Alarms & Remote Start Automotive Data Solutions Inc. HA OL-AL(MDB)-HA-EN AVAILABLE FOR : OL-MDB-ALL Rev. Date: May 0, 06 U.S. PATENT NO. 8,86,780 The brand names and logos found in this guide are property of their respective owners.! NOTICE: The manufacturer will accept no responsibility for any electrical damage resulting from improper installation of this product, be that either damage to the vehicle itself or to the installed device. This device must be installed by a certified technician. This guide has been written for properly trained technicians; a certain level of skill & knowledge is therefore assumed. Please review the Installation Guide carefully before beginning any work.
Page of INSTALL TYPE SELECTION RDX AT 07- HOOD STATUS OUTPUT TRUNK STATUS OUTPUT DOOR STATUS OUTPUT POWER LIFTGATE TRUNK/HATCH RELEASE DOOR LOCK AUTOLIGHT CTRL* DOOR UNLOCK A/M RS CTRL FROM OEM REMOTES DISARM OEM ALARM ARM OEM ALARM INSTALL TYPE 06-07- YEAR MODEL CSX AT/MT MDX AT HONDA MAKE WARNING: This solution does NOT cover hybrid vehicles with a manual transmission. Do not, under any circumstances, attempt to install. ACURA I DATA IMMOBILIZER BYPASS NOTE A/M ALARM CTRL FROM OEM REMOTES FEATURES Civic AT/MT 06- Civic Hybrid AT 06- CR-V AT/MT 07- CR-Z AT -6 Fit AT/MT 09- Insight AT 0- *This feature will unlock then lock the vehicle s doors on RS shutdown. To turn it off, deactivate the RAP shutdown. (See module navigation chart) Use traditional hardwired installation method for feature to be functional during remote start.
ADS-AL(DL)-HA PAGE X-X Page of WARNING: READ CAREFULLY IMPORTANT I Ground When Running from Remote Starter must be provided BEFORE. Failure to comply may result in immobilizer bypass malfunction during remote start. II If Ground When Running from Remote Starter CAN T be provided BEFORE, use a separate TB-HA for immobilizer bypass ONLY. III - DO NOT program unlock before start on the Remote Starter. - DO NOT change Remote Starter OEM alarm control default settings. Failure to comply may result in product malfunction.
Page of NAME TYPE POSITION POLARITY MODULE LOCATION COMPONENT LOCATOR 0 Red 0 0 Lt 0 Red 0 Fit AT/MT 09- Key Data Insight AT 0- Key Data DESCRIPTION YEAR MODEL HONDA MAKE TYPE - CROSS REFERENCE CHART
Page of TYPE - WIRING DIAGRAM REMOTE STARTER STARTER OUTPUT TRUNK (-) OUTPUT UNLOCK (-) OUTPUT LOCK (-) OUTPUT V GROUND (-) GWR (-) OUTPUT REQUIRED -> HOOD STATUS (-) INPUT OPTIONAL -> TRUNK STATUS (-) INPUT OPTIONAL -> DOOR STATUS (-) INPUT N/A LEGEND NOT REQUIRED IN (-WAY) NOT REQUIRED IN (-WAY) USE OR HARD MODE BROWN/RED (NC) BROWN/YELLOW (NC) ORANGE/BLACK - KEY DATA ORANGE/WHITE (NC) ORANGE - PINK/BLACK (NC) PINK - IGNITION INPUT KE Y SW DA C TA BLUE/RED (NC) BLUE/YELLOW (NC) GREEN/RED (NC) GREEN/YELLOW (NC) GRAY/RED (NC) GRAY/YELLOW (NC) 6 7 ) (+ CONNECT TO GROUND TO ENABLE AUTOMATIC RELOCK AFTER START YELLOW/BLACK - DOOR STATUS (-) OUTPUT YELLOW/RED - TRUNK STATUS (-) OUTPUT YELLOW - HOOD STATUS (-) OUTPUT ON LOCK/ARM (-) INPUT - GREEN/BLACK UNLOCK/DISARM (-) INPUT - BLUE/BLACK TRUNK (-) INPUT - RED/WHITE (NC) BROWN (NC) PURPLE/YELLOW GROUND (-) INPUT - PURPLE/BLACK (NC) WHITE STARTER INPUT - BLACK/WHITE (NC) GREEN (NC) PURPLE/WHITE WHITE/BLACK - IGNITION SIDE WHITE/RED - IGNITION VEHICLE SIDE WHITE (NC) TI GWR (-) INPUT - BLUE/WHITE (NC) NO GROUND - BLACK V - RED IG NI
Page 6 of TYPE POSITION POLARITY MODULE LOCATION COMPONENT LOCATOR 0 Brown At immobilizer At immobilizer 0 Lt At immobilizer MDX AT 07- Key Data NAME YEAR MODEL MAKE ACURA DESCRIPTION TYPE - CROSS REFERENCE CHART
Page 7 of TYPE - WIRING DIAGRAM REMOTE STARTER STARTER OUTPUT DISARM (-) OUTPUT TRUNK (-) OUTPUT UNLOCK (-) OUTPUT LOCK (-) OUTPUT V GROUND (-) GWR (-) OUTPUT REQUIRED -> HOOD STATUS (-) INPUT OPTIONAL -> TRUNK STATUS (-) INPUT OPTIONAL -> DOOR STATUS (-) INPUT N/A LEGEND NOT REQUIRED IN (-WAY) NOT REQUIRED IN (-WAY) USE OR HARD MODE YELLOW/BLACK - DOOR STATUS (-) OUTPUT YELLOW/RED - TRUNK STATUS (-) OUTPUT YELLOW - HOOD STATUS (-) OUTPUT BROWN/RED (NC) BROWN/YELLOW (NC) ORANGE/BLACK - KEY DATA ORANGE/WHITE (NC) ORANGE - PINK/BLACK (NC) PINK - IGNITION INPUT KE Y DA SW TA C BLUE/RED (NC) BLUE/YELLOW (NC) GREEN/RED (NC) GREEN/YELLOW (NC) GRAY/RED (NC) GRAY/YELLOW (NC) 6 7 ON (+ ) TI LOCK/ARM (-) INPUT - GREEN/BLACK UNLOCK (-) INPUT - BLUE/BLACK TRUNK (-) INPUT - RED/WHITE DISARM (-) INPUT - BROWN (NC) PURPLE/YELLOW (NC) PURPLE/BLACK (NC) WHITE STARTER INPUT - BLACK/WHITE (NC) GREEN (NC) PURPLE/WHITE WHITE/BLACK - IGNITION SIDE WHITE/RED - IGNITION VEHICLE SIDE WHITE (NC) NI GWR (-) INPUT - BLUE/WHITE (NC) NO GROUND - BLACK V - RED IG
Page 8 of NAME TYPE POSITION POLARITY MODULE LOCATION COMPONENT LOCATOR 0 Yellow 0 Pink 0 Yellow 07- Key Data CSX AT/MT Civic Hybrid AT CR-V AT/MT CR-Z AT 06- Key Data DESCRIPTION YEAR RDX AT Civic AT/MT HONDA MODEL ACURA MAKE TYPE - CROSS REFERENCE CHART 0 Pink 0 Yellow 0 Pink 0 Yellow 0 Pink 0 LtBlue 0 0 Pink 0 Yellow 0 Pink 0 06- Key Data 06- Key Data 07- Key Data -6 Key Data
Page 9 of TYPE - WIRING DIAGRAM REMOTE STARTER STARTER OUTPUT TRUNK (-) OUTPUT UNLOCK (-) OUTPUT LOCK (-) OUTPUT V GROUND (-) GWR (-) OUTPUT REQUIRED -> HOOD STATUS (-) INPUT OPTIONAL -> TRUNK STATUS (-) INPUT OPTIONAL -> DOOR STATUS (-) INPUT N/A LEGEND NOT REQUIRED IN (-WAY) NOT REQUIRED IN (-WAY) USE OR HARD MODE BROWN/RED (NC) BROWN/YELLOW (NC) ORANGE/BLACK - KEY DATA ORANGE/WHITE (NC) ORANGE - PINK/BLACK (NC) PINK - IGNITION INPUT KE Y SW DA C TA BLUE/RED (NC) BLUE/YELLOW (NC) GREEN/RED (NC) GREEN/YELLOW (NC) GRAY/RED (NC) GRAY/YELLOW (NC) 6 7 ) (+ CONNECT TO GROUND TO