Alarms & Remote Start Automotive Data Solutions Inc. INSTALL GUIDE ADS-AL(DL)-HA2-EN AVAILABLE FOR : ADS-AL CA Rev. Date: May 20, 2016 Doc. No.: ##28730## U.S. PATENT NO. 8,856,780 HA2 The brand names and logos found in this guide are property of their respective owners. NOTICE: The manufacturer will accept no responsibility for any electrical damage resulting from improper installation of this product, be that either damage to the vehicle itself or to the installed device. This device must be installed by a certified technician. This guide has been written for properly trained technicians; a certain level of skill & knowledge is therefore assumed. Please!review the Installation Guide carefully before beginning any work.
Page 2 of 11 ADS-AL(DL)-HA2-EN Doc. No.: ##28730## 20160520 INSTALL TYPE SELECTION FEATURES MAKE MODEL NOTE I WARNING: This solution does NOT cover hybrid vehicles with a manual transmission. Do not, under any circumstances, attempt to install. YEAR INSTALL TYPE DATA IMMOBILIZER BYPASS ARM OEM ALARM DISARM OEM ALARM A/M ALARM CTRL FROM OEM REMOTES A/M RS CTRL FROM OEM REMOTES AUTOLIGHT CTRL* DOOR LOCK DOOR UNLOCK TRUNK/HATCH RELEASE POWER LIFTGATE DOOR STATUS OUTPUT TRUNK STATUS OUTPUT HOOD STATUS OUTPUT ACURA HONDA CSX AT/MT 06-11 3 MDX AT 07-13 2 RDX AT 07-12 3 Civic AT/MT 06-11 3 Civic Hybrid AT 06-11 3 CR-V AT/MT 07-11 3 CR-Z AT 11-16 3 Fit AT/MT 09-13 1 Insight AT 10-14 1 *This feature will unlock then lock the vehicle s doors on RS shutdown. To turn it off, deactivate the RAP shutdown. (See module navigation chart) Use traditional hardwired installation method for feature to be functional during remote start.
Page 3 of 11 ADS-AL(DL)-HA2-EN Doc. No.: ##28730## 20160520 WARNING: READ CAREFULLY IMPORTANT I II III Ground When Running from Remote Starter must be provided BEFORE Ignition. Failure to comply may result in immobilizer bypass malfunction during remote start. If Ground When Running from Remote Starter CAN T be provided BEFORE Ignition, use a separate TB-HA for immobilizer bypass ONLY. - DO NOT program unlock before start on the Remote Starter. - DO NOT change Remote Starter OEM alarm control default settings. Failure to comply may result in product malfunction.
Page 4 of 11 ADS-AL(DL)-HA2-EN Doc. No.: ##28730## 20160520 TYPE 1 - CROSS REFERENCE CHART MAKE MODEL HONDA YEAR DESCRIPTION NAME TYPE POSITION POLARITY MODULE LOCATION COMPONENT LOCATOR Fit AT/MT Insight AT 09-13 10-14 Ignition ~ Green 07 pin 02 Red (+) Ignition switch ~ Key Data ~ Green 07 pin 03 Green (DATA) Ignition switch ~ SWC ~ Green 07 pin 04 LtGreen (DATA) Ignition switch ~ Ignition ~ Green 07 pin 02 Red (+) Ignition switch ~ Key Data ~ Green 07 pin 03 LtGreen (DATA) Ignition switch ~ SWC ~ Green 07 pin 04 Green (DATA) Ignition switch ~
Page 5 of 11 ADS-AL(DL)-HA2-EN Doc. No.: ##28730## 20160520 TYPE 1 - WIRING DIAGRAM REMOTE STARTER STARTER (+) OUTPUT TRUNK (-) OUTPUT UNLOCK (-) OUTPUT LOCK (-) OUTPUT 12V (+) GROUND (-) GWR (-) OUTPUT REQUIRED -> HOOD STATUS (-) INPUT TRUNK STATUS (-) INPUT DOOR STATUS (-) INPUT LEGEND NOT REQUIRED IN (1-WAY) NOT REQUIRED IN (2-WAY) USE OR HARD MODE CONNECT TO GROUND TO ENABLE AUTOMATIC RELOCK AFTER START GWR (-) INPUT - BLUE/WHITE (NC) NO GROUND - BLACK 12V (+) - RED LOCK/ARM (-) INPUT - GREEN/BLACK UNLOCK/DISARM (-) INPUT - BLUE/BLACK TRUNK (-) INPUT - RED/WHITE (NC) BROWN (NC) PURPLE/YELLOW GROUND (-) INPUT - PURPLE/BLACK (NC) WHITE STARTER (+) INPUT - BLACK/WHITE (NC) GREEN (NC) PURPLE/WHITE WHITE/BLACK - IGNITION (+) SIDE WHITE/RED - IGNITION (+) VEHICLE SIDE WHITE (NC) YELLOW/BLACK - DOOR STATUS (-) OUTPUT YELLOW/RED - TRUNK STATUS (-) OUTPUT YELLOW - HOOD STATUS (-) OUTPUT BROWN/RED (NC) BROWN/YELLOW (NC) ORANGE/BLACK - KEY DATA ORANGE/WHITE (NC) ORANGE - SWC PINK/BLACK (NC) PINK - IGNITION (+) INPUT BLUE/RED (NC) BLUE/YELLOW (NC) GREEN/RED (NC) GREEN/YELLOW (NC) GRAY/RED (NC) GRAY/YELLOW (NC) KEY DATA SWC 1 2 3 4 5 6 7 IGNITION (+)
