DKG/DVG Fluid Dry Coolers

DKG/DVG Fluid Dry Coolers

SPECIFICATION Introduction Due to the many combinations of temperatures, flow rates and working fluids which may be encountered, it is not possible to catalogue capacities and correction factors to satisfy all conditions. For this reason only summary capacity figures are given in this brochure. For complete capacity information please refer to our Selection Software Program for Dry Coolers. This is available on request and enables selections to be made based on different, userdefined conditions. Alternatively, please contact your supplier. General A dry cooler is a forced convection air-cooled fluid cooler. Air is forced over a finned coil which contains the working fluid such as water or water and glycol mix. In determining the working fluid, consideration must be given to the lowest ambient that could possibly be experienced by the unit, in order to minimise the risk of freezing the working fluid. This brochure provides information on the DKG and DVG ranges of dry coolers. The DKG range of flat-bed dry coolers is modular in design, having 1 to 5 fans arranged in a single bank, and 4 to 12 fans arranged in a double bank. The DVG V-bank range is also modular, having either 900mm fans (arranged in double rows giving 4 to 12 fans) or 1000mm fans (arranged in a single row giving 2 to 5 fans). In addition, where space is severely limited, DVG models are available with taller coils. This taller range, known as the DVH, provides up to 25% greater capacity for the same footprint. For selections on the DVH range please contact your supplier. The two-speed motors can be used either for night-time turn down or for control of temperature. Night-time turn down can offer an acceptable day-time noise level with a considerably lower night-time sound emittance. Also substantial power savings can be achieved during periods of low ambient temperatures. All models have many circuiting options which can be selected to optimise duty with required fluid pressure drops and flow rates. All models can be supplied with stub, BSP male or flange type connections. BSP connections are available on headers with a diameter less than 2". Flange or stub type connections are normally recommended on headers with a diameter greater than 2". Casework All casework is manufactured from corrosion-resistant pregalvanised steel. Painted components feature hard wearing, oven cured, UV-tolerant paint, applied in our electrostatic paint plant, which protects surfaces and cut edges. Each fan chamber is separated by internal baffle plates to prevent windmilling of off-cycle fans. On the DKG an optional coil cleaning port in the form of a hinged access panel can be provided in each fan section and optional leg extensions are available to enhance fresh air supply in difficult locations. Coils Standard coils (Cu/Al) are manufactured