INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS Accessory REMOTE ENGINE STARTER SYSTEM Application 2010 CIVIC 4-DOOR Publications No. AII 42460 Issue Date AUG 2009 PARTS LIST Remote Engine Starter Unit Kit P/N 08E91-E22-100B Transmitter Accessory User s Information Manual Quick Start Guide Control unit Remote Engine Starter Attachment Kit P/N 08E92-SNA-100B Engine starter harness Antenna Control unit bracket Key ring Relay bracket Protective tape Engine starter label 3 Black relays (4-pin) Fuse label 18 Wire ties 2009 American Honda Motor Co., Inc. All Rights Reserved. AII 42460 (0908) 08E92-SNA-1B01-91 1 of 21

7 Foam cushion tapes Flange nut Clip Green relay (5-pin) Template TOOLS AND SUPPLIES REQUIRED Phillips screwdriver Long blade flat-tip screwdriver Small flat-tip screwdriver 6 mm Hex wrench T25 Torx bit 3 mm and 7 mm Drill bits File Ratchet 10 mm Socket Combination wrench Isopropyl alcohol Shop towel Tape measure Clip remover Diagonal cutters Felt-tip pen Punch Scissors 2 Pairs of needle nose pliers Rubber mallet HDS (Honda Diagnostic System) Masking tape Safety goggles Scale 2 of 21 AII 42460 (0908) 2009 American Honda Motor Co., Inc. All Rights Reserved.

Illustration of the Remote Engine Starter System Installed on the Vehicle Setting the Control Unit 2 FUSES 40 A RELAY (5-PIN) ENGINE STARTER 3. Get the control unit. Using a small flat-tip screwdriver, adjust the switches on the control unit to the locations shown. Using isopropyl alcohol on a shop towel, clean the area where the protective tape will attach. Attach the protective tape to the control unit over the switches. NOTE: The switches must be selected before the control unit is plugged in. If the switch setting is not correct, the engine starter will not operate correctly. 3 RELAYS (4-PIN) 2 FUSES 3 A CONTROL UNIT 872601AT If setting the switches when the control unit is installed in the vehicle, touch a metal part of the screwdriver to a metal part of the vehicle to discharge any static electricity. If you change the switch settings with the unit connected, you must disconnect the unit, then reconnect it before the settings will change. INSTALLATION CONTROL UNIT Customer Information: The information in this installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your vehicle. These procedures should not be attempted by do-it-yourselfers. NOTE: This antenna should only be installed if the ambient air temperature 15 C (60 F) or above. 1. Make sure you have the anti-theft code for the radio, then write down the radio station presets. SMALL FLAT-TIP SCREW- DRIVER SWITCHES SWITCHES Discharge any static electricity. The switches must be selected before the control unit is plugged in. 2. Disconnect the negative cable from the battery. SET SW:1 RR Junction unit -----------------------> OFF SW:2 Trunk or Tailgate ----------------------> OFF SW:3 Smart Entry -----------------------------> OFF SW:4 Horn or Buzzer Answerback ------> OFF SW:5 Trunk Main SW -------------------------> OFF SW:6 Reserve ----------------------------------> ON 2009 American Honda Motor Co., Inc. All Rights Reserved. AII 42460 (0908) 3 of 21

Removing the Vehicle Parts 4. Remove the trunk lid/fuel fill door opener cover (six retaining tabs). Remove one self-tapping screw. SELF- TAPPING SCREW COVER 6 RETAINING TABS 6. Remove the left front door sill trim (two retaining tabs, five clips, and three hooks). 3 HOOKS KEY Unlock. 5 CLIPS 2 RETAINING TABS 5. Using the key, unlock the opener. TRUNK LID/ FUEL FILL DOOR OPENER 872602AT FRONT LEFT FRONT DOOR SILL TRIM 872603AT 7. Pull away the weatherstrip, and remove the left kick panel (two clips). WEATHERSTRIP 2 CLIPS LEFT KICK PANEL 872604AT 4 of 21 AII 42460 (0908) 2009 American Honda Motor Co., Inc. All Rights Reserved.

