The line of Tyco Electronics radiation resistant/150 C pre-insulated terminals and splices includes terminals and splices of the well-known PIDG and PASTI-GRIP terminal designs. Radiation resistant terminals are made of fine grade, high conductivity copper with either bright tin-lead or matte tin-plating and feature polyvinylidene fluoride (PVF 2 ) insulation for high resistance to radiation and solvents. PIDG terminals meet the performance requirements of SAE-AS792. They are also tested by Tyco Electronics and an independent test facility and have fulfilled all requirements including radiation testing to 200 megarads and operating temperature range from -0 C to +150 C. One outstanding quality of the standard Tyco Electronics terminals, such as tapered entry ramps, help eliminate bent wire strands and insulation support for stronger, more reliable connections. Serrated or dimpled wire barrels provide maximum contact and tensile strength after crimping, and color coded insulation with wire size stamped on the terminal tongue identifies the product and assists in proper terminal-wire match. The radiation resistant/150 C terminals are designed and engineered to successfully withstand extreme vibration, shock and structural stresses, and other conditions which can adversely affect the critical circuit requirements in complex equipment. The matching Tyco Electronics tooling precisely crimps all terminations. This uniformity increases reliability and also serves as a built-in quality control factor.
Catalog 203 Ring Tongue Terminals PIDG Terminals - hisker Mitigating (Contains 3% Minimum ead Content in Plating) Terminal body : copper per ASTM-B152 with bright tin/lead (93/7) {3% MIN lead content} plating per ASTM-B55 Insulation support sleeve : copper per ASTM-B152 with bright tin/lead (93/7) {3% MIN lead content} plating per ASTM-B55 Insulation sleeve : PVF 2, natural with colored stripe 2-2 202-509 [.-.2] Tongue Thickness Maximun.029.7 ire Ins. Diameter Maximum.02 2.09 Stripe Color Stud Size 2 M2.203 5.1.203 5.1.35 Dimensions C 1 MIN..211 5.35.211 5.35.23.17.35 E.32 1.0.32 1.0. 1.7.71 17.05.702 17..73 1.70.73 1.70.792 20.12.1 20..1 21.7 oose Tape 5300-1 5301-1 5302-1 5303-1 530-1 2-20 320-1,290 [.1-.5].025..0 2.5 hite.35.31 1.03.77 19. 5309-2.21 5.5.21 5.5.15 3.9.15 3.9.50 1.23.50 1.23.72 17.02.72 17.07 5305-1 530-1.35.35.5 1.2.72 19.7 5307-1 5307-2 22-1 509-3,250 [.2-1.5]..125 3.1 1/ M 7.91.9 11.09.5 17..5 17..1 21.37. 21.. 21. 1.07 27.39 530-1 530-2 5309-1 53-1 53-2 Related Product Data Application tooling pages -11 Technical documents page 5/1 M 3/ 1/2.9.713 1.11.35.35 11.09.5 13..530 13..171.3.171.3.1 21.37.950 2.13.93 2.13.575 1.1.575 1.1 1.07 27.39 1.21 30.9 1.293 32.5.703 17..703 17. 5311-1 5312-1 5313-1 531-1 5315-1.5 17.. 21. 531-1 531-2 1-1 2,050-5,10 [1.0-2.2]..150 3.1 Blue 1/ M.9 11.09.5 17..5 17..1 21.37. 21.. 21. 1.07 27.39 5317-1 5317-2 531-1 531-2 5319-1 5/1 M.9 11.09.1 21.37 1.07 27.39 5320-1 3/ 1/2.713 1.11.5 13..530 13..950 2.13.93 23.73 1.21 30.9 1.293 32.5 5321-1 5322-1 1-Dimension applies from edge of metal wire barrel to center of stud hole. 2 USA: 1-00-522-752 Canada: 1-905-75-222 Mexico: 01-00-733-92
