Important: Please read these instructions carefully prior to installation. Please refer to your fitting instruction to ensure that the roof racks are installed in the correct locations. Check the contents of kit before commencing fitment and report any discrepancies. Place these instructions in the vehicle s glove box after installation is complete. Layout Important Information Maximum Load Rating 75kg. Recommendations It is essential that all bolt connections be checked after driving a short distance when you first install your Rhino Tourmaster lloy Tray. olt connections should be checked again at regular intervals (probably once a week is enough, depending on road conditions, usage, loads and distances travelled). You should also check the roof bars each time they are refitted.make sure to fasten your load securely. Please ensure that all loads are evenly distributed and that the centre of gravity is kept as low as possible. Use only non-stretch fastening ropes or straps. Sensitivity to Crosswinds, ehaviour in Curves and raking The handling characteristics of the vehicle, changes when you transport a load on the roof. For safety reasons, we recommend you exercise extreme care when transporting wind-resisting loads; special consideration must be taken into account when braking. Please remove alloy tray and crossbars when putting vehicle through an automatic car wash. Load Ratings Maximum permissible load is 75kg (include the weight of the alloy tray and roof bars, 7kg). When roof racks are to be used in off-road conditions, please build a safety factor of 1.5 into this load limit. lthough the roof racks are tested and approved to S1235-2000, ustralian road conditions can be much more rigorous. Note for Dealers and Fitters It is your responsibility to ensure instructions are given to the end user or client Rhino-Rack 3 Pike Street, Rydalmere, NSW 2116, ustralia. Document No: RR196 (Ph) (02) 9638 4744 Prepared y: ndy Wana Issue No: 01 (Fax) (02) 9638 4822 uthorised y: Geoff Cropley Issue Date: 14/11/2008 These instructions remain the property of Rhino-Rack ustralia Pty Ltd and may not be used or changed for any other purpose than intended.
Parts List SMLL (RTT1) Item Component Name Qty Part No 1 Side Moulding 2 M417 2 Intermediate ar (Drilled) 2 451 3 Intermediate ar (Undrilled) 5 448 4 Front/Rear ar 2 454 5 Main Cross ar 2 445 6 Wind Deflector 1 C704 MEDIUM (RTT2) Item Component Name Qty Part No 1 Side Moulding 2 M417 2 Intermediate ar (Drilled) 2 452 3 Intermediate ar (Undrilled) 5 449 4 Front/Rear ar 2 455 5 Main Cross ar 2 446 6 Wind Deflector 1 C705 LRGE (RTT3) Item Component Name Qty Part No 1 Side Moulding 2 M417 2 Intermediate ar (Drilled) 2 453 3 Intermediate ar (Undrilled) 5 450 4 Front/Rear ar 2 456 5 Main Cross ar 2 447 6 Wind Deflector 1 C706 HRDWRE KIT Maximum carrying capacity: 75kg 7 M6 X 27 utton Security 8 063 8 M6 Spring Washers 8 W004 9 M6 Standard Hex Nut 8 N022 10 Top Clamp 4 M419 11 ottom Clamp 4 M420 12 earer End Cap 4 M418 13 12mm Self tapping screws 12 171 14 Security Key Short 1 SecKey-S 15 Fitting Instructions 1 RR196 Tools Required: Tape measure, Marking pen, Philips head screwdriver, 4 5 6 Detail Detail 1 2 3 7 8 9 10 11 12 13 14 Care Instruction: Wash and clean vehicle roof rails prior to fitment 1 ssemble the Rhino 2500 Series without the crossbars as shown Fitting Instruction 2500 Series SX (suits aero bar profile) OR ssemble the SX Sportz Rail ar without the crossbars as shown Replace supplied Sportz bars with Main Cross ars (item 5) Replace supplied Sportz bars with Main Cross ars (item 5)
2 Insert Main Cross ar into the leg as shown. Set aside for assembly later. Supplied with 2500 kit Supplied with SX kit (to suit aero bar profile) 2500 Series SX (suits aero bar profile) 3 Prepare to assemble the tray D C C Intermediate bar (Drilled) Intermediate bar (Undrilled) C Front / Rear bar D Side moulding D
4 Steps 1-8 : Screw in the self tapping screws (item 16) as shown 2 3 4 1 6 7 8 5 5 Step 9 : Peel off the VH tape on the deflector Steps 10-11 : lign the Wind Deflector with the crossbar holes (10) and (11), insert self tapping screws. Steps 12-13 : Insert self tapping screws. 12 13 10 9 11
6a Place the completed tray on top of the 2500 Series crossbar assembly. For 2500 Series crossbar spacing, refer to inset picture below. DETIL Refer to dimension and (as shown) on your particular vehicle s supplied fitting instructions (DK kit) for crossbar spacing. FRONT RER
6b Place the completed tray on top of the SX crossbar assembly. For SX crossbar spacing Distance measured from bar centre to bar centre Min : 600mm Max : 850mm DETIL MIN 600 mm MX 850 mm Distance measured from bar centre to bar centre
7a ssemble the clamp on the Tourmaster Crossbar as shown. 7b ssemble the clamp on the SX Tourmaster Crossbar as shown. 8 The Rhino Tourmaster lloy Tray is ready for use.