INSTALLATION GUIDE INSTALLATION GUIDE

CONTACT US By selecting Hiku fn, you ve chosen qulity design, heightened comfort nd effortless conservtion. Use this guide to sfely instll your fn. Plese contct us with ny questions you my hve. United Sttes 2348 Innovtion Drive Lexington, KY 40511 855 694 2458 Austrli/Oceni Unit 22, 1029 Mnly Rod Tinglp QLD 4173, Austrli 1 300 BIG ASS Europe OBELIS S.A Bd. Générl Whis, 53 1030 Brussels, Belgium +32.2.732.59.54 Asi Pcific 18 Tmpines Industril Crescent #06-07 Singpore 528 605 +65 6709 8500 Est Asi Room 808, Ti Yu Building 181 Johnston Rod Wn Chi, Hong Kong +852 2836 5808 Scn for online Hiku Home pp help

Instlltion Guide For opertion, mintennce, nd trouleshooting informtion, visit hikuhome.com/help Models: K3150-A2, K3150-S0, K3150-X2 Topic Pge Technicl Specifictions 3 Tools Needed 3 Prts nd Hrdwre Low Profile Mount 4 Stndrd Mount 5 Universl Mount 6 Prepre the Fn Site 7 Instll Your Fn Airfoils 8 Lower Cover nd Trim 10 Mounting Brcket 12 Mounting: Low Profile 22 Mounting: Stndrd 30 Mounting: Universl 42 Test Your Fn 54 READ AND SAVE THESE INSTRUCTIONS

NOTES

!!! Disconnect power to the fn loction! Do not use the fn with dimmer switch! A licensed electricin must instll the fn if required y your locl electricl code. The ground wire must e connected to the supply ground nd its length must e longer thn the sfety cle! Technicl Specifictions Dimeter Weight Operting voltge Operting frequency 132 cm 6.4 kg 100 240 VAC, 1 Φ 50 60 Hz 152 cm 7.3 kg 100 240 VAC, 1 Φ 50 60 Hz 213 cm 11.3 kg 100 240 VAC, 1 Φ 50 60 Hz Tools Needed Ldder Wire Strippers Phillips Screwdriver Wrenches Box Contents As you remove the fn from its pckging, mke sure you re not missing ny components required for ssemly nd opertion. If you ordered multiple fns, e sure to keep the components of ech fn together! HAIKU HOME 3

PARTS & HARDWARE: LOW PROFILE MOUNT c Mounting plte (2) Ruer umper (2) Mounting rcket c d Lower cover e f g Lower cover trim (3) Airfoil Motor hu j h i j (2) Extension tue screw cp Remote control Mounting hrdwre (4) 6 mm Nylock nut Sfety cle shckle i l g h k Airfoil hrdwre (6) M5 irfoil screw (6) 5 mm lock wsher k l Wiring hrdwre (2) 3-lever wire connector 5-lever wire connector Wire nut (2) Wiring cover screw f d e Use the two screw cps tht mtch the color of your fn. Sfety cle not shown Use for ground wires 4 REV. D 2015 HAIKU HOME. ALL RIGHTS RESERVED.

PARTS & HARDWARE: STANDARD MOUNT Ruer ushing c Mounting rcket c (2) Mounting rce rcket d Wiring cover e Wiring cover trim k k f Lower cover g h Lower cover trim (3) Airfoil d i j k l m Motor hu Remote control Mounting hrdwre (2) M6 x 1 x 25 mm socket cp screw (2) M6 x 1 nylock nut M8 Bolt 8 mm flt wsher 8 mm lock wsher M8 nut 2 mm x 2 mm split pin Sfety cle shckle Airfoil hrdwre (6) M5 irfoil screw (6) 5 mm lock wsher Wiring hrdwre (2) 3-lever wire connector 5-lever wire connector Wire nut (2) Wiring cover screw j Do not use the mounting rcket if mounting the fn to concrete ceiling. If instlling the fn to junction ox, U-shped ceiling hook, or wood ceiling joist, only one (1) olt nd one (1) nut re needed. If instlling the fn to J-shped ceiling hook, two (2) olts nd two (2) nuts re needed. Sfety cle not shown Use for ground wires h m i l e g f HAIKU HOME 5