Catalog 203 Ring Tongue Terminals (continued) PIDG Terminals - hisker Mitigating (Contains 3% Minimum ead Content in Plating) Tongue Thickness Maximun ire Ins. Diameter Maximum Stripe Color Stud Size Dimensions C 1 MIN. E oose Tape 1-1 Heavy Duty 2,050-5,10 [1.0-2.2].050 1.3.230 5. Black 1/ M.33.71.33.71.33.71.219 5.5 11.09. 20.57.72 22.15.72 22.15.72 22.15 1.02 2.12.955 2.2 1.0 2.57 1.0 2.57 1.0 2.57 1.29 32.92 5393-1 539-1 5392-1 5393-1 539-1.219 5.5.375 9.53.35.302 7.7. 20.57.93 22.9.93 23.3 1.03 5593-1 5323-1.375 9.53.302 7.7.93 22.9 1.03 532-1 12-5,10-13,0 [2.2-.].02 1.07.230 5. 1/ M 5/1 M.375 9.53 13. 13..302 7.7. 11.. 11..93 22.9 1.05 2.7 1.05 2.7 1.03 1.322 33.5 1.322 33.5 5325-1 532-1 5327-1 3/ 1/2.593 15.0.715 1.1 13..7 12.0 1.115 2.33 1.05 2.77 1.1 35.92 1.1 35.92 532-1 5329-1 1-Dimension applies from edge of metal wire barrel to center of stud hole. Butt Splices PIDG Splices - hisker Mitigating (Contains 3% Minimum ead Content in Plating) Splice body : copper per ASTM-B152 with bright tin/lead (93/7) {3% MIN lead content} plating per ASTM-B55 Insulation support sleeve : copper per ASTM-B152 with bright tin/lead (93/7) {3% MIN lead content} plating per ASTM-B55 Insulation sleeve : PVF 2, natural with colored stripe 2-22 2-20 22-1 1-1 12-202- [.-.1] 320-1,290 [.1-.5] 509-3,250 [.2-1.5] 2,050-5,10 [1.0-2.2] 5,10-13,000 [2.2-.] Barrel I.D. Minimum.029.73.03 1.09.01 1.5.05 2.15.129 3.27 Stripe Color hite Blue ire Ins. Diameter Maximum.02 2.09.0 2.5.125 3.1.150 3.1.220 5.59 Dimension ength Maximum.90 22.1 1.035 2.29 1.25 32.1 1.25 32.1.220 2.07 oose Tape 535-1 - 5357-1 - 535-1 535-2 5359-1 - 53550-1 - Related Product Data Application tooling pages -11 Technical documents page USA: 1-00-522-752 Canada: 1-905-75-222 Mexico: 01-00-733-92 3
Catalog 203 Ring Tongue Terminals PASTI-GRIP Terminals - hisker Mitigating (Contains 3% Minimum ead Content in Plating) Terminal body : copper per ASTM-B152 with bright tin/lead (93/7) {3% MIN lead content} plating per ASTM-B55 Insulation sleeve : PVF 2, natural with colored stripe 13,0-20,00 [.-.5] Tongue Thickness Maximun.03 1.1 ire Ins. Diameter Maximum.30 9. Stripe Color Stud Size 1/ M 5/1 M 3/ 1/2 Max. asher Rad. 11.1 11.1.500 12.7.500 12.7.500 12.70.31.95.7 12.1.57 1.91.57 1.91.75 22.23 Dimensions E 1.3 3.13 1.3 3.1 1.02 35.2 1.0 35.72 1.0 35.72 1.52 39. 1.5 0.29 1.702 3.2 1.702 3.2 1..9 oose 5397-1 5393-1 597-1 539-1 5395-1 20,00-33,0 [.5-1.].0 1.22.3 11.0 Blue 1/ M 3/.21.7.21.7.515 13.09. 11.9.500 12.7.25 15. 1.2 37.5 1.22 1.2 1.591 0.2 1.719 3.7 1.9.2 1.905.2 53975-1 539-1 5397-1 Related Product Data Application tooling pages -11 Technical documents page 33,0-52,00 [1.-2.7].051 1.3.515 13.09 1/ M 3/ 1/2.5 13.7.5 13.7.5 13.7.79 17.25 1.72 2.7 1.72 2.7 1.72 2.7 1.72 2.7 1.9 9. 1.9 9. 2.01 51.1 2.01 51.1 5399-1 5390-1 53950-1 53951-1 2 52,00-3,700 [2.7-2.].00 1.53.50 1.23 1/ M 3/ 1/2.57 1.9.57 1.9.57 1.9.75 17.15.711 1.0.55 21.72 1.731 3.97 1.731 3.97 1.731 3.97 2.071 52.0 2.09 53.07 2.11 5.9 53977-1 53953-1 5395-1 USA: 1-00-522-752 Canada: 1-905-75-222 Mexico: 01-00-733-92
