Alarms & Remote Start INSTALL GUIDE OEM-AL(RS)-CH0-[OL-MDB-ALL]-EN DOCUMENT NUMBER 990 REVISION DATE 008 FIRMWARE OEM-AL(RS)-CH0-[OL-MDB-ALL] HARDWARE OL-MDB-ALL ACCESSORIES OL-LOADER (REQUIRED) NOTICE The manufacturer will accept no responsability for any electrical damage resulting from improper installation of this product, be that either damage to the vehicle itself or to the installed device. This device must be installed by a certified technician. Please review the Installation Guide carefully before beginning any work. BEFORE INSTALLATION - Connect module to computer - Login to Weblink account - Flash firmware to module (module is not preloaded with firmware) - Use accessories accordingly (accessories are sold separately) Automotive Data Solutions Inc. 0
VEHICLE LIST - OF PAGE OF 9 DOC.: #990 008 FEATURES NOTE MAKE MODEL I II WARNING: All vehicle doors must be closed and locked prior to remote start sequence. Idle mode is not available. YEAR INSTALL TYPE DATA IMMOBILIZER BYPASS ARM OEM ALARM DISARM OEM ALARM DOOR LOCK DOOR UNLOCK PRIORITY UNLOCK TRUNK/HATCH RELEASE POWER LIFTGATE SECURE TAKEOVER DOOR STATUS OUTPUT TRUNK STATUS OUTPUT HOOD STATUS OUTPUT* E-BRAKE OUTPUT TACHOMETER OUTPUT BRAKE PEDAL STATUS OUTPUT PARKING LIGHT CTRL X LOCK START/STANDALONE MOD. TAKEOVER FROM DOOR HANDLES POWER SLIDING DOOR (L) POWER SLIDING DOOR (R) 00 PTS AT - CHRYSLER PACIFICA PTS AT 7 JEEP Cherokee PTS AT - *Available only if vehicle is equipped with factory hood switch. Automotive Data Solutions Inc. 0 OEM-AL(RS)-CH0-[OL-MDB-ALL]-EN
BOX CONTENTS - OF PAGE OF 9 DOC.: #990 008 BOX CONTENTS MODULE PIN WHITE CONNECTOR PIN BLACK CONNECTOR WHITE PROGRAMMING BUTTON LED 7 PIN WHITE CONNECTOR 0 PIN BLACK CONNECTOR WHITE WHITE 7 A B C F 0 9 8 7 BLACK PIN WHITE CONNECTOR DATA CABLE BLUE D E BLACK DATA PORT (WEBLINK, RF, TELEMATIC) PIN BLUE CONNECTOR DATA CABLE WEBLINK CABLE (required accessory sold separately) WEBLINK CABLE MODULE DATA PORT COMPUTER USB PORT PIN BLACK CABLE Automotive Data Solutions Inc. 0 OEM-AL(RS)-CH0-[OL-MDB-ALL]-EN
COMPONENT LOCATOR - OF PAGE OF 9 DOC.: #990 008 INTERIOR VIEW A B DRIVER SIDE VIEW PASSENGER SIDE VIEW Automotive Data Solutions Inc. 0 OEM-AL(RS)-CH0-[OL-MDB-ALL]-EN
TYPE - WIRE CHART - OF PAGE OF 9 DOC.: #990 008 MAKE MODEL YEAR WIRE DESCRIPTION CONNECTOR NAME CONNECTOR COLOR JEEP CONNECTOR TYPE POSITION WIRE COLOR POLARITY MODULE LOCATION COMPONENT LOCATOR V OBDII Black pin Red (+) Above driver kick panel B Cherokee PTS AT - Ground OBDII Black pin 0 Black (-) Above driver kick panel B CanH OBDII Black pin 0 Gray/White (DATA) Above driver kick panel B CanL OBDII Black pin Yellow (DATA) Above driver kick panel B Ignition/Start Control C8 Gray 0 pin 8 Pink/White (+) BCM driver side fusebox, rear view B Parking Lights DA Black 0 pin 0 White/Brown (MUX) Headlamp Switch A Automotive Data Solutions Inc. 0 OEM-AL(RS)-CH0-[OL-MDB-ALL]-EN
