sales@reliablecraneservice.com 2-525-8 or 2--2516 product guide contents Features 2 Specifications 3 Dimensions 5 Working Range 6 Bifold Load Charts 7 features ton (75 mt) capacity 41 ft-128 ft (12.6 m-39. m) 4 section, full power boom 33 ft-56 ft (. m-17. m) offsettable lattice swingaway extension ft (6.1 m) or ft (12.2 m) extension inserts Grove MEGAFORM boom 18, lb (8 165 kg) hydraulic removable counterweight 275 bhp (5 kw) Tier III Cummins diesel engine Working Range 8 Bifold & Inserts Load Charts Load Handling 11 Rough Terrain Hydraulic Crane www.manitowoccranegroup.com 2--2516 or 2-525-8
sales@reliablecraneservice.com 2-525-8 or 2--2516 features 2 The Grove MEGAFORM boom shape eliminates weight and increases capacity compared to conventional shapes. For improved operator comfort and visibility of the boom load the cab can be tilted up to. Max. tip height of 232 ft (.6 m) w/56 ft (17. m) bi-fold and (2) ft (6.1 m) inserts. Electronically controlled Cummins diesel engine provides plenty of power at the jobsite. 5533 (supersedes 5489) 8 N6 218 HSL Link-Belt Cranes 2--2516 or 2-525-8 2
sales@reliablecraneservice.com 2-525-8 or 2--2516 specifications Superstructure B Boom 41 ft. - 128 ft. (12.6 m - 39. m) four-section, sequenced synchronized full power boom. Maximum tip height: 138 ft. (41.9 m). Lattice Extension 33 ft.-56 ft. (. m-17 m) offsettable bifold lattice swingaway extension. Offsets,, and. Stows alongside base boom section. Maximum tip height: 192 ft. (58.6 m). *Optional Lattice Extension Inserts (2) x ft. (6.1 m) lattice extension inserts. Installs between the boom nose and bifold extension, non-stowable. Maximum tip height: 232 ft. (.6 m). B Boom Nose Four nylatron sheaves mounted on heavy-duty tapered roller bearings with removable pin-type rope guards. Quick-reeving type boom nose. Removable auxiliary boom nose with removable pin type rope guard. Boom Elevation One double-acting hydraulic cylinder with integral holding valve provides elevation from -3 to +78. Load Moment & Anti-Two Block System Standard Graphic Display load moment and anti-two block system with audio-visual warning and control lever lockout. These systems provide electronic display of boom angle, length, radius, tip height, relative load moment, maximum permissible load, load indication and warning of impending two-block condition. The standard Work Area Definition System allows the operator to pre-select and define safe working areas. If the crane approaches the pre-set limits, audio-visual warnings aid the operator in avoiding job-site obstructions. C Cab Full-vision, all-steel fabricated with acoustical lining and tinted safety glass throughout. Cab tilts to + degrees. Deluxe seat incorporates armrest-mounted hydraulic single-axis controllers. Dash panel incorporates gauges for all engine functions. Other standard features include: hot water heater, cab circulating air fan, sliding side and rear windows, sliding skylight with electric wiper and sunscreen, electric windshield wash/wipe, fire extinguisher and seat belt. Swing Two speed, planetary swing drive with foot-applied multi-disc wet brake. Spring applied, hydraulically-released swing brake. Single position mechanical house lock, operated from cab. Maximum speed: 2. RPM. Counterweight 18, lbs. (8 165 kg). Hydraulically installed and removed. Hydraulic System Two main pumps ([1] piston and [1] gear) with a combined capacity of 133 GPM (3 LPM). Maximum operating pressure: psi (277.7 bar). Three section pressure compensated valve bank. Return line type filter with full flow by-pass protection and service indicator. Replaceable cartridge with micron filtration rating of 5/12/16. 