from copper tubes which are mechanically expanded into fully-collared holes in aluminium fins. This ensures an effective and permanent bond between the tube and the fin, maximising heat transfer characteristics. Alternative fin materials are available to give added protection in saline or polluted atmospheres:- Cu/Av Copper tube/vinyl coated aluminium fins Cu/Cu Copper tubes/copper fins Cu/Et Copper tubes/copper fins electrotinned after assembly Motors and Speed Control DKG motors (6, 8, 12 and 16 pole) are foot-mounted onto rigid diagonal cross beams and, as standard, individually wired to a common terminal box on the outside of the unit (fluid connection end). Optionally, motors may be individually wired to 6 pole, 3 phase isolators. DVG motors are three phase external rotor type, available in 6, 8 and 12 pole speeds. All motors feature internal protection, making them suitable for variable speed control. This can be wired via the standard terminal box at the end of the unit. Two speed operation is achieved by remote switching of motors between Delta and Star connections. For this purpose, Searle offers a two-speed contactor box consisting of a mains isolator, motor circuit breakers and mechanically and electrically interlocked changeover contactors for each fan. For customer s own two-speed systems the use of an alternative terminal box is required - this should be specified at the time of ordering. (The DVG also requires an alternative wiring harness). The two-speed control can be used in conjunction with the Searle range of microprocessor fan control systems which gives very close control of temperature. If a Searle control is not used, it is essential that the system selected has both mechanical and electrical interlocks to give maximum protection to the motors. Fluid temperature controls are available which range from a simple contactor box to a sophisticated microprocessor based sequential system, operating from temperature sensors. Please refer to Searle s Controls brochure or contact your supplier for further assistance. 3ph fan speed control is also available as an option. Noise levels Data for sound pressure levels has been derived from measurements taken during independent testing carried out in free field conditions according to EN13487. Published figures are for distances measured horizontally at fan deck height from the longest side of a horizontal unit, when mounted on a reflective plan. For approximate noise levels in the direction of air flows add 6dB(A). Standard Catalogue Conditions The selection conditions shown in this brochure are: Ambient Air Temperature 32 C Working Fluid - Entering Temperature 48 C Working Fluid - Leaving Temperature 43 C Working Fluid Ethylene glycol 34% by weight In the selection tables, duty and air volumes are shown only for models identified in bold type. Noise levels apply to all models shown on each line. 2

