Replacement Parts List No. 700024800 Revision N 10/2018 Daikin Daikin McQuay SmartSource Single Stage Horizontal Water Source Heat Pump WGSH 015, 019 Design 1 To find your Daikin Applied parts distributor, call 1-800-377-2787 or visit www.daikinapplied.com
Contents Parts List Revision History... 3-4 Nomenclature Serial Number... 5 Model Number... 5-7 Electrical Legend... 8 Unit Sections... 9 Return Air Configurations... 9 Blower Fan Assembly... 10 Refrigeration Circuit Diagrams...11 Components... 12-13 Hot Gas Reheat... 14 Water Flow Regulator... 14 Control Box- Microtech III Controls Diagrams... 15 Components... 16 MTIII Control Board Label Location... 17 Field Installed Accessories... 18-22 Critical Parts List... CPL1 WSHP; WGSH1 015, 019 Design 1 Rev. N 10/18 RPL 7000248 / Page 2
Parts List Revision History Rev. Date Description NEW 8/12 NEW A 10/12 Page 4- Add Code 13 Sound Packages A= Premium. Page 5- Code 23 add P= Controls for Electric Heat single 24V signal(field installed Duct Heater by Others) Page 10- Add Sound Blanket p/ns 669280501 & 669280601. Page 10- Change condensate pan p/ns to SERVSub p/ns. Change condensate pan p/ns to SERVSub p/ns. Delete all base pans. Page 12- Delete Series 2 from p/n 250806500 & 250806601 descriptions. Page 17- Add Electric Duct Heater Kit. CPL1- Delete Series 2 from p/n 250806500 & 250806601 descriptions. B 12/12 Page 10- Remove Sound Blanket p/ns 669280501 and 669280601. C 2/13 Page 11- Change Condenser to CO-AX Condenser and Cupro-Nickel to Copper. Change CO-AX Coil p/n 667718401 to 910135332. D 2/13 Page 12- Change MTIII control board p/n 668105601 to 250806500. Change I/O expansion board assy p/n 668105702 to 250806601. Change LonWorks com card p/n 668105801 to 250806801. Change BACnet com card p/n 668105901 to 250806701. Remove footnote. CPL1- Change MTIII control board p/n 668105601 to 250806500; I/O exp. board p/n 668105702 to 250806601; LonWorks card p/n 668105801 to 250806801 and BACnet card p/n 668105901 to 250806701. E 3/13 Page 9- Add 460V table for ECM motors. Change ECM motors from phantom p/ns to Program p/ns. Page 13- Remove Wire Harness Assy p/n 910107989 from MTIII module kits. Page 14- Add Actuator p/n 107179809 to 3-Way Valves rename Waterside Economizer. Rename 2-Way Valves to Motorized Valves. Page 15- Remove Boilerless System Kits and move sensors to Thermostats & Sensors. CPL1- Add 460V to ECM motors. F 10/13 Rebrand Daikin. Page 9- Add ECM motor size 015 p/n 910126505. Page 12- Add LT sensors p/n 910121230. CPL1- Add ECM motor size 015 p/n 910126505. Change Reversing Valve. Add LT sensor. G 2/14 Page 12- Change H6 Connector p/n EGA9164 to 668916304. H 10/14 Numerous drawing & p/n changes done. Separate vertical & horizontal units. Pages 4-6 Change to horizontal model configeration. Code changes to C03, C10, C43 & C44. Page 8- Delete Typical Refrigeration Cycle and add Unit Sections and Return Air Configerations. Page 9- Delete 460V ECM not used in size 015-019. Ref #370 Change Qty from 1 to 3. Page 11- Change overload protector p/n 668015811 to 668015812. Change adapter p/n 106474901 to 106475001. Change fusible plug assy p/n 850001662 to 669954002. Page 12- Add Hot Gas Reheat and Water Flow Control. Page 14- Delete the control box BACnet & LonWorks