263 gallon (995 L) hyd. reservoir. Carrier mounted oil cooler with thermostatically controlled hydraulic motor driven fan/air to oil. System pressure test ports. Hoist Specifications (HP-19G) Main and Auxiliary Hoist Planetary reduction with automatic spring applied multi-disc wet brake. Electronic hoist drum rotation indicators and hoist drum cable followers. Maximum Single Line Pull: 1st layers:,2 lb. (9 185 kg) 3rd layer: 17, lb. (7 715 kg) 5th layer: 14,6 lb. (6 6 kg) Maximum Permissible Line Pull: 16, lb. (7 6 kg) with 6 x 37 class rope 16, lb. (7 6 kg) with 35 x 7 class rope Maximum Single Line Speed: 514 FPM (156 m/min) Rope Construction: 6x36 EIPS IWRC, Special Flexible 35 x 7 Flex-X, Rotation Resistant Rope Diameter: 3/4" (19 mm) Rope Length: Main Hoist: ft. (182.8 m) Auxiliary Hoist: ft. (182.8 m) Maximum Rope Stowage: 841 ft. (256 m) *Denotes optional equipment 3 5533 (supersedes 5489) 8 N6 218 HSL Link-Belt Cranes 2--2516 or 2-525-8 3
sales@reliablecraneservice.com 2-525-8 or 2--2516 specifications 4 Carrier FChassis Box section frame fabricated from high-strength, low alloy steel. Front/rear towing and tie down lugs. O Outrigger System Four hydraulic telescoping single-stage double box beam outriggers with inverted jacks and integral holding valves. Three position setting, %, % and fully extended. All steel fabricated, quick-release type round outrigger floats,.5 in. (775 mm) diameter. Maximum outrigger pad load: 125, lb. (56 kg). Outrigger Controls Controls and crane level indicator located in cab. Engine (Tier III) Cummins QSB 6.7L diesel, six cylinders, 275 bhp (5 kw) (Gross) @ 2, rpm. Maximum torque: 728 ft. lbs. (987 Nm) @ 1, RPM. Fuel Tank Capacity 72 gallons (273 L) Transmission Full rangeshift with 6 forward and 6 reverse speeds. Front axle disconnect for 4 x 2 travel. Electrical System Two 12-V maintenance free batteries. 12-V starting and lighting. Battery disconnect. CanBus Diagnostic system. Drive 4x4 Steering Fully independent power steering: Front: Full hydraulic, steering wheel controlled. Rear: Full hydraulic, switch controlled. Provides infinite variations of 4 main steering modes: front only, rear only, crab and coordinated. Rear steer indicator. Turning radius - 25 ft. Brakes Full hydraulic split circuit brakes operating on all wheels. Springapplied, hydraulically released parking brake mounted on front axle. Tires Std. 29.5 x 25-34 bias ply, General. L Lights Full lighting including turn indicators, head, tail, brake and hazard warning lights. Maximum Speed 22 MPH (35 kph). Gradeability (Theoretical) 75% (Based on 8,158 lb. [49 kg] GVW) 29.5 x 25 tires, 128 ft. (39. m) boom, plus 56 ft. (17. m) swingaway, 18, lb. (8 165 kg) counterweight, 75T hookblock and T headache ball). Miscellaneous Standard Equipment Full width steel fenders, full length aluminum decking, dual rear view mirrors, hookblock tiedown, electronic back-up alarm, light package, front stowage