HOW TO ORDER MOTOR TYPE AND POLE (C6, E6, E8, C8, C12) NUMBER OF ROWS IN COIL (2, 3 or 4) FANS PER BANK (2, 3, 4, 5 or 6) BANKS OF FANS (1 or 2) TYPE DVG 1 2 4 C8 DKG 255-12 H - Options for DKG and DVG: AI 400/50 2S FCP DS P TYPE MODEL MOTOR POLES (4, 6, 8, 12 or 16) ORIENTATION H = Horizontal V = Vertical COIL MATERIAL AI = Copper tubes/aluminium fins AV = Copper tubes/vinyl coated aluminium fins Cu = Copper tubes/copper fins ET = Copper tubes/copper fins ELECTRICAL SUPPLY (V/Hz) 400/50 400/60 230/50 230/60 COIL CIRCUITING 2S = 2 Section (standard) CONTROLS CB Contactor Box FCT Intelligent Fan Control (Temperature Sensing) FS Fan Speed Control (3ph) (Triac or Inverter) WIRING OPTIONS D = Delta S = Star DS = Dual Speed ISO = Isolators PACKING 3

DKG - SELECTION DATA Model Modèle Modell No. of fans Duty Puissance Leistung kw Air Volume Débit d'air Luftmenge m³/s D E L T A (High Speed) Sound Pressure Level (db(a), NC & NR @ 10m) Niveau de Pression Sonore (db(a), NC & NR @ 10m) Schalldruckpegel (db(a), NC & NR @ 10m) Octave Band Frequency (Hz) Bande de Fréquence (Hz) 10M Oktavband Frequenz (Hz) Duty Puissance Leistung Air Volume Débit d'air Luftmenge S T A R (Low Speed) Sound Pressure Level (db(a), NC & NR @ 10m) Niveau de Pression Sonore (db(a), NC & NR @ 10m) Schalldruckpegel (db(a), NC & NR @ 10m) Octave Band Frequency (Hz) Bande de Fréquence (Hz) 10M Oktavband Frequenz (Hz) 63 125 250 500 1K 2K 4K 8K db(a) NC NR kw m³/s 63 125 250 500 1K 2K 4K 8K db(a) NC NR 6 Pole 6D 6S 10, 20, 30 1 x 1 69.9 5.9 51 56 53 49 48 44 39 38 53 48 49 59.3 4.7 45 51 48 44 43 38 34 33 48 43 44 40, 50, 60 1 x 2 140.8 11.7 54 59 56 52 51 47 42 41 56 51 52 119.5 9.3 48 54 51 47 46 41 37 36 51 46 47 70, 80, 90 1 x 3 212.4 17.6 55 61 58 54 53 48 43 43 58 53 54 180.5 14.0 50 56 53 49 48 43 38 38 52 48 49 110, 120 1 x 4 265.1 23.4 56 62 59 55 54 50 44 44 59 54 55 245.3 18.6 51 57 54 50 49 44 40 39 54 49 50 115, 125 2 x 2 281.5 23.4 56 62 59 55 54 49 44 44 58 54 55 239.0 18.6 51 57 54 49 49 44 39 39 53 49 50 140, 150 1 x 5 338.8 29.3 57 63 60 56 55 51 45 45 60 55 56 282.4 23.3 52 58 55 51 50 45 41 40 54 50 51 175, 185 2 x 3 424.9 35.1 58 64 60 57 56 51 46 46 60 56 57 361.0 27.9 53 59 55 51 51 46 41 40 55 50 51 205, 215 2 x 4 530.1 46.8 59 65 61 58 57 52 47 47 61 57 58 490.5 37.2 54 60 57 52 52 47 42 41 56 52 53 235, 245 2 x 5 677.6 58.5 60 66 62 59 58 53 48 48 62 58 59 574.2 46.5 55 61 58 53 53 48 43 42 57 53 54 265, 275 2 x 6 825.6 70.2 61 66 63 60 59 54 49 49 63 58 59 698.8 55.8 56 62 58 54 53 48 44 43 58 53 54 8 Pole 10, 20, 30 1 x 1 58.3 4.6 48 50 47 45 44 38 32 22 48 44 45 44.4 3.3 42 43 40 38 37 32 26 15 41 37 38 40, 50, 60 1 x 2 117.5 9.2 51 53 50 48 47 41 35 25 51 47 48 90.7 6.5 45 46 43 41 40 35 29 18 44 40 41 70, 80, 90 1 x 3 177.6 13.8 53 54 51 50 48 43 37 27 52 48 49 135.4 9.8 46 48 45 43 41 37 31 20 46 41 42 110, 120 1 x 4 241.3 18.4 