Automotive Data Solutions Inc. INSTALL GUIDE ADS-AL(DL)-NI8-EN AVAILABLE FOR : ADS-AL CA Rev. Date: August 29, 2018 Doc. No.: ##52817## NI8 U.S. PATENT NO. 8,856,780 PLEASE VISIT WWW.IDATALINK.COM FOR COMPLETE PRODUCT DETAILS The brand names and logos found in this guide are property of their respective owners. Automotive Data Solutions Inc. 2018 TERMS OF USE: automotive Data solutions Inc. ( ads ) products are strictly intended for installation by Certified technicians who are employed by a registered business specialized in the installation of automotive aftermarket electronics products. Prior to beginning installation of an ads product in a vehicle, it is the Certified technician s responsibility to review the most current Product Guide, Install Guide and vehicle-specific notes available in Weblink. ads is not responsible for any damages whatsoever, including but not limited to any consequential damages, incidental damages, damages for loss of time, loss of earnings, loss of profit, commercial loss, loss of economic opportunity and the like that may or may not have resulted from the use, misuse, improper installation or operation of its products. ads reserves itself the right to suspend any Weblink account without notice and decline to offer technical support to non- Certified technicians, non-compliant Certified technicians or end users.
Page 2 of 14 ADS-AL(DL)-NI8-EN Doc. No.: ##52817## 20180829 INSTALL TYPE SELECTION features Make MoDel NOTE I On the remote starter, configure the feature LOCK AFTER SHUTDOWN, to control RAP/autolight shutdown. Year InStall type Data IMMoBIlIZer BYPaSS SecUre takeover a/m alarm ctrl from oem remotes a/m rs ctrl from oem remotes PUSH to Start ctrl Door StatUS output trunk StatUS output Brake PeDal StatUS output tachometer output e-brake output HaZarD light ctrl Qashqai PTS AT 17-18 2 nissan Rogue PTS AT 14-16 1 Rogue PTS AT 17 2 Rogue PTS AT 18 3 Rogue Sport PTS AT 17-18 2 InfInItI QX50 PTS AT 19 4
Page 3 of 14 ADS-AL(DL)-NI8-EN Doc. No.: ##52817## 20180829 COMPONENT LOCATOR A B
Page 4 of 14 ADS-AL(DL)-NI8-EN Doc. No.: ##52817## 20180829 TYPE 1 - WIRE CROSS REFERENCE CHART - 1 OF 1 Make MoDel Year DeScrIPtIon name type PoSItIon nissan PolarItY MoDUle location component locator CanH OBDII White 16 pin 06 Blue (DATA) At OBDII B CanL OBDII White 16 pin 14 Pink (DATA) At OBDII B PTS M19 Black 40 pin 09 Yellow (-) At BCM A Ignition OBDII White 16 pin 08 Yellow (+) At OBDII B 12V OBDII White 16 pin 16 White (+) At OBDII B Rogue PTS AT 14-16 Unlock M19 Black 40 pin 13 Pink (-) At BCM A Lock M19 Black 40 pin 12 Brown (-) At BCM A Power Liftgate ~ Green 08 pin 06 LtGreen (-) At switch, on lower dash panel A Ground OBDII White 16 pin 04 Black (-) At OBDII B Negative Starter E29 Black 24 pin 19 Green (-) At BCM A Negative Ignition 1 M18 Gray 40 pin 27 Yellow (-) At BCM A Negative Ignition 2 M18 Gray 40 pin 28 LtPurple/White or Green/White (-) At BCM A Negative Ignition 3 M18 Gray 40 pin 25 Brown (-) At BCM A