8. If equipped, remove the driver s dashboard under cover (turn the knob counterclockwise, and release the two clips and pin). 10. Lower the tilt lever, and pull the steering wheel toward you. Insert a long blade flat-tip screwdriver along the guide of the column lower cover, and pry the retaining tab of the column upper cover. 2 RETAINING TABS PIN Push. COLUMN UPPER COVER 2 CLIPS DRIVER S DASHBOARD UNDER COVER KNOB 2 HOOKS COLUMN LOWER COVER 872605AT 9. Remove the driver s dashboard lower cover (eight clips). TILT LEVER RETAINING TAB GUIDE LONG BLADE FLAT-TIP SCREWDRIVER 872607AT 11. Push on the column lower cover in the area shown to separate the column upper cover from the column lower cover (two retaining tabs). Pull up to remove the column upper cover (two hooks). DRIVER S DASHBOARD LOWER COVER 8 CLIPS 872606AT 2009 American Honda Motor Co., Inc. All Rights Reserved. AII 42460 (0908) 5 of 21

12. Remove the column lower cover (two self-tapping screws and one screw). 14. Remove the sunvisor holders. Using a small flat-tip screwdriver, push the hook, and turn the holder 90, then pull it out. MAP LIGHT CONSOLE COLUMN LOWER COVER SCREW SELF- TAPPING SCREW 872608AT 13. If equipped, use a small flat-tip screwdriver to remove the left and right lens from the map light console (four retaining tabs for each lens). Remove the two bolts, and then release the map light console. FRONT MAP LIGHT CONSOLE SUNVISOR HOLDER 15. Remove the cap from the left sunvisor (four retaining tabs). S (if equipped) 4 RETAINING TABS SMALL FLAT-TIP SCREWDRIVER 872610AT BOLTS 4 RETAINING TABS LENS CAP TORX SCREWS LEFT SUNVISOR 872611AT 4 RETAINING TABS LENS 872609AT 16. Remove the left sunvisor (two T25 Torx screws, and unplug the vehicle connectors, if equipped). 6 of 21 AII 42460 (0908) 2009 American Honda Motor Co., Inc. All Rights Reserved.

17. Pull away the weatherstrip from the driver s A-pillar trim. 19. Pull away the weatherstrip from the driver s A-pillar trim. Remove the trim (two clips). Strike perpendicularly to the vehicle. A-PILLAR A-PILLAR TRIM 2 CLIPS PIN CLIP A-PILLAR TRIM STRIKE POINT SHOP TOWEL WEATHERSTRIP 872613AT 20. Remove the clip from the driver s A-pillar, and install a new clip. RUBBER MALLET WEATHERSTRIP CLIP A-PILLAR TRIM NEW CLIP 872612AT 18. Using a rubber mallet and a shop towel, gently tap the driver s A-pillar trim at the position shown to release the clip. Gently tap the pillar trim just below the SIDE CURTAIN AIRBAG mark. CLIP Discard. A-PILLAR TRIM 872614AT 2009 American Honda Motor Co., Inc. All Rights Reserved. AII 42460 (0908) 7 of 21

Installing the Antenna 21. Using scissors, cut out the template. 23. Using two pairs of needle-nose pliers, bend the antenna plate according to the illustration and measurement shown. SCISSORS TEMPLATE 15 mm (0.6 in.) 8 mm (0.3 in.) Cut out. 872615AT 22. Secure the template to the windshield with the masking tape by aligning it with the edge of the black ceramic paint as shown. SCALE NEEDLE-NOSE PLIERS BLACK CERAMIC PAINT EDGE OF BLACK CERAMIC PAINT PLATE WINDSHIELD TEMPLATE MASKING TAPE Align with the end of the black ceramic paint. 872616AT 872617AT 8 of 21 AII 42460 (0908) 2009 American Honda Motor Co., Inc. All Rights Reserved.

24. Measure the antenna cable as shown. Attach the three foam cushion tapes to the antenna cable in the measurement shown. 28. Route the antenna cable under the headliner towards the driver s side of the vehicle, and down along the vehicle harness. Be careful not to crease the headliner. CABLE FOAM CUSHION TAPE HEADLINER 360 mm (14 in.) 30 mm (1.2 in.) 30 mm (1.2 in.) 872618AT 25. Using isopropyl alcohol on a shop towel, clean the area where the antenna will attach. Allow to dry before proceeding. CABLE 872620AT 29. Continue routing the antenna cable between the A-pillar and the dashboard. HEADLINER Clean. A-PILLAR TEMPLATE DASHBOARD PLATE BACKING CABLE 872619AT 872621AT 26. Remove the backing from the antenna, insert the antenna plate under the headliner, and attach the antenna to the windshield in alignment with the template. 27. Remove the template. 2009 American Honda Motor Co., Inc. All Rights Reserved. AII 42460 (0908) 9 of 21