Page 6 of 11 ADS-AL(DL)-HA2-EN Doc. No.: ##28730## 20160520 TYPE 2 - CROSS REFERENCE CHART MAKE MODEL YEAR DESCRIPTION NAME ACURA TYPE POSITION POLARITY MODULE LOCATION COMPONENT LOCATOR MDX AT 07-13 Ignition ~ White 07 pin 02 Brown (+) At immobilizer ~ Key Data ~ White 07 pin 03 LtGreen (DATA) At immobilizer ~ SWC ~ White 07 pin 04 LtGreen (DATA) At immobilizer ~
Page 7 of 11 ADS-AL(DL)-HA2-EN Doc. No.: ##28730## 20160520 TYPE 2 - WIRING DIAGRAM REMOTE STARTER STARTER (+) OUTPUT DISARM (-) OUTPUT TRUNK (-) OUTPUT UNLOCK (-) OUTPUT LOCK (-) OUTPUT 12V (+) GROUND (-) GWR (-) OUTPUT REQUIRED -> HOOD STATUS (-) INPUT TRUNK STATUS (-) INPUT DOOR STATUS (-) INPUT LEGEND NOT REQUIRED IN (1-WAY) NOT REQUIRED IN (2-WAY) USE OR HARD MODE GWR (-) INPUT - BLUE/WHITE (NC) NO GROUND - BLACK 12V (+) - RED LOCK/ARM (-) INPUT - GREEN/BLACK UNLOCK (-) INPUT - BLUE/BLACK TRUNK (-) INPUT - RED/WHITE DISARM (-) INPUT - BROWN (NC) PURPLE/YELLOW (NC) PURPLE/BLACK (NC) WHITE STARTER (+) INPUT - BLACK/WHITE (NC) GREEN (NC) PURPLE/WHITE WHITE/BLACK - IGNITION (+) SIDE WHITE/RED - IGNITION (+) VEHICLE SIDE WHITE (NC) YELLOW/BLACK - DOOR STATUS (-) OUTPUT YELLOW/RED - TRUNK STATUS (-) OUTPUT YELLOW - HOOD STATUS (-) OUTPUT BROWN/RED (NC) BROWN/YELLOW (NC) ORANGE/BLACK - KEY DATA ORANGE/WHITE (NC) ORANGE - SWC PINK/BLACK (NC) PINK - IGNITION (+) INPUT BLUE/RED (NC) BLUE/YELLOW (NC) GREEN/RED (NC) GREEN/YELLOW (NC) GRAY/RED (NC) GRAY/YELLOW (NC) KEY DATA SWC 1 2 3 4 5 6 7 IGNITION (+)
Page 8 of 11 ADS-AL(DL)-HA2-EN Doc. No.: ##28730## 20160520 TYPE 3 - CROSS REFERENCE CHART MAKE MODEL YEAR DESCRIPTION NAME ACURA TYPE POSITION HONDA POLARITY MODULE LOCATION COMPONENT LOCATOR RDX AT CSX AT/MT Civic AT/MT Civic Hybrid AT CR-V AT/MT CR-Z AT 07-12 06-11 06-11 06-11 07-11 11-16 Ignition ~ White 07 pin 02 Yellow (+) Ignition switch ~ Key Data ~ White 07 pin 03 LtGreen (DATA) Ignition switch ~ SWC ~ White 07 pin 04 Pink (DATA) Ignition switch ~ Ignition ~ White 07 pin 02 Yellow (+) Ignition switch ~ Key Data ~ White 07 pin 03 LtGreen (DATA) Ignition switch ~ SWC ~ White 07 pin 04 Pink (DATA) Ignition switch ~ Ignition ~ White 07 pin 02 Yellow (+) Ignition switch ~ Key Data ~ White 07 pin 03 LtGreen (DATA) Ignition switch ~ SWC ~ White 07 pin 04 Pink (DATA) Ignition switch ~ Ignition ~ White 07 pin 02 Yellow (+) Ignition switch ~ Key Data ~ White 07 pin 03 LtGreen (DATA) Ignition switch ~ SWC ~ White 07 pin 04 Pink (DATA) Ignition switch ~ Ignition ~ White 07 pin 02 LtBlue (+) Ignition switch ~ Key Data ~ White 07 pin 03 Green (DATA) Ignition switch ~ SWC ~ White 07 pin 04 Pink (DATA) Ignition switch ~ Ignition ~ White 07 pin 02 Yellow (+) Ignition switch ~ Key Data ~ White 07 pin 03 Pink (DATA) Ignition switch ~ SWC ~ White 07 pin 04 Green (DATA) Ignition switch ~