well, tachometer/hourmeter, rear wheel position indicator, 36, BTU hot water cab heater, hoist mirrors, engine distress A/V warning system, front/rear tie down and two lugs, coolant sight level indicator. *Optional Equipment *Auxiliary Lighting Package (includes cab mounted amber flashing light, hoist mounted work light, and dual base boom mounted floodlights.) *LMI light bar (in cab) *Air Conditioning (28, BTU) *3 degree NYC style mechanical swinglock *Rear Pintle hook *Cab controlled cross axle differential locks, (front and rear) *PAT data logger *Rubber mat for stowage trough *Denotes optional equipment Axles Front: Drive/steer with differential and planetary reduction hubs rigid-mounted to frame. Rear: Drive/steer with differential and planetary reduction hubs pivot-mounted to frame. Oscillation Lockouts Automatic full hydraulic lockouts on rear axle permits in. (25.4 cm) oscillation only with boom centered over the front. 5533 (supersedes 5489) 8 N6 218 HSL Link-Belt Cranes 2--2516 or 2-525-8 4
sales@reliablecraneservice.com 2-525-8 or 2--2516 dimensions 33 [131.] 5 7 [289] OUTSIDE TURN RADIUS (4WS) 42 [194] INSIDE TURN RADIUS (4WS) 139/9 [5.36] 3758 [147.96] 23 7 [19.97] 834 [32.83] 21 [197.68] 3688 [145.] 4216 [166.] 57 [81.] 8569 [337.36] 3835 [1.98] 2553 TRACK [.] 31 RETRACKED 124.2 5283 MID EXTEND [8.] 7315 FULL EXTEND [288.] Note: Reference dimensions in mm [inches] Weights GVW Front Rear Basic Machine lb. kg lb. kg lb. kg Basic Machine including 128 ft main boom, main and aux. hoist with ft of rope, 56' (17 m) bifold swingaway, full counterweight, T (9.1 mt) headache ball, and T (75 mt) hookblock: 8,158 49 53,888 24 444 54,2 24 617 Remove counterweight and aux. hoist. 56' (17 m) bifold. 87,917 39 879 63,5 28 813 24,397 11 66 Remove counterweight, aux. hoist, and 56' (17 m) bifold swingaway. 85,285 38 685 58,725 26 638 26,5 12 48 5533 (supersedes 5489) 8 N6 218 HSL Link-Belt Cranes 2--2516 or 2-525-8 5
sales@reliablecraneservice.com 2-525-8 or 2--2516 working range Working range diagram with bi-fold extension 6 2 2 56 ' EXT 1 1 1 33 ' EXT 1 Height From Ground in Feet 1 1 1 1 1 7 128 1 1 Boom and Extension Length in Feet 3 78 MAX BOOM ANGLE 1 1 1 1 1 1 1 1 1 Operating Radius in Feet From Axis of Rotation AXIS OF ROTATION 118.95 [9'-11"] Dimensions are for largest Grove furnished hookblock and overhaul ball, with anti-two block activated. THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE. The individual crane s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane. 5533 (supersedes 5489) 8 N6 218 HSL Link-Belt Cranes 2--2516 or 2-525-8 6
sales@reliablecraneservice.com 2-525-8 or 2--2516 load chart 41.3-128 ft. 18, lbs % 24' spread 3º 41.3-128 ft. 33-56 ft. 18, lbs % 24 ft. spread 3º Pounds Feet 41.3 ** 1 1 128 ++1, 124, 5, (71) (74.5) (77.5) +1, 124, 5, 59, 12 (72) (75.5) 1, 124, 4, 59, 42, *42, 15 (63) (68.5) (72.5) (75.5), 99,8 85, 59, 42, 42, *39,6 *31,9 (54.5) (71) (74) (76),5,2 72,5 57, 42, 42, 39,6 25 31,9 *25,7 *22, (44.5) (55) (66.5) () (73) (75) (77) 59, 58,1 57,8 49, 42, 39, 36,1 31,9 25,7 22, (31.5) (47) (56) (66) (69.5) (72) (74) (76) (77) 43,2 43, 42, 38,1 3 4, 31,3 29, 25,7 22, 35 (37.5) (49.5) (57) (62 ) (66) (68.5) (71.5) (73.5) (74.5) 33, 33, 32,9 33,7, 27, 25,6 23, 22, (24.5) (42.5) (52) (58) (65.5) (68.5) (71) (72.5) 26, 26, 27, 26,7 24, 