54 56 53 51 50 44 38 28 54 50 51 183.6 13.0 48 49 46 44 43 38 32 21 47 43 44 115, 125 2 x 2 235.1 18.4 54 55 52 51 49 44 38 28 53 49 50 181.5 13.0 47 49 46 44 42 37 32 21 46 42 43 140, 150 1 x 5 282.4 23.0 55 57 54 52 51 45 39 29 55 51 52 214.4 16.3 49 50 47 45 44 39 33 22 48 44 45 175, 185 2 x 3 355.1 27.6 55 57 54 52 51 45 40 30 55 51 52 270.9 19.5 49 50 48 45 44 39 33 22 48 44 45 205, 215 2 x 4 482.5 36.8 57 58 55 54 52 47 41 31 56 52 53 367.2 26.0 50 51 49 46 45 40 35 24 49 45 46 235, 245 2 x 5 564.7 46.0 57 59 56 54 53 48 42 32 57 53 54 428.8 32.5 51 52 50 47 46 41 35 25 50 46 47 265, 275 2 x 6 687.2 55.2 58 60 57 55 54 48 43 33 58 54 55 520.9 39.0 52 53 50 48 47 42 36 25 51 47 48 12 Pole 10, 20, 30 1 x 1 41.6 3.0 41 42 40 37 36 31 25 14 40 36 37 32.2 2.2 31 33 30 26 26 21 15 4 30 25 27 40, 50, 60 1 x 2 85.1 6.0 44 45 43 40 39 34 28 17 43 39 40 65.8 4.4 34 36 33 29 29 24 18 7 33 28 30 70, 80, 90 1 x 3 128.7 9.0 45 47 44 41 41 35 30 19 45 40 41 99.6 6.6 35 37 35 31 31 25 20 9 35 30 31 100, 110, 120 1 x 4 172.2 12.0 47 48 46 43 42 37 31 20 46 42 43 133.3 8.8 36 39 36 32 32 27 21 10 36 32 33 105, 115, 125 2 x 2 170.1 12.0 46 48 45 42 41 36 31 20 45 41 42 131.7 8.8 36 38 36 32 31 26 21 10 35 31 32 130, 140, 150 1 x 5 215.9 15.0 48 49 47 44 43 38 32 21 47 43 44 167.1 11.0 37 40 37 33 33 28 22 11 37 33 34 165, 175, 185 2 x 3 257.4 18.0 48 50 47 44 43 38 33 21 47 43 44 199.3 13.2 38 40 37 34 33 28 22 11 37 33 34 195, 205, 215 2 x 4 344.4 24.0 49 51 48 45 44 39 34 22 48 44 45 266.6 17.6 39 41 38 35 34 29 23 13 38 34 35 225, 235, 245 2 x 5 402.0 30.0 50 52 49 46 45 40 35 23 49 45 46 311.2 22.0 40 42 39 36 35 30 24 14 39 35 36 255, 265, 275 2 x 6 488.2 36.0 51 53 50 47 46 41 36 24 50 46 47 377.9 26.4 41 43 40 36 36 31 25 14 40 36 37 16 Pole 10, 20, 30 1 x 1 32.8 2.3 34 35 32 29 28 24 18 7 32 27 29 26.4 1.8 27 29 26 23 22 17 12 0 26 21 23 40, 50, 60 1 x 2 67.1 4.5 37 38 35 32 31 27 21 10 35 31 32 54.0 3.5 30 32 29 26 25 20 15 3 29 24 26 70, 80, 90 1 x 3 101.5 6.8 38 40 37 34 33 29 22 11 37 33 34 81.7 5.3 32 33 31 27 27 22 17 4 31 25 27 100, 110, 120 1 x 4 135.8 9.0 39 41 38 35 34 30 23 12 38 34 35 109.3 7.0 33 34 32 28 28 23 18 6 32 27 29 105, 115, 125 2 x 2 134.1 9.0 39 41 38 34 34 30 23 12 38 34 35 108.0 7.0 33 34 32 28 27 23 18 5 32 27 28 130, 140, 150 1 x 5 170.2 11.3 40 42 39 36 35 31 24 13 39 35 36 137.0 8.8 34 35 33 29 29 24 19 7 33 28 30 165, 175, 185 2 x 3 203.0 13.5 41 42 40 36 35 31 25 14 40 35 36 163.4 10.5 35 36 33 30 29 25 19 7 33 29 30 195, 205, 215 2 x 4 271.6 18.0 42 43 41 37 37 32 26 15 41 37 38 218.6 14.0 36 37 35 31 30 26 21 8 35 30 31 225, 235, 245 2 x 5 317.0 22.5 43 44 42 38 38 33 27 16 42 37 38 255.1 17.5 37 38 36 32 31 27 21 9 36 31 32 255, 265, 275 2 x 6 384.9 27.0 44 45 43 39 38 34 28 17 43 38 39 309.8 21.0 37 39 36 33 32 28 22 10 36 32 33 Motor Details - (380-415V, 3ph, 50Hz) Type Pole Nominal Speed Vitesse Nominale