ine Storage Design Guide
Contents 3 ine Storage 4 Specifications 12 Custom Panels 24 Full-Scale Templates 32 arranty Features and specifications are subject to change at any time without notice. Visit subzero.com/specs for the most up-to-date information. IMPORTNT NOTE: Throughout this guide, dimensions may vary by ± 1 /8" (3). Dimensions in parentheses are millimeters unless otherwise specified. Model 427G.
INE STORGE ine Storage ine finds a well-deserved place of honor in a Sub-Zero wine storage unit. Every detail is designed to ensure better wine preservation. Cherrywood-faced shelves, soft lighting, custom cabinetry if desired Sub-Zero helps make a wine collection an element of beauty in the home. KEY FETURES Integrated, overlay, flush inset and stainless steel design options. Full-view glass door standard on all models. Freestanding model 424FSG does not require panels or surrounding cabinetry. Discreet interior lighting with illuminated display shelf for prized bottles of wine. Two independent storage zones maintain temperature, humidity and UV protection. Roller-assembly wine shelves with natural cherrywood facing have three-quarter extension for easy access. ine shelves accommodate 750 ml bottles, half-bottles and magnums. INE STORGE MODELS 315 424G 424FSG 427G 427RG S-30 subzero.com/specs 3
INE STORGE Overall Dimensions MODEL 315 MODEL 424G 15 1 /8" (384) 24" (610) 23 7 /8" (606) 24" (610) 34 1 /16" (865) 34" (864) 4" (102) 4" (102) 16 5 /8" (422) 25 3 /8" (645) 1 3 /4" (44) 1 3 /4" (44) SPECIFICTIONS STORGE CPCITY BOTTLES (750 ML) 315 26 424G 46 424FSG 46 Overall dimensions are based on stainless steel panels and handles. Refer to page 13 for door clearance information. SHIPPING EIGHT LB (KG) 315 118 (54) 424G 195 (88) 424FSG 220 (100) 4 Sub-Zero Customer Care 800.222.7820
INE STORGE Overall Dimensions MODEL 424FSG Opening Dimensions MODELS 315 ND 424G 24 1 /4" (616) 24 5 /8" (625) 24" (610) OPENING DEPTH 34 3 /16" (868) TOP VIE 4" (102) 34 1 /2" (876) OPENING HEIGHT OPENING IDTH 25 3 /8" (645) SIDE VIE FRONT VIE 1 3 /4" (44) OPENING IDTH MODEL 315 15 1 /4" (387) 424G 24" (610) Freestanding model 424FSG has a finished stainless steel exterior and handles. subzero.com/specs 5
INE STORGE Overall Dimensions MODEL 427G MODEL 427RG 27" (686) 24" (610) 27" (686) 24" (610) 14" (356) 14" (356) 13 /16" (21) 13 /16" (21) 78 9 /16" (1995) 78 9 /16" (1995) 80" (2032) OPENING HEIGHT 3 /8" (10) 80" (2032) OPENING HEIGHT 1 /2" (13) 13 1 /4" (337) 8 15 /16" (227) 20 3 /8" (518) 10 1 /4" (260) 34 1 /2" (876) 9 3 /4" (248) HEIGHT DIMENSIONS ± 1 /2" (13) 4" (102) HEIGHT DIMENSIONS ± 1 /2" (13) 4" (102) 24" (610) 24" (610) 4 5 /8" (117) 4 5 /8" (117) 25 1 /2" (648) 19 1 /2" (495) 25 1 /2" (648) SPECIFICTIONS STORGE CPCITY R CU FT (L) BOTTLES (750 ML) 427G 132 427RG 5.3 (150) 78 Overall dimensions do not include panels or handles. Dimensions will vary with panel thickness. SHIPPING EIGHT LB (KG) 427G 395 (179) 427RG 410 (186) 6 Sub-Zero Customer Care 800.222.7820
INE STORGE Opening Dimensions MODELS 427G ND 427RG TOP VIE 25" (635) OPENING DEPTH OPENING DIMENSIONS MODEL H 427G 27" (686) 80" (2032) 427RG 27" (686) 80" (2032) The depth of each integrated model is 24" (610). llow for panel thickness when planning the finished opening depth. H OPENING HEIGHT OPENING IDTH DUL INSTLLTION hen installing two integrated units (models 427G and 427RG) side by side in a dual installation, the opening width is the width of the two units added together. dual installation kit will be required for this installation. If a dual installation kit is not specified, a minimum 2" (51) filler strip is required between units. Dual installation kits are available through an authorized Sub-Zero dealer. For local dealer information, visit the find a showroom section of our website, subzero.com. For questions regarding the installation, call Sub Zero customer care at 800-222-7820. SIDE VIE FRONT VIE subzero.com/specs 7