22, 21,4,6 45 (34) (46) (53) (58.5) (65.5) (68) () See 21, 21,1 22,4 23,2 21,8,2 19, 18,3 Note 16 (22) (39.5) (48.5) (54.5) (59) (62.5) (65.5) 17,2 18,6 19, 19, 18, 17, 16, 55 (31.5) (43) () (55) (59.5) (63) (65) 14, 15, 16, 17, 16,4 15,4 14,7 (21) (37) (45.5) (51.5) (56) () (62.5) 13, 13,8 1 4, 5 14,9 14, 13,3 65 (29.5) (.5) (47.5) (53) (57) (59.5) 11, 11, 12,4 12, 12, 12,1 (19) (34.5) (43) (49.5) (54) (57),, 11, 11, 11, 75 (28) (38.5) (45.5) (51) (54) 8,5 9,1 9,6,1, (18) (33) (41.5) (47.5) (51) 7,8 8,3 8,8 9,1 85 (26.5) (37) (44) (48) 6,7 7,2 7, 8, (17.5) (32) () (44.5) 6, 6, 7, 95 (25.5) (35.5) (41) 5,3 5, 6,1 (17) (.5) (37) 5, 5,3 5 (25) (32.5) 4,2 4,6 1 (16.5) (27.5) 4, 115 (21.5) 3,4 1 (.5) Minimum boom angle (deg.) for indicated length (no load) 9 Maximum boom length (ft.) at deg. boom angle (no load) 1 #LMI operating code. Refer to LMI manual for instructions. *This capacity is based upon maximum obtainable boom angle. Note: ( ) Boom angles are in degrees. +9 parts line required to lift this capacity (using aux. boom nose). Refer to Operator's & Safety Handbook for reeving diagram. ++ parts line required to lift this capacity (using aux. boom nose). Refer to Operator's & Safety Handbook for reeving diagram. Lifting Capacities at Zero Degree Boom Angle Boom Angle 41.3 ** 1 1,7 15,1, 6, 5, 3, 2, 2, 1, (34.1) (42.8) (52.8) (63) (72.8) (82.8) (92.8) (2.8) (112.8) Note: ( ) Reference radii in feet. 1982 **This boom length is with inner-mid fully extended and outer-mid & fly fully retracted. Feet 35 45 55 65 75 85 95 5 1 115 1 125 1 135 1 145 1 155 1 165 Minimum boom angle ( ) for indicated length (no load) Maximum boom length (ft.) at boom angle (no load) Pounds 33 ft. LENGTH 56 ft. LENGTH #21 #22 #23 #41 #42 #43 11, 11, (77) 11, (75.5) 11, (73.5) 11, (71.5) 11, (69.5), 9,1 (65.5) 8,4 (63.5) 7,8 (61.5) 7,2 (59.5) 6,7 (57) 6,2 (55) 5,8 (52.5) 5,5 () 5,1 (47.5) 4,8 (45) 4,2 (42) 3,6 (39) 3, (36) 2,7 (32) 2,3 (28) 1,9 (23) 1,5 (16.5) *11,, (76.5) 9,7 (74.5) 9, (72.5) 8,3 (.5) 7,7 (68.5) 7,2 (66.5) 6,7 (64.5) 6,3 5,9 () 5,6 (57.5) 5,3 (55.5) 5, (53) 4,7 (.5) 4,5 (47.5) 4,2 (45) 3,9 (41.5) 3,4 (38.5) 2,9 (35) 2,4 (.5) *9,7 8,4 (77) 7,9 (75) 7,4 (73) 6,9 (71) 6,5 (69) 6,2 (66.5) 5,8 (64.5) 5,5 5,2 () 5, (57.5) 4,7 (55) 4,5 (52) 4,3 (49.5) 4,1 (46.5) 6, 6, (77.5) 6, (76) 6, (74.5) 6, (72.5) 6, (71) 6, (69.5) 6, 6, (66) 5,5 (64) 5,1 (62.5) 4,7 (.5) 4,4 (58.5) 4,1 (56.5) 3,8 (54.5) 3,5 (52.5) 3,3 (.5) 3,1 (48) 2,9 (46) 2,7 (43.5) 2,5 (41) 2,4 (38.5) 2, (35.5) 1,7 (32.5) 1,4 (29) 1,1 (24.5) *6, 5, (76.5) 5,7 (75) 5,3 (73) 4,9 (71.5) 4,6 (69.5) 4,3 4, (66) 3,8 (64) 3,6 3, () 3, (58) 3, (55.5) 2,8 (53.5) 2,6 (51) 2,5 (48.5) 2, (46) 2,2 (43.5) 2,1 (.5) 2, (37) 1,7 (33.5) *5, 4,6 (77) 4,3 (75.5) 4,1 (73.5) 3,8 (71.5) 3,6 (69.5) 3,4 3, (65.5) 3,1 (63.5) 2,9 (61) 2,8 (59) 2,6 (56.5) 2,5 (54) 2,4 (51.5) 2, (48.5) 15 28 44 23 31 46 1 1 NOTE: ( ) Boom angles are in degrees. #LMI operating code. Refer to LMI manual for operating instructions. *This capacity is based upon maximum boom angle. A6-829-3653 7 NOTES: 1. All capacities above the bold line are based on structural strength of boom extension and do not exceed 85% of tipping loads, in accordance with SAE J-765. 