Page 5 of 14 ADS-AL(DL)-NI8-EN Doc. No.: ##52817## 20180829 TYPE 1 - WIRING DIAGRAM - 1 OF 1 4 3 2 8 7 6 1 5 POWER LIFTGATE (-) POWER LIFTGATE CONNECTOR LTGREEN (LOWER DASH PANEL) REMOTE STARTER OBDII CONNECTOR LOCATED UNDER DRIVER SIDE DASH 1 2 3 4 5 6 7 8 9 CANL GROUND (-) 10 11 12 13 14 15 16 12V (+) CANH IGNITION (+) TRUNK (-) OUTPUT TACH (AC) INPUT E-BRAKE STATUS (-) INPUT STARTER (+) OUTPUT UNLOCK (-) OUTPUT <- OPTIONAL LOCK (-) OUTPUT <- OPTIONAL 12V (+) GROUND (-) GROUND WHEN RUNNING (-) OUTPUT LEGEND NOT REQUIRED IN (1-WAY) NOT REQUIRED IN (2-WAY) REQUIRED -> GROUND (-) INPUT REQUIRED -> 12V (+) INPUT REQUIRED -> BRAKE STATUS (+) INPUT REQUIRED -> IGNITION (+) OUTPUT TRUNK STATUS (-) INPUT DOOR STATUS (-) INPUT WARNING: DO NOT CONNECT ANY OTHER ACCESSORY, IGNITION OR START WIRE FROM THE REMOTE STARTER TO THE VEHICLE USE OR HARDWIRE MODE OEM REMOTE REMAINS FUNCTIONAL DURING REMOTE START SEQUENCE GWR (-) INPUT - BLUE/WHITE (NC) WHITE GROUND - BLACK 12V (+) - RED LOCK (-) INPUT - GREEN/BLACK UNLOCK/DISARM (-) INPUT - BLUE/BLACK (NC) RED/WHITE (NC) BROWN (NC) PURPLE/YELLOW (NC) PURPLE/BLACK (NC) WHITE STARTER (+) INPUT - BLACK/WHITE E-BRAKE STATUS (-) OUTPUT - GREEN TACH (AC) OUTPUT - PURPLE/WHITE WHITE/BLACK - IGNITION (-) OUTPUT WHITE/RED (NC) WHITE - GROUND (-) INPUT YELLOW/BLACK - DOOR STATUS (-) OUTPUT YELLOW/RED - TRUNK STATUS (-) OUTPUT YELLOW (NC) BROWN/RED - CANH BROWN/YELLOW - CANL ORANGE/BLACK - PTS (-) OUTPUT ORANGE/WHITE (NC) ORANGE - BRAKE STATUS (+) OUTPUT PINK/BLACK (NC) PINK - IGNITION (+) INPUT BLUE/RED - GROUND (-) INPUT BLUE/YELLOW - STARTER (-) OUTPUT GREEN/RED (NC) GREEN/YELLOW (NC) GRAY/RED (NC) GRAY/YELLOW (NC) LOCK (-) UNLOCK (-) PTS (-) M19 - BLACK 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 31 30 29 28 27 26 25 24 23 M18 - GRAY 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 31 30 29 28 27 26 25 24 23 E29 - BLACK IGNITION 1 (-) IGNITION 2 (-) IGNITION 3 (-) 12 11 10 9 8 7 6 5 4 3 2 1 24 23 20 19 18 17 16 15 14 13 STARTER (-) BCM
Page 6 of 14 ADS-AL(DL)-NI8-EN Doc. No.: ##52817## 20180829 TYPE 2 - WIRE CROSS REFERENCE CHART - 1 OF 1 Make MoDel Year DeScrIPtIon name type PoSItIon nissan PolarItY MoDUle location component locator Qashqai PTS AT Rogue PTS AT Rogue Sport PTS AT 17-18 17 17-18 CanH ~ Green 40 pin 20 Blue (DATA) At BCM A CanL ~ Green 40 pin 40 Pink (DATA) At BCM A PTS M19 Black 40 pin 09 Red (-) At BCM A Ignition OBDII White 16 pin 08 Yellow (+) At OBDII B 12V OBDII White 16 pin 16 White (+) At OBDII B Unlock M19 Black 40 pin 13 Pink (-) At BCM