and motor shaft. It is enclosed in the pump head/motor stool by means of two coupling guards. The pump head and flange for motor mounting is made in one piece (cast iron). The pump head cover is a separate component (stainless steel). The pump head has a combined 1/2" priming plug and vent screw. The pump is fitted with a balanced O-ring seal unit with a rigid torque-transmission system. This seal type is assembled in a cartridge unit which makes replacement safe and easy. Due to the balancing, this seal type is suitable for high-pressure applications. The cartridge construction also protects the pump shaft from possible wear from a dynamic O-ring between pump shaft and shaft seal. Primary seal: Rotating seal ring material: silicon carbide (SiC) Stationary seat material: silicon carbide (SiC) This material pairing is used where higher corrosion resistance is required. The high hardness of this material pairing offers good resistance against abrasive particles. Secondary seal material: EPDM (ethylene-propylene rubber) EPDM has excellent resistance to hot water. EPDM is not suitable for mineral oils. The shaft seal is screwed into the pump head. The chambers and impellers are made of stainless-steel sheet. The chambers are provided with a PTFE neck ring offering improved sealing and high efficiency. The impellers have smooth surfaces, and the shape of the blades ensure a high efficiency. The pump has a stainless steel base mounted on a separate base plate. This base and base plate are kept in position by the tension of the staybolts which hold the pump together. The outlet side of the base has a combined drain plug and bypass valve. The pump is secured to the foundation by four bolts through the base plate. The flanges and base are cast in one piece and prepared for connection by means of DIN, ANSI or JIS. 2/15
Position Qty. Description Motor The motor is a totally enclosed, fan-cooled motor with principal dimensions to IEC and DIN standards. The motor is flange-mounted with tapped-hole flange (FT). Motor-mounting designation in accordance with IEC 60034-7: IM B 14 (Code I) / IM 3601 (Code II). Electrical tolerances comply with IEC 60034. The motor efficiency is classified as IE5 in accordance with IEC 60034-30-2. The motor requires no external motor protection. The motor control unit incorporates protection against slow- and quick-rising temperatures, e.g. constant overload and stalled conditions. The terminal box has a number of inputs and outputs enabling the motor to be used in advanced applications where many inputs and outputs are required: two dedicated digital inputs three analog inputs, 0(4)-20 ma, 0-5 V, 0-10 V, 0.5-3.5 V 5 V voltage supply to potentiometer and sensor one analog output, 0-10 V, 0(4)-20 ma two configurable digital inputs or open-collector outputs two Pt100/Pt1000 inputs LiqTec, dry-running protection sensor input Grundfos Digital Sensor input and output 24 V voltage supply for sensors two signal-relay outputs (potential-free contacts) GENIbus connection interface for Grundfos CIM fieldbus module. Technical data Controls: Frequency converter: Pressure sensor: Built-in N Liquid: Pumped liquid: Water Liquid temperature range: -20.. 