2. The 33 ft. extension length may be used with single or double part line lifting service. The 56 ft. extension length may be used for single line lifting service only. 3. For main boom lengths less than 128 ft. with the boom extension erected, the rated loads are determined by boom angle. Use only the column which corresponds to the boom extension length and offset for which the machine is set up. For boom angles not shown, use the rating of the next lower boom angle. 4. WARNING: Operation of this machine with heavier loads than the capacities listed is strictly prohibited. Machine tipping with boom extension occurs rapidly and without advance warning. 5. Boom angle is the angle above or below horizontal of the longitudinal axis of the boom base section after lifting rated load. 6. Capacities listed are with outriggers properly extended and vertical jacks set only. 7. When lifting over the main boom nose with 33 ft. or 56 ft. extension erected, the outriggers must be fully extended or % extended (17 ft. 4 in. spread). THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE. The individual crane s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane. 5533 (supersedes 5489) 8 N6 218 HSL Link-Belt Cranes 2--2516 or 2-525-8 7
sales@reliablecraneservice.com 2-525-8 or 2--2516 working range Working range diagram with bi-fold extension and one insert 8 2 2 o 76' EXT 1 1 1 1 1 Height from ground in feet 1 1 1 1 128 1 1 Boom and extension length in feet 41.3 78 MAX BOOM ANGLE 1 1 1 1 1 1 1 1 1 Operating radius in feet from axis of rotation AXIS OF ROTATION 118.95 [9'-11"] Dimensions are for largest Grove furnished hookblock and overhaul ball, with anti-two block activated. THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE. The individual crane s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane. 5533 (supersedes 5489) 8 N6 218 HSL Link-Belt Cranes 2--2516 or 2-525-8 8
sales@reliablecraneservice.com 2-525-8 or 2--2516 working range Working range diagram with bi-fold extension and two inserts 2 2 2 96' EXT 9 2 1 1 1 1 Height from ground in feet 1 1 1 1 1 128 1 1 Boom and extension length in feet 41.3 78 o MAX BOOM ANGLE 2 2 1 1 1 1 1 1 1 1 1 Operating radius in feet from axis of rotation AXIS OF ROTATION 118.95 [9'-11"] Dimensions are for largest Grove furnished hookblock and overhaul ball, with anti-two block activated. THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE. The individual crane s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane. 5533 (supersedes 5489) 8 N6 218 HSL Link-Belt Cranes 2--2516 or 2-525-8 9
sales@reliablecraneservice.com 2-525-8 or 2--2516 load chart 41.3-128 ft. ft. insert 18, lbs % 25 ft. spread Pounds 3º 76 ft. (56 ft. LENGTH + 1 INSERT) 96 ft. (56 ft. LENGTH + 2 INSERTS) Feet o o o o o o #84 #85 #86 #84 #85 #86 4,8 55 4,8 (77.5) 3,5 4,8 3,5 (76) (77.5) 65 4,8 *5,2 3,5 (74.5) (76.5) 4,8 (73) 4,8 (77.5) 3,5 (75) 75 4,8 4,4 3,5 3,7 (71.5) (76) (73.5) 4,7 4,1 *4, 3,5 3,4 () (74.5) (72.5) (76.5) 85 4,3 (68.5) 3,7 (73) 3, (76.5) 3, (71) 3, (75) *3,2 3,9 3, 3,2 2,9 2,8 2,7 (67) (71) (75) (69.5) (73.5) (77) 95 3,6 3,2 3, 2,6 2,5 2,4 (65.5) (69.5) (73) (68) (72) (75.5) 3,3 3, 2,8 2,3 2,3 2,2 (64) (68) (71.5) (66.5) (71) (74) 5 3, 2,7 (66) 2,6 (69.5) 2,1 (65) 2, (69.5) 2, (72) 1 2,7 2,5 2,4 1,9 1, 1,8 (.5) (64.5) (68) (63.5) (68) (.5) 115 2,5 2,3 2,2 1,7 1,7 1,7 (58.5) (62.5) (66) (66.5) (69) 1 2,3 (57) 2, (61) 2,1 (64) 1,5 (.5) 