INSTALLATION INSTRUCTIONS Accessory Application Publications No. Bll 30250 UNDER SPOILER 2006 RSX Issue Date JULY 2005 PARTS LIST Rear under spoiler 5 Stepped bolts 2 Bolts 7 Flange nuts, 6 mm 3 Square bolts TOOLS AND SUPPLIES REQUIRED Phillips screwdriver Flat-tip screwdriver Combination wrench (10 mm) Ratchet 8 mm and 10 mm Sockets Drill (3 mm, 5 mm, and 10 mm bits) Blanket Hack saw Push pin Felt-tip pen File Isopropyl alcohol Shop towel Adhesive tape Eye protection (face shield, safety goggles, etc.) INSTALLATION Customer Information: The information in this installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your vehicle. These procedures should not be attempted by do-it-yourselfers. NOTE: 3 Flange nuts, 4 mm Be careful not to damage the rear bumper and body paint finish. To prevent damage to the bumper, set it on a blanket or cardboard during the installation. Template The rear under spoiler cannot be installed on a vehicle equipped with accessory splash guards. 2005 American Honda Motor Co., Inc - All Rights Reserved. BII 30250 (0507) 08F03-S6M-2000-9A 1 of 6
1. Open the trunk hatch. Remove the six self-tapping screws and two clips from the rear bumper. 4. Attach the template to the arched section of the rear bumper on the outer surface, and secure the template with strips of tape. LICENSE PLATE Align with the mark. CENTER OF THE MARK 65 mm FELT-TIP PEN Mark along the line on the inner side of the rib. TAPE TEMPLATE ARCHED SECTION OF 4511062Y SELF- TAPPING SCREWS (6) VEHICLE CONNECTOR CLIP 4224030Y 5. Mark the rear bumper with the cut line along the inner line of the template. 2. Lower the rear bumper slightly to release the license plate from the two hooks and rotate the license plate up. 3. With the help of an assistant, pull the rear bumper toward you, unplug the vehicle connector and remove the rear bumper. Do not damage the rear bumper or vehicle body when removing the rear bumper. 6. Remove the template. Using a hacksaw, cut the rear bumper along the cut line you just made. Remove any burrs from the edges of the cut section. CUT LINE Cut out. 4511070Y 2 of 6 BII 30250 (0507) 2005 American Honda Motor Co., Inc - All Rights Reserved.
7. Inside the bumper, locate the 3 marks. Using a pushpin, pierce the upper marks (do not use the 3 lower marks). While wearing eye protection, drill the 3 marked points with a 5 mm bit, then with a 10 mm bit. Using a file, remove any burrs from the edges of the holes. 9. Position the rear under spoiler on the rear bumper and loosely install five stepped bolts and five flange nuts. FELT-TIP PEN MARKS (3) Do not drill BRACKET STEPPED BOLTS (5) UNDER SPOILER DRILL (3 mm 5 mm BIT) PUSH PIN 8. Position the rear bumper upside down. Using a pushpin, pierce the rear bumper at the five points shown. While wearing eye protection, drill the five marked points with a 5 mm bit, then with a 10 mm bit. Using a file, remove any burrs from the edges of the holes. PUSH PIN DRILL (5 mm 10 mm BIT) 4304063Y FLANGE NUTS (5) 4511043Y 10. Using a felt-tip pen, mark the rear bumper (at two points) through the center of the bracket hole on the right and left sides of the rear under spoiler. 11. Remove the rear under spoiler from the rear bumper. 12. Using a pushpin, pierce at the two marks. While wearing eye protection, drill the two marked points with a 5 mm bit, then with a 10 mm bit. Using a file, remove any burrs from the edges around the holes. MARK (5) PUSH PIN DRILL (5 mm 10 mm BIT) Do not drill. CENTER OF THE MARK 4511031Y MARK Do not drill MARK 4511052Y 2005 American Honda Motor Co., Inc - All Rights Reserved. BII 30250 (0507) 3 of 6
13. Slide the three square bolts onto the rear under spoiler. ADHESIVE BACKING Attach a piece of adhesive tape to the ends of the adhesive backing, fold the ends up and tape them to the front side. 15. Insert the four self-tapping screws (two on each end) in the holes, and hold them in place with adhesive tape. SQUARE BOLT (3) Insert three square bolts in the holes first. SELF- TAPPING SCREW (4) BOLTS (2) UNDER SPOILER STEPPED BOLTS (5) SQUARE BOLT UNDER SPOILER 4 mm FLANGE NUTS (3) 4305011Y 14. Attach a piece of adhesive tape to the end of each adhesive backing on the inner side of the rear under spoiler. Fold the ends of the adhesive backings and temporarily tape them to the top surface of the rear under spoiler. 6 mm FLANGE NUTS (7) 4305022Y 16. Position the rear under spoiler on the rear bumper while aligning the holes for the bolts and nuts. Install the five stepped bolts, two bolts, seven 6 mm flange nuts and three 4 mm flange nuts. 4 of 6 BII 30250 (0507) 2005 American Honda Motor Co., Inc - All Rights Reserved.
17. Remove the adhesive tape from the screws installed in step 15, and install the screws. SELF- TAPPING SCREW (Reuse.) ADHESIVE BACKING Press firmly while removing the adhesive backings. Press. Press. 18. Securely reinstall the rear bumper with the six self-tapping screws and two clips. 19. Press the rear under spoiler against the rear bumper firmly while carefully removing the adhesive backings. 4305031Y 2005 American Honda Motor Co., Inc - All Rights Reserved. BII 30250 (0507) 5 of 6
Give a copy of this page to your customer Before towing this vehicle, follow the instructions described in the vehicle Owner s Manual. Before using the towing hook, make sure you remove both the rear bumper and rear under spoiler. Failure to follow this precaution can damage the rear bumper, rear under spoiler and vehicle. Your vehicle may look different from this illustration. 2912070W 6 of 6 BII 30250 (0507) 2005 American Honda Motor Co., Inc - All Rights Reserved.