A Lock M19 Black 40 pin 12 Brown (-) At BCM A Power Liftgate ~ Green 08 pin 06 LtGreen (-) At switch, on lower dash panel A Ground OBDII White 16 pin 04 Black (-) At OBDII B Negative Starter E29 Black 24 pin 19 Blue (-) At BCM A Negative Ignition 1 M18 Gray 40 pin 27 White/Green (-) At BCM A Negative Ignition 2 M18 Gray 40 pin 28 White/Blue (-) At BCM A Negative Ignition 3 M18 Gray 40 pin 25 White/Pink (-) At BCM A CanH ~ Green 40 pin 20 Blue (DATA) At BCM A CanL ~ Green 40 pin 40 Pink (DATA) At BCM A PTS M19 Black 40 pin 09 Yellow (-) At BCM A Ignition OBDII White 16 pin 08 Yellow (+) At OBDII B 12V OBDII White 16 pin 16 White (+) At OBDII B Unlock M19 Black 40 pin 13 Pink (-) At BCM A Lock M19 Black 40 pin 12 Brown (-) At BCM A Power Liftgate ~ Green 08 pin 06 LtGreen (-) At switch, on lower dash panel A Ground OBDII White 16 pin 04 Black (-) At OBDII B Negative Starter E29 Black 24 pin 19 Green (-) At BCM A Negative Ignition 1 M18 Gray 40 pin 27 Yellow (-) At BCM A Negative Ignition 2 M18 Gray 40 pin 28 LtPurple/White or Green/White (-) At BCM A Negative Ignition 3 M18 Gray 40 pin 25 Brown (-) At BCM A CanH ~ Green 40 pin 20 Blue (DATA) At BCM A CanL ~ Green 40 pin 40 Pink (DATA) At BCM A PTS M19 Black 40 pin 09 Red (-) At BCM A Ignition OBDII White 16 pin 08 Yellow (+) At OBDII B 12V OBDII White 16 pin 16 White (+) At OBDII B Unlock M19 Black 40 pin 13 Pink (-) At BCM A Lock M19 Black 40 pin 12 Brown (-) At BCM A Power Liftgate ~ Green 08 pin 06 LtGreen (-) At switch, on lower dash panel A Ground OBDII White 16 pin 04 Black (-) At OBDII B Negative Starter E29 Black 24 pin 19 Blue (-) At BCM A Negative Ignition 1 M18 Gray 40 pin 27 White/Green (-) At BCM A Negative Ignition 2 M18 Gray 40 pin 28 White/Blue (-) At BCM A Negative Ignition 3 M18 Gray 40 pin 25 White/Pink (-) At BCM A
Page 7 of 14 ADS-AL(DL)-NI8-EN Doc. No.: ##52817## 20180829 TYPE 2 - WIRING DIAGRAM - 1 OF 1 4 3 2 8 7 6 1 5 POWER LIFTGATE (-) POWER LIFTGATE CONNECTOR LTGREEN (LOWER DASH PANEL) OBDII CONNECTOR LOCATED UNDER DRIVER SIDE DASH 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 12V (+) IGNITION (+) REMOTE STARTER GROUND (-) TRUNK (-) OUTPUT TACH (AC) INPUT E-BRAKE STATUS (-) INPUT STARTER (+) OUTPUT UNLOCK (-) OUTPUT <- OPTIONAL LOCK (-) OUTPUT <- OPTIONAL 12V (+) GROUND (-) GROUND WHEN RUNNING (-) OUTPUT LEGEND NOT REQUIRED IN (1-WAY) NOT REQUIRED IN (2-WAY) REQUIRED -> GROUND (-) INPUT REQUIRED -> 12V (+) INPUT REQUIRED -> BRAKE STATUS (+) INPUT REQUIRED -> IGNITION (+) OUTPUT TRUNK STATUS (-) INPUT DOOR STATUS (-) INPUT WARNING: DO NOT CONNECT ANY OTHER ACCESSORY, IGNITION OR START WIRE FROM THE REMOTE STARTER TO THE VEHICLE USE OR HARDWIRE MODE OEM REMOTE REMAINS FUNCTIONAL DURING REMOTE START SEQUENCE GWR (-) INPUT - BLUE/WHITE (NC) WHITE