ENABLE AUTOMATIC RELOCK AFTER START YELLOW/BLACK - DOOR STATUS (-) OUTPUT YELLOW/RED - TRUNK STATUS (-) OUTPUT YELLOW - HOOD STATUS (-) OUTPUT ON LOCK/ARM (-) INPUT - GREEN/BLACK UNLOCK/DISARM (-) INPUT - BLUE/BLACK TRUNK (-) INPUT - RED/WHITE (NC) BROWN (NC) PURPLE/YELLOW GROUND (-) INPUT - PURPLE/BLACK (NC) WHITE STARTER INPUT - BLACK/WHITE (NC) GREEN (NC) PURPLE/WHITE WHITE/BLACK - IGNITION SIDE WHITE/RED - IGNITION VEHICLE SIDE WHITE (NC) TI GWR (-) INPUT - BLUE/WHITE (NC) NO GROUND - BLACK V - RED IG NI
XX-XX ADS-AL(DL) ADS-AL(TB)-GM 69 ADS-DL-GM 69 ADS-DL-HA 69 ADS-TB-GM PAGE X-X 69 Page 0 of INSTALLATION MODE SELECTION Press and release programming button to select installation mode. LED flashes (X) once = LED flashes (X) twice = STANDARD HARD MODE! Press and hold programming button until LED turns solid GREEN to register selection. After registration, follow Factory Reset Procedure to change installation mode and restart this procedure. MODULE PROGRAMMING PROCEDURE Insert key into ignition. Turn key to ON position. Wait, LED will turn solid GREEN for seconds. OFF Turn key to OFF position. ON Module Programming Procedure completed.
XX-XX CLASSIC - PAGE X-X Page of IDENTIFY VEHICLE YEAR Locate the Vehicle Identification Number (VIN), identify the 0th character then match it to its corresponding year. Æ AYNTAL8DR0X Æ A 980 L 990 Y 000 A 00 B 98 M 99 00 B 0 C 98 N 99 00 C 0 D 98 P 99 00 D 0 E 98 R 99 00 E 0 F 98 S 99 00 F 0 G 986 T 996 6 006 G 06 H 987 V 997 7 007 H 07 J 988 W 998 8 008 J 08 K 989 X 999 9 009 K 09 MODULE DIAGNOSTICS LED STATUS DIAGNOSTICS DURING PROGRAMMING DURING REMOTE START WITH IGNITION OFF Flashing RED Missing/wrong information from firmware or vehicle Incorrectly programmed Incorrectly programmed or connected Solid RED Waiting for more vehicle information Incorrectly programmed Not programmed waiting for more vehicle information Flashing GREEN Additional steps required to complete programming Correctly programmed and operational False ground when running status from remote starter Solid GREEN then OFF Correctly programmed Reset in progress Reset in progress OFF No activity or already programmed Invalid ground when running status from remote starter At rest and ready for a remote start sequence LED will turn solid red for seconds. RESET COMPLETED. 6 RECONNECT all connectors. DISCONNECT black -PIN standard or optional data connector. DISCONNECT all connectors from module EXCEPT the black -PIN standard or optional data connector. FACTORY RESET PROCEDURE PRESS AND HOLD programming button while connecting either -PIN standard or optional data connector. 7 Repeat programming procedure.! Failure to follow procedure may result with a DTC or a CHECK ENGINE error message. When LED flashes red, RELEASE programming button.