p/ns 250806701 & 250806801. Page 15- Add footnote for field conversion kits LonWorks p/n910128888 & BACnet p/n 910128889. Pages 16- Add Loop Pumps. Numerous hoses were added. CPL1- Delete BACnet & LonWorks p/ns 250806701 & 250806801. Delete 460V ECM. I 4/15 Page 9- Delete ECM p/ns and add nameplate diagram and footnote1. Page 14- Delete control board p/n and add footnte *. Change Ref# 315 Change I/O Exp Board p/n 250806601 to 250806601. CPL1- Delete control board and ECM p/ns. J 11/15 Rebrand Daikin. Page 14- Ref# 229 Add MTIII p/n 668105601. Change Exp. Board p/n 250806602 to 668105702. Delete Disc. Switchs p/ns 91015059, 91015060, 910118577 & 910123457. Add handle p/n 910150957. Add Relay p/n 106500102. Delete Contactor p/n 910140340. Add footnote for MTIII Controls Label Location. Page 15- Add MTIII Controls Label Location table and footnote. CPL1- Add MTIII p/n 668105601. Delete Refrigeration Circuit. K 05/17 Page 14- Add yellow plug p/n 668302132; white plug p/n 668302122 and bridge connector p/n 910122983. L CPL1- Update revision. 06/17 Page 4- Model Number changed to table format and SLP added to Serial Number. Page 17- Add WSE Coils, RH p/ns (until 03/15) 669958104 & (03/15 & later) 669958136. Add WSE Coils, LH p/ns (until 03/15) 669958120 & (03/15 & later) 669958134. CPL1- Update revision. M 12/17 Pages 13-14 Add Ref # 240 & 238 relay p/ns 061019403 & 106500102. Page 18- Add 3 Ft. hoses. Page 19- Add boilerless system kit p/ns 910110353 & 910110355. CPL1- Update revision. Daikin Applied, 13600 Industrial Park Blvd., P.O. Box 1551, Minneapolis, MN 55440 (763) 553-5330 WSHP; WGSH1 015, 019 Design 1 Rev. N 10/18 RPL 7000248 / Page 3
Rev. Date Description N Parts List Revision History Continued 10/18 Page 4- Add Parts List Revision History page. Page 8- Electrical Legend updated. Page 12 Change Rev Valve size 015 p/n 910124938 to 910198409 and 019 p/n 106694112 to 910198412. Page 13- Add page. Change drain pan p/n 669971939 to 669972219 (LH) & 669972203 (RH). Page 16- Add footnote for disconnect switch and delete unit size. Change size for capacitor Ref# 68 & 72. Delete Connector Bridge p/n 910122983, plug p/ns 668302122 & 668302132. Pages 18-22 Numerous changes to Field Installed Accessories. Change filters from kit p/ns to single p/ns. Change WSE 3-way valve, LH p/n 910128663 to 910128662. CPL1- Update revision. WSHP; WGSH1 015, 019 Design 1 Rev. N 10/18 RPL 7000248 / Page 4
Nomenclature Serial Number AUB U 12 05 00148 Plant Identification Abbreviation AUB = Auburn SLP = San Luis Potosi U= Unit Serial Number (build sequence) Week of Manufacture Year of Manufacture 12= 2012 13= 2013 etc. Model Number WGSH 015 B 1 E WL R S 4 Y Y Y C S YYY B 2 A Y Y Y Y Code 01-03 04 05 06 07 08 09 10 11 12 13 14 15 16 17-18 19 20 21 22 23 24 25 YY B D Y Y Y YYY Y YYY S Y Y B S Y A Y A T Y C Y YY Code 26 27 28 29 30 31 32-34 35 36-38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 Y Y 2 T Y S A L K Y Y Y Y YY Y Y A Y Y Y Y A A Y Code 53 54 55 56 57 58 59 60 61 62 63 64 65 66-67 68 69 70 71 72 73 74 75 76 77 C Y Y YY FF ST ST YY YYY Y C Y Y YY 1 Code 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 Code 01: Unit Type W= Water Source Heat Pump Code 02: Model Type GS= High Efficiency, Single Stage Code 03: Configuration