Catalog 203 ire Pins PIDG PVF 2 ire Pins - RoHS Compliant Terminal body : copper per ASTM-B152 with bright tin {99.5% MIN tin content} plating per ASTM-B55 Insulation support sleeve : copper per ASTM-B152 with bright tin {99.5% MIN tin content} plating per ASTM-B55 Insulation sleeve : PVF 2, natural with colored stripe Bright d 22-1 1-1 12-93-3,15 [.25-1.] 1,973-5,131 [1.0-2.0] 5,131-13,025 [2.-.] Tongue Thickness Maximun...02 1.07 ire Ins. Diameter Maximum.013 3.30.15 3.90.23.00 Stripe Color Blue.071 1.0.071 1.0.2 1.0 Dimensions X MIN..390 9.90.390 9.90.390 9.90.903 22.93.903 22.93 1.12 2.5 oose Tape 73709-1 737051-1 737053-1 ire Pins Matte d Terminal body : copper per ASTM-B152 with matte tin {99.5% MIN tin content} plating per ASTM-B55 Insulation support sleeve : copper per ASTM-B152 with matte tin {99.5% MIN tin content} plating per ASTM-B55 Insulation sleeve : PVF 2, natural with colored stripe 22-1 1-1 12-509-3,250 [.2-1.5] 3,20-5,10 [1.0-2.2] 5,10-13,0 [2.2-.] Tongue Thickness Maximun...01 1.0 ire Ins. Diameter Maximum.01 3.5.170.32.35 Stripe Color Blue.070 1.7.070 1.7.2 2.59 Dimensions X MIN..390 9.91.390 9.91.390 9.91.91 23.32.933 23.70 1.1 29.1 oose Tape 195191-1 195192-1 195193-1 X USA: 1-00-522-752 Canada: 1-905-75-222 Mexico: 01-00-733-92 5
Catalog 203 Ring Tongue Terminals PIDG PVF 2 Rings - RoHS Compliant Terminal body: copper per ASTM-B152 with matte tin {99.5% MIN tin content} plating per ASTM-B55 Insulation support sleeve : copper per ASTM-B152 with matte tin {99.5% MIN tin content} plating per ASTM-B55 Insulation sleeve : PVF 2, natural with colored stripe 2-2 2-20 202-509 [.-.2] 320-1,290 [.1-.5] Tongue Thickness Maximun.029.7.025. ire Insulation OD MAX.02 2.09.0 2.5 Stripe Color hite Stud Size 2 M2.203 5.1.203 5.1.35 Dimensions C 1 MIN.211 5.3.211 5.3.23.17.35.35.35 E MAX.32 1.05.32 1.05. 1.7.71 17.0.702 17.3.31 1.03.31 1.03.2 1.1.2 1.1 MAX.71 1.2.71 1.2.797 20.2.19 20.0. 22.00.779 19.79.779 19.79.2 20.9.2 20.9 oose Tape 920-1 920-2 920-3 920-5 920-921-1 921-3 921-2 921-921-5 921-7 921-921-.21 5.5.21 5.5.15.39.15 3.9.50 1.22.50 1.22.77 17.20.77 17.20 922-2 922-3.35.35.5 1.1.77 19.99 922- Related Product Data Application tooling pages -11 Technical documents page 22-1 509-3,250 [.2-1.5]..125 3.1 1/ M 5/1 M.9.9 11. 11..5 17.0.5 17.0.1 21.3.1 21.3.9 21.5.9 21.5 1.03 1.03 922-5 922-922-7 922-3/ 1/2.713 1.11.5 13.7.530 13..950 2.13.93 23.72 1.223 1.29 32.97 922-9 1-922-0.35.35.171.3.171.3.575 1.1.575 1.1.70 17.9.70 17.9 923-2 923-3.5 17.0.9 21.5 923-1-1 2,050-5,10 [1.0-2.2]..150 3.1 Blue 1/ M 5/1 M.9.9 11. 11..5 17.0.5 1.0.1 21.3.1 21.3.9 21.5.9 21.5 1.03 1.03 923-5 923-923-7 923-3/ 1/2.713 1.11.5 13.7.530 13..950 2.13.93 23.72 1.223 31.0 1.29 32.97 923-9 1-923-0 1-Dimension applies from edge of metal wire barrel to center of stud hole. USA: 1-00-522-752 Canada: 1-905-75-222 Mexico: 01-00-733-92
