Simba K102 production drill rig Hydraulic production drill rig for long-hole mining 1
Get into your tunnel The simple and practical Simba k102 is a long-hole production drill rig for small to medium-drift mining, medium-to-large holes ranging from 64 to 89 mm in diameterit accomodates a range of drill bits and rock drills to adapt to your specific needs, and brings both ring drilling and parallel drilling pattern withi range of width 1.5 Meters. Mobile carrier with FOPS certified roof provides easier tramming and safer environment for operator. Varied and robust positioning mechanism brings flexible and stable feeder position, and accurate drilling straightness. Maintenance-friendly design makes the service work safe and easy. All service points are reachable from ground level. Main benefits FOPS certified roof for added safety Safety Mobile control panel keeps operators away from drilling center and provides clear visibility for drilling factors. FOPS certified roof protects operator during tramming. Uncompromising design and manufacture for all devices. The main electrical cabinet is located on a high point to be well protected from moist and water 360 rotary device Small profile Optimized size with up-and-down FOPS roof, adjustable positioning system and articulated carrier guarantees the operation in small tunnel and easier for navigation. Stability and reliability The Simba K102 is built on a sturdy carrier with proven design and components. The mobile control panel is connected to the machine via cable, and the system provides easy and reliable trouble shooting. Angle reading system for accurate control Extensible leg for added stability Mobile control panel gives flexible position for operator Swingable rear shaft for reduced waggle 2 3
Support for trouble free operation Epiroc is always committed to sustainable productivity. We value the research and development with the innovation and inspiration to realize customer's first choise. + COP1238 rock drill of durability and reliability A standard Simba K102 is equipped with a COP 1238K rock drill. It is developed to maximize impact power while optimizing durability. COP 1238K is designed for reliable and trouble-free operation. Its long and slender piston matched to the drill steel permits optimal impact power without damaging the drill steel. Built in damper contributes to improved drill steel economy and reduces wear on rock drill, feed and boom. It has separate lubrication of front-head and driver together with pressurized and lubricated mating surfaces and side-bolts for the best protection against wear and corrosion. + BMH 6000 series feed of ultimate reliability The BMH 6000 series feed is strong and rigid aluminum beam with extremely high resistance against bending and torsion stresses, which is able to reduce drill steel costs and ensures straighter holes. It is equipped with stainless steel bushing which protects the feed from wearing. The feed force can reach maximum 20 kn and make the machine drill faster. Wear pieces on all sliding surfaces protect major components and reduces maintenance costs. Accurate guidance of cradles ensures maximum service life for shank adapter and drill steel, and straighter holes. A comprehensive service offering Even the best equipment needs to be serviced regularly to make sure it sustains peak performance. An Epiroc service solution offers peace of mind, maximizing availability and performance throughout the lifetime of your equipment. We focus on safety, productivity and reliability. By combining genuine parts and an Epiroc service from our certified technicians, we safeguard your productivity wherever you are. COP 1238K COP 1838 + Shank adapter T38 / T45 T38 / T45 Hole diameter 64-76 mm 64-89 mm Max. impact power 15 kw 18 kw Impact rate 50 Hz 60 Hz Hydraulic pressure 220 bar 230 bar Rotation motor 07/09 Separate rotation Rotation speed 0-210 rpm / 0-140 rpm 0-340 rpm /0-215 rpm Rotation torque, max 1 000 Nm / 1 550 Nm 640 / 1 000 Nm Lub. air consump. at 2 bar 6 l/s 5 l/s Weight 172 kg 170 kg Feed BMH 6000-series BMH 6X03R BMH 6X04R Total length 2 744 mm 3 049 mm Drill rod length 915 mm 1 220 mm Positioning system Feed extension (with 915 mm and 1220 mm drill steel)...900 mm Drill steel support... BSH45 Rotary Actuator BHR 30 for 360º ring drilling Pendulum arm, BHP 12 gives 1.5 m feed parallel positioning in the side walls Stinger backward on feed Stinger forward on feed Feed dump, drilling... +20º forward and -80º backward Control system Electrical Direct System, EDS 12 Basic functions such as anti-jamming included Powerpack Hydraulic pump for percussion, positioning, feed Hydraulic pump for rotation Pumps unloaded at start System pressure, max... 230 bar Hydraulic oil tank, volume... 