H= Horizontal Code 04: Unit Size 015= 15000 BtuH Nominal Cooling 019= 19000 BtuH Nominal Cooling Code 05: Unit Control B= MicroTech III Unit Controller Code 06: Design Series (Vintage) 1= Design 1 Code 07: Voltage E= 208-230/60/1 J= 265/60/1 Code 08: Range for Entering Water/Glycol Temp. WL= Water Loop GL= Ground Loop Code 09: Return Air Location L= Left-Hand Return Air & Right-Hand Piping R= Right-Hand Return Air & Right-Hand Piping Code 10: Discharge Air Location E= End S= Straight Code 11: Fan Motor 4= ECM Constant CFM Code 12: Dehumidification Option B= Hot Gas Reheat Smart Dehumidification C= Simplified Dehumidification (Lower CFM no HGRH or no Humidistat) D= Humidistat Controlled Dehumidification (No HGRH) E= Humidistat only Code 13: Sound Packages A= Premium Code 14: IAQ Packages (Indoor Air Quality) Code 15: Coaxial Heat Exchanger Construction C= Copper Inner Tube- Steel Outer Tube S= Cupro-Nickel Inner Tube- Steel Outer Tube Code 16: Primary Air Coil Options S= Standard E= E-Coated Codes 17-18: Always YYY Code 19: Communication Module B= BACnet F= BACnet - WSHP System L= LonWorks Code 20: Filter Rack 2= 4-Sided, 2" w/duct Collar & Door 3= 4-Sided, 2" w/duct Collar, Door, Hi-Merv Seal 4= 4-Sided, 4" w/duct Collar, Door, Hi-Merv Seal Continued on next page. WSHP; WGSH1 015, 019 Design 1 Rev. N 10/18 RPL 7000248 / Page 5
Nomenclature Code 21: Filter Type A= 2" Disposable E= Merv 8 (2" thick) Factory Installed G= Merv 13 (4" thick) Factory Installed Code 22: Water Coil- Indoor Air E= Waterside Economizer Code 23: Electric Heating- Indoor Air P= Controls for Electric Heat single 24V signal (Field installed Duct Heater by Others Code 24: Control Secondary Heat Type B= Boilerless Electric Heat E= Emergency Heat P= Primary Electric Heat (No Heat Pump Heating) S= Supplemental Heat Code 25: Desuperheater (Hot Water Generator) Code 26: Loop Pump Y Code 27: Coaxial Coil Supply Liquid Flow Control B= 2-Way, Motorized- 24V Valve Control, NO C= 2-Way, Motorized- 24V Valve Control, NC Code 28: Coaxial Coil Supply Liquid Auto Flow Reg D= 3.0 GPM E= 4.0 GPM G= 5.0 GPM Code 29: Coaxial Coil Supply Liquid Strianer Code 30: Always Y Code 31: Desuperheater Water Flow Options Codes 32-34: Always YYY Code 35: Water Coil Piping Package Option A= 3-Way, Motorized- 24V Valve Control, NO to Coax Codes 36-38: Always YYY Code 39: Primary Drain Pan Material S= Stainless Steel Code 40: Secondary Drain Pan Material Code 41: Compressor Insulation Code 42: Compressor Isolation B= Isolated Base Code 43: Insulation- Compressor Compartment S= Standard Insulation Package I= Indoor Air Quality (IAQ) Insulation Package R= Sound Reduction Package Code 44: Always Y Code 45: Insulation- Piping A= Insulated Piping Code 46: Always Y Code 47: Cabinet Finish A= Powder Coat G= Galvanized Steel Code 48: Cabinet Color T= Textured Charcoal Bronze W= Off White Code 49: Always Y Code 50: Fan Motor Control C= Various Speeds with 4 Adjustment Settings Code 51: Fan Motor Control location Code 52: Always YY Code 53: Disconnect Switch N= Non-Fused Code 54: Always Y Code 55: Control Transformer 1= 50VA 2= 75VA Code 56: Thermostat/Sensor Control S= Sensor Control T= Thermostat Control Code 57: Currrent Sensing Switches Code 58: Condensate Overflow Protection S= Sensor Code 59: High Pressure Switch A= 600 psi NC Code 60: Low Pressure Switch L= 7 psi NC Code 61: Low Temp. Protection Compressor Suction K= Thermistor 10K Code 62: Discharge Air Thermistor K= Thermistor 10K Code 63: Leaving Supply Fluid Temp K= Thermistor 10K Code 64: Entering Supply Fluid Temp K= Thermistor 10K Continued on next page. WSHP; WGSH1 015, 019 Design 1 Rev. N 10/18 RPL 7000248 / Page 6