Page 9 of 11 ADS-AL(DL)-HA2-EN Doc. No.: ##28730## 20160520 TYPE 3 - WIRING DIAGRAM REMOTE STARTER STARTER (+) OUTPUT TRUNK (-) OUTPUT UNLOCK (-) OUTPUT LOCK (-) OUTPUT 12V (+) GROUND (-) GWR (-) OUTPUT REQUIRED -> HOOD STATUS (-) INPUT TRUNK STATUS (-) INPUT DOOR STATUS (-) INPUT LEGEND NOT REQUIRED IN (1-WAY) NOT REQUIRED IN (2-WAY) USE OR HARD MODE CONNECT TO GROUND TO ENABLE AUTOMATIC RELOCK AFTER START GWR (-) INPUT - BLUE/WHITE (NC) NO GROUND - BLACK 12V (+) - RED LOCK/ARM (-) INPUT - GREEN/BLACK UNLOCK/DISARM (-) INPUT - BLUE/BLACK TRUNK (-) INPUT - RED/WHITE (NC) BROWN (NC) PURPLE/YELLOW GROUND (-) INPUT - PURPLE/BLACK (NC) WHITE STARTER (+) INPUT - BLACK/WHITE (NC) GREEN (NC) PURPLE/WHITE WHITE/BLACK - IGNITION (+) SIDE WHITE/RED - IGNITION (+) VEHICLE SIDE WHITE (NC) YELLOW/BLACK - DOOR STATUS (-) OUTPUT YELLOW/RED - TRUNK STATUS (-) OUTPUT YELLOW - HOOD STATUS (-) OUTPUT BROWN/RED (NC) BROWN/YELLOW (NC) ORANGE/BLACK - KEY DATA ORANGE/WHITE (NC) ORANGE - SWC PINK/BLACK (NC) PINK - IGNITION (+) INPUT BLUE/RED (NC) BLUE/YELLOW (NC) GREEN/RED (NC) GREEN/YELLOW (NC) GRAY/RED (NC) GRAY/YELLOW (NC) KEY DATA SWC 1 2 3 4 5 6 7 IGNITION (+)
Page 10 of 11 ADS-AL(DL)-HA2-EN Doc. No.: ##28730## 20160520 INSTALLATION MODE SELECTION 1 Press and release programming button to select installation mode. LED flashes (1X) once = LED flashes (2X) twice = STANDARD HARD MODE 2! Press and hold programming button until LED turns solid GREEN to register selection. After registration, follow Factory Reset Procedure to change installation mode and restart this procedure. MODULE PROGRAMMING PROCEDURE 1 Insert key into ignition. 3 Wait, LED will turn solid GREEN for 2 seconds. 2 ON Turn key to ON position. 4 5 OFF Turn key to OFF position. Module Programming Procedure completed.
Page 11 of 11 ADS-AL(DL)-HA2-EN Doc. No.: ##28730## 20160520 IDENTIFY VEHICLE YEAR 1 Locate the Vehicle Identification Number (VIN), identify the 10th character then match it to its corresponding year. Æ 4 3 A 5 Y 1 N 5 T A L 8 D 5 R 0 X Æ A 1980 L 1990 Y 2000 A 2010 B 1981 M 1991 1 2001 B 2011 C 1982 N 1992 2 2002 C 2012 D 1983 P 1993 3 2003 D 2013 E 1984 R 1994 4 2004 E 2014 F 1985 S 1995 5 2005 F 2015 G 1986 T 1996 6 2006 G 2016 H 1987 V 1997 7 2007 H 2017 J 1988 W 1998 8 2008 J 2018 K 1989 X 1999 9 2009 K 2019 LED STATUS Flashing RED DIAGNOSTICS DURING PROGRAMMING DURING REMOTE START WITH IGNITION OFF Missing/wrong information from firmware or vehicle Incorrectly programmed Solid RED Waiting for more vehicle information Incorrectly programmed Flashing GREEN Additional steps required to complete programming MODULE DIAGNOSTICS Correctly programmed and operational Incorrectly programmed or connected Not programmed waiting for more vehicle information False ground when running status from remote starter Solid GREEN then OFF Correctly programmed Reset in progress Reset in progress OFF No activity or already programmed Invalid ground when running status from remote starter At rest and ready for a remote start sequence FACTORY RESET PROCEDURE 1 2 DISCONNECT all connectors from module EXCEPT the black 4-PIN standard or optional data connector. DISCONNECT black 4-PIN standard or optional data connector. 5 6 LED will turn solid red for 2 seconds. RESET COMPLETED. RECONNECT all connectors. 3 PRESS AND HOLD programming button while connecting either 4-PIN standard or optional data connector. 7! Repeat programming procedure. Failure to follow procedure may result with a DTC or a CHECK ENGINE error message. 4 When LED flashes red, RELEASE programming button.