TYPE - WIRING DIAGRAM - OF PAGE OF 9 DOC.: #990 008 MODULE A : C8 BLACK BCM (REAR VIEW) WHITE B F C D E DATA A B C 7 0 GRAY/YELLOW (NC) 0 GRAY/RED (NC) 0 GREEN/YELLOW (NC) 0 GREEN/RED (NC) 0 BLUE/YELLOW (NC) 0 BLUE/RED (NC) 0 PINK (NC) 0 PINK/BLACK (NC) 0 ORANGE - IGNITION/START CONTROL (+) 0 ORANGE/WHITE (NC) 0 ORANGE/BLACK (NC) 0 BROWN/YELLOW - CANL 07 BROWN/RED - CANH 0 YELLOW (NC) 0 YELLOW/RED (NC) 0 YELLOW/BLACK (NC) 7. A IGNITION/START CONTROL (+) - 8 CANL - CANH - 0 GROUND (-) - 0 V (+) - 0 9 8 7 7 7 8 9 0 9 8 7 0 9 8 0 9 8 7 0 9 8 7 0 9 8 7 0 OBDII CONNECTOR D E 0 WHITE - GROUND (-) INPUT 0 WHITE/RED - PARKING LIGHT CONNECTOR SIDE 0 WHITE/BLACK - PARKING LIGHT VEHICLE SIDE 0-70 0HMS PARKING LIGHT (MUX) - 0 : DA BLACK HEADLAMP SWITCH 0 BLUE/WHITE (NC) 0 WHITE (NC) 0 BLACK - GROUND 0 RED - V (+) WITHOUT A COMPATIBLE ACCESSORY 7 8 9 0 OR DATA CABLE COMPATIBLE ACCESSORY WITH A COMPATIBLE ACCESSORY. IMPORTANT: SEE THE COMPATIBLE ACCESSORIES PAGE FOR DETAILS. F 7 8 9 0 0 GREEN/BLACK - HOOD STATUS (-) INPUT 0 BLUE/BLACK (NC) 0 RED/WHITE (NC) 0 BROWN (NC) 0 PURPLE/YELLOW (NC) 0 PURPLE/BLACK (NC) 07 WHITE (NC) 08 BLACK/WHITE (NC) 09 GREEN (NC) 0 PURPLE/WHITE (NC) WITHOUT OEM HOOD SWITCH: INSTALL AND CONNECT TO AFTERMARKET HOOD SWITCH AFTERMARKET HOOD SWITCH (-) Automotive Data Solutions Inc. 0 OEM-AL(RS)-CH0-[OL-MDB-ALL]-EN
TYPE - WIRE CHART - OF PAGE 7 OF 9 DOC.: #990 008 MAKE MODEL YEAR WIRE DESCRIPTION CONNECTOR NAME CONNECTOR COLOR CRHYSLER CONNECTOR TYPE POSITION WIRE COLOR POLARITY MODULE LOCATION COMPONENT LOCATOR V OBDII Black pin Red (+) Above driver kick panel B 00 PTS AT - Ground OBDII Black pin 0 Black (-) Above driver kick panel B CanH OBDII Black pin 0 Gray/White (DATA) Above driver kick panel B CanL OBDII Black pin Yellow (DATA) Above driver kick panel B Ignition/Start Control I0 Black 9 pin 0 Pink/White (+) Junction connector, above driver kick panel, front of fuse box B Parking Lights DA Black 0 pin 0 White/Brown (MUX) Headlamp Switch A Automotive Data Solutions Inc. 0 OEM-AL(RS)-CH0-[OL-MDB-ALL]-EN
TYPE - WIRING DIAGRAM - OF PAGE 8 OF 9 DOC.: #990 008 MODULE JUNCTION CONNECTOR, ABOVE DRIVER KICK PANEL, FRONT OF FUSE BOX A B F C D E DATA A 0 GRAY/YELLOW (NC) 0 GRAY/RED (NC) 0 GREEN/YELLOW (NC) 0 GREEN/RED (NC) 0 BLUE/YELLOW (NC) 0 BLUE/RED (NC) IGNITION/START CONTROL (+) - 0 : I0 BLACK 7 8 9 0 7 8 9 7 0 8 9 0 7 8 9 0 7 8 9 0 7 8 9 B C 7 0 PINK (NC) 0 PINK/BLACK (NC) 0 ORANGE - IGNITION/START CONTROL (+) 0 ORANGE/WHITE (NC) 0 ORANGE/BLACK (NC) 0 BROWN/YELLOW - CANL 07 BROWN/RED - CANH 0 YELLOW (NC) 0 YELLOW/RED (NC) 0 YELLOW/BLACK (NC) 7. A CANL - CANH - 0 GROUND (-) - 0 V (+) - OBDII CONNECTOR 7 8 9 0 D E 0 WHITE - GROUND (-) INPUT 0 WHITE/RED - PARKING LIGHT CONNECTOR SIDE 0 WHITE/BLACK - PARKING LIGHT VEHICLE SIDE 0-70 0HMS PARKING LIGHT (MUX) - 0 : DA BLACK HEADLAMP SWITCH 0 BLUE/WHITE (NC) 0 WHITE (NC) 0 BLACK - GROUND 0 RED - V (+) WITHOUT A COMPATIBLE ACCESSORY 7 8 9 0 OR DATA CABLE COMPATIBLE ACCESSORY WITH A COMPATIBLE ACCESSORY. IMPORTANT: SEE THE COMPATIBLE ACCESSORIES PAGE FOR DETAILS. F 7 8 9 0 0 GREEN/BLACK - HOOD STATUS (-) INPUT 0 BLUE/BLACK (NC) 0 RED/WHITE (NC) 0 BROWN (NC) 0 PURPLE/YELLOW (NC) 0 PURPLE/BLACK (NC) 07 WHITE (NC) 08 BLACK/WHITE (NC) 09 GREEN (NC) 0 PURPLE/WHITE (NC) WITHOUT OEM HOOD SWITCH: INSTALL AND CONNECT TO AFTERMARKET HOOD SWITCH AFTERMARKET HOOD SWITCH (-) Automotive Data Solutions Inc. 0 OEM-AL(RS)-CH0-[OL-MDB-ALL]-EN
