echnical data sheet LHK24A-SZ Modulating SuperCap linear actuator with emergency setting function and extended functionalities for adjusting air dampers and sliders in ventilation and air-conditioning systems for building services installations and in laboratories For air dampers up to approx. m 2 Actuating force 5 N Nominal voltage AC/DC 24 V Control: Modulating DC... V Position osition feedback feedbac DC... V Height of stroke up to max. mm, adjustable in 2 mm increments Design life SuperCaps 5 years echnical data Electrical data Nominal voltage AC 24 V, 5/6 Hz / DC 24 V Nominal voltage range AC 9.2... 28.8 V / DC 2.6... 28.8 V Power consumption In operation At rest For wire sizing 7 W @ nominal torque 3 W 4 VA (l max 2 A @ 5 ms) Connection Cable m, 4 x.75 mm 2 Functional data Actuating force Inhibiting force 5 N 5 N Control Control signal Y Operating range DC V, input impedance k DC.5... V Position feedback (Measuring voltage U) DC.5... V, max..5 ma Emergency setting position (POP)... %, adjustable (POP rotary button) of the maximum height of stroke Bridging time with electricity interruption 2 s Position accuracy ±5% Direction of stroke Motor Emergency setting position Reversible with switch / Reversible with switch... % (retracted %) For Y = V At switch position or, respectively Manual override Gearing latch disengaged with push button Stroke adjustment max. mm, adjustable in 2 mm increments, can be limited at both ends with mechanical end stops Running time Motor Emergency setting function 2 s / mm 35 s @... 5 C Sound power level Motor Emergency setting function 45 db (A) @ 2 s running time 65 db (A) Safety Protection class III Safety extra-low voltage UL Class 2 Supply Degree of protection IP54 NEMA 2, UL Enclosure ype 2 EMC CE according to 24/8/EC Certification Certified to IEC/EN 673- and IEC/EN 673-2-4 culus according to UL 673-A and UL 673-2-4 and CAN/CSA E673-:2 Mode of operation ype.aa Rated impulse voltage.8 kv Control pollution degree 3 Ambient temperature 3... +5 C Non-operating temperature 4... +8 C Ambient humidity 95% r.h., non-condensating Maintenance Maintenance-free Dimensions / Weight Dimensions See «Dimensions» on page 6 Weight Approx.. kg. erms and abbreviations POP = Power off position / emergency setting position PF = Power fail delay time / bridging time www.belimo.com 2-LHK24A-SZ en v. 4.22 Subject to changes / 6
LHK24A-SZ function, AC/DC 24 V, 5 N, operating range DC... V Safety notes Product features! Mode of operation he actuator is not allowed to be used outside the specified field of application, especially in aircraft or in any other airborne means of transport. It may only be installed by suitably trained personnel. Any legal regulations or regulations issued by authorities must be observed during installation. he device may only be opened at the manufacturer's site. It does not contain any parts that can be replaced or repaired by the user. he cable must not be removed from the device. he rotary supports and coupling pieces available as accessories must always be used if lateral forces are likely. In addition, the actuator must not be tightly bolted to the application. It must remain movable via the rotary support (refer to «Assembly notes»). If a rotary support and/or coupling piece is used, then actuation force losses are to be expected. If the linear actuator is exposed to severely contaminated ambient air, appropriate precautions must be taken on the system side. Excessive deposits of dust, soot etc. can prevent the gear rod from being extended and retracted correctly. If not installed horizontally, the gear disengagement push button may only be actuated when there is no pressure on the gear rod. o calculate the actuating force required for air dampers and sliders, the specifications supplied by the damper manufacturers concerning the surface, cross-section, design, installation site and the air flow conditions must be observed. he device contains electrical and electronic components and is not allowed to be disposed of as household refuse. All locally valid regulations and requirements must be observed. he actuator moves the air damper to the desired operating position at the same time as the integrated capacitors are loaded. Interrupting the supply voltage causes the air damper to be set to the selected emergency setting position (POP) by means of stored electrical energy. he actuator is connected with a standard modulating signal of DC... V and travels to the position defined by the positioning signal. he measuring voltage U serves for the electrical display of the damper position... %. Pre-charging time (start up) he capacitor actuators require a pre-charging time. his time is used for charging the capacitors up to a usable voltage level. his ensures that, in the event of a voltage interruption, the actuator can be moved at any time from its current position into the preset emergency setting position (POP). he duration of the pre-charging time depends mainly on how long the power was interrupted. ypical pre-charging times 3 3 25 25 Pre-charging time [s] Duration of voltage interruption [Days] 2 7 6 9 6 2 Pre-charging time [s] 2 5 5 2 5 5 2 4 6 8 2 Duration of voltage interruption [Days] 2 / 6 2-LHK24A-SZ en v. 4.22 Subject to changes www.belimo.com