1,5 (64.5) 1,5 125 2,1 2, 1,9 1,3 1,3 1,3 (55) (59) (59) (63) (66) 1 1,9 1,8 1,8 1,1 1,2 1,2 (53) (57) () (57.5) (61.5) (64) 135 1,8 1,7 1, 1, 1, (51.5) (55) (58) (56) () 1,1 (62.5) 1 1,6 1,5 1,5 (49.5) (53) (56) 145 1,5 1,4 1,4 (47) (51) (53.5) 1 1, (45) 1,3 (49) 1,3 (51.5) 155 1,2 1,2 1,2 (43) (46.5) (48.5) 1 1,1 1,1 1,1 (.5) (44) (46) 165 1, (38) 1, (41.5) Minimum boom angle ( o) for indicated 36 44 54 58 length (no load) Maximum boom length (ft.) at o boom angle (no load) NOTE: ( ) Boom angles are in degrees. A6-829-3655 #LMI operating code. Refer to LMI manual for operating instructions. *This capacity is based upon maximum boom angle. RT875E - S/N 223983 NOTES: 1. All capacities above the bold line are based on structural strength of boom extension and do not exceed 85% of tipping loads, in accordance with SAE J-765. 2. The 56 ft. boom extension length may be used for single line lifting service only. 3. For main boom lengths less than 128 ft. with the boom extension erected, the rated loads are determined by boom angle. Use only the column which corresponds to the boom extension length and offset for which the machine is set up. For boom angles not shown, use rating of the next lower boom angle. 4. WARNING: Operation of this machine with heavier loads than the capacities listed is strictly prohibited. Machine tipping with boom extension occurs rapidly and without advance warning. 5. Boom angle is the angle above or below horizontal of the longitudinal axis of the boom base section after lifting rated load. 6. When lifting over the main boom nose with 56 ft. extension erected and inserts, the outriggers must be fully extended and vertical jacks set. 41.3- ft. 18, lbs Stationary 3º THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE. The individual crane s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane. Pounds Feet 41.3 * 12 49,,7 (72) 15 39,1 35, (63) (68.5) 24, (54.5) 24,3 22, 22, (71) 25 16, (44.5) 16, (55) 15, 15,9 (66.5) 15,8 () 11,2 11,2,9,6 11, 12,1 (31.5) (47) (56) (66) (69.5) 35 7, 7,6 7,2 8,4 8,8 (37.5) (49.5) (57) (66) 5,4 5,2 4,8 6, 6,3 (24.5) (42.5) (52) (58) 45 3,4 3,1 4,1 4,4 (34) (46) (53) (58.5) 1,3 (22) 1,7 (39.5) 2,6 (48.5) 3, (54.5) 55 1,3 (43) 1, () Minimum boom angle (deg.) for indicated length (no load) 21 38.5 42 49 Maximum boom length (ft.) at deg. boom angle (no load) #LMI operating code. Refer to LMI manual for instructions. Note: ( ) Boom angles are in degrees. *This boom length is with inner-mid fully extended and outer-mid & fly fully retracted. Lifting Capacities at Zero Degree Boom Angle Boom Angle 41.3 o 8,3 (34.1) Note: ( ) Reference radii in feet. 4, (42.8) #5 41.3-ft. 18, lbs Pick & Carry Up to 2.5 mph Pounds #6 3º A6-829-3649A Feet 41.3 * 12 59,4 49, (72) 15 49,6 (63) 49, (68.5) 38, (54.5) 37, 36,8 29,7 (71) 25, (44.5) 29, (55) 29, 29, (66.5) 24, (31.5) 23,7 (47) 23, (56) 23,8 24,4 (66) 35 18, (37.5) 17, (49.5) 18,1 (57) 19, 19, (66) 13,6 (24.5) 13, (42.5) 13,7 (52) 14, (58) 15, 45 9, (34) 9,2 (46) 11, (53) 12, (58.5) 7,4 (22) 7, (39.5) 8,2 (48.5) 8,9 (54.5) 55 5,4 (31.5) 6,5 (43) 7,2 () 3,9 (21) 5, (37) 5,7 (45.5) 65 3,8 (29.5) 4,4 (.5) 2,7 (19) 3,3 (34.5) 75 2,3 (28) 1,5 (18) Minimum boom angle (deg.) for indicated length (no load) Maximum boom length (ft.) at deg. boom angle (no load) #LMI operating code. Refer to LMI manual for instructions. Note: ( ) Boom angles are in degrees. Lifting Capacities at Zero Degree Boom Angle Boom Angle 41.3 * o 19, (34.1),2 (42.8) 6,4 (52.8) 3,1 (63) 2,1 (72.8) 1, (82.8) Note: ( ) Reference radii in feet. A6-829-36 *This boom length is with inner-mid fully extended and outer-mid & fly fully retracted. NOTES: 1. Capacities are in pounds and do not exceed 75% of tipping loads as determined by test in accordance with SAE J765. 