Nomenclature Code 65: Return Air Thermistor K= Thermistor 10K Code 66-67: Always YY Code 68: Terminal Block Connection Code 69: Emergency Switch for Electric Heat Code 70: Annunciator A= Annunciator Code 71: Reset Button Code 72: Monitoring Code 73: Emergency Stop Code 74: External Binary Output 1 Code 75: Expansion Device A= Thermal Exp. Valve Thermal Bulb & Equalizer Tube Code 76: Alarm Relay A= Alarm Relay (Dry Contacts) Code 77: Dirty Filter Sensor Code 78: Reversing Valve C= Normally Open in Cooling Mode Code 79: Outside Air Control Code 80: Always Y Code 81: Boilerless Electric Heat Setpoint GL= Glycol 28F WA= Water 55F Y Code 82: Freeze Fault Protection FF= Freeze Fault Protection Y Code 83: Occupied Setpoint Differential (1-5F) ST= Setpoint (1 F) Code 84: Unoccupied Setpoint Differential (2-10F) ST= Setpoint (2 F) Code 85: Hydronic Heating on Setpoint (70-90F) Y Code 86: BACnet Address YY Code 87: Always Y Code 88: Agency C= ETL, CETL, ARI Code 89: Conformance Code 90: Always Y Code 91: Extended Warranty Code 92: Product Style (always 1) WSHP; WGSH1 015, 019 Design 1 Rev. N 10/18 RPL 7000248 / Page 7
Electrical Legend Sch. Sym. AN1,2 CO1-04 Description LED Annunciator Fan Motor Capacitor C11-12 Capacitor, Compressor CP1,2 Compressor 1, 2 COE COS DAT DCS Condensate Overflow Sensor - WSE Condensate Overflow Sensor Discharge Air Temp Sensor Disconnect Switch EB1 Expansion Control Board 1 EB2 EWT FM HG HP LAT LP Exp. Control Board 2- Fan Spd CTRL Entering Water Temp Sensor Fan Motor Hot Gas Reheat Valve Actuator High Pressure Switch Leaving Air Temperature Sensor Low Pressure Switch LT1,2 Suction Line Temp Sensor 1,2 Sch. Sym. LWT M01 M11 MCB NCB OLP PL R15 R20 R25 RAT RV TR1 TR2 TR3 WSE Description Leaving Water Temp Sensor Contactor, Fan Motor Contactor, Compressor Main Control Board Network Control Board Overload Protector - Compr. Motor Loop Pump Relay, Alarm Output Relay, Loop Pump Relay, Hot Gas Reheat Return Air Temp Sensor Reversing Valve Transformer - Control Transformer - Fan Motor Transformer- Loop Pump Waterside Economizer Actuator WSHP; WGSH1 015, 019 Design 1 Rev. N 10/18 RPL 7000248 / Page 8
Unit Sections Front View Side View Blower Fan Assy Refrigeration Circuit Control Box Return Air Configurations Left-hand return with end discharge Left-hand return with straight discharge Right-hand return with end discharge Right-hand return with straight discharge WSHP; WGSH1 015, 019 Design 1 Rev. N 10/18 RPL 7000248 / Page 9
Blower Fan Assembly 365 370 400 ECM Motor Detail 350 NP WARNING LABEL ECM Motor Nameplate Ref. No. Part Description Part Number Unit Size 015 019 350 Blower Housing & Wheel Assy 667838701 1 1 365 Band, Motor Mount 802009140 1 1 370 Arm, Motor Mount 668405401 3 3 400 ECM & Program 1 See ECM motor nameplate. 1 The PN for the ECM motor is found on the label (see illustration above). You may also contact Daikin Applied Parts Identification with the Unit Model & Serial Number to get the ECM Motor part number. WSHP; WGSH1 015, 019 Design 1 Rev. N 10/18 RPL 7000248 / Page 10