Catalog 203 Ring Tongue Terminals (continued) PIDG PVF 2 Rings - RoHS Compliant Tongue Thickness Maximun ire Insulation OD MAX Stripe Color Stud Size Dimensions C 1 MIN E MAX MAX oose Tape.33.71.219 5.59.15 20.70.77 22.2.90 2.3 1.051 2.70 930-2 930-.33.71.77 22.2 1.051 2.70 930-5 1-1 Heavy Duty 2,050-5,10 [1.0-2.2].050 1.27.230 5. 1/ M.33.71 11..77 22.2 1 2.2 1.051 2.70 1.301 33.05 930-930-7 5/1 M 11. 1 2.2 1.301 33.05 930-3/ 1/2.750 19.05 11..25 15. 1 2.2 1.221 31.01 1.301 33.05 1.599 0.1 930-9 1-930-0.375 9.53.375 9.53.302 7.7.302 7.7.93 22..93 22. 1.0 27. 1.0 27. 92-92-5 12-5,10-13,000 [2.2-.].01 1.0.230 5. 1/ M 5/1 M.375 9.53.302 7.7. 11.9. 11.9.93 22. 1.05 2.77 1.05 2.77 1.0 27. 1.327 33.71 1.327 33.71 92-92-7 92-3/ 1/2.593 15.0.715 1.1.7 12.0 1.115 2.77 1.05 2.77 1.19 3.0 1.19 3.0 332-9 1-92-0 1-Dimension applies from edge of metal wire barrel to center of stud hole. Butt Splices PIDG PVF2 Splices - RoHS Compliant Splice body: copper per ASTM-B152 with matte tin {99.5% MIN Tin content} plating per ASTM-B55 2-22 202- [.-.2] ire Insulation OD MAX.02 2.0 Stripe Color MAX.02 22.1 oose Tape 925-1 Insulation support sleeve : copper per ASTM-B152 with matte tin {99.5% MIN tin content} plating per ASTM-B55 2-20 22-1 320-1,290 [.1-.5] 509-3,250 [.2-1.5].0 2.5.125 3.1 hite 1.035 2.29 1.25 32.13 92-1 927-1 Insulation sleeve : PVF 2, natural with colored stripe 1-1 12-2,050-5,10 [1.0-2.2] 5,10-13,000 [2.2-.].150 3.1.220 5.59 Blue 1.25 32.13 1.5 2.0 92-1 929-1 Related Product Data Application tooling pages -11 Technical documents page USA: 1-00-522-752 Canada: 1-905-75-222 Mexico: 01-00-733-92 7
Catalog 203 PIDG PVF 2 ire Pins Application Tooling oose form terminal and splice tooling for wire range 2- [0.12-.0 mm2] Technical Documents Instruction Sheets : 0-1559 CERTI-CRIMP hand crimp tools 0-172 crimping dies for -2/0 connectors Hand Tools mm 2 Style Part Number 2-20.1-.5 2-22.1-. 2-2 & 22-1.1-.2 &.2-1.5 DAHT 7907-1 T-HEAD Tool 59275 T-HEAD Tool 59300 DAHT 121 T-HEAD Tool 59275 DAHT 73 T-HEAD Tool 59250 T-HEAD Tool 59300 22-1.2-1.5 DAHT 9151-1 1-1 1.0-2.2 DAHT 737 T-HEAD Tool 59250 1-1 HD 1.0-2.2 Heavy Head 59239-12- 2.2-. Heavy Head 59239- CERTI-CRIMP Hand Tools DAHT Heavy Head Hand Tool T-HEAD Tool Battery Crimp Tool Kit Take automatic crimping away from the bench to the product, with this convenient, portable, battery operated tool. It s at home in the factory or in the field. It performs approximately 0 crimps per charge. Request catalog 177331 for more information. 2 Pneumatic Tool System This versatile system provides the ultimate in wire range flexibility for higher volume operation. It s available with hand-or-foot operated configurations. Request catalog 1220 for more information. USA: 1-00-522-752 Canada: 1-905-75-222 Mexico: 01-00-733-92