GROUND - BLACK 12V (+) - RED LOCK (-) INPUT - GREEN/BLACK UNLOCK/DISARM (-) INPUT - BLUE/BLACK (NC) RED/WHITE (NC) BROWN (NC) PURPLE/YELLOW (NC) PURPLE/BLACK (NC) WHITE STARTER (+) INPUT - BLACK/WHITE E-BRAKE STATUS (-) OUTPUT - GREEN TACH (AC) OUTPUT - PURPLE/WHITE WHITE/BLACK - IGNITION (-) OUTPUT WHITE/RED (NC) WHITE - GROUND (-) INPUT YELLOW/BLACK - DOOR STATUS (-) OUTPUT YELLOW/RED - TRUNK STATUS (-) OUTPUT YELLOW (NC) BROWN/RED - CANH BROWN/YELLOW - CANL ORANGE/BLACK - PTS (-) OUTPUT ORANGE/WHITE (NC) ORANGE - BRAKE STATUS (+) OUTPUT PINK/BLACK (NC) PINK - IGNITION (+) INPUT BLUE/RED - GROUND (-) INPUT BLUE/YELLOW - STARTER (-) OUTPUT GREEN/RED (NC) GREEN/YELLOW (NC) GRAY/RED (NC) GRAY/YELLOW (NC) PTS (-) M18 - GRAY LOCK (-) UNLOCK (-) M19 - BLACK 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 31 30 29 28 27 26 25 24 23 31 30 29 28 27 26 25 24 23 IGNITION 1 (-) IGNITION 2 (-) IGNITION 3 (-) GREEN 12 11 10 9 8 7 6 5 4 3 2 1 24 23 20 19 18 17 16 15 14 13 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 E29 - BLACK CANL CANH BCM STARTER (-)
Page 8 of 14 ADS-AL(DL)-NI8-EN Doc. No.: ##52817## 20180829 TYPE 3 - WIRE CROSS REFERENCE CHART - 1 OF 1 Make MoDel Year DeScrIPtIon name type PoSItIon nissan PolarItY MoDUle location component locator CanH ~ Green 40 pin 20 Blue (DATA) At BCM A CanL ~ Green 40 pin 40 Pink (DATA) At BCM A PTS M19 Black 40 pin 09 Yellow (-) At BCM A Ignition OBDII White 16 pin 08 Yellow (+) At OBDII B 12V OBDII White 16 pin 16 White (+) At OBDII B Rogue PTS AT 18 Unlock M19 Black 40 pin 13 Pink (-) At BCM A Lock M19 Black 40 pin 12 Brown (-) At BCM A Power Liftgate ~ Green 08 pin 06 LtGreen (-) At switch, on lower dash panel A Ground OBDII White 16 pin 04 Black (-) At OBDII B Negative Starter E29 Black 24 pin 19 Green (-) At BCM A Negative Ignition 1 M18 Gray 40 pin 27 Yellow (-) At BCM A Negative Ignition 2 M18 Gray 40 pin 28 LtPurple/White or Green/White (-) At BCM A Negative Ignition 3 M18 Gray 40 pin 25 Brown (-) At BCM A
Page 9 of 14 ADS-AL(DL)-NI8-EN Doc. No.: ##52817## 20180829 TYPE 3 - WIRING DIAGRAM - 1 OF 1 4 3 2 8 7 6 1 5 POWER LIFTGATE (-) POWER LIFTGATE CONNECTOR LTGREEN (LOWER DASH PANEL) OBDII CONNECTOR LOCATED UNDER DRIVER SIDE DASH 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 12V (+) IGNITION (+) REMOTE STARTER GROUND (-) TRUNK (-) OUTPUT TACH (AC) INPUT E-BRAKE STATUS (-) INPUT STARTER (+) OUTPUT UNLOCK (-) OUTPUT <- OPTIONAL LOCK (-) OUTPUT <- OPTIONAL 12V (+) GROUND (-) GROUND WHEN RUNNING (-) OUTPUT LEGEND NOT REQUIRED IN (1-WAY) NOT REQUIRED IN (2-WAY) REQUIRED -> GROUND (-) INPUT REQUIRED -> 12V (+) INPUT REQUIRED -> BRAKE STATUS (+) INPUT REQUIRED -> IGNITION (+) OUTPUT TRUNK STATUS (-) INPUT DOOR STATUS (-) INPUT WARNING: DO NOT CONNECT ANY OTHER