Refrigeration Circuit Diagrams 100 180 71 74 Evaporator/TXV Detail Condenser Detail 205 750 66 67 69 Compressor 68 65 70 60 Reversing Valve Piping 61 137 TXV Bulb Water Temp Sensor 62 See Coremax Valve Assy Detail 160 136 Compressor Mount Detail 151A 151B 151C 105 Coremax Valve Assy Detail WSHP; WGSH1 015, 019 Design 1 Rev. N 10/18 RPL 7000248 / Page 11
Refrigeration Circuit Components Ref. No. Description Part Number 015 019 N/S Grommet, Compressor Mount 802003334 4 4 N/S Hex Flange Nut, Compressor Mount 802012035 5 5 N/S Sleeve, Compressor Mount WB1044 4 4 60 Acorn Nut, Compressor Mount 910172114 3 3 61 Spacer, Compressor Mount 910172112 3 3 62 Grommet, Compressor Mount 668955401 3 3 63 Isolation Plate, Compressor Mount 668120501 1 1 65 Gasket, Compressor Mount 668382901 1 1 66 Washer, Compressor Mount 668382701 1 1 67 Nut, Compressor Mount 668383001 1 1 68 Terminal Cover, Compressor Mount 668382801 1 1 69 70 71 Compressor, 208/230V 668951601 1 Compressor, 208/230V 669660602 1 Compressor, 265V 668951603 1 1 Overload Protector, Compr 208/230V 668015808 1 Overload Protector, Compr 208/230V 668015812 1 Overload Protector, Compr 265V 668015810 1 1 COAX Coil Condenser, Copper Inner Tube 910135332 1 1 COAX Coil Condenser, CUNI Inner Tube 910135333 1 1 74 Adapter 106475001 2 2 100 Evaporator Coil Assy 1 1 1 105 N/S 136 137 Reversing Valve until 4/18 910124938 1 Reversing Valve 4/18 & later 910198409 1 Reversing Valve until 6/18 106694112 1 Reversing Valve 6/18 & later 910198412 1 Solenoid, Reversing Valve until 4/18 106694207 1 1 Solenoid, Reversing Valve 4/18 & later 910198415 1 1 High Pressure Switch until 3/16 910117560 1 1 High Pressure Switch 3/16 & later 910171269 1 1 Low Pressure Switch until 9/16 107225101 1 1 Low Pressure Switch 9/16 & later 910171267 1 1 151A Seat, Fitting 668188801 2 2 151B Core, Valve 668188701 2 2 151C Cap, Valve 668189501 2 2 N/S= Not Shown. 1 Please contact Daikin Applied Parts Identification for Coil Assy, E-Coat. Continued on next page. WSHP; WGSH1 015, 019 Design 1 Rev. N 10/18 RPL 7000248 / Page 12
Refrigeration Circuit Components, Continued Ref. No. 160 180 N/S Description Part Number 015 019 Fusible Plug Assy 669954002 1 1 Plug Only, 283 F 106057401 1 1 Expansion Valve, 1T 910114773 1 Expansion Valve, 1.5T 910117595 1 Drain Pan Assy, SSTL- LH 669972219 1 1 Drain Pan Assy, SSTL- RH 669972203 1 1 N/S Gasket, Vinyl, 14.5" 910105429 1 1 N/S= Not Shown. WSHP; WGSH1 015, 019 Design 1 Rev. N 10/18 RPL 7000248 / Page 13
Hot Gas Reheat (HGRH) 200 210 235 225 Ref. No. 200 Description Part Number Qty. HGRH Coil Assy, LH 1 669949328 1 HGRH Coil Assy, RH 1 669949337 1 210 Valve, Check 910115254 1 225 3-Way Reclaim Valve until 12/13 910114188 1 3-Way Reclaim Valve 12/13 & later 910149327 1 235 Actuator, Reclaim Valve 910125395 1 1 Please contact Daikin Applied Parts for E-Coat on coil assy. Water Flow Regulator 425 Ref. No. 425 Description Part Number Qty. Auto Flow Control Valve, 3/4" 3 GPM 669648913 1 Auto Flow Control Valve, 3/4" 4 GPM 669648914 1 Auto Flow Control Valve, 3/4" 5 GPM 669648906 1 WSHP; WGSH1 015, 019 Design 1 Rev. N 10/18 RPL 7000248 / Page 14