30. Using isopropyl alcohol on a shop towel, clean the areas where the foam cushion tape will attach. Under the headliner, secure the antenna cable to the roof panel with the two foam cushion tapes (cut one foam cushion tape in half) in the areas shown. 32. Secure the antenna cable to the vehicle harness with one wire tie. Secure the wire tie between the vehicle harness branching points. WIRE TIE HEADLINER FOAM CUSHION TAPE (1/2) CABLE FOAM CUSHION TAPE 872622AT BRANCHING POINT CABLE 31. Secure the antenna cable to the vehicle harness with four wire ties as shown. Do not secure the antenna cable to the drain tube. 872624AT CLIP DRAIN TUBE 4 WIRE TIES CABLE 872623AT 10 of 21 AII 42460 (0908) 2009 American Honda Motor Co., Inc. All Rights Reserved.

Installing the Control Unit Bracket 33. Locate small square hole next to small round hole in the dashboard support bracket. Under the dash, attach the control unit bracket to the vehicle bracket near the lower A-pillar using a flange nut. If the vehicle is equipped with a moonroof, be careful not to pull on the drain tube. BRACKET FRONT Routing the Engine Starter Harness 34. Using isopropyl alcohol on a shop towel, clean the areas where the fuse labels will attach. Attach the 3A fuse labels to the engine starter harness fuse case, and the 40A fuse labels to the fuse block. LAYOUT OF RELAYS WHEN VIEWED FROM FRONT 4-PIN RELAY (black) RELAY BLOCK 5-PIN RELAY (green) CLIP 40A FUSE LABEL FUSE CASE 3A FUSE LABEL FUSE BLOCK Clean. Clean. BRACKET FLANGE NUT 4-PIN RELAY (black) CONTROL UNIT BRACKET 872626AT 872627AT 35. Install the four relays to the engine starter harness relay blocks. Be careful to install the relays properly, or a malfunction will result. 2009 American Honda Motor Co., Inc. All Rights Reserved. AII 42460 (0908) 11 of 21

36. Route the engine starter harness 7-pin connectors up the steering column and to the ignition switch. Unplug the white vehicle 7-pin connector. Plug the white engine starter harness 7-pin connectors in between the vehicle 7-pin connector. IGNITION SWITCH 38. Disconnect the vehicle 8-pin connector on the rear of the wiper switch and plug the engine starter harness 8-pin connector into the vehicle 8-pin connector. 8-PIN ENGINE STARTER 8-PIN 7-PIN (White) ENGINE STARTER 7-PIN (White) WIPER SWITCH 872630AT 39. Secure the connected 8-pin connector with one wire tie to the engine starter harness. 872628AT 37. Unplug the brown vehicle 7-pin connector, and plug the brown engine starter harness 7-pin connector into the vehicle connector. NOTICE Check that the engine starter harness 7-pin connector (brown) is connected to the vehicle connector and it is locked securely. A loose connector can cause the engine to stall. CONNECTED 8-PIN WIRE TIE ENGINE STARTER 7-PIN (Brown) ENGINE STARTER WIPER SWITCH 872631AT Pull the connector and check that it is locked securely. 7-PIN (Brown) (Not reconnected.) 872629AT 12 of 21 AII 42460 (0908) 2009 American Honda Motor Co., Inc. All Rights Reserved.

40. Wrap the vehicle 7-pin connector with one foam cushion tape, then place the vehicle 7-pin connector into the gap of the column. 7-PIN (Brown) Squeeze into this area. ENGINE STARTER GREEN TAPE 4 WIRE TIES 43. Beside the right of the steering shaft, locate the sub joint box. Using a small flat-tip screwdriver, unplug the vehicle 6-pin connector from the sub joint box. Plug the engine starter harness 6-pin connectors into the vehicle 6-pin connector and the subjoint box. VIEWED FROM UNDERSIDE 6-PIN SUB JOINT BOX FRONT FOAM CUSHION TAPE LOCK WIRE TIE 7-PIN BRACKET ENGINE STARTER 872632AT 41. Secure the engine starter harness to the vehicle harness with four wire ties in the areas shown. Note the lock of the wire ties face up. ENGINE STARTER 6-PIN 6-PIN 872634AT 44. Attach the relay blocks and fuse case on the relay bracket. 42. Remove the lower steering column support bracket bolt. Attach the relay bracket to the steering column support bracket and reinstall the steering column support bracket bolt. RELAY BRACKET WIRE TIE FUSE CASE RELAY BLOCK ENGINE STARTER 872635AT STEERING COLUMN SUPPORT BRACKET BOLT Reuse. RELAY BRACKET STEERING COLUMN SUPPORT BRACKET 872633AT 45. Secure the engine starter harness to the vehicle harness using one wire tie. 2009 American Honda Motor Co., Inc. All Rights Reserved. AII 42460 (0908) 13 of 21