Nenndrehzahl Delta (High Speed) Power Input Puissance Absorbée Leistungsaufnahme FLC Intensité Betriebsstrom 8D 12D 16D SC Intensité de démarrage Anlaufstrom Nominal Speed Vitesse Nominale Nenndrehzahl Star (Low Speed) Power Input Puissance Absorbée Leistungsaufnahme FLC Intensité Betriebsstrom 8S 12S 16S SC Intensité de démarrage Anlaufstrom rpm t/mn UpM kw A A rpm t/mn UpM kw A A 6 930 2.45 5.4 25.0 780 1.75 3.2 15.0 8 680 1.65 3.3 11.0 500 1.15 2.0 3.4 12 460 0.80 2.4 4.2 335 0.47 1.2 1.4 16 330 0.49 1.7 2.5 250 0.27 0.7 0.8 4

DVG - SELECTION DATA Model Modèle Modell No. of fans Duty Puissance Leistung kw Air Volume Débit d'air Luftmenge m³/s D E L T A (High Speed) Sound Pressure Level (db(a), NC & NR @ 10m) Niveau de Pression Sonore (db(a), NC & NR @ 10m) Schalldruckpegel (db(a), NC & NR @ 10m) Octave Band Frequency (Hz) Bande de Fréquence (Hz) 10M Oktavband Frequenz (Hz) Duty Puissance Leistung Air Volume Débit d'air Luftmenge S T A R (Low Speed) Sound Pressure Level (db(a), NC & NR @ 10m) Niveau de Pression Sonore (db(a), NC & NR @ 10m) Schalldruckpegel (db(a), NC & NR @ 10m) Octave Band Frequency (Hz) Bande de Fréquence (Hz) 10M Oktavband Frequenz (Hz) 63 125 250 500 1K 2K 4K 8K db(a) NC NR kw m³/s 63 125 250 500 1K 2K 4K 8K db(a) NC NR 6 Pole - High Power (900mm) C6D 222, 223, 224 2 x 2 345.5 26.6 51 53 60 56 57 57 53 46 62 59 60 - - - - - - - - - - - - - 232, 233, 234 2 x 3 537.1 39.8 52 54 61 58 59 58 55 48 64 60 62 - - - - - - - - - - - - - 242, 243, 244 2 x 4 691.7 53.1 54 56 63 59 60 60 56 49 65 62 63 - - - - - - - - - - - - - 252, 253, 254 2 x 5 850.2 66.4 55 57 64 60 61 61 57 50 66 63 64 - - - - - - - - - - - - - 262, 263, 264 2 x 6 1034.2 79.7 55 57 64 61 62 61 58 50 67 63 65 - - - - - - - - - - - - - 6 Pole - Low Noise (900mm) E6D E6S 222, 223, 224 2 x 2 262.9 18.7 46 49 53 49 52 52 46 35 57 54 56 210.9 14.2 47 48 49 47 47 44 36 31 51 47 48 232, 233, 234 2 x 3 398.4 28.1 48 50 55 51 54 54 48 36 59 56 58 319.6 21.2 49 50 51 49 48 45 38 33 53 48 49 242, 243, 244 2 x 4 524.9 37.4 49 52 56 52 55 55 49 38 60 57 59 421.1 28.3 50 51 52 50 50 47 39 34 54 50 51 252, 253, 254 2 x 5 637.3 46.8 50 53 57 53 56 56 50 38 61 58 60 511.2 35.4 51 52 53 51 51 48 40 35 55 50 51 262, 263, 264 2 x 6 773.0 56.1 51 53 58 54 56 57 50 39 62 59 60 620.1 42.5 52 53 54 52 51 48 41 36 55 51 52 8 Pole (900mm) E8D E8S 222, 223, 224 2 x 2 200.5 13.4 50 50 50 46 44 41 34 33 49 44 45 155.4 10.0 45 46 43 41 40 35 27 21 44 40 41 232, 233, 234 2 x 3 303.8 20.1 52 52 52 47 46 43 36 35 51 46 47 235.5 15.0 47 48 45 42 42 37 29 22 46 41 42 242, 243, 244 2 x 4 400.3 26.8 53 53 53 49 47 44 37 36 52 47 48 310.3 20.0 48 49 46 44 43 38 30 24 47 43 44 252, 253, 254 2 x 5 486.0 33.5 54 54 54 50 48 45 38 37 53 48 49 376.7 25.0 49 50 47 45 44 39 31 24 48 44 45 262, 263, 264 2 x 6 589.5 40.2 55 55 55 50 49 46 39 37 54 49 50 456.9 30.0 50 51 48 45 44 39 32 25 48 44 45 8 