LHK24A-SZ Product features Delivery condition (capacitors) Simple direct mounting Manual override High functional reliability Home position / Start Direction of stroke switch Emergency setting position (POP) rotary button Adjustable stroke function, AC/DC 24 V, 5 N, operating range DC... V (continued) he actuator is completely discharged after delivery from the factory, which is why the actuator requires approximately 2 s pre-charging time before initial commissioning in order to bring the capacitors up to the required voltage level. he actuator can be directly connected with the application using the enclosed screws. he head of the gear rod is connected to the moving part of the ventilation application individually on the mounting side or with the Z-KS2 coupling piece provided. Manual override with push button possible (the gear is disengaged for as long as the button remains pressed down). he actuator is overload-proof, requires no limit switches and automatically stops when the end stop is reached. After the supply voltage has been switched on, the actuator moves into the position defined by the positioning signal. Pos. direction of stroke Y = Y = Home position extended retracted When actuated, the direction of stroke switch changes the running direction in normal operation. he direction of stroke switch has no influence on the emergency setting position (POP) which has been set. he «Emergency setting position» rotary button can be used to adjust the desired emergency setting position (POP). he POP range is in reference to the maximum height of stroke of the actuator. In the event of a voltage interruption, the actuator will move into the selected emergency setting position, taking into account the bridging time (PF) of 2 s which was set ex-works. he stroke range can be adjusted on both sides in increments of 2 mm by means of mechanical end stops. A minimum permissible stroke of about 2 mm must be allowed for when using external end stops. Accessories Description Data sheet Electrical accessories Positioner SGA24, SGE24 and SGF24 2 - SG..24 Digital position indicator ZAD24 2 - ZAD24 Room temperature controller CR24.. S4 - CR24-.. Mechanical accessories Rotary support to compensate lateral forces Z-DS 2 - Z-LH..A.. Coupling piece Z-KS2 2 - Z-LH..A.. End stop set Z-AS2 2 - Z-LH..A.. www.belimo.com 2-LHK24A-SZ en v. 4.22 Subject to changes 3 / 6
LHK24A-SZ function, AC/DC 24 V, 5 N, operating range DC... V Electrical installation Wiring diagram + Note Y Control signal Connect via safety isolation transformer.! U Measuring voltage 2 3 5 Cable colours: = black 2 = red 3 = white 5 = orange Wiring diagram for parallel operation + Y U U 2 U X Information A maximum of eight actuators can be connected in parallel. Parallel operation is permitted only on separated axes. It is imperative that the performance data be observed with parallel operation. 2 3 5 2 3 5 2 3 5 Actuator Actuator 2 Actuator X Cable lengths Y U C A = Actuator C = Control unit L = Belimo connecting cable, m (4 x.75 mm 2 ) L 2 = Customer cable L tot = Maximum cable length L 2 Note When several actuators are connected in parallel, the maximum cable length must be divided by the number of actuators. 2 3 5 L L tot A Cross-section L 2 / Max. cable length L tot = L + L 2 AC DC Example for DC.75 mm 2 4 m 2 m m (L ) + 9 m (L 2 ). mm 2 5 m 3 m m (L ) + 29 m (L 2 ).5 mm 2 8 m 45 m m (L ) + 44 m (L 2 ) 2.5 mm 2 3 m 8 m m (L ) + 79 m (L 2 ) N L AC 23 V AC 24 V Y U C A = Actuator C = Control unit L = Belimo connecting cable, m (4 x.75 mm 2 ) Note here are no special restrictions on installation if the supply and data cable are routed separately. 2 3 5 L A 4 / 6 2-LHK24A-SZ en v. 4.22 Subject to changes www.belimo.com
LHK24A-SZ function, AC/DC 24 V, 5 N, operating range DC... V Operating controls and indicators 7 2.9.5 3 POP. 4 Direction of stroke switch 2 Cover, POP button 3 POP button 4 Scale for manual adjustment 8 Status 6 (no function) 7 Disengagement button 6 LED display 8 green Illuminated Blinking Off Meaning / function Operation OK / without fault POP function active Not in operation Pre-charging time SuperCap Fault SuperCap. Setting the POP Power off position.5.5 POP.9..9. Status.9.5..9.5. POP %... www.belimo.com 2-LHK24A-SZ en v. 4.22 Subject to changes 5 / 6
LHK24A-SZ Assembly notes Application without lateral forces Application with lateral forces Caution If a rotary support and/or coupling piece is! used, losses in the actuation force losses are to be expected. Stroke limitation function, AC/DC 24 V, 5 N, operating range DC... V he linear actuator is screwed directly to the housing at three points. Afterwards, the head of the gear rod is fastened to the moving part of the ventilation application (e.g. damper or slider). he coupling piece with the internal thread (Z-KS2) is connected to the head of the gear rod. he rotary support (Z-DS) is screwed to the ventilation application. Afterwards, the linear actuator is screwed to the previously mounted rotary support with the enclosed screw. Afterwards, the coupling piece, which is mounted to the head of the gear rod, is attached to the moving part of the ventilation application (e.g. damper or slider). he lateral forces can be compensated for to a certain limit with the rotary support and/or coupling piece. he maximum permissible swivel angle of the rotary support and coupling piece is, laterally and upwards. If the stroke limitations are used on the gear rod, the mechanical working range can be exploited from an extension length of 2 mm. Dimensions [mm] Dimensional drawings 28 86 5 234 65 99 55 4 6 / 6 2-LHK24A-SZ en v. 4.22 Subject to changes www.belimo.com