Catalog 203 Tooling for loose form terminals, wire range -2 [.-2. mm2] Ordering Information: To insure that all applicable Tyco Electronics part numbers are specified in your order we recommend that you make note of the following information: 1. Select either Electric Hydraulic Tool 10700-1, -2, Foot Operated Tool 15359-1 or Hand Pump 1531-1. 2. Powered systems require a pump, hand or foot control, hose, crimp head and die. 3. The portable battery pump, 10111-1, includes a hand control. Manual systems require hand tools and the battery hand tool requires only dies. 5. Refer to matrix for die, head and hand tool options. Application Tooling (continued) Tyco Electronics continues the quality tradition of AMP crimping tools with a new line of industry-standard,000 psi (,950 kpa) hydraulic compression crimp heads, pumps and interchangeable U-dies. A new battery-powered pump and tool options provide unprecedented portability for any crimping application. Electric/Hydraulic Power Unit : [.-2. mm2]. Heads and dies are listed in the table below. : Power Unit Only (Includes pressure release on unit) 115 Volts 0 Hz 10700-1 (,000 psi) 230 Volts 0 Hz 10700-2 (,000 psi) Portable, Battery/Hydraulic Power Unit (Kit includes Hand Controller,,000 psi) 10111-1 Hydraulic Hand Tool 19079-1 is also available Crimping Heads, Hand Tools or Dies ire Size in (mm 2 ) Hydraulic Crimping Tooling,000 psi Operating Pressure Hand-Tool Hydraulic Head Hydraulic Heads 19079-1 1907-1, 197230-1 175277-1 175277-1 U-Dies U-Dies Shank Dies [7-.5] 19079-1 1907-1, 197230-1 175277-1 175277-1 [13-15] 19053-1 19053-1 5-1 5-1 [21] 190535-1 19053-1 0-1 0-1 2 [3-35] 190-1 190-1 1-1 1-1 Accessory Power Controls and Hoses Control and hose accessories must be ordered separately. If electric hydraulic tool is to be used in portable applications, a handle control and hose assembly should be used. For stationary applications, a foot switch assembly and hose assembly will be necessary. Multidirectional valves are used when more than one crimping head is permanently attached to the tool. Accessories For use with Power Unit No. 10700-1 10700-2 10700-1 10700-2 Accessory Description Accessory Part Number 7 ft. [2.13 m] handle control assembly - hose and cord 1901775-1 15 ft. [.57 m] handle control assembly - hose and cord 190177-1 21 ft. [. m] handle control assembly - hose and cord 1901777-1 Remarks 15 ft. [.57] foot switch assembly 2-1 need hose assembly ft. [0.91 m] hose assembly 1532-1 2-1 foot switch ft. [2.13 m] hose assembly 1532-2 assembly needed 20 ft. [.57 m] hose assembly 1532-3 with hose 3-way multi-directional valve (manual) 190172-1 USA: 1-00-522-752 Canada: 1-905-75-222 Mexico: 01-00-733-92 9
Catalog 203 DYNA-CRIMP Tooling for loose form terminals. ire range -2/0 [7-70 mm2] Ordering Information: To insure that all applicable AMP part numbers are specified in your order, we recommend that you make your selection in four () steps: 1. Select either Electric Hydraulic Tool 9120. Foot Operated Tool 9325-3 or Hand Tool 5997-1. 2. Select a head if using either the Electric Hydraulic or Foot Operated Tools. 