PARTS & HARDWARE: UNIVERSAL MOUNT Mounting rcket c Mounting ll & wedge Cnopy d e Extension tue Wiring cover m c f (3) Airfoil g Motor hu d h Lower cover i Lower cover trim j Remote control k l Mounting hrdwre 4 mm self-tpping screw 6 mm steel pin (6) M4 x 6 screw (2) M4 lock wsher Sfety cle shckle (2) Motor rcket M6 x 32 mm olt M6 x 28 mm olt (2) M6 nut Airfoil hrdwre (6) M5 irfoil screw (6) 5 mm lock wsher j k l e g m Wiring hrdwre (2) 3-lever wire connector 5-lever wire connector Wire nut Cle tie Sfety cle not shown Use for ground wires f i h 6 REV. D 2015 HAIKU HOME. ALL RIGHTS RESERVED.

1 PREPARE THE FAN SITE Instlltion requires sic electricl knowledge. Contct licensed electricin if you re uncomfortle performing electricl work! 1 Disconnect Power! Mounting Structure If you re instlling the fn directly to the uilding structure 2 or to ceiling-mounted outlet ox, the structure or outlet ox must e suitle for fn support. Disconnect power to the fn loction efore wiring the fn! A redily ccessile disconnect device shll e incorported externl to the equipment. HAIKU HOME 7

1 Moving clockwise round the fn, lign ech irfoil on the fn hu nd secure it with the screws nd wshers. Mke sure the stickers on the irfoils mtch the stickers on the fn hu. Hrdwre:. M5 irfoil screw. 5 mm lock wsher 2 Remove nd recycle the plstic protective cover (c). STEPS COMPLETED HAIKU HOME 9

3 INSTALL THE LOWER COVER AND TRIM If you purchsed the Hiku Light Kit, proceed to the instructions included with the kit. Return to these instructions once the kit is instlled. INSTALL LOWER COVER INSTALL LOWER COVER TRIM 1 2 10 REV. D 2015 HAIKU HOME. ALL RIGHTS RESERVED.

1 2 Position the lower cover over the fn motor, nd then plce oth hnds flt on the cover nd turn it clockwise to lock it in plce. Align the four slots on the lower cover trim with the four smll round ts on the fn hu. Press nd turn the lower cover trim clockwise to lock it into plce. STEPS COMPLETED HAIKU HOME 11

INSTALL THE MOUNTING BRACKET Outlet Box If your locl electricl code requires the fn to e instlled on ceiling-mounted outlet ox, the outlet ox must e suitle for fn support. If there is not n outlet ox t the fn loction, one should e instlled on ceiling joist or em nd properly wired. Concrete Ceiling If instlling your fn on concrete ceiling, ensure power wiring hs een routed to the fn site. Low Profile Mount. Attch the mounting plte directly to the ceiling using four Ø 8 mm nchor olts. If required y your locl uilding nd sfety code, instll Ø 14 mm nchor hook for the sfety cle. Stndrd Mount. Instll the fn where there is ceiling hook or other sufficient structurl support. If there is not hook t the fn site, instll hnger plte using three Ø 12 12.5 mm nchor olts. Do not use the mounting rcket supplied with the fn. If required y your locl uilding nd sfety code, instll n Ø 8 8.5 mm nchor hook for the sfety cle. Universl Mount. Attch the mounting rcket directly to the ceiling using three Ø 6 mm nchor olts. If required y your locl uilding nd sfety code, instll n Ø 8 mm nchor hook for the sfety cle. Wood Ceiling Joist If instlling your fn on wood ceiling joist, ensure power wiring hs een routed to the fn site. Attch the mounting plte or mounting rcket directly to the joist using two wood screws (not supplied). Hiku Home recommends using corrosion-resistnt 12-11 x 45 mm hex hed timer screws with sel. 12 REV. D 2015 HAIKU HOME. ALL RIGHTS RESERVED.