INE STORGE Overall Dimensions MODEL S-30 Opening Dimensions MODEL S-30 STNDRD INSTLLTION 30" (762) 26 3 /16" (665) 24" (610) OPENING DEPTH 84" (2134) TOP VIE 73 3 /4" (1873) HEIGHT DIMENSIONS ± 1 /2" (13) 4" (102) 23 7 /8" (606) 83 3 /4" (2127) OPENING HEIGHT OPENING IDTH 23 7 /8" (606) 17" (432) 31 1 /4" (796) SIDE VIE FRONT VIE NOTE: Shaded line represents profile of unit. 2 3 /8" (60) SPECIFICTIONS STORGE CPCITY BOTTLES (750 ML) S-30 147 SHIPPING EIGHT LB (KG) S-30 445 (202) Overall dimensions are based on the stainless steel model. For flush inset applications, add 1 /2" (13) to door clearance dimensions. OPENING IDTH MODEL S-30 29 1 /2" (749) If an 83" (2108) grille height is specified, the opening height must be decreased by 7 /8" (22). If an 88" (2235) grille height is specified, the opening height must be increased by 4" (102). If two units are installed side by side, refer to page 10 for dual standard installations. 8 Sub-Zero Customer Care 800.222.7820
INE STORGE Opening Dimensions MODEL S-30 FLUSH INSET INSTLLTION 26 3 /16" (665) FLUSH INSET DEPTH 2 3 /16" (56) FINISHED CLETS* TOP VIE 1 /4" (6) 1 1 /4" (32) 84" (2134) FLUSH INSET HEIGHT FLUSH INSET IDTH 1 1 /4" (32) 4" (102) 3" (76)* TYPICL 2 3 /16" (56) SIDE VIE FRONT VIE *3" (76) typical depth. Shaded areas will be visible and should be finished to match cabinetry. NOTE: Shaded line represents profile of unit with 3 /4" (19) panel. FLUSH INSET IDTH MODEL S-30 32" (813) Dimensions assume a 3 /4" (19) panel thickness. If an 83" (2108) grille height is specified, the flush inset height must be decreased by 7 /8" (22). If an 88" (2235) grille height is specified, the flush inset height must be increased by 4" (102). If two units are installed side by side, refer to page 11 for dual flush inset installations. subzero.com/specs 9
INE STORGE Opening Dimensions MODEL S-30 DUL STNDRD INSTLLTION 24" (610) OPENING DEPTH TOP VIE 83 3 /4" (2127) OPENING HEIGHT OPENING IDTH SIDE VIE FRONT VIE NOTE: Shaded line represents profile of unit. OPENING IDTH MODELS S-30 and 30" Built-In 59 3 /4" (1518) S-30 and 36" Built-In 65 3 /4" (1670) dual installation kit will be required for this installation. 10 Sub-Zero Customer Care 800.222.7820
INE STORGE Opening Dimensions MODEL S-30 DUL FLUSH INSET INSTLLTION 26 3 /16" (665) FLUSH INSET DEPTH 2 3 /16" (56) FINISHED CLETS* TOP VIE 1 /4" (6) 1 1 /4" (32) 84" (2134) FLUSH INSET HEIGHT FLUSH INSET IDTH 1 1 /4" (32) 4" (102) 3" (76)* TYPICL 2 3 /16" (56) SIDE VIE FRONT VIE *3" (76) typical depth. Shaded areas will be visible and should be finished to match cabinetry. NOTE: Shaded line represents profile of unit with 3 /4" (19) panel. FLUSH INSET IDTH MODELS S-30 and 30" Built-In 62 1 /4" (1581) S-30 and 36" Built-In 68 1 /4" (1734) Dimensions assume a 3 /4" (19) panel thickness. dual installation kit will be required for this installation. subzero.com/specs 11