3. Select dies from the table on this page.. Select control and hose mechanism from accessories list below when using 9120. Application Tooling (continued) Electric/Hydraulic Power Unit : This unit provides crimping for terminals in the wire range of -2/0 [7-70 mm 2 ]. Heads and dies are listed in the table below. : Power Unit Only (Includes pressure release on unit) 115 Volts 0 Hz : 9120 230 Volts 0 Hz : 9120-2 Crimping Heads and Dies for Tools 9120-1, 9325-3 and 5997-1 mm 2 Dies for Head 90 7-5-1 PASTI-GRIP Style Terminals Dies for Head 9051 and 5997-1 752-1 720* 1-15 59-1 21 0-1 753-1* 721* 75-1 722* *No insulation crimp. **arge expansion. 2 3-35 1-1 7239-1** 755-1 723* Accessory Power Controls and Hoses Control and hose accessories must be ordered separately. If electric hydraulic tool is to be used in portable applications, a handle control and hose assembly should be used. For stationary applications, a foot switch assembly and hose assembly will be necessary. Multidirectional valves are used when more than one crimping head is permanently attached to the tool. Accessories For use with Power Unit No. 9120-1 9120-2 9120-1 9120-2 Accessory Description Accessory Part Number 7 ft. [2.13 m] handle control assembly - hose and cord 59907-7 15 ft. [.57 m] handle control assembly - hose and cord 1-59907-5 15 ft. [.57 m] handle control assembly - cord (less hose) 1-5990-5 21 ft. [. m] handle control assembly - hose and cord 2-59907-1 21 ft. [. m] handle control assembly - cord (less hose) 2-5990-1 2 ft. [.53 m] handle control assembly - hose and cord 2-59907- Remarks 15 ft. [.57] foot switch assembly 2-1 need hose assembly 3 ft. [0.91 m] hose assembly 59909-3 2-1 foot switch 7 ft. [2.13 m] hose assembly 59909-7 assembly needed 15 ft. [.57 m] hose assembly 1-59909-5 with these hose 21 ft. [. m] hose assembly 2-59909-1 assemblies 3-way multi-directional valve 59220 -way multi-directional valve 59221 foot switch only USA: 1-00-522-752 Canada: 1-905-75-222 Mexico: 01-00-733-92
Catalog 203 Hydraulic Hand Tool for -2 [7-35 mm2] Application Tooling (continued) Hydraulic Hand Tool Part No. 19079-1 Dies for this tool are listed in the table on page 9. Hydraulic Hand Tool Part No. 5997-1 Dies for this tool are listed in the table on page under head No. 9051. Tape Form Terminal and Splice Tooling for 2- [0.2- mm2] Model G Terminating Machine Part No. 35500-1 Applicator : 57200-3 TAPETRONIC Machine Part No. 975 Requires dies. No applicator required. Tyco Electonics application tools are designed to produce a carefully controlled, uniform pressure crimp, whether manually or pneumatically powered. All tools feature matching dies that fully bottom at the completion of the crimp, resulting in a proper crimp height. These dies are color coded to aid in matching tool to wire size. Dies for Tape Mounted Terminals mm 2 Dies 22-1 0.3-1. 972 1-1 1.25-2.0 973 12-3.0 -.0 97 For AMP-O-ECTRIC Machine 5535-5, use aplicator 57200-2 USA: 1-00-522-752 Canada: 1-905-75-222 Mexico: 01-00-733-92 11