120 C Liquid temperature during operation: 20 C Density: 998.2 kg/m³ Technical: Rated flow: Rated head: Pump orientation: Shaft seal arrangement: Code for shaft seal: Approvals on nameplate: Curve tolerance: Materials: Base: Impeller: Bearing: 12.1 m³/h 34.9 m Vertical Single HQQE CE, EAC,ACS ISO9906:2012 3B Stainless steel EN 1.4408 AISI 316 Stainless steel EN 1.4301 AISI 304 SIC Installation: Maximum ambient temperature: 50 C Maximum operating pressure: 16 bar Max pressure at stated temp: 16 bar / 120 C 16 bar / -20 C Type of connection: DIN / ANSI / JIS Size of inlet connection: DN 40 1 1/2 inch Size of outlet connection: DN 40 1 1/2 inch Pressure rating for pipe connection: PN 25 Flange rating inlet: 300 lb 3/15
Position Qty. Description Flange size for motor: FT115 Electrical data: Motor standard: IEC Motor type: 90LD IE Efficiency class: IE5 Rated power - P2: 2.2 kw Power (P2) required by pump: 2.2 kw Mains frequency: 50 Hz Rated voltage: 3 x 380-500 V Rated current: 4.15-3.40 A Cos phi - power factor: 0.93-0.87 Rated speed: 360-4000 rpm Efficiency: 90.1% Motor efficiency at full load: 90.1 % Enclosure class (IEC 34-5): IP55 Insulation class (IEC 85): F Others: Minimum efficiency index, MEI : 0.70 Net weight: 44 kg Gross weight: 48 kg Shipping volume: 0.143 m³ 4/15
On request CRIE 10-3 A-FGJ-A-E-HQQE 50 Hz H [m] CRIE 10-3, 3*400 V eta [%] 45 100 % 40 35 90 % 30 80 % 25 100 70 % 20 80 15 60 % 60 10 40 % 50 % 40 5 20 21 % 0 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 P [kw] Q [m³/h] 0 NPSH [m] 2.0 20 P1 (motor+freq.converter) P2 1.5 15 1.0 10 0.5 5 0.0 0 5/15
105 x13 4 130 42 1 X G 1/2 x23.5 18.5 4 G 1/2 158 122 200 280 215 248 135 Description Value General information: Product name: CRIE 10-3 A-FGJ-A-E-HQQE Product No: On request EAN number: On request Technical: Rated flow: 12.1 m³/h Rated head: 34.9 m Stages: 3 Impellers: 3 H [m] 45 40 35 30 100 % 90 % 80 % CRIE 10-3, 3*400 V eta [%] Number of reduced-diameter impellers: Low NPSH: Pump orientation: Shaft seal arrangement: Code for shaft seal: Approvals on nameplate: Curve tolerance: Pump version: Model: Materials: Base: Impeller: 0 N Vertical Single HQQE CE, EAC,ACS ISO9906:2012 3B A A Stainless steel EN 1.4408 AISI 316 Stainless steel EN 1.4301 AISI 304 A E SIC Material code: Code for rubber: Bearing: Installation: Maximum ambient temperature: 50 C Maximum operating pressure: 16 bar Max pressure at stated temp: 16 bar / 120 C 16 bar / -20 C Type of connection: DIN / ANSI / JIS Size of inlet connection: DN 40 1 1/2 inch Size of outlet connection: DN 40 1 1/2 inch 25 20 15 10 5 21 % 70 % 60 % 50 % 40 % 0 0 2 4 6 8 10 12 14 Q [m³/h] P [kw] 2.0 1.5 1.0 0.5 0.0 274 135 158 122 G 1/2 G 1/2 100 80 60 40 20 0 15 10 5 0 NPSH [m] 20 P1 (motor+freq.converter) P2 Pressure rating for pipe connection: PN 25 4 x 18.5 x 23.5 Flange rating inlet: 300 lb Flange size for motor: FT115 Connect code: FGJ Liquid: Pumped liquid: Water Liquid temperature range: -20.. 