Pole (1000mm) C8D C8S 122, 123, 124 1 x 2 258.2 16.7 53 54 53 52 51 48 44 35 56 51 52 220.4 14.0 43 49 51 47 45 44 40 28 51 46 47 132, 133, 134 1 x 3 391.1 25.1 55 56 55 54 53 50 46 37 58 53 54 333.8 21.0 45 51 53 49 47 46 42 30 53 47 49 142, 143, 144 1 x 4 506.8 33.4 56 57 56 55 54 51 47 38 59 54 55 432.6 28.0 46 52 54 50 48 47 43 31 54 49 50 152, 153, 154 1 x 5 613.5 41.8 57 58 57 56 55 52 48 39 60 55 56 523.7 35.0 47 53 55 51 49 48 44 32 55 50 51 12 Pole (900mm) C12D C12S 222, 223, 224 2 x 2 176.7 11.6 44 44 43 44 42 35 29 23 46 42 43 144.3 9.2 40 40 39 40 37 27 23 9 41 37 38 232, 233, 234 2 x 3 267.8 17.3 45 46 45 46 44 37 31 24 48 44 45 218.7 13.8 42 42 40 42 39 29 24 11 43 39 40 242, 243, 244 2 x 4 352.8 23.1 47 47 46 47 45 38 32 26 49 45 46 288.1 18.4 43 43 42 43 40 30 26 12 44 40 41 252, 253, 254 2 x 5 428.3 28.9 48 48 47 48 46 39 33 26 50 46 47 349.8 23.0 44 44 42 44 41 31 27 13 45 41 42 262, 263, 264 2 x 6 519.5 34.7 48 49 48 49 47 40 33 27 51 47 48 424.3 27.6 44 45 43 45 42 32 27 14 46 42 43 12 Pole (1000mm) C12D C12S 122, 123, 124 1 x 2 181.4 11.2 39 44 50 40 40 34 26 17 45 41 42 135.9 8.3 34 38 39 36 35 29 19 10 39 35 36 132, 133, 134 1 x 3 274.8 16.7 41 46 52 41 41 36 28 19 47 43 44 205.9 12.4 36 40 41 38 37 31 21 12 41 37 38 142, 143, 144 1 x 4 356.1 22.3 42 47 53 43 43 37 29 20 48 45 45 266.7 16.5 37 41 42 39 38 32 22 13 42 38 39 152, 153, 154 1 x 5 431.0 27.9 43 48 54 43 44 38 30 21 49 46 46 322.9 20.6 38 42 43 40 39 33 23 14 43 39 40 Motor Details (380-415V, 3ph, 50Hz) Type Pole Nominal Speed Vitesse Nominale Nenndrehzahl Delta (High Speed) Power Input Puissance Absorbée Leistungsaufnahme FLC Intensité Betriebsstrom SC Intensité de démarrage Anlaufstrom Nominal Speed Vitesse Nominale Nenndrehzahl Star (Low Speed) Power Input Puissance Absorbée Leistungsaufnahme FLC Intensité Betriebsstrom SC Intensité de démarrage Anlaufstrom rpm t/mn UpM kw A A rpm t/mn UpM kw A A 6 High Power 880 3.60 7.6 20.0 - - - - 6 Low Noise 880 1.60 3.5 11.0 670 1.00 2.0 4.0 8 (900mm) 660 0.84 2.1 5.0 450 0.45 1.1 2.0 8 (1000mm) 660 2.30 4.5 13.0 550 1.50 2.8 5.0 12 (900mm) 440 0.70 1.8 5.0 350 0.45 1.0 2.0 12 (1000mm) 430 0.82 2.2 5.0 320 0.49 1.2 2.0 5

DKG - DIMENSIONS DKG Layout Horizontal Units Vertical Units (not suitable for operation with 16 pole (star/delta) or 12 pole (star) motors) 6

DVG - DIMENSIONS DVG Layout Note: Forklift channels are load bearing DVG1XX DVG2XX 7

DIMENSIONS AND WEIGHTS DKG Dimensions / Dimensions / Abmessungen (mm) A B C D E F G H J K 6 + 8 Pole/Pole/polig Weights / Masse / Gewicht (kg) Cu / Al Cu / Cu 12 + 16 Pole/Pole/polig 6 + 8 Pole/Pole/polig 12 + 16 Pole/Pole/polig 10 1 x 1 1203 1158 1078 1123 1153 201 190 254 243 20 1 x 1 1203 1158 1078 1123 1153 222 206 301 275 30 1 x 1 1203 1158 1078 1123 1153 242 224 345 315 40 1 x 2 2403 1158 1078 2323 2353 332 320 449 427 50 1 x 2 2403 1158 1078 2323 2353 382 352 539 