Control Box MicroTech III Controls Diagrams 340 DCS 67 68 237 M11 360 315 EB1 330 EB2 229 MCB 335 240 238 AN1,AN2 320 WSHP; WGSH1 015, 019 Design 1 Rev. N 10/18 RPL 7000248 / Page 15
Ref. No. Description Control Box MicroTech III Controls Components Part Number Unit Size 015 019 67 Bracket, Capacitor 850010570 1 1 N/S Capacitor Boot 910127697 1 1 68 Capacitor, 35MFD 440VAC 910120050 1 1 229 Main Controller, MicroTech III 668105601* 1 1 315 I/O Expansion Board Assy 668105702* 1 1 320 LED Annunciator Assy 668395201 2 2 330 Fan Speed Selection Board until 4/14 668917201 1 1 Fan Speed Selection Board 4/14 & later 910143618 1 1 335 Stand Off- PC Board 802028115 5 5 337 Contactor, Compr, 2P, 30A until 12/17 910140339 1 1 Contactor, Compr, 2P, 30A 12/17 & later 910199934 1 1 N/S Relay, 1PDT 061019403 1 1 339 Relay, 2PST 106500102 1 1 340 Disconnect Switch, 10A 910150557 See footnote 1. Disconnect Switch, 16A 910150558 360 Transformer, 208/230V 50VA 910116202 1 1 Transformer, 265V 50VA 910116203 1 1 Transformer, 208/230V 75VA 910116213 1 1 Transformer, 265/460V 75VA 910116209 1 1 N/S Suction Line Temp Sensor (SLT) 910121227 1 1 N/S Air Temp Sensor (DAT, RAT) 910106325 1 1 N/S Water Temp Sensor (EWT, LWT) 910121231 1 1 N/S= Not shown. 1 The disconnect switch depends on the unit features. Use the As-Built BOM on Parts E-Commerse, or get the specs from the installed disconnect, or contact Daikin Applied Parts Identification. * When ordering this board, please provide the software part number printed on the board s label. See control board photo on next page for label location. WSHP; WGSH1 015, 019 Design 1 Rev. N 10/18 RPL 7000248 / Page 16
Control Box MicroTech III Controls MTIII Control Board Label Locations Label Label 668105702 668105901 Label Label 668105601 668105801 NOTE: When ordering the control board, please provide the software part number printed on the board s label. See above for label locations. WSHP; WGSH1 015, 019 Design 1 Rev. N 10/18 RPL 7000248 / Page 17
Field Installed Accessories Filters and Filter Rack Description Qty. 015, 019 Filter Rack, 2" 1 Kit 910144580 2" Filter, Throwaway 12-Pack 060687120 2" Filter, Pleated, MERV 8 12-Pack 910123769 4" Filter, MERV 13 6-Pack 910123770 MTIII Communication Module Kits Description Part Number BacNet Field Conversion Kit * 910128889 LonWorks Field Conversion Kit * 910128888 * Kit includes comm module card, sensors, mounting tabs, and IM. MTIII H-8 Harness Assembly Kit Description Part Number MTIII, H-8 Output Wire Harness Assembly Kit 910107989 Motorized Valves Description Kit * Actuator Body 2-Way Valve Kit, Motorized, NC, 3/4" NPT 910131354 910129596 910129297 2-Way Valve Kit, Motorized, NC, 3/4" Sweat 910131360 910129596 910129294 2-Way Valve Kit, Motorized, NO, 3/4" NPT 910128987 910129299 910129297 2-Way Valve Kit, Motorized, NO, 3/4" Sweat 910131357 910129299 910129294 * Refer to IM 1151 for installing a motorized valve kit on MicroTech III units. Manual Valves Description Qty Part Number 2 pack 106065202 Combination Shutoff/Balancing Valve with Memory Stop Ball Valve- 3/4" 10 pack 106065210 WSHP; WGSH1 015, 019 Design 1 Rev. N 10/18 RPL 7000248 / Page 18