4 Outlet Box Pge 14 4 Concrete Ceiling Pge 16 4c Wood Ceiling Joist Pge 18 HAIKU HOME 13

4 INSTALL THE MOUNTING BRACKET (OUTLET BOX) Low Profile Mount Stndrd Mount Universl Mount Instlltion my vry. Refer to the outlet ox instructions. Instlltion my vry. Refer to the outlet ox instructions. Instlltion my vry. Refer to the outlet ox instructions. 14 REV. D 2015 HAIKU HOME. ALL RIGHTS RESERVED.

! Mke sure power is disconnected from the fn loction efore instlling the mounting plte or mounting rcket! If instlling Stndrd Mount fn, set the ruer ushing () in the eye of the mounting rcket. Secure the mounting plte or mounting rcket () to the outlet ox with the hrdwre supplied with the outlet ox. Refer to the outlet ox instructions. If instlling Universl Mount fn to sloped ceiling, secure the mounting rcket so tht the open side of the rcket is fcing up the slope of the ceiling. HAIKU HOME 15

4 INSTALL THE MOUNTING BRACKET (CONCRETE CEILING) Instll n nchor hook for the sfety cle if required y your locl uilding nd sfety code. Low Profile Mount Stndrd Mount Universl Mount Ø 12 12.5 mm Ø 6 mm 40 mm 100 mm 45 mm 112 mm Ø 8 mm (nchor olt) Ø 14 mm (nchor hook) 80 mm 35 mm 35 mm 45 mm 43 mm c 50 mm mx 40 mm mx c 35 40 mm 35 40 mm c 50 mm mx 40 mm mx 16 REV. D 2015 HAIKU HOME. ALL RIGHTS RESERVED.

! Mke sure power is disconnected from the fn loction efore instlling the mounting plte or mounting rcket! Low Profile Mount Drill four Ø 8 mm holes in the pttern shown. The hole depth should not exceed 40 mm. Remove ny dust from the holes. Insert four nchor olts () into the holes. Strike the heds of the nchor olts with hmmer, ensuring the olt sleeves re flush with the ceiling surfce. Position the mounting plte () on the nchor olts. Ensure ll four nchor olts re fully tightened to expnd nd lock the nchors. If required y locl uilding nd sfety codes, instll n nchor hook (c) for the sfety cle. Drill Ø 14 mm hole for the nchor hook in the pttern shown. The hole depth should not exceed 50 mm. Remove ny dust from the hole, nd then insert the nchor hook nd fully tighten. Stndrd Mount Drill three Ø 12 12.5 mm holes in the pttern shown. The hole depth should not exceed 35 40 mm. Remove ny dust from the holes. Insert three nchor olts () into the holes. Strike the heds of the nchor olts with hmmer, ensuring the olt sleeves re flush with the ceiling surfce. Position the hnger plte () on the nchor olts. Ensure ll three nchor olts re fully tightened to expnd nd lock the nchors. If required y locl uilding nd sfety codes, instll n nchor hook (c) for the sfety cle. Drill n Ø 8 8.5 mm hole for the nchor hook djcent to the hnger plte. The hole depth should not exceed 35 40 mm. Remove ny dust from the hole, nd then insert the nchor hook nd fully tighten. Universl Mount Drill three Ø 6 mm holes in the pttern shown. The hole depth should not exceed 40 mm. Remove ny dust from the holes. Insert three nchor olts () into the holes. Strike the heds of the nchor olts with hmmer, ensuring the olt sleeves re flush with the ceiling surfce. Position the mounting rcket () on the nchor olts. Ensure ll three nchor olts re fully tightened to expnd nd lock the nchors. If required y locl uilding nd sfety codes, instll n nchor hook (c) for the sfety cle. Drill n Ø 8 mm hole for the nchor hook. The hole depth should not exceed 50 mm. Remove ny dust from the hole, nd then insert the nchor hook nd fully tighten. HAIKU HOME 17

4c INSTALL THE MOUNTING BRACKET (WOOD CEILING JOIST) Low Profile Mount Stndrd Mount Universl Mount ceiling joist ceiling joist ceiling joist Not Supplied Not Supplied Not Supplied 18 REV. D 2015 HAIKU HOME. ALL RIGHTS RESERVED.