TYPE - WIRE CHART - OF PAGE 9 OF 9 DOC.: #990 008 MAKE MODEL YEAR WIRE DESCRIPTION CONNECTOR NAME CONNECTOR COLOR CRHYSLER CONNECTOR TYPE POSITION WIRE COLOR POLARITY MODULE LOCATION COMPONENT LOCATOR V OBDII Black pin Red (+) Above driver kick panel B Pacifica PTS AT 7 Ground OBDII Black pin 0 Black (-) Above driver kick panel B CanH OBDII Black pin 0 Gray/White (DATA) Above driver kick panel B CanL OBDII Black pin Yellow (DATA) Above driver kick panel B Ignition/Start Control C Black/Gray 8 pin 7 Pink/White (+) BCM, Driver side dash, front view B Parking Lights ~ Black/Gray 0 pin 0 White/Brown (MUX) Headlamp Switch A Automotive Data Solutions Inc. 0 OEM-AL(RS)-CH0-[OL-MDB-ALL]-EN
TYPE - WIRING DIAGRAM - OF PAGE 0 OF 9 DOC.: #990 008 MODULE BCM, DRIVER SIDE DASH, FRONT VIEW A B F C D E DATA A B C 7 0 GRAY/YELLOW (NC) 0 GRAY/RED (NC) 0 GREEN/YELLOW (NC) 0 GREEN/RED (NC) 0 BLUE/YELLOW (NC) 0 BLUE/RED (NC) 0 PINK (NC) 0 PINK/BLACK (NC) 0 ORANGE - IGNITION/START CONTROL (+) 0 ORANGE/WHITE (NC) 0 ORANGE/BLACK (NC) 0 BROWN/YELLOW - CANL 07 BROWN/RED - CANH 0 YELLOW (NC) 0 YELLOW/RED (NC) 0 YELLOW/BLACK (NC) 7. A IGNITION/START CONTROL (+) - 7 CANL - CANH - 0 GROUND (-) - 0 V (+) - : BLACK/GRAY 9 7 0 8 9 0 7 8 9 0 7 8 7 7 9 8 8 0 OBDII CONNECTOR 7 8 9 0 D E 0 WHITE - GROUND (-) INPUT 0 WHITE/RED - PARKING LIGHT CONNECTOR SIDE 0 WHITE/BLACK - PARKING LIGHT VEHICLE SIDE 0-70 0HMS PARKING LIGHT (MUX) - 0 : DA BLACK HEADLAMP SWITCH 0 BLUE/WHITE (NC) 0 WHITE (NC) 0 BLACK - GROUND 0 RED - V (+) WITHOUT A COMPATIBLE ACCESSORY 7 8 9 0 OR DATA CABLE COMPATIBLE ACCESSORY WITH A COMPATIBLE ACCESSORY. IMPORTANT: SEE THE COMPATIBLE ACCESSORIES PAGE FOR DETAILS. F 7 8 9 0 0 GREEN/BLACK - HOOD STATUS (-) INPUT 0 BLUE/BLACK (NC) 0 RED/WHITE (NC) 0 BROWN (NC) 0 PURPLE/YELLOW (NC) 0 PURPLE/BLACK (NC) 07 WHITE (NC) 08 BLACK/WHITE (NC) 09 GREEN (NC) 0 PURPLE/WHITE (NC) WITHOUT OEM HOOD SWITCH: INSTALL AND CONNECT TO AFTERMARKET HOOD SWITCH AFTERMARKET HOOD SWITCH (-) Automotive Data Solutions Inc. 0 OEM-AL(RS)-CH0-[OL-MDB-ALL]-EN
MODULE PROGRAMMING PROCEDURE - OF PAGE OF 9 DOC.: #990 008 0 Close driver door. Re-open driver door to wake up data bus. 07 WARNING: Disconnect power last. Disconnect module from vehicle. Module Programming Procedure completed. 0 Press Unlock on keyfob. 08 Connect module to computer and proceed with extended programming. 0 Wait, LED will flash GREEN once [x]. 09 WARNING: DO NOT press programming button. Connect power first. Connect module to vehicle. 0 STOP ACC ON START Push start button twice [x] to START position. 0 Close driver door. Re-open driver door to wake up data bus. ENGINE START STOP 0 Within 0 seconds, LED will flash GREEN rapidly. STOP ACC ON START Push start button twice [x] to START position. ENGINE START STOP 0 STOP ACC ON START Push start button once [x] to OFF position. Wait, LED will turn solid GREEN for seconds. ENGINE START STOP Automotive Data Solutions Inc. 0 OEM-AL(RS)-CH0-[OL-MDB-ALL]-EN