ACCESSORY, IGNITION OR START WIRE FROM THE REMOTE STARTER TO THE VEHICLE USE OR HARDWIRE MODE OEM REMOTE REMAINS FUNCTIONAL DURING REMOTE START SEQUENCE GWR (-) INPUT - BLUE/WHITE (NC) WHITE GROUND - BLACK 12V (+) - RED LOCK (-) INPUT - GREEN/BLACK UNLOCK/DISARM (-) INPUT - BLUE/BLACK (NC) RED/WHITE (NC) BROWN (NC) PURPLE/YELLOW (NC) PURPLE/BLACK (NC) WHITE STARTER (+) INPUT - BLACK/WHITE E-BRAKE STATUS (-) OUTPUT - GREEN TACH (AC) OUTPUT - PURPLE/WHITE WHITE/BLACK - IGNITION (-) OUTPUT WHITE/RED (NC) WHITE - GROUND (-) INPUT YELLOW/BLACK - DOOR STATUS (-) OUTPUT YELLOW/RED - TRUNK STATUS (-) OUTPUT YELLOW (NC) BROWN/RED - CANH BROWN/YELLOW - CANL ORANGE/BLACK - PTS (-) OUTPUT ORANGE/WHITE (NC) ORANGE - BRAKE STATUS (+) OUTPUT PINK/BLACK (NC) PINK - IGNITION (+) INPUT BLUE/RED - GROUND (-) INPUT BLUE/YELLOW - STARTER (-) OUTPUT GREEN/RED (NC) GREEN/YELLOW (NC) GRAY/RED (NC) GRAY/YELLOW (NC) PTS (-) M18 - GRAY LOCK (-) UNLOCK (-) M19 - BLACK 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 31 30 29 28 27 26 25 24 23 31 30 29 28 27 26 25 24 23 IGNITION 1 (-) IGNITION 2 (-) IGNITION 3 (-) GREEN 12 11 10 9 8 7 6 5 4 3 2 1 24 23 20 19 18 17 16 15 14 13 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 E29 - BLACK CANL CANH BCM STARTER (-)
Page 10 of 14 ADS-AL(DL)-NI8-EN Doc. No.: ##52817## 20180829 TYPE 4 - WIRE CROSS REFERENCE CHART - 1 OF 1 Make MoDel Year DeScrIPtIon name type PoSItIon PolarItY InfInItI MoDUle location component locator CanH ~ Green 40 pin 20 Blue (DATA) BCM A CanL ~ Green 40 pin 40 Pink (DATA) BCM A PTS M19 Black 40 pin 09 Yellow (-) BCM A Ignition OBDII White 16 pin 08 White (+) OBDII B 12V OBDII White 16 pin 16 Yellow (+) OBDII B Unlock M19 Black 40 pin 21 Pink (-) BCM A QX50 PTS AT 19 Lock M19 Black 40 pin 01 Brown (-) BCM A Power Liftgate ~ White 16 pin 04 White (-) At switch, on lower dash panel A Ground OBDII White 16 pin 04 Black (-) OBDII B Negative Starter E29 Black 24 pin 19 Green (-) BCM A Negative Ignition 1 M18 Gray 40 pin 27 Yellow (-) BCM A Negative Ignition 2 M18 Gray 40 pin 28 White (-) BCM A Negative Ignition 3 M18 Gray 40 pin 25 Brown (-) BCM A Driver Door Pin ~ Green 40 pin 17 LtBlue (-) BCM A Hazard M18 Gray 40 pin 11 Yellow (-) BCM A
Page 11 of 14 ADS-AL(DL)-NI8-EN Doc. No.: ##52817## 20180829 TYPE 4 - WIRING DIAGRAM - 1 OF 1 8 7 6 5 4 3 2 1 16 15 14 13 12 11 10 9 POWER LIFTGATE (-) POWER LIFTGATE CONNECTOR WHITE REMOTE STARTER OBDII CONNECTOR LOCATED UNDER DRIVER SIDE DASH 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 GROUND (-) 12V (+) IGNITION (+) TRUNK (-) OUTPUT TACH (AC) INPUT E-BRAKE STATUS (-) INPUT STARTER (+) OUTPUT UNLOCK (-) OUTPUT <- OPTIONAL LOCK (-) OUTPUT <- OPTIONAL PARKING LIGHT (+) OUTPUT <- OPTIONAL 12V (+) GROUND (-) GROUND WHEN RUNNING (-) OUTPUT