! Mke sure power is disconnected from the fn loction efore instlling the mounting plte or mounting rcket! If instlling Stndrd Mount fn, set the ruer ushing () in the eye of the mounting rcket (). Secure the mounting plte or mounting rcket () to the joist with two 12-11 x 45 mm hex hed timer screws with sel (not supplied). If instlling Universl Mount fn to sloped ceiling joist, secure the mounting rcket so tht the open side of the rcket is fcing up the slope of the joist. HAIKU HOME 19

MOUNT THE FAN Low Profile Mount The low profile mount cn e instlled on flt ceilings tht re s low s 8 feet (2.4 m). This mount is ville for fns with 52-inch (132-cm) or 60-inch (152-cm) dimeters. Stndrd Mount The stndrd mount moves ir most efficiently when instlled on flt ceilings rnging from 8.5 12 feet (2.5 3.7 meters) tll. This mount is ville for fns with 52-inch (132-cm) or 60-inch (152-cm) dimeters. Universl Mount The universl mount cn e instlled on sloped or flt ceilings rnging from 8.5 18 feet (2.5 5.5 meters) tll. This mount is ville for fns with 52-inch (132-cm), 60-inch (152-cm), or 84-inch (213-cm) dimeters. 5 Low Profile Mount Pge 22 20 REV. D 2015 HAIKU HOME. ALL RIGHTS RESERVED.

5 Stndrd Mount Pge 30 5c Universl Mount Pge 42 HAIKU HOME 21

1 Slide the ruer umpers () onto the extension tue rckets. STEP COMPLETED HAIKU HOME 23

2 Loosely ttch one mounting rcket to the mounting plte with the nylock nuts, ut do not fully tighten. Rise the fn to the rcket nd temporrily rest one ruer umper in the spce etween the rcket nd plte. This provides extr support when securing the sfety cle. Hrdwre:. 6 mm nylock nuts 3 While supporting the fn, loop the sfety cle round the mounting plte or uilding structure, nd then secure it with the shckle (). Allow the fn to hng from the sfety cle. Hrdwre:. Shckle STEPS COMPLETED HAIKU HOME 25

!!! 4 Disconnect power to the fn loction efore wiring the fn! A licensed electricin must instll the fn if required y your locl electricl code. Do not connect the fn to dmged power source! Do not ttempt to resolve electricl filures on your own. Consult qulified electricin if uncertin of the electricl instlltion of this fn. With the fn hnging from the sfety cle, insert the fn wires nd ceiling wires into the wire connectors. Test the connection y lightly tugging on the wires. AC Hot/L1 Brown AC Neutrl/L2 Blue PE/Erth Ground (connected to fn chssis) Green with Yellow Trcer Austrli Brown or Red Blck or Light Blue All other regions Brown Blue Green with Yellow Trcer HAIKU HOME 27

5 Rise the fn to the mount. Insert one ruer umper etween the mounting plte nd the loosely instlled mounting rcket. Position the other ruer umper (), nd then secure it with the remining mounting rcket () nd the nuts. Tighten ll hrdwre. Hrdwre: c. 6 mm nylock nuts 6 Slide the wiring cover (d) up the extension tue, llowing out 1/8 (3 mm) gp to the ceiling. Rotte the cover so tht the mounting slots lign with the screw holes on the extension tue, nd then secure it with the screws (e). Slide the trim (f) up the extension tue, ligning the ts on the inside with the slots on the ottom of the wiring cover. Twist clockwise to snp the trim into position. INSTALLATION COMPLETED HAIKU HOME 29