120 C 403 80 1 X G 1/2 26 130 42 200 105 280 215 248 115 150 4 x 13 Liquid temperature during 20 C operation: Density: 998.2 kg/m³ Electrical data: Motor standard: IEC Motor type: 90LD IE Efficiency class: IE5 Rated power - P2: 2.2 kw Power (P2) required by pump: 2.2 kw Mains frequency: 50 Hz Rated voltage: 3 x 380-500 V Rated current: 4.15-3.40 A Cos phi - power factor: 0.93-0.87 Rated speed: 360-4000 rpm Efficiency: 90.1% Motor efficiency at full load: 90.1 % Enclosure class (IEC 34-5): IP55 Insulation class (IEC 85): F L1 L2 L3 PE +24 V* +24 V* +24 V* +24 V* +24 V* OC DI +24 V* +24 V*/5 V* OC DI GND +24 V*/5 V* +24 V* +24 V* +24 V*/5 V* +5 V* +5 V* NC C1 NO NC C2 NO 18 11 19 17 12 9 14 1 21 20 22 10 4 2 5 6 A Y B 3 15 8 26 23 25 24 7 L1 L2 L3 GND DI4/OC2 Pt100/1000 Pt100/1000 AO GND AI3 DI2 LiqTec GND LiqTec DI3/OC1 AI1 DI1 +5 V GND GENIbus A GENIbus Y GENIbus B GND +24 V +24 V +5 V GND GDS TX GDS RX AI2 6/15
Description Value Motor protec: YES Motor No: 98190193 Controls: Control panel: Standard Function Module: FM300 - Advanced Frequency converter: Built-in Pressure sensor: N Others: Minimum efficiency index, MEI : 0.70 Net weight: 44 kg Gross weight: 48 kg Shipping volume: 0.143 m³ 7/15
On request CRIE 10-3 A-FGJ-A-E-HQQE 50 Hz cos phi eta CRIE10-3 + 90LD 2.2 kw 3*400 V, 50 Hz I [A] cos phi eta 0.8 4.0 I 0.6 3.0 0.4 2.0 0.2 1.0 0.0 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 1.1 1.2 1.3 1.4 1.5 1.6 1.7 1.8 1.9 2.0 2.1 n [rpm] P2 [kw] 0.0 P1 [kw] n 3000 3.0 P1 (motor+freq.converter) 2000 2.0 1000 1.0 0 n = 100 % 0.0 8/15
On request CRIE 10-3 A-FGJ-A-E-HQQE 50 Hz 135 G 1/2 G 1/2 4 x 18.5 x 23.5 1 X G 1/2 130 42 200 105 280 215 248 4 x 13 80 403 274 26 115 150 158 122 Note! All units are in [mm] unless others are stated. Disclaimer: This simplified dimensional drawing does not show all details. 9/15
Exploded view 251a 251d 77 28 7 7a 17 301a 219 92 301a 11 9 92 51 11b 105 100 215a 215 66a 67 49 45 18 530a 530 215a 217 531a 534 531 534a 6 10/15
Sectional drawing (TM058200 for TPE2,TPE3) 5 4 3 2 1 TM058200 11/15
Exploded view ( TM057026 for MGE model H/I ) 251d 251b 291 290 293 287 287a 502 277a 273b 277 252a 286 273a 273 275a 266 268 268a 289a 289 251a 288b 288 288a 252b 159e 157 158 150 156c 156 151 152 172 154 185 178 156d 187 153 188 191 156c 156b 192 159d 12/15
Parts list CRIE 10-3, Product No. On request Valid from 25.12.2012 (1252) Pos Description Annotation Données de classification Référence Quantité Unité - Motor 1 pcs Terminal 3 Pan head thread forming screw 4 150 Stator housing 1 150 Stator 1 151 Fan cover 1 152 Pan head thread forming screw 6 152 Pan head thread forming screw 1 152 Pan head thread forming screw 4 152 Pan head thread forming screw 1 153 Ball bearing 1 154 Ball bearing Designation: 6204.2Z.C3.SYN 1 156 Fan 1 156b Flange 1 156d Gasket Internal diameter: 114,80 1 Outer diameter: 121,20 Thickness: 0,25 157 O-ring Diameter: 47 1 Material type: NBR Thickness: 3 158 Waved washer 1 159a Seal ring 1 159c Seal ring 1 166 Torx Screw 2 172 