124 L Low oil level indicator and shut-down Oil temperature gauge on oil tank, electronically supervised Filtration, absolute... 16 μm Oil filter indicator Water cooled oil cooler in stainless steel Mineral hydraulic oil Electric system Total installed power... 55 / 65 kw Main motor... 45 / 55 kw Voltage... 380 / 1 000 V Frequency... 50 Hz Starting method... star/delta (380V ) / direct (1 000 V) Thermal overload protection for electric motors Percussion hour meters on A-panel Digital volt/amperage meter in electric cabinet Phase sequence indicator Earth fault indicator Battery charger Transformer... 5 kva Working lights on tripods... 2x200 W, 24 V Cable reel, inner/outer diameter... ø 660/1095 mm Limit switch for cable reel Air system Compressor...Atlas Copco LE7 Capacity at 5400 rpm and 7 bar...12 L/s Air pressure gauge Water system Electric water booster pump Capacity at 10 bar boost... max 100 L/min Min water inlet pressure... 2 bar Water pressure gauge Carrier Engine... Deutz TCD3.6 L4, China Stage III Power rating at 2300 rpm...55.4 kw Torque at 1300 rpm...... 390 Nm Fixed seat for tramming, including safety belt Articulated steering... ±40 steering angle Four-wheel drift FOPS-approved protective roof Hydrostatic power steering system Front axle... DANA 112 Rear axle... DANA 112, ±10º oscillation Automatic differential lock on front axle, limited slip Tyres... 8.25x15 Clearance outside axles... 15º Hydraulic jacks, front... 2 extendable Hydraulic jacks, rear... 2 Service brakes.2 separate circuits (hydraulically applied, fully enclosed wet disc brakes) Emergency and parking brakes... SAHR Fuel tank, volume... 60 L Electric system... 24 V Batteries... 2x70 Ah Tramming lights... 8xLED Brake lights Central lubrication system Catalyser Silencer exhaust system Fire extinguisher Spirit levels Gradeability at max load on drift wheels... 1:4 Tramming speed on flat ground... >10 km/h Tramming speed on incline 1:8... >4 km/h Horn, beacon and reverse alarm 4 5
Optional equipment Measurements Side view Drill steel Hole diameter, mm Drill rod Shank adapter Guide tube COP 1238K 64-76 T38 Speedrod T38 56 / 64mm Dimension for a and b COP 1238K 76-89 T45 Speedrod T45 64 / 76mm BMH 6803R BMH 6804R COP 1838+ 64-76 T38 Speedrod T38 56 / 64mm A 2520 2573 COP 1838+ 76-89 T45 Speedrod T45 64 / 76mm B 2744 3049 20 Protective roof COP 1838+ with max. 18kW output power Working lights, HID 35W, 24V Double dampening system for optimized performance and drill Manual spotlight 700 150 steel economy 35 R2 Carrier 2 228 Electric system Voltage 1000V / 50 Hz Feed A lubrication surveillance system B Tramming lights, LED 40W, 24V Drill system Plug PC4 BMH 6X04R Socket PC4 Switch gear Control system Electric outlet, main supply voltage EDS18 Electrics according to local standards 2 161 1 350 1 350 1 476 6 916 Tramming length, no Pirra 7 168 Drilling platform Front view Turning radius mm Outer 5 171 Inner 2 850 750 Dimensions 750 mm 900 450 1500(PH) 45 45 Width 1 670 Height tramming (A) 2 520/2 573 Height roof up 2 928 Length 7 168 Ground clearance 260 Total 10 060 Weight 3000 Minimum drift height 1758 Max Rotation center to ground (PH) 6 Recommended cable size and length 800 1 500 1 670 Rb(RD) 800 Voltage Type Dimension, mm2 Diameter,mm Length,m 380 V Buflex 3x70+3G16 37 125 1 000 V Buflex 3x35+3G6 28 205 Recommendations are given for surrounding temperature of 40 C. and up to a height of 2000m. Rc(PH) Feed BMH 6303 R BMH 6804 R Note: PH - Parallel Holes RD - Ring Drilling Unit: mm Kg 1 380 1500 1 555 Rotation center to ground gross weight 3000 Minimum drift width Rb 1850 2155 Rc 1850 2155 7
9869 0028 01 2018-05 Nanjing, China. Legal Notice Copyright 2018, Epiroc (Nanjing) Mining & Construction Equipment Ltd., Nanjing, China. All product names in this publication are trademarks of Epiroc. Any unauthorized use or copying of the contents or any part thereof is prohibited. Illustrations and photos may show equipment with optional extras. No warranty is made regarding specifications or otherwise. Specifications and equipment are subject to change without notice. Consult your Epiroc Customer Center for specific information. United in performance. Inspired by innovation. Performance unites us, innovation inspires us, and commitment drives us to keep moving forward. Count on Epiroc to deliver the solutions you need to succeed today and the technology to lead tomorrow. epiroc.com