1 With the fn in the upright position, remove the protective covering from the extension tue. Slide the wiring cover () nd wiring cover trim () over the extension tue, resting them on the fn hu. STEP COMPLETED HAIKU HOME 31

2 Outlet Box or Wood Ceiling Joist Loosely instll the mount rce rckets () with the provided hrdwre. One olt should e inserted in the middle hole. Do not fully tighten the hrdwre. Hrdwre:. M6 x 1 x 25 mm socket cp screw c. M6 x 1 nylock nut J-Shped Ceiling Hook Mke sure the ceiling hook is cst into the concrete ceiling. Set the ruer ushing () in the eye of the ceiling hook (). Loosely instll the mount rce rckets (c) with the provided hrdwre. Two olts should e inserted in the outer holes. Do not fully tighten the hrdwre. Hrdwre: d. M6 x 1 x 25 mm socket cp screws e. M6 x 1 nylock nuts U-Shped Ceiling Hook Mke sure the ceiling hook is cst into the concrete ceiling. Set the ruer ushing () in the eye of the ceiling hook (). Loosely instll the mount rce rckets (c) with the provided hrdwre. One olt should e inserted in the middle hole. Do not fully tighten the hrdwre. Hrdwre: d. M6 x 1 x 25 mm socket cp screw e. M6 x 1 nylock nut HAIKU HOME 33

3 Rise the extension tue to the mount, nd insert the extension tue rckets etween the mount rckets () nd the ruer ushing so tht the mounting holes re ligned. Secure the extension tue with the mounting hrdwre. Fully tighten ll hrdwre so tht the rckets re slightly ent. Hrdwre:. M8 olt c. 8 mm flt wsher d. 8 mm lock wsher e. M8 nut f. 2 mm x 2 mm split pin HAIKU HOME 35

4 Outlet Box or Wood Ceiling Joist Loop the sfety cle round the mounting rcket or uilding structure, nd then secure it with the shckle (). J-Shped Ceiling Hook or Hnger Plte Secure the sfety cle to n nchor hook tht is properly instlled in the concrete ceiling. Loop the sfety cle round the ceiling hook nd through the nchor hook, nd then secure it with the shckle (). U-Shped Ceiling Hook Loop the sfety cle round the ceiling hook, nd then secure it with the shckle (). Hrdwre:. Shckle HAIKU HOME 37

!!! 5 Disconnect power to the fn loction efore wiring the fn! A licensed electricin must instll the fn if required y your locl electricl code. Do not connect the fn to dmged power source! Do not ttempt to resolve electricl filures on your own. Consult qulified electricin if uncertin of the electricl instlltion of this fn. Insert the fn wires nd ceiling wires into the wire connectors. Test the connection y lightly tugging on the wires. AC Hot/L1 Brown AC Neutrl/L2 Blue PE/Erth Ground (connected to fn chssis) Green with Yellow Trcer Austrli Brown or Red Blck or Light Blue All other regions Brown Blue Green with Yellow Trcer HAIKU HOME 39

6 7 Slide the wiring cover () up the extension tue, llowing out 1/8 (3 mm) gp to the ceiling. Rotte the wiring cover so tht the mounting slots lign with the screw holes on the extension tue, nd then secure it with the screws (). Mke sure tht there re no wires visile. If there is not enough clernce etween the cover nd ceiling, move the screw to the lower hole. Slide the wiring cover trim (c) up the extension tue, ligning the ts on the inside with the slots on the ottom of the wiring cover. Twist clockwise to snp into position. INSTALLATION COMPLETED HAIKU HOME 41

5c MOUNTING: UNIVERSAL Mke sure the extension tue is oriented so tht the wiring connector properly mtes with the connector from the fn hu. INSTALL MOTOR BRACKETS CONNECT WIRING HARNESS d c d 1 2 42 REV. D 2015 HAIKU HOME. ALL RIGHTS RESERVED.