Catalog 203 Part Number Index Part No. Page RoHS Part No. Page RoHS Part No. Page RoHS 5300-1 2 5309-2 2 922-9 R 5301-1 2 5393-1 1-922-0 R 5302-1 2 539-1 923-2 R 5303-1 2 5395-1 923-3 R 530-1 2 539-1 923- R 5305-1 2 5397-1 923-5 R 530-1 2 5399-1 923- R 5307-1 2 53950-1 923-7 R 5307-2 2 53951-1 923- R 530-1 2 53953-1 923-9 R 530-2 2 5395-1 1-923-0 R 5309-1 2 5393-1 3 92-7 R 53-1 2 539-1 3 92-5 7 R 53-2 2 53975-1 92-7 R 5311-1 2 53977-1 92-7 7 R 5312-1 2 5397-1 92-7 R 5313-1 2 5390-1 92-9 7 R 531-1 2 5392-1 3 1-92-0 7 R 5315-1 2 5393-1 3 925-1 7 R 531-1 2 539-1 3 92-1 7 R 531-2 2 5593-1 3 927-1 7 R 5317-1 2 597-1 92-1 7 R 5317-2 2 920-1 R 929-1 7 R 531-1 2 920-2 R 930-2 7 R 531-2 2 920-3 R 930-7 R 5319-1 2 920-5 R 930-5 7 R 5320-1 2 920- R 930-7 R 5321-1 2 921-1 R 930-7 7 R 5322-1 2 921-2 R 930-7 R 5323-1 3 921-3 R 930-9 7 R 532-1 3 921- R 1-930-0 7 R 5325-1 3 921-5 R 73709-1 5 R 532-1 3 921- R 737051-1 5 R 5327-1 3 921-7 R 737053-1 5 R 532-1 3 921- R 195191-1 5 R 5329-1 3 922-2 R 195192-1 5 R 535-1 3 922-3 R 195193-1 5 R 5357-1 3 922- R 535-1 3 922-5 R 535-2 3 922- R 5359-1 3 922-7 R 53550-1 3 922- R 12 USA: 1-00-522-752 Canada: 1-905-75-222 Mexico: 01-00-733-92
Global Contacts Americas Argentina (Buenos Aires) Phone: +5-11-733-2200 Fax: +5-11-733-2211 Brasil (São Paulo) Phone: +55-11-23-000 Fax: +55-11-23-030 Chile (Santiago) Phone: +5-2-35-031 Fax: +5-2-223-177 Canada (Toronto) Phone: +905-75-222 Fax: +905-7-5520 Phone: +905-70-25 Fax: +905-7-5525 Colombia (Bogota) Phone: +57-1-319-959 Fax: +57-1-319-90 Mexico (Mexico City) Phone: +52-55-1-000 +01-00-733-92 Fax: +52-55-1-0901 For atin/south American (Countries not shown) Phone: +5-11-733-2015 Fax: +5-11-733-203 United States (Harrisburg, PA) Phone: +1-717-5-00 Fax: +1-717-9-7575 Phone: +1-00-522-752 Fax: +1-717-9-7575 (Troy, MI) Phone: +1-2-273-3359 Fax: +1-2-273-3322 Asia/Pacific Australia (Sydney) Phone: +1-2-955-200 Fax: +1-2-9502-255 Phone: +1-2-90-200 Fax: +1-2-93-1 India (Bangalore) Phone: +91-0-25-000 Fax: +91-0-25-020 Indonesia (Jakarta) Phone: +5-2-0311 Fax: +5-2-12 Japan (Kawasaki, Kanagawa) Phone: +1---111 Fax: +1--12-3207 Phone: +1---013 Fax: +1--12-3200 Korea (Seoul) Phone: +2-2-315-500 Fax: +2-2-3-3 Malaysia (Selangor) Phone: +0-3-705-3055 Fax: +0-3-705-30 New Zealand (Auckland) Phone: +-9-3-50 Fax: +-9-3-5 Philippines (Makati City) Phone: +32--0171 Fax: +32-7-1 People s Republic of China (Hong Kong) Phone: +52-2735-12 Fax: +52-2735-023 (Shanghai) Phone: +-21-207-15 Fax: +-21-207-1599 Singapore (Singapore) Phone: +5-2-0311 Fax: +5-2-12 Taiwan (Taipei) Phone: +-2-7-27 Fax: +-2-7-22 Thailand (Bangkok) Phone: +-2-955-0500 Fax: +-2-955-0505 Vietnam (Ho Chi Minh City) Phone: +--930-55 Fax: +--930-33 Europe/Middle East/Africa Austria (Vienna) Phone: +3-1-905-0-0 Fax: +3-1-905-0-1333 Phone: +3-1-905-0-129 Fax: +3-1-905-0-1251 Belarus (Minsk) Phone: +375 17 237 7 9 Fax: +375 17 237 7 9 Belgium (Kessel-o) Phone: +32-1-352-300 Fax: +32-1-352-355 Bulgaria (Sofia) Phone: +359-2-971-2152 Fax: +359-2-971-2153 Czech Republic and Slovakia Czech Republic (Kurim) Phone: +20-51-12-111 Fax: +20-51-12-223 Phone: +20-51-12-113 Fax: +20-51-12-132 Denmark (Glostrup) Phone: +5-3--0-00 Fax: +5-3--1-1 Egypt (Cairo) Phone: +202-19-233 Fax: +202-17-77 Estonia (Tartu) Phone: +372-513-27 Fax: +372-700-779 Finland (Helsinki) Phone: +35-95-12-3-20 Fax: +35-95-12-3-250 France (Cergy-Pontoise Cedex) Phone: +33-1-320- Fax: +33-1-320-00 Phone: +33-1-320- Fax: +33-1-320-23 France Export Divisions (Cergy-Pontoise Cedex) Phone: +33-1-320-0 Fax: +33-1-320-99 Germany (Bensheim) Phone: +9-251-133-0 Fax: +9-251-133-0 Phone: +9-251-133-1999 Fax: +9-251-133-19 Greece (Athens) Phone: +30-2-9370-39/397 Fax: +30-2-9370-55 Hungary (Budapest) Phone: +3-1-29-00 Fax: +3-1-29- Phone: +3-1-29-1 Fax: +3-1-29-17 Ireland (Dublin) Phone: +353-1--512 Fax: +353-1--571 Israel (Petach-Tikva) Phone: +972-3-929-0999 Fax: +972-3-919- Italy (Collegno (Torino)) Phone: +39-011-012-111 Fax: +39-011-031-11 Phone: +39-011-012-2 Fax: +39-011-0-27-2 ithuania and atvia ithuania (Vilnius) Phone: +370-5-213-102 Fax: +370-5-213-103 Phone: +370-5-211-301 Fax: +370-5-213-103 Netherlands ( s-hertogenbosch) Phone: +31-73-2-2 Fax: +31-73-212-35 Phone: +31-73-2-999 Fax: +31-73-2-99 Norway (Nesbru) Phone: +7--77--50 Fax: +7--77--55 Poland (arsaw) Phone: +-22-57-700 Fax: +-22-57-720 Phone: +-22-57-70 Fax: +-22-57-720 Romania (Bucharest) Phone: +0-21-311-379/359 Fax: +0-21-312-057 Russia (Moscow) Phone: +7-95-790-7902 Fax: +7-95-721-193 Phone: +7-95-790-7902-0 Fax: +7-95-790-7902-01 Russia (St. Petersburg) Phone: +7-12-71-192 Fax: +7-12-71-193 Slovenia (jubljana) Phone: +3-151-3270 Fax: +3-151-320 USA: 1-00-522-752 Canada: 1-905-75-222 Mexico: 01-00-733-92 South Africa (Port Elizabeth) Phone: +27-1-503-500 Fax: +27-1-51-00 Spain (Barcelona) Phone: +3-93-291-0330 Fax: +3-93-201-779 Sweden (Upplands Väsby) Phone: +--50-72-50-00 Fax: +--50-72-50-01 Switzerland (Steinach) Phone: +1-71-7-07 Fax: +1-71-7-0 Turkey (Istanbul) Phone: +90-212-21-11/2/3 +90-212-22-5130/530 Fax: +90-212-21-1 Ukraine (Kiev) Phone: +30--20-225 Fax: +30--20-22 Phone: +30--20-225 Fax: +30--20-22 United Kingdom (Stanmore, Middlesex) Phone: +-70-0020 Fax: +-20-95-23 Freephone (UK only): +000-27- Phone: +-70-0020 Fax: +-20-20-095 13
Tyco Electronics Corporation Harrisburg, PA 2009 Tyco Electronics Corporation. All Rights Reserved. 203 CIS PDF 7/2009 AMP, CERTI-CRIMP, PIDG, PASTI-GRIP, T-HEAD, TE logo and Tyco Electronics are trademarks. Other products, logos and company names mentioned herein may be trademarks of their respective owners. hile Tyco Electronics has made every reasonable effort to ensure the accuracy of the information in this catalog, Tyco Electronics does not guarantee that it is error-free, nor does Tyco Electronics make any other representation, warranty or guarantee that the information is accurate, correct, reliable or current. Tyco Electronics reserves the right to make any adjustments to the information contained herein at any time without notice. Tyco Electronics expressly disclaims all implied warranties regarding the information contained herein, including, but not limited to, any implied warranties of merchantability or fitness for a particular purpose. The dimensions in this catalog are for reference purposes only and are subject to change without notice. Specifications are subject to change without notice. Consult Tyco Electronics for the latest dimensions and design specifications.