LEGEND NOT REQUIRED IN (1-WAY) NOT REQUIRED IN (2-WAY) IMPORTANT: NO TAKEOVER AVAILABLE. ENGINE WILL SHUTDOWN UPON UNLOCK. REQUIRED -> GROUND (-) INPUT REQUIRED -> 12V (+) INPUT REQUIRED -> BRAKE STATUS (+) INPUT REQUIRED -> IGNITION (+) OUTPUT TRUNK STATUS (-) INPUT DOOR STATUS (-) INPUT WARNING: DO NOT CONNECT ANY OTHER ACCESSORY, IGNITION OR START WIRE FROM THE REMOTE STARTER TO THE VEHICLE USE OR HARDWIRE MODE OEM REMOTE REMAINS FUNCTIONAL DURING REMOTE START SEQUENCE GWR (-) INPUT - BLUE/WHITE (NC) WHITE GROUND - BLACK 12V (+) - RED LOCK (-) INPUT - GREEN/BLACK UNLOCK/DISARM (-) INPUT - BLUE/BLACK (NC) RED/WHITE (NC) BROWN (NC) PURPLE/YELLOW (NC) PURPLE/BLACK PARKING LIGHT (+) INPUT - WHITE STARTER (+) INPUT - BLACK/WHITE E-BRAKE STATUS (-) OUTPUT - GREEN TACH (AC) OUTPUT - PURPLE/WHITE WHITE/BLACK - IGNITION (-) OUTPUT WHITE/RED (NC) WHITE - GROUND (-) INPUT YELLOW/BLACK - DOOR STATUS (-) OUTPUT YELLOW/RED - TRUNK STATUS (-) OUTPUT YELLOW - RAP SHUTDOWN (-) OUTPUT BROWN/RED - CANH BROWN/YELLOW - CANL ORANGE/BLACK - PTS (-) OUTPUT ORANGE/WHITE - HAZARD (-) OUTPUT ORANGE - BRAKE STATUS (+) OUTPUT PINK/BLACK (NC) PINK - IGNITION (+) INPUT BLUE/RED - GROUND (-) INPUT BLUE/YELLOW - STARTER (-) OUTPUT GREEN/RED (NC) GREEN/YELLOW (NC) GRAY/RED (NC) GRAY/YELLOW (NC) LOCK (-) UNLOCK (-) HAZARD (-) M18 - GRAY M19 - BLACK 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 31 30 29 28 27 26 25 24 23 31 30 29 28 27 26 25 24 23 PTS (-) GREEN IGNITION 1 (-) IGNITION 2 (-) IGNITION 3 (-) E29 - BLACK 12 11 10 9 8 7 6 5 4 3 2 1 24 23 20 19 18 17 16 15 14 13 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 CANL CANH DRIVER DOOR PIN STARTER (-) BCM
Page 12 of 14 ADS-AL(DL)-NI8-EN Doc. No.: ##52817## 20180829 INSTALLATION MODE SELECTION 1 Press and release programming button to select installation mode. 2 Press and hold programming button until LED turns solid GREEN to register selection. LED flashes (1X) once = LED flashes (2X) twice = STANDARD HARDWIRE MODE! After registration, follow Factory Reset Procedure to change installation mode and restart this procedure. MODULE PROGRAMMING PROCEDURE 1 OFF ACC ON START Set ignition to ON position. 8 WARNING: Disconnect power last. Disconnect module from vehicle. ENGINE START ÆÆ STOP 2 Wait, LED will turn solid RED, then solid GREEN for 1 second, then solid RED. 9 Æ Connect module to computer and proceed with extended programming. 3 OFF ACC ON START ENGINE START STOP Set ignition to OFF position. 10 Æ WARNING: Connect power first. Connect module to vehicle. 4 Wait, LED will turn OFF. 11 OFF ACC ON START Set ignition to ON position. ENGINE START STOP 5 OFF ACC ON START ENGINE START Set ignition to ON position. 12 Wait, LED will turn solid GREEN for 2 seconds. STOP 6 If LED flashes GREEN rapidly, proceed with step 7. If LED turns solid GREEN for 2 seconds, proceed with step 13. 13 OFF ACC ON START ENGINE START STOP Set ignition to OFF position. 7 OFF ACC ON START Set ignition to OFF position. 14 Module Programming Procedure completed. ENGINE START STOP