INE STORGE Electrical The electrical supply should be located within the shaded area shown in the illustration for your specific model. For model 315, the electrical supply can be located anywhere on the back wall of the opening. separate circuit, servicing only this appliance is required. ground fault circuit interrupter (GFCI) is not recommended and may cause interruption of operation. If the unit will be connected to a home security system, allow 36" (914) of excess wiring for proper connection. IMPORTNT NOTE: For models 427G and 427RG, it is critical the electrical outlet be positioned with the grounding prong to the right of the thinner blades. Installation must comply with all applicable electrical codes. ELECTRICL REQUIREMENTS Electrical Supply Service Receptacle 115 VC, 60 Hz 15 amp 3-prong grounding-type Custom Panels For framed, overlay, integrated and flush inset applications, custom door panels must be provided. Handle hardware must also be provided for overlay, integrated and flush inset applications. Refer to panel requirements and custom panel dimensions charts for your specific model and design application. Do not install a solid panel on a glass door unit. solid door is available as a sales accessory (except model 315 and S-30) and must be installed if a solid panel is being specified. Service may be required to install the door. Contact an authorized Sub-Zero dealer for more information. Overall dimensions are the same for glass and solid door panels. Finish all sides of the custom panels. They may be visible when the door is open or through the window of glass door models. Model 424FSG has a finished stainless steel exterior that is designed to be used in a freestanding application. LEFT SIDE OF OPENING LEFT SIDE OF OPENING 2" (51) 15 1 /2" (394) 3" (76) 2 1 /2" (64) 13" (330) 4 1 /2" (114) FLOOR 1/4" (6) FLOOR Model 424G. Models 427G and 427RG. 7" (178) E 6" (152) 75 1 /2" (1918) FROM FLOOR RIGHT SIDE OF OPENING Model S-30. 12 Sub-Zero Customer Care 800.222.7820
INE STORGE Custom Panels 315 and 424G For models 315 and 424G, the custom door panel will attach directly to the door frame with screws through a series of pre-drilled holes. OVERLY PNEL DIMENSIONS Refer to the charts for panel requirements and dimensions. H PNEL REQUIREMENTS PNEL EIGHT 315 424G MX 10 lb (5 kg) 10 lb (5 kg) 315 / 424G PNEL THICKNESS MIN ll Panels 5 /8" (16) PNEL DIMENSIONS MODEL H 315 15" (381) 30 1 /16" (764) 424G 23 3 /4" (603) 30 1 /16" (764) STILES / RILS (MIN) 315 2 1 /4" (57) 424G 2 1 /4" (57) DOOR CLERNCE Models 315 and 424G can be installed flush with surrounding cabinetry. Depending on the thickness of the overlay door panel, it may be necessary to install the unit 1 /4" (6) beyond the front surface of adjacent cabinetry to prevent interference when the door is opened to 145. Refer to the full-scale template on page 23. subzero.com/specs 13
INE STORGE Custom Panels 427G and 427RG For models 427G and 427RG, the custom door panel will attach directly to the door with screws through a series of pre-drilled holes. For model 427RG, the drawer panels will attach using mounting brackets supplied with the unit. Refer to the panel requirements chart and integrated panel dimensions. The thickness of the custom panel can vary. minimum 5 /8" (16) thick panel is required, but the thickness can be increased provided it does not exceed the weight limit. The depth of each model is 24" (610). llow for panel thickness when planning the finished opening depth. CUTION hen using a 3 /4" (19) or thicker panel with a reveal less than 1 /4" (6), panel may cause damage to the unit when door is opened to 105. Use the built-in 90 door stop. Finish all sides of custom panels. They will be visible when the door/drawer is open. D-style handles are recommended. Door handles must be located near the edge of the panel opposite the hinge and should be centered top to bottom. Drawer handles must be located near the top edge of each panel. Stainless