Description 1 For use with 910121754, 910152147, 910152149, or 910121753. 2 For use with 910116771, 910116772, 910116773, and 910116774. Field Installed Accessories Continued Sensors Part Number 5.25 X 7" Adapter Plate for Sensors 910121754, 910152147, 910152149, 910121753 910193064 3.75 X 5.5" Adapter Plate for Sensors 910121754, 910152147, 910152149, 910121753 910201987 5.3 X 5.3" Adapter Plate for Sensors 910121754, 910152147, 910152149, 910121753 910201988 Remote Sensor for Thermostat 668375301, 668375401 667720401 Remote Sensor for Thermostat 910121746, 910121748 107096010 Basic Room Sensor w/nsb, Override and Status LED 910152149 Room Sensor, Digital Adj, 4-Button w/ Override, Occupancy Switch & Temp Display 910152147 Room Sensor w/cool/warm Temp Adj. & Occupancy Switch 910171464 Room Sensor, Digitally Adj, Temp & Humidity Display 910121754 Wall Sensor, Adj. Cool/Warm, Occupancy Switch 910121753 Trim Ring for Sensors 910121754, 910152147, 910152149 or 910152153 910193063 Indoor Sensor for 910121750 910129095 Outdoor Sensor for 910121750 910129096 Wall Plate for Remote TStat, Insulated 107096101 Wall Plate for Remote TStat 2 910116770 Thermostats Description Part Number Programmable Touch-Screen TStat 910121750 Wall Stat: AC/DC, ACO, 7-day Programmable, 2 Heat/2 Cool with Wall Plate 668375301 Wall Stat: AC/DC, ACO, Non- Programmable, 2 Heat/2 Cool, NSB & OR with Wall Plate 668375401 TStat Non-Programmable- 2 Heat/2 Cool, ACO & MCO 910121746 TStat Programmable- 2 Heat/2 Cool, ACO & MCO and 7-day 910121748 TStat Programmable/Non-Programmable- 2 Heat/2 Cool, ACO, Touchscreen, WIFI 910193126 TStat Programmable/Non-Programmable- 2 Heat/3 Cool, ACO, Touchscreen 910193127 TStat Programmable/Non-Programmable- 2 Heat/2 Cool, ACO, Touchscreen, WIFI 910193131 TStat Programmable/Non-Programmable- 2 Heat/3 Cool, ACO, Touchscreen 910193132 TStat Guards Description Qty Part Number TStat Guard Each 105571101 TStat Guard 10- Pack 105571110 WSHP; WGSH1 015, 019 Design 1 Rev. N 10/18 RPL 7000248 / Page 19
Description Field Installed Accessories Continued Loop Pump Modules Part Number Hose Kit, 1.0" x 12 ft. Hose, 1/2" Fittings 910144772 Hose Kit, 1.0" x 12 ft. Hose, 3/4" Fittings 910144773 Hose Kit, 1.0" x 12 ft. Hose, 1.0" Fittings 910144774 Hose Kit, 1.0" x 12 ft. Hose, No Fittings 910144775 Single Pump, Geothermal Loop- Cast Iron 910127001 Single Pump, Geothermal Loop- Bronze 910127002 Dual Pump, Geothermal Loop- Cast Iron 910127003 Dual Pump, Geothermal Loop- Bronze 910127004 Relay Pump Kit 910125573 Waterside Economizer Description RH LH 3-Way Valve, Motorized, 3/4" Sweat 910128662 910128662 Actuator Motor, NC, 24V 107179809 107179809 WSE Coil Assy until 03/15 669958104 669958120 WSE Coil Assy 03/15 & later 669958136 669958134 Unit Hanger Description Part Number Unit Hanger Kit 1 669997601 1 Kit includes four (4) brackets (p/n 060609202), four (4) grommets (p/n 802003334), and hardware. WSHP; WGSH1 015, 019 Design 1 Rev. N 10/18 RPL 7000248 / Page 20