2. Capacities are applicable to machines equipped with 29.6x25 (34 ply) General tires at 76 psi cold inflation pressure. 3. Capacities appearing above the bold line are based on structural strength and tipping should not be relied upon as a capacity limitation. 4. Capacities are applicable only with machine on firm level surface. 5. On rubber lifting with boom extensions not permitted. 6. For pick and carry operation, boom must be centered over front of machine, mechanical swing lock engaged and load restrained from swinging. When handling loads in the structural range with capacities close to maximum ratings, travel should be reduced to creep speeds. 7. Axle lockouts must be functioning when lifting on rubber. 8. All lifting depends on proper tire inflation, capacity and condition. Capacities must be reduced for lower tire inflation pressures. See lifting capacity chart for tire used. Damaged tires are hazardous to safe operation of crane. 9. Creep Not over ft. of movement in any minute period and not exceeding 1 mph. 5533 (supersedes 5489) 8 N6 218 HSL Link-Belt Cranes 2--2516 or 2-525-8
sales@reliablecraneservice.com 2-525-8 or 2--2516 load handling Weight Reductions for Load Handling Devices 33 FT.-56 FT. FOLDING BOOM EXTENSION *33 ft. Extension (Erected) - 3, lb. *56 ft. Extension (Erected) - 7,8 lb. *76 ft. (1 insert Erected) -,3 lb. *96 ft. (2 inserts Erected) - 13, lb. *Reduction of main boom capacities (no deduct required for stowed boom extension) When lifting over swingaway and/or jib combinations, deduct total weight of all load handling devices reeved over main boom nose directly from swingaway or jib capacity. AUXILIARY BOOM NOSE 136 lb HOOKBLOCK AND OVERHAUL BALL: USt, 5 Sheave 1,319 lb + USt, 3 Sheave 1, lb + USt, Overhaul Ball 568 lb + + Refer to rating plate for actual weight. NOTE: All load handling devices and boom attachments are considered part of the load and suitable allowances MUST BE MADE for their combined weights. Weights are for Grove furnished equipment. Line Pulls and Reeving Information Permissible Nominal Hoists Cable Specs Line Pulls Cable Length 3/4" (19 mm) 6x37 Class, Main EIPS, IWRC Special Flexible 16, lb. ft. Min. Breaking Str. 58, lb. 3/4" (19 mm) Flex-X 35 Main & Aux. Rotation Resistant (non-rotating) 16, lb. 7 ft. Min. Breaking Strength 85, lb. The approximate weight of 3/4" wire rope is 1.5 lb./ft. Boom Section vs. Section Extension Percentages 41.3 1 1 128 Boom sections: Percent Extension Inner-mid 65 Outer-mid 17 34 52 69 86 Fly 17 34 52 69 86 Hoist Performance Wire Hoist Line Pulls Drum Rope Rope Two Speed Hoist Capacity (ft.) Layer Low High 15 in. Drum Available lb.* Available lb.* Layer Total 1,2 9,6 1 1 2 18,4 8,7 1 211 3 17, 8, 1 331 4 15,7 7,4 129 4 5 14,6 6,9 139 599 *Max. lifting capacity: 6x37 or 35x7 class = 16, lb. Installation and Removal of Counterweight and Auxiliary Hoist Rated Lifting Capacities in Pounds on Outriggers Fully Extended 3 Radius LMI Code #1 in Main Boom Length Feet 41.3 ft.