steel tubular and pro handles are avail able through an authorized Sub-Zero dealer. For local dealer information, visit the find a showroom section of our website, subzero.com. n optional lock kit is available for models 427G and 427RG. Review the lock kit instructions to ensure your panels will allow for adequate installation. These instructions are available on our website, subzero.com/specs. CUTION s reveals between cabinetry and the unit decrease, severe finger pinching can occur while door is closing. PNEL REQUIREMENTS PNEL EIGHT Door Drawer (427RG) MX 20 lb (9 kg) 12 lb (5 kg) PNEL THICKNESS MIN ll Panels 5 /8" (16) 14 Sub-Zero Customer Care 800.222.7820
INE STORGE Custom Panels 427G and 427RG INTEGRTED PNEL DIMENSIONS DUL INSTLLTION B B For dual installations, refer to the illustration for panel heights and the chart below for panel widths. PNEL IDTH 75 7 /8" (1927) C 45 3 /8" (1153) 13 9 /16" (345) MODEL 427G 26 13 /16" (681) 427RG 26 13 /16" (681) STILES / RILS (MIN) B C 427G 2 1 /4" (57) 3 3 /4" (95) 8" (203) 427RG 2 1 /4" (57) 3 3 /4" (95) 3" (76) C 16 11 /16" (424) 427G 427RG Typical panel dimensions are based on an 80" (2032) overall height, 4" (102) toe kick and 1 /8" (3) reveals. Panel dimensions must be adjusted accordingly for all other installations. Refer to the illustration for panel heights and the chart below for panel widths. PNEL IDTH MODEL 427G 26 3 /4" (679) 427RG 26 3 /4" (679) STILES / RILS (MIN) B C 427G 2 1 /4" (57) 3 3 /4" (95) 8" (203) 427RG 2 1 /4" (57) 3 3 /4" (95) 3" (76) subzero.com/specs 15
INE STORGE Custom Panels 427G and 427RG DOOR PNEL HEIGHT The height of the custom door panel can extend beyond the typical panel height, provided it does not exceed the weight limit. Refer to the illustration below. TOE KICK CLERNCE The height of the toe kick area can extend beyond the typical toe kick height, provided it does not exceed the dimensions in the illustration below. 1 1 /2" (38) 25" (635) TO LL INTEGRTED UNIT (SIDE VIE) 1 /8" (3) DECORTIVE VLNCE CNNOT EXTEND BEYOND THE FRONT OF THE MOLDING OVERLL HEIGHT DOOR PNEL DECORTIVE VLNCE HEIGHT OF PNEL KICKPLTE / GRILLE CN BE DJUSTED FORRD KICKPLTE / GRILLE MINIMUM HEIGHT 1/8" (3) TYPICL HEIGHT OF DOOR PNEL HINGE REMOVBLE MOLDING INTEGRTED UNIT (SIDE VIE) 4" (102) TO 9" (229) FROM FLOOR BSE MOLDING MUST BE REMOVBLE 4" (102) MX HEIGHT 25" (635) TO LL 2 5 /8" (67) TO 4" (102) Upper valance side view. Toe kick side view. 16 Sub-Zero Customer Care 800.222.7820
INE STORGE Custom Panels S-30 FRMED PNEL FRMED PNEL DIMENSIONS The framed application is an overlay model with framed design features. It is not a separate model. H If the custom panel is thinner than 1 /4" (6), a filler material must be added to achieve a proper fit. If the panel is thicker than 1 /4" (6), rout an edge around the panel or mount the custom panel on a sheet of 1 /4" (6) thick material and insert into the channel. H Routing, recessing and optional extended handles may be required for finger clearance. Refer to the full-scale template on page 26. PNEL REQUIREMENTS PNEL EIGHT Door Grille (optional) MX 75 lb (34 kg) 13 lb (6 kg) PNEL THICKNESS MIN Framed 1 /4" (6) S-30 FRMED PNELS PNEL H Door 29 3 /4" (756) 69 9 /16" (1767) Grille (optional) 29 3 /4" (756) 8 15 /16" (227) STILES / RILS Minimum 3 1 /8" (79) subzero.com/specs 17