Shaft w/rotor 1 173a Base 1 185 Cross recess Pan head screw 4 186 Drain plug 1 187 Retaining ring 1 188 Retaining ring 1 203 Terminal plug 1 251a Control box 1 251b Control box 1 251d Pan head thread forming screw 4 266 Connector plug 3-pole 1 266 Connector plug 3-pole 1 266 Connector plug 3-pole 1 266 Connector plug 8-pole 1 266 Connector plug 8-pole 1 266 Connector plug 8-pole 1 266 Connector plug 10-pole 1 268 Pan head screw 1 273 Funct. Module cpl. 1 273b Battery 1 275a Pin 1 277 Isolation cover 1 277a Cross recess Pan head screw 1 277a Cross recess Pan head screw 1 277a Cross recess Pan head screw 4 286 Spacer 1 286 Spacer 1 287 Cover 1 288 Wire clamp 3 288b Washer 6 289 Wire clamp 1 290 Control panel, cpl. 1 300 Plug cpl. 4 301 Jumper 1 - Base cpl. 1 pcs 13/15
Pos Description Annotation Données de classification Référence Quantité Unité 6 Base 1 25 Drain plug 1 56 Base plate 1 201 Flange 2 203 Helical compression spring 2 - Rubber module 1 pcs 20 Spring 4 37 O-ring 2 38 O-ring Diameter: 16,3 1 Material type: EPDM Thickness: 2,4 38a O-ring Diameter: 5,3 1 Material type: EPDM Thickness: 2,4 100 O-ring Diameter: 16,3 2 Material type: EPDM Thickness: 2,4-2 Pump head cpl. 1 pcs 2 Pump head 1 7 Coupling guard 2 7.a Combi Slot Torx screw 4-18 Air vent screw 1 Plug 1 Spindle 1 23 Plug 1 28 Hex head screw Length (mm): 20 4 Thread: M8 37.a O-ring 1 76 Nameplate 1 76a Rivet 2 77 Pump cover 1-8 Coupling cpl. 1 pcs 9 Hex socket head cap screw Designation: DIN 912 4 Length (mm): 25 Thread: M8 10 Shaft pin Diameter: 5 1 Length (mm): 26 10a Coupling half 2 26 Staybolt 4 pcs 36 Hex nut Thread: M16 4 pcs 55 Outer sleeve 1 pcs 66a Washer Designation: DIN 125 A 4 pcs Internal diameter: 17 Outer diameter: 30 Thickness: 3-80 Chamber stack Bearing type: SIC 1 pcs - 4 Intermediate chamber cpl. 1 Guide vane 10 3 Top intermediate chamber 1-4 Intermediate chamber cpl. 1 Guide vane 10 Guide cup 1 3a Intermediate chamber 1 45 Neck ring cpl. 1 65 Retainer 1-4a Intermediate chamber cpl. 1 Guide vane 10 Bearing plate 1 Bearing bush 1 Guide cup 1 3a Intermediate chamber 1 45 Neck ring cpl. 1 65 Retainer 1 26.b Hex head screw 2 14/15
Pos Description Annotation Données de classification Référence Quantité Unité 26.c Washer Designation: DIN 125A 2 Thickness: 1,6 26a Strap cpl. 2 36 Lock nut Thread: M8 1-44a Inlet part cpl. 1 Inlet part 1 Guide cup 1 45 Neck ring cpl. 1 65 Retainer 1 44b Inlet part 1 47a Bearing ring 1 49 Impeller cpl. 3-51 Shaft, spline, cpl. 1 Bar 0 62 Stop ring 1 64 Spacing bush Length (mm): 9.00 1 64.d Spacer 1 64c Spacing pipe Length (mm): 12.7 1 66 Wedge lock washer 1 69 Spacing pipe Length (mm): 29.05 1 69 Spacing bush Length (mm): 18.00 1 105 Shaft seal Material type: HQQE 1 pcs 15/15
Disclaimer: The information about the Grundfos pump in this document may be outdated. Data may be subject to alterations without further notice. Please contact us to verify the data above is still accurate/up-to-date. All information is copyright Grundfos. info@lenntech.com https://www.lenntech.com tel. +31 152 610 900 fax. +31 152 616 289