1 With the fn in the upright position, loosely secure the motor rckets () to the motor shft with the M6 x 28 mm olt () nd nut (d). Instll the extension tue with the M6 x 32 mm olt (c) nd nut (d). Securely tighten oth olts. Hrdwre:. M6 x 28 mm olt c. M6 x 32 mm olt d. M6 nut 2 Plug the wiring hrness from the extension tue into the wiring hrness from the fn. STEPS COMPLETED HAIKU HOME 43

Mke sure the wires re tightly secured ginst the motor rckets so tht the wiring cover sets properly. 3 Instll the sfety cle () nd ground wire () lugs with the unpinted screws (c) nd lock wshers (d). Hrdwre: c. Unpinted M4 x 6 mm screws d. M4 lock wshers 4 5 Secure the wiring hrness (e) to the motor rckets with the provided cle tie. Mke sure the wires re tightly secured ginst the motor rckets so tht the wiring cover sets properly. Slide the wiring cover (f) down the extension tue, resting it on the fn hu. Mke sure no wires re visile etween the cover nd fn hu. Slide the cnopy (g) down the extension tue. STEPS COMPLETED HAIKU HOME 45

6 7 8 Slide the mounting ll () over the extension tue (). Insert the 6 mm steel pin (c) into the hole t the top of the extension tue, nd then slide the mounting ll upwrd, seting the steel pin in the inner slots. Insert the wedge (d) into the mounting ll nd secure it with the screw (e). Tighten the screw enough to prevent movement etween the mounting ll nd extension tue, ut do not overtighten. STEPS COMPLETED HAIKU HOME 47

!!! 9 Disconnect power to the fn loction efore wiring the fn! A licensed electricin must instll the fn if required y your locl electricl code. Do not connect the fn to dmged power source! Do not ttempt to resolve electricl filures on your own. Consult qulified electricin if uncertin of the electricl instlltion of this fn. Insert the fn wires nd ceiling wires into the wire connectors. Test the connection y lightly tugging on the wires. AC Hot/L1 Brown AC Neutrl/L2 Blue PE/Erth Ground (connected to fn chssis) Green with Yellow Trcer Austrli Brown or Red Blck or Light Blue All other regions Brown Blue Green with Yellow Trcer HAIKU HOME 49

10 Rise the fn to the mounting rcket. Align the ri in the mounting rcket () with the slot in the mounting ll (), position the mounting ll, nd let the fn hng freely. Gently twist the extension tue to ensure it is properly seted nd will not move during fn opertion. 11 Connect the wiring hrnesses. Secure the green ground wire from the extension tue to the supply ground wire nd the green ground wire on the mounting rcket. STEPS COMPLETED HAIKU HOME 51

12 Loop the sfety cle round the mounting rcket or uilding structure, nd then secure it with the shckle. Hrdwre:. Shckle 13 Rise the cnopy to the mounting rcket, lining up the four holes on the cnopy with the holes on the rcket. Secure the cnopy to the mounting rcket with the pinted screws. Mke sure no wires or the sfety cle re showing. Hrdwre:. M4 x 6 mm pinted screws INSTALLATION COMPLETED HAIKU HOME 53

6 TEST YOUR FAN Do not expose the remote control to rin or wter. Before using the remote control, remove the plstic t from the ttery try. Turn on power to the fn loction nd test functionlity using the remote. Turn on the fn nd test speed nd light rightness. If you purchsed the Hiku Wll Control, follow the instructions pckged with the wll control. For opertion, mintennce, nd trouleshooting informtion, visit hikuhome.com/help Turn on the fn Adjust fn speed Whoosh Sleep Turn on the light Adjust light Timer Cler 54 REV. D 2015 HAIKU HOME. ALL RIGHTS RESERVED.

2015 Hiku Home The informtion contined in this document is suject to chnge without notice. My e protected y one or more ptents listed t www.igsssolutions.com/ptents Hiku is trdemrk of Delt T Corportion, registered in the U.S. nd/or other countries. www.hikuhome.com/wrrnties

I HKU-INST-99-ENG-01