INE STORGE Custom Panels S-30 OVERLY PNELS OVERLY PNEL DIMENSIONS Overlay panels are typically created by combining a 3 /4" (19) custom panel, a.10" (3) spacer panel and a 1 /4" (6) backer panel. Refer to the illustrations below. H PNEL REQUIREMENTS PNEL EIGHT Door Grille MX 75 lb (34 kg) 13 lb (6 kg) H PNEL THICKNESS MIN Overlay 5 /8" (16) SPCER PNEL CUSTOM PNEL BCKER PNEL 1 /8" (3) TRIM DOOR FRME 5/16" (8) min GLSS Panel assembly cross section (overlay). CUSTOM PNEL 3/4" (19) typical 1/4" (6).10" (3) SPCER PNEL BCKER PNEL Panel assembly rear view. S-30 OVERLY PNELS DOOR H Overlay Panel 30" (762) 69 3 /4" (1772) Spacer Panel 29 1 /8" (740) 68 15 /16" (1751) Backer Panel 29 3 /4" (756) 69 9 /16" (1767) STILES / RILS Minimum 3 1 /4" (83) GRILLE H Overlay Panel 30" (762) 9 1 /4" (235)* Spacer Panel 29 1 /8" (740) 8 5 /16" (211) Backer Panel 29 3 /4" (756) 8 15 /16" (227) *Panel height may be increased by 7 /16" (11) to hide upper main frame. For more information, refer to the built-in panel configurator at subzero.com/trade/panels. Grille panel dimensions are for standard 84" (2134) overall unit height. For 83" (2108) height, subtract 1" (25) from grille panel height dimensions and for 88" (2235) height, add 4" (102). specific panel grille must be ordered for an 83" or 88" overall unit height. 18 Sub-Zero Customer Care 800.222.7820
INE STORGE Custom Panels S-30 FLUSH INSET PNELS FLUSH INSET PNEL DIMENSIONS The flush inset application is an overlay model with flush inset panels. It is not a separate model. H The flush inset design allows custom panels to be installed flush with adjacent cabinets. Similar to overlay, flush inset panels are typically created by combining a 3 /4" (19) custom panel, a.10" (3) spacer panel and a 1 /4" (6) backer panel. Refer to the illustrations for overlay panels on the previous page. H For flush inset panels thicker than 3 /4" (19), a 90 door stop may be required to prevent interference with adjacent cabinets. Refer to the full-scale template on page 29. PNEL REQUIREMENTS PNEL EIGHT MX Door 75 lb (34 kg) Grille 13 lb (6 kg) PNEL THICKNESS MIN Flush Inset 5 /8" (16) S-30 FLUSH INSET PNELS DOOR H Flush Inset Panel 31" (787) 69 3 /4" (1772) Spacer Panel 29 1 /8" (740) 68 15 /16" (1751) Backer Panel 29 3 /4" (756) 69 9 /16" (1767) STILES / RILS Minimum 3 3 /4" (95) GRILLE H Flush Inset Panel 31" (787) 9 1 /4" (235) Spacer Panel 29 1 /8" (740) 8 5 /16" (211) Backer Panel 29 3 /4" (756) 8 15 /16" (227) Grille panel dimensions are for standard 84" (2134) overall unit height. For 83" (2108) height, subtract 1" (25) from grille panel height dimensions and for 88" (2235) height, add 4" (102). specific panel grille must be ordered for an 83" or 88" overall unit height. subzero.com/specs 19
INE STORGE Custom Panels S-30 FLUSH INSET PNEL OFFSETS TOP VIE The illustrations provide panel offsets and reveals for model S-30 in a flush inset application. Refer to the chart below for reference to the illustrations. PNEL OFFSET DOOR / DRER / GRILLE BCKER SPCER CBINETRY CBINETRY GRILLE 1 5 /8" /16" (3) (8) 1 /2"(13) FLUSH INSET Door / Grille Sides Grille Top Grille Bottom / Door Top Door Bottom ILLUS B C D FLUSH INSET PNEL 5/16" (8) 1 /2" (13) 5/8" (16) SIDE VIE Illus. Illus. B DOOR / DRER GRILLE 5 /16" (8) 5/32" (4) 1/2"(13) 5 /16" (8) DOOR 3 /32" 5 /16" (2) (8) SIDE VIE SIDE VIE 3 /32" (2) Illus. C Illus. D 20 Sub-Zero Customer Care 800.222.7820