Without driver s dashboard under cover, go to step 48. With driver s dashboard under cover, continue with step 46. 46. Measure the indicated dimension on the instrument panel and mark with a felt-tip pen and a punch. INSTRUMENT PANEL 48. Secure the engine starter harness to the instrument panel using a wire tie. With driver s dashboard under cover: Secure in the hole opened in the instrument panel. With Driver s dashboard under cover: Secure through the existing hole for undercover securing. WIRE TIE View from below FRONT 6 mm (0.2 in.) 12 mm (0.5 in.) FELT-TIP PEN PUNCH 872636AT 47. Drill a 3 mm hole, and then a 7 mm hole at the marked position of the instrument panel. Wear safety goggles during drilling. Using a file, remove any burrs at the edges of the holes you made. FUSE BOX CLIP WITH DRIVER S DASHBOARD UNDER COVER 872638AT 49. Use the clip on the engine starter harness to secure the engine starter harness to the fuse box. 50. Disconnect the vehicle 42-pin, 4-pin, and 2-pin connectors. INSTRUMENT PANEL 4-PIN 42-PIN 2-PIN FUSE BOX FUSE BOX FRONT VIEW DRILL BIT (3 mm, 7 mm) 2-PIN 4-PIN LOCK DRILL 872637AT 42-PIN 872639AT 14 of 21 AII 42460 (0908) 2009 American Honda Motor Co., Inc. All Rights Reserved.

51. Plug the engine starter harness 4-pin and 2-pin connectors into the fuse box. NOTICE Check that the engine starter harness 4-pin and 2-pin connectors are connected to the fuse box and they are locked securely. Loose connectors can cause engine stall. 53. Connect the engine starter harness 23-pin connectors with each other and secure them with one wire tie to the vehicle harness. ENGINE STARTER 23-PIN (blue) 4-PIN PORT 2-PIN PORT FOAM CUSHION TAPE 4-PIN WIRE TIE 2-PIN WIRE TIE 872641AT 54. Unplug the white vehicle 14-pin connector at the front lower pillar behind the fuse box, and plug the engine starter harness 14-pin connectors in between. Attach the engine starter harness 14-pin connector to the vehicle 14-pin connector. ENGINE STARTER 4-PIN ENGINE STARTER 2-PIN FUSE BOX FUSE BOX 14-PIN (White) Pull the connector and check for securely locking. 872640AT 52. Wrap foam cushion tape to the vehicle 2-pin and 4-pin connectors and secure them with one wire tie. Then, secure the vehicle harness with one wire tie. Reconnect the vehicle 42-pin connector. 14-PIN (White) ENGINE STARTER 14-PIN 872642AT 2009 American Honda Motor Co., Inc. All Rights Reserved. AII 42460 (0908) 15 of 21

55. Install the clip from the engine starter harness to the fuse box bracket behind the fuse box. GROUND BOLT Reuse. 58. Install the control unit on the control unit bracket. 59. Bundle the excess antenna cable with two wire ties and secure it with one wire tie to the vehicle harness. FRONT ENGINE STARTER GROUND TERMINAL ENGINE STARTER CLIP WIRE TIES CABLE FUSE BOX BRACKET 872645AT 872643AT 56. Remove the ground bolt from the vehicle. Secure the engine starter harness ground terminal with the ground bolt you just removed. Installing the Control Unit 57. Connect the antenna cable terminal and the engine starter harness 18-pin connector to the control unit. 60. Using isopropyl alcohol on a shop towel, clean the area where the engine starter label will attach. HOOD Clean. CABLE TERMINAL Connect first. BACKING ENGINE STARTER LABEL 872646AT CONTROL UNIT BRACKET CONTROL UNIT ENGINE STARTER 18-PIN FRONT 872644AT 61. Remove the backing from the engine starter label. Attach the engine starter label to the back of the hood. 16 of 21 AII 42460 (0908) 2009 American Honda Motor Co., Inc. All Rights Reserved.