489 60 1 x 2 2403 1158 1078 2323 2353 420 387 627 568 70 1 x 3 3603 1158 1078 3523 3553 460 451 630 612 80 1 x 3 3603 1158 1078 3523 3553 543 495 779 703 90 1 x 3 3603 1158 1078 3523 3553 602 551 913 823 100 1 x 4 4803 1158 1078 4723 2361 4753 2353 2400-605 - 819 105 2 x 2 2403 2301 2221 2323 2353-560 - 773 110 1 x 4 4803 1158 1078 4723 2361 4753 2353 2400 726 667 1040 941 115 2 x 2 2403 2301 2221 2323 2353 683 623 997 897 120 1 x 4 4803 1158 1078 4723 2361 4753 2353 2400 806 738 1221 1101 125 2 x 2 2403 2301 2221 2323 2353 759 693 1174 1056 130 1 x 5 6003 1158 1078 5923 2361 5953 2353 2353 1247-755 - 1022 140 1 x 5 6003 1158 1078 5923 2361 5953 2353 2353 1247 908 830 1301 1174 150 1 x 5 6003 1158 1078 5923 2361 5953 2353 2353 1247 1003 921 1522 1374 165 2 x 3 3603 2301 2221 3523 3553 1752-800 - 1120 175 2 x 3 3603 2301 2221 3523 3553 1752 982 848 1453 1260 185 2 x 3 3603 2301 2221 3523 3553 1752 1099 997 1720 1540 195 2 x 4 4803 2301 2221 4723 2361 4753 2353 2400-1134 - 1489 205 2 x 4 4803 2301 2221 4723 2361 4753 2353 2400 1301 1182 1929 1731 215 2 x 4 4803 2301 2221 4723 2361 4753 2353 2400 1462 1325 2291 2050 225 2 x 5 6003 2301 2221 5923 2361 2361 1200 5953 2353 2353 1247-1318 - 1851 235 2 x 5 6003 2301 2221 5923 2361 2361 1200 5953 2353 2353 1247 1623 1467 2408 2154 245 2 x 5 6003 2301 2221 5923 2361 2361 1200 5953 2353 2353 1247 1813 1648 2849 2554 255 2 x 6 7203 2301 2221 7123 2361 2361 2400 7153 2353 2353 2447-1556 - 2196 265 2 x 6 7203 2301 2221 7123 2361 2361 2400 7153 2353 2353 2447 1920 1736 2862 2563 275 2 x 6 7203 2301 2221 7123 2361 2361 2400 7153 2353 2353 2447 2148 1950 3392 3037 M DVG Model Dimensions / Dimensions / Abmessungen (mm) A B C D Lifting Centre Mounting Centre Zone de levage Trous de fixation Lifting Centre Mounting Centre (mm) (mm) Length Longueur Length (mm) Mounting Centre Trous de fixation Mounting Centre (mm) Weights / Masse / Gewicht (kg) Cu/Al Cu/Cu xx2 xx3 xx4 xx2 xx3 xx4 12 x 2884 2834 2839 662 778 894 804 974 1156 13 x 4324 1440 1440 878 1050 1222 1074 1344 1614 14 x 5764 2880 2880 1186 1416 1646 1448 1808 2172 15 x 7204 4320 4320 1468 1754 2040 1796 2248 2696 22 x 2404 2354 2359 804 902 998 912 1066 1216 23 x 3604 1200 1200 1131 1275 1419 1294 1522 1748 24 x 4804 2400 2400 1547 1739 1929 1765 2069 2367 25 x 6004 3600 3600 1817 2057 2297 2089 2467 2845 26 x 7204 4800 4800 2400 2172 2458 2744 2500 2952 3400 Searle Manufacturing Company Newgate Lane Fareham Hampshire PO14 1AR UK Telephone +44 (0)1329 823344 Facsimile +44 (0)1329 821242 Email sales@searle.co.uk Website http://www.searle.co.uk We reserve the right to change in whole or part, the specification detailed in this brochure without prior notice and, when necessary to achieve continuous production, to use alternative competitive designs of sub contract components made by various manufacturers. Bulletin No. DKG/DVG APR99/01 Part No. 273-102-035