INE STORGE Custom Panels S-30 DUL INSTLLTIONS DUL FLUSH INSET PNEL DIMENSIONS If two models S-30 or a model S-30 and built-in unit are installed side by side, a dual installation kit may be required. Installations without a custom filler strip require a dual installation kit. If a dual installation kit is not specified, a 2" (51) filler strip is recommended between units. Dual installations without a filler strip can only be accomplished using two units with opposite hinges. Refer to the illustrations below. H H Dual installation kits are available through an authorized Sub-Zero dealer. For local dealer information, visit the find a showroom section of our website, subzero.com. For questions regarding the installation, call Sub Zero customer care at 800-222-7820. For dual standard installations, panel dimensions are the same as for single installations. Refer to the chart on the previous page. Panel dimensions and offsets for dual flush inset installations are listed on the following pages. S-30 MODEL S-30 DOOR H Flush Inset Panel 30 1 /2" (775) 69 3 /4" (1772) Spacer Panel 29 1 /8" (740) 68 15 /16" (1751) Backer Panel 29 3 /4" (756) 69 9 /16" (1767) STILES / RILS Minimum 3 3 /4" (95) GRILLE H Flush Inset Panel 30 1 /2" (775) 9 1 /4" (235) Spacer Panel 29 1 /8" (740) 8 5 /16" (211) Backer Panel 29 3 /4" (756) 8 15 /16" (227) ITHOUT FILLER STRIP FILLER STRIP Grille panel dimensions are for standard 84" (2134) overall unit height. For 83" (2108) height, subtract 1" (25) from grille panel height dimensions and for 88" (2235) height, add 4" (102). specific panel grille must be ordered for an 83" or 88" overall unit height. Opposite hinges. Same side hinges. subzero.com/specs 21
INE STORGE Custom Panels S-30 DUL FLUSH INSET PNEL OFFSETS TOP VIE TOP VIE The illustrations provide panel offsets and reveals for model S-30 in a dual flush inset application. Refer to the chart below for reference to the illustrations. PNEL OFFSET DOOR / DRER / GRILLE BCKER SPCER CBINETRY DOOR DUL TRIM DOOR DUL FLUSH INSET Door (hinge) / Grille Sides Door (handle) Sides Grille Top Grille Bottom / Door Top Door Bottom ILLUS B C D E FLUSH INSET PNEL Illus. 5/16" (8) 1 /2" (13) 5/8" (16) 5 /16" (8) 1/8" (3) Illus. B 1/4" (6) REVEL CBINETRY 1 /2"(13) GRILLE 5 /16" (8) 5 /32" (4) GRILLE 1 5 /8" /16" (3) (8) 1 /2"(13) DOOR 3 /32" 5/16" (2) (8) SIDE VIE SIDE VIE Illus. C Illus. D DOOR / DRER 5 /16" (8) SIDE VIE 3/32" (2) Illus. E 22 Sub-Zero Customer Care 800.222.7820
INE STORGE Custom Panels S-30 SIDE PNEL The custom side panel must be a minimum of 24" (610) deep and 1 /2" (13) thick. Routing will be necessary for the side panel to fit flush against the side of the unit. Refer to the illustrations below. hen installing model S-30 with a custom side panel, an accessory kit is required. Stainless steel and white enamel side panels are available through an authorized Sub-Zero dealer. For local dealer information, visit the find a showroom section of our website, subzero.com. Handle Hardware Optional stainless steel tubular and pro handles are available through an authorized Sub-Zero dealer. For local dealer information, visit the find a showroom section of our website, subzero.com. Refer to the chart below for the length and stud spacing of standard handles for wine storage models. STNDRD HNDLES 315, 424G, 424FSG LENGTH STUD SPCING Tubular 24 3 /16" (614) 16 1 /4" (413) Pro 21" (533) 19 11 /16" (500) 24" (610) 427RG (DRER) LENGTH STUD SPCING Tubular 24 3 /16" (614) 16 1 /4" (413) Pro 21" (533) 19 11 /16" (500) FRONT OF SIDE PNEL 1" (25) 1 7 /8" (48) 427G, 427RG (DOOR) LENGTH STUD SPCING Tubular 41 3 /16" (1046) 33 1 /4" (845) Pro 39 9 /16" (1006) 38 5 /16" (973) S-30 LENGTH STUD SPCING Tubular 63 7 /8" (1622) 43 7 /8" (1114) Pro 45 3 /16" (1147) 43 7 /8" (1114) ROUT TO 1 /8" (3) 1 /8" (3) 1 /2" (13) 1 7 /8"(48) 1" (25) 84" (2134) MIN FRME SIDE PNEL ROUTING Routing detail. 4" (102) OPTIONL TOE KICK CUT-OUT 2 5 /8" (67) Side panel dimensions. subzero.com/specs 23