62. Check that all wire harnesses are routed properly and all connectors are plugged in. 63. Reinstall all removed parts. Check that all clips and other fasteners are installed securely. Take care not to pinch the airbag with a clip during reinstallation of the front pillar trim. Do not push the front pillar trim excessively. 64. Reconnect the negative cable to the battery. Check that the electrical accessory and other electrical systems function properly. 65. Perform REMOTE ENGINE STARTER REGISTRATION and FUNCTION CHECK. 66. Enter the customer s radio anti-theft code, and reset the radio station presets. 67. Reset the clock. REMOTE ENGINE STARTER REGISTRATION 1. Acquire the PCM code from ISIS. 2. Connect the HDS tester to the OBD II data link connector, then turn the ignition switch to ON (II). 3. Start the HDS, and click the car icon. CAR ICON 4. Input the VIN and other required information into the HDS, then click the check button. Input the VIN and other required information. CHECK BUTTON 2009 American Honda Motor Co., Inc. All Rights Reserved. AII 42460 (0908) 17 of 21

5. Select Honda Systems, then click the check button. 7. A REMARKS message will display. Click the check button. REMARKS message Select Honda Systems. CHECK BUTTON CHECK BUTTON 6. Select the R/C ENG STARTER and click the check button. 8. Select REGISTER REMOTE CONTROL ENGINE STARTER UNIT, then click the check button. Select R/C ENG STARTER. CHECK BUTTON Select REGISTER REMOTE CONTROL ENGINE STARTER UNIT. CHECK BUTTON 18 of 21 AII 42460 (0908) 2009 American Honda Motor Co., Inc. All Rights Reserved.

9. The following message will display: Obtain PCMcode (IMMOBILIZER PCM CODE) from in. This vehicle s VIN will be required to obtain the password. (USA). Click the check button. Obtain PCM-code" message 11. The following message will display: The registration of the Remote Control Engine Starter Unit has been completed. Click the check button. "Registration" message CHECK BUTTON CHECK BUTTON 10. Input the PCM code, then click the check button. NOTE: To ensure security, the PCM code (password) is changed everyday, so it is impossible to register the remote engine starter if the date of the PCM code acquisition and registration are different. The date of the HDS tester should also be the same. 12. The following message will display: Check that the engine can be started by the Transmitter. Click the check button. Check that the engine can be started by the Transmitter Input the PCM code. CHECK BUTTON CHECK BUTTON 13. Perform the function test on the next page, then disconnect the HDS. FUNCTION CHECK 2009 American Honda Motor Co., Inc. All Rights Reserved. AII 42460 (0908) 19 of 21

Operating Conditions The hood is closed. Shift lever is in park. The key is not in the ignition switch. All doors and trunk are closed and locked. Inspection 1. Within 1 second, press the command button, and then the start button on the transmitter. The engine should start if all operating conditions are met. Does the engine start? Yes - Operation is normal. No: Make sure all operating conditions are met. Check the engine starter harness connections. Connect the HDS and check for an indicated failure. (Refer to the appropriate service manual for details.) 2. Press the command button on the transmitter, and within 1 second, press the stop button. The engine should stop. Does the engine stop? DISPLAY Yes - Operation is normal. No - Check the engine starter harness connections. 3. After the engine has stopped, start the engine again, and check that the engine stops after each of the following conditions: NOTE: After each test the ignition key must be cycled, or the driver s door must be opened and closed. Move the shift lever out of the P position. Unlock or open the doors or the trunk lid. Open the hood. Insert the key in the ignition switch. Press on the brake pedal. Does the engine stop after each of these tests? STOP BUTTON TRANSMITTER COMMAND BUTTON START BUTTON 732904AY Yes - Operation is normal. No - Check the engine starter harness connections. 4. Check that the power window or the moonroof does not function when the engine is started with the transmitter. 5. Press the command button on the transmitter twice and check the vehicle condition on the display. 6. Check the operation of the transmitter when the vehicle is 100 m to 150 m (325 to 490 ft.) away, and when the vehicle is in direct sight. 20 of 21 AII 42460 (0908) 2009 American Honda Motor Co., Inc. All Rights Reserved.

How to Program an Additional Transmitter 1. Connect the HDS to the data link connector. 2. Start the HDS and click on the car icon. 3. Input the vehicle s VIN and other required information. 4. Select Honda Systems. 5. Select R/C Engine Starter. 6. Select REGISTER NEW TRANSMITTER. 7. When Ready to program the new transmitter shows, select ENTER. 8. Press and release the Command button. 9. Press and release the Stop button. 10. Perform the function check on both transmitters. NOTE: Only two remotes can be stored in the system s memory. 2009 American Honda Motor Co., Inc. All Rights Reserved. AII 42460 (0908) 21 of 21