* 24, 12 24, 15 24, 24, 25 24, 24, *The boom must be fully retracted. 11 Working Area Diagram CENTERLINE OF BOOM 3o OVER SIDE CENTERLINE OF OUTRIGGER SUPPORT LONGITUDINAL CENTERLINE OF CRANE BOOM CENTERED OVER FRONT 3 o REAR AXLE OSCILLATION LOCKOUTS MUST BE SET TO MAINTAIN 3 o CAPACITIES CG OF LOAD OVER FRONT OVER REAR DIAGRAM FOR LIFTING ON OUTRIGGERS OVER SIDE SEE NOTE AT BOTTOM CENTERLINE OF ROTATION DIAGRAM FOR LIFTING ON TIRES THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE. The individual crane s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane. FRONT Bold lines determine the limiting position of any load for operation within working areas indicated. 5533 (supersedes 5489) 8 N6 218 HSL Link-Belt Cranes 2--2516 or 2-525-8 11
sales@reliablecraneservice.com 2-525-8 or 2--2516 Regional Headquarters Americas Manitowoc, Wisconsin, USA Tel: +1 9 684 6621 Fax: +1 9 683 6278 Shady Grove, Pennsylvania, USA Tel: +1 717 597 8121 Fax: +1 717 597 62 Europe, Middle East, Africa Ecully, France Tel: +33 472 18 Fax: +33 472 18 Asia Pacific Shanghai, China Tel: +86 21 51113579 Fax: +86 21 51113578 Singapore Tel: +65 6264 1188 Fax: +65 6862 4142 Regional Offices Americas Brazil Alphaville Tel: +55 11 33 Fax: +55 11 4688 13 Mexico Monterrey Tel: +52 81 8124 128 Fax: +52 81 8124 129 Europe, Middle East, Africa Algeria Hydra Tel: +21 3 21 48 1173 Fax: +21 3 21 48 1454 Czech Republic Netvorice Tel: +4 317 78 9313 Fax: +4 317 78 9314 France Baudemont Tel: +33 385 28 2589 Fax: +33 385 28 4 Cergy Tel: +33 1 31 31 Fax: +33 1 38 85 Decines Tel: +33 472 81 Fax: +33 472 81 Germany Langenfeld Tel: +49 21 73 89- Fax: +49 21 73 89 Hungary Budapest Tel: +36 13 39 8622 Fax: +36 13 39 8622 Italy Parabiago Tel: +3 331 49 3311 Fax: +3 331 49 33 Netherlands Breda Tel: +31 76 578 3999 Fax: +31 76 578 3978 Poland Warsaw Tel: +48 22 843 3824 Fax: +48 22 843 3471 Portugal Alfena Tel: +351 229 69 88 Fax: +351 229 69 8848 Lisbon Tel: +351 212 9 3 Fax: +351 212 9 349 Russia Moscow Tel: +7 495 641 2359 Fax: +7 495 641 2358 U.A.E. Dubai Tel: +971 43381 861 Fax: +971 4 3382 343 U. K. Middlesex Tel: +44 1 895 43 53 Fax: +44 1 895 45 Sunderland Tel: +44 191 522 Fax: +44 191 522 52 Asia Pacific Australia Melbourne Tel: +61 39336 1 Fax: +61 3 9 336 1322 Sydney Tel: +61 2 9 896 4433 Fax: +61 2 9 896 3122 China Beijing Tel: +86 58674761 Fax: +86 586747 Xi an Tel: +86 29 87891465 Fax: +86 29 878844 Korea Seoul Tel: +82 2 3439 Fax: +82 2 3439 5 Philippines Makati City Tel: +63 2 844 9437 Fax: +63 2 844 4712 Factories Brazil Alphaville China Zhangjiagang France Charlieu La Clayette Moulins Germany Wilhelmshaven India Calcutta Pune Italy Niella Tanaro Portugal Baltar Fânzeres Slovakia Saris U.S.A. Manitowoc Port Washington Shady Grove Constant improvement and engineering progress make it necessary that we reserve the right to make specification, equipment and price changes without notice. Illustrations shown may include optional equipment and accessories, and may not include all standard equipment. www.manitowoccranegroup.com 8 MANITOWOC Printed in USA Form No. PG Part No. 8-2 8 / 2M 5533 (supersedes 5489) 8 N6 218 HSL Link-Belt Cranes 2--2516 or 2-525-8 12