INE STORGE ine Shelf ood Facing FULL-SCLE TEMPLTE The natural cherrywood facing on wine storage shelves can be stained and sealed or replaced with wood more complementary to surrounding cabinetry. Refer to the full-scale template and chart for dimensions. IDTH MODEL 315 10 15 /16" (278) 424G, 424FSG 19 1 /2" (495) 427G, 427RG 20 15 /16" (532) S-30 24 9 /16" (624) 5 /8" (16) MXIMUM THICKNESS 7 /64" (3) 1 1 /2" (38) 27 /32" (21) 5 /64" (2) (IDTH) 23 /64" (9) 9 /16" (14) FRONT VIE SIDE VIE ine shelf wood facing. 24 Sub-Zero Customer Care 800.222.7820
INE STORGE Door Clearance 315 and 424G FULL-SCLE TEMPLTE To allow for a 145 door opening, the unit should extend a minimum of 1 /4" (6) beyond the front surface of adjacent cabinetry. The unit can be installed flush, however, there is potential for interference with the panel if the door is opened past 90. UNDERCOUNTER UNIT DJCENT CBINETRY DOOR CLOSED 1 /2" (13) 3 /4" (19) DOOR PNEL 1 /4" (6) 1 /8" (3) HINGE DETENT T 145 OPENING (DOOR OPENS PST 145 ) 0" 1" (25) SCLE 145 door opening (top view). subzero.com/specs 25
INE STORGE Framed Panel S-30 FULL-SCLE TEMPLTE OPTIONL EXTENDED FULL-LENGTH HNDLE 1" (25) STNDRD FULL-LENGTH HNDLE 2" (51) 3" (76) 1 1 /4" (32) PNEL 1" (25) PNEL 3/4" (19) PNEL 1 /2" (13) PNEL 1 /4" (6) FRMED PNEL DOOR Framed panel thickness. 26 Sub-Zero Customer Care 800.222.7820
INE STORGE Overlay and Flush Inset Panels S-30 FULL-SCLE TEMPLTE Overlay and flush inset panels must be a minimum of 5 /8" (16) thick to support mounting the handle. Panel thickness does not include backer and spacer panel. Mount handle close to the opening edge of the door. DEPTH OF TUBULR ND PRO HNDLES 1" (25) 2" (51) 3" (76) 1 1 /4" (32) PNEL 1" (25) PNEL 3/4" (19) PNEL.10" (3) SPCER PNEL 1 /4" (6) BCKER PNEL DOOR Overlay and flush inset panel thickness. subzero.com/specs 27
INE STORGE Overlay pplication S-30 FULL-SCLE TEMPLTE 23 7 /8" (606) TO RER OF UNIT OVERLL IDTH OF UNIT 0" (0) 1 /4" (6) 1/2" (13) 3 /4" (19) 1" (25) 1 1 /4" (32) 1 1 /2" (38) 1 3 /4" (44) 2" (51) 2 1 /4" (57) 2 1 /2" (63) 2 3 /4" (70) 3" (76) 3 1 /4" (83) 3 1 /2" (89) 1" (25) THICK PNEL 3/4" (19) THICK OVERLY PNEL (TYPICL) 1/4" (6) BCKER PNEL 0" 1" (25) SCLE 90 door opening (top view). 28 Sub-Zero Customer Care 800.222.7820
INE STORGE Flush Inset pplication S-30 FULL-SCLE TEMPLTE 24" (610) TO BCK LL For panels thicker than 3 /4" (19), a 90 door stop may be required to prevent interference with adjacent cabinets. 1 1 /4" (32) 2 3 /16" (56) SSUMES 3/4" (19) FLUSH INSET PNEL THICKNESS 1" (25) THICK PNEL 3/4" (19) THICK FLUSH INSET PNEL (TYPICL) 1/4" (6) BCKER PNEL 0" 1" (25) SCLE 110 door opening (top view). subzero.com/specs 29
INE STORGE FILLER STRIP 1 1 /4" (32) PPROX PROFILE OF STINLESS STEEL RPPED DOOR ND HNDLE DOOR CLOSED Dual Standard Installation S-30 DOOR OPEN 110 FULL-SCLE TEMPLTE Typical framed, overlay or stainless steel dual installation with filler strip at maximum 110 door opening. Panel thickness may require a 90 door stop. 0" 1" (25) SCLE Dual standard installation (top view). 30 Sub-Zero Customer Care 800.222.7820
INE STORGE FILLER STRIP 1 1 /2" (38) 1 /2" (13) PROFILE OF 3/4" (19) FLUSH INSET PNEL ND TUBULR HNDLE DOOR CLOSED Dual Flush Inset Installation S-30 DOOR OPEN 110 FULL-SCLE TEMPLTE Typical flush inset dual installation with filler strip at maximum 110 door opening. Panel thickness may require a 90 door stop. 0" 1" (25) SCLE Dual flush inset installation (top view). subzero.com/specs 31