Field Installed Accessories Continued Hoses Description Specification 2 Foot 3 Foot Hose Kit, Fire Rated Condensate 3/4 106063801 106063901 Hose Kit, Plastic Condensate 3/4 106063701 106665101 Hose Kit, Fire Rated Supply/Return (2 Pack) 3/4 106062901 106063201 Auto Flow Supply and Return w/ball Valves Flow Control Hose Kit, Fire Rated Supply/Return- 3/4" Includes: Supply Line: Ball valve with one port and a 24" stainless steel hose with swivel. Return Line: Combination flow controller & ball valve with two ports and a 24" stainless steel hose with swivel. Auto Flow Supply and Return w/ball Valves and Strainer Flow Control Hose Kit, Fire Rated Supply/Return- 3/4" Includes: Supply Line: Combination ball valve & y-strainer, blow down valve, with one port and a 24" stainless steel hose with swivel. Return Line: Combination flow controller & ball valve with two ports and a 24" stainless steel hose with swivel. 3.0 GPM 669482401 N/A 3.5 GPM 669482402 N/A 4.0 GPM 669482403 N/A 4.5 GPM 669482404 N/A 5.0 GPM 669482405 N/A 6.0 GPM 669482407 N/A 3.0 GPM 106582913 910157027 3.5 GPM 106582914 910186316 4.0 GPM 106582915 910157028 4.5 GPM 106582916 910186317 5.0 GPM 106582917 910182844 6.0 GPM 106582919 910157029 Hose Kit Supply and Return w/ball Valves 3/4 669483501 669481402 Hose Kit Supply and Return w/ball Valves and Strainer 3/4 669481901 669481902 Hose Kit Jumper Hose Kit w/90 Adapter 3/4" x 4 Ft. 669483201 N/A = Not Applicable. Note: Refer to IM 1226 for Daikin Fire Rated Hoses & Hose Kits and for installation instructions. WSHP; WGSH1 015, 019 Design 1 Rev. N 10/18 RPL 7000248 / Page 21
Part Number Kit Field Installed Accessories Continued MicroTech III Temperature Sensors Tennant Override Setpoint Adjustment Status LED Note: Can only be used in conjunction with a communication (Comm.) card. See OM 931 for required jumper settings. Fan & Mode Switch 669088101 669529001 Yes No No No 668900801 669529101 Yes 55 to 95 F (12 to 35 C) Yes Yes 669088201 669529201 Yes -3 to +3 F (-1.5 to 1.5 C) No Yes Description * IM 1084-2 is included in Kit. ** Kit components listed below. Microtech III Unit Control Accessories ** Multiple Unit Control Panel: Allows a master unit controlled by a single thermostat, to operate up to 3 secondary units. Not Recommended for use with a Boilerless System Kit. Part Number 056794201 Boilerless System Kit with I/O Expansion Board * 910110355 Boilerless System Kit without I/O Expansion Board 910110353 Multiple Unit Control Panel Kit 310 311 313 Ref. Part Description Qty. No. Number 310 Cover, Control Box 106436101 1 311 Circuit Board 056794001 1 312 Stand Off, Circuit Board 802028090 6 313 Box 850007827 1 312 WSHP; WGSH1 015, 019 Design 1 Rev. N 10/18 RPL 7000248 / Page 22
Critical Daikin Applied OEM Parts Are What Your HVAC Unit Needs! Daikin SmartSource Single Stage WSHP Daikin McQuay SmartSource Single Stage WSHP WGSH 015, 019 Design 1 Critical Components Unit Sizes Voltage Part Number Control Control Board, MicroTech III ALL ALL 668105601 Compressor Compressor 015 208-230/60/1 668951601 Compressor 015 265/60/1 668951603 Compressor 019 208-230/60/1 669660602 Compressor 019 265/60/1 669660603 Blower Motor ECM & Program ALL ALL See motor nameplate Blower Fan Assembly Blower Housing & Wheel Assy ALL N/A 667838701 Sensor Line Temp Sensor (SLTS) ALL N/A 910121227 Air Temp Sensor (DAT, RAT) ALL N/A 910106325 Water Temp Sensor (EWT, LWT) ALL N/A 910121231 Call Your Local Daikin Applied Parts Distributor For All Your Parts Needs. To Locate A Distributor, Go To www.daikinapplied.com or Call 1-800-37PARTS 7000248 Rev. N 10/2018 CPL Page 1 of 1