Page 13 of 14 ADS-AL(DL)-NI8-EN Doc. No.: ##52817## 20180829 IDENTIFY VEHICLE YEAR 1 Locate the Vehicle Identification Number (VIN), identify the 10th character then match it to its corresponding year. Æ 4 3 A 5 Y 1 N 5 T A L 8 D 5 R 0 X Æ a 1980 l 1990 Y 2000 a 2010 B 1981 M 1991 1 2001 B 2011 c 1982 n 1992 2 2002 c 2012 D 1983 P 1993 3 2003 D 2013 e 1984 r 1994 4 2004 e 2014 f 1985 S 1995 5 2005 f 2015 G 1986 t 1996 6 2006 G 2016 H 1987 V 1997 7 2007 H 2017 J 1988 W 1998 8 2008 J 2018 k 1989 X 1999 9 2009 k 2019 led StatUS Flashing RED DIaGnoStIcS DUrInG ProGraMMInG DUrInG remote Start WItH IGnItIon off Missing/wrong information from firmware or vehicle Incorrectly programmed Solid RED Waiting for more vehicle information Incorrectly programmed Flashing GREEN Additional steps required to complete programming MODULE DIAGNOSTICS Correctly programmed and operational Incorrectly programmed or connected Not programmed waiting for more vehicle information False ground when running status from remote starter Solid GREEN then OFF Correctly programmed Reset in progress Reset in progress OFF No activity or already programmed Invalid ground when running status from remote starter At rest and ready for a remote start sequence FACTORY RESET PROCEDURE 1 2 DISCONNECT all s from module EXCEPT the black 4-PIN standard or optional data. DISCONNECT black 4-PIN standard or optional data. 5 6 LED will turn solid red for 2 seconds. RESET COMPLETED. RECONNECT all s. 3 PRESS AND HOLD programming button while connecting either 4-PIN standard or optional data. 7! Repeat programming procedure. Failure to follow procedure may result with a DTC or a CHECK ENGINE error message. 4 When LED flashes red, RELEASE programming button.
IMPORTANT Page 14 of 14 ADS-AL(DL)-NI8-EN Doc. No.: ##52817## 20180829 WARNING: READ BEFORE REMOTE NOTICESTARTING THE VEHICLE I All vehicle doors must be closed and locked prior to remote start sequence. Failure to comply will result in remote starter malfunction. TAKE OVER PROCEDURE - PUSH TO START - TO THE VEHICLE OWNER NOTE I È All vehicle doors must be closed and locked prior to remote start sequence. TIME RESTRICTIºN COMING UP! 2 TIME RESTRICTIºN Within 45 SECONDS from previous step: Open vehicle door. Enter vehicle. Close vehicle door. Press and release BRAKE pedal. 1 Unlock vehicle door using OEM or after-market remote, or door request switch. 3 Take over procedure completed.! Failure to follow procedure will result in vehicle engine shutdown.