Sub-Zero Residential Limited arranty FOR RESIDENTIL USE FULL TO YER RRNTY* For two years from the date of original installation, this Sub-Zero product warranty covers all parts and labor to repair or replace, under normal residential use, any part of the product that proves to be defective in materials or workmanship. ll service provided by Sub-Zero under the above warranty must be performed by Sub-Zero factory certified service, unless otherwise specified by Sub-Zero, Inc. Service will be provided during normal business hours. FULL FIVE YER SELED SYSTEM RRNTY For five years from the date of original installation, this Sub-Zero product warranty covers all parts and labor to repair or replace, under normal residential use, these parts that prove to be defective in materials or workmanship: compressor, condenser, evaporator, drier and all connecting tubing. ll service provided by Sub-Zero under the above warranty must be performed by Sub-Zero factory certified service, unless otherwise specified by Sub-Zero, Inc. Service will be provided during normal business hours. LIMITED TELVE YER SELED SYSTEM RRNTY For twelve years from the date of original installation, Sub-Zero will repair or replace the following parts that prove to be defective in materials or workmanship: compressor, condenser, evaporator, drier and all connecting tubing. If the owner uses Sub-Zero factory certified service, the service provider will repair or replace these parts with the owner paying for all other costs, including labor. If the owner uses non-certified service, the owner must contact Sub-Zero, Inc. (using the information below) to receive repaired or replacement parts. Sub-Zero will not reimburse the owner for parts purchased from non-certified service or other sources. TERMS PPLICBLE TO ECH RRNTY The warranty applies only to products installed for normal residential use. The warranty applies only to products installed in any one of the fifty states of the United States, the District of Columbia or the ten provinces of Canada. This warranty does not cover any parts or labor to correct any defect caused by negligence, accident or improper use, maintenance, installation, service or repair. THE REMEDIES DESCRIBED BOVE FOR ECH RRNTY RE THE ONLY ONES THT SUB-ZERO, INC. ILL PROVIDE, EITHER UNDER THIS RRNTY OR UNDER NY RRNTY RISING BY OPERTION OF L. SUB-ZERO, INC. ILL NOT BE RESPONSIBLE FOR NY CONSEQUENTIL OR INCIDENTL DMGES RISING FROM THE BRECH OF THIS RRNTY OR NY OTHER RRNTY, HETHER EXPRESS, IMPLIED OR STTUTORY. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. This warranty gives you specific legal rights and you may also have other legal rights that vary from state to state. To receive parts and/or service and the name of Sub-Zero factory certified service nearest you, contact Sub-Zero, Inc., P.O. Box 44848, Madison, I 53744; check the contact & support section of our website, subzero.com, email us at customerservice@subzero.com or call 800-222-7820. *Stainless steel (doors, panels, handles, product frames and interior surfaces) are covered by a limited 60-day parts and labor warranty for cosmetic defects. *Replacement water filters and air purification cartridges are not covered by the product warranty.
Sub-Zero, Sub-Zero & Design, Dual Refrigeration, Constant Care, The Living Kitchen, Great merican Kitchens The Fine rt of Kitchen Design, and Ingredients are registered trademarks and service marks of Sub-Zero, Inc. olf, olf & Design, olf Gourmet, & Design and the color red as applied to knobs are registered trademarks and service marks of olf ppliance, Inc. (collectively, the Company Marks. ) ll other trademarks or registered trademarks are property of their respective owners in the United States and other countries.
SUB-ZERO, INC. P.O. BOX 44848 MDISON, I 53744 SUBZERO.COM 800.222.7820 SZSDG 9/2013