VALET MODE PROGRAMMING PROCEDURE - OF PAGE OF 9 DOC.: #990 008 >> NOTE: In Valet Mode, the Remote starter is not functional. Keyless entry, Lock and Unlock will remain functional. See RF kit user manual for alternate valet mode programming. >> To exit valet mode: repeat steps to. 0 Time restriction. Complete next step within 7 seconds. 0 OFF ACC ON START Cycle ignition ON five times [x OFF/ON] rapidly. ENGINE START STOP 0 Wait, LED will turn solid RED for seconds. 0 OFF ACC ON START Set ignition to OFF position. ENGINE START STOP 0 Valet Mode Programming Procedure completed. Automotive Data Solutions Inc. 0 OEM-AL(RS)-CH0-[OL-MDB-ALL]-EN
PAGE OF 9 DOC.: #990 008 MODULE NAVIGATION PROCEDURE - OF >> It is mandatory to exit the Module Navigation at the end of this procedure. Failure to exit the Module Navigation will drain vehicle battery. To exit the Module Navigation at any time: Follow STEP. 0 >> Module must be programmed to the vehicle. 0 >> Use the Module Navigation Chart on the next page. 0 Set ignition to OFF position. 07 TO ACCESS THE MENUS: Press and hold programming button until LED turns solid GREEN. 08 IN THE MENUS: Press the programming button as many times as the menu number indicates. LED will flash GREEN an equal amount of times continuously. 09 0 OFF ACC ON START TO ACCESS THE OPTIONS: Press and hold programming button until LED turns solid RED. 0 IN THE OPTIONS: Press the programming button as many times as the option number indicates. LED will flash RED an equal amount of times continuously. TO ACCESS THE SETTINGS: Press and hold programming button until LED turns solid GREEN. Configure every other setting and proceed to step. [Z] LED will flash GREEN as many times as the current (or default) setting number, continuously. MANDATORY: EXIT MODULE NAVIGATION. Press and hold programming button for 7 seconds. LED will flash RED rapidly. Release programming button. LED will turn OFF. [Z] IN THE SETTINGS: Press the programming button as many times as necessary to access your setting. LED will flash GREEN an equal amount of times continuously. Module navigation completed. To return to the MENUS: exit the Module Navigation and redo the Module Navigation Procedure. >> Failure to exit the Module Navigation will drain vehicle battery. [Y] To save and return to the OPTIONS: Press and hold programming button until LED turns solid RED. [Y] LED will flash RED as many times as the current option number continuously. ENGINE START STOP 0 0 [X] Automotive Data Solutions Inc. 0 OEM-AL(RS)-CH0-[OL-MDB-ALL]-EN
MODULE NAVIGATION CHART - OF PAGE OF 9 DOC.: #990 008 MODULE NAVIGATION CHART: NOTES [X] MENUS [Y] OPTIONS [Z] SETTINGS I II Default settings are listed in bold. Make sure the option is covered on the vehicle before attempting to change the setting. *Vehicle will shutdown when a door is opened. 0 DISARM/UNLOCK BEFORE START 0 OFF 0 ON 0 RELOCK AFTER START 0 OFF 0 ON 0 RELOCK AFTER SHUTDOWN 0 OFF 0 ON 0 FORCE UNLOCK ALL ON FIRST PRESS 0 OFF 0 ON 0 TAKEOVER 0 ENABLE 0 DISABLE* 0 SEC 0 SECURE TAKEOVER DELAY 0 90 SEC 0 0 MIN 0 0 MIN 07 N/A 0 N/A 0 CONFIGURATION 0 0 MIN 0 0 MIN 0 0 MIN 08 MODULE RUN TIME 0 MIN 0 MIN 0 0 MIN 07 MIN 08 MIN 0 0 SEC 0 0 SEC 0 08 SEC 09 WAIT TO START DELAY 0 0 SEC 0 SEC 0 0 SEC 07 SEC 08 0 SEC 0- N/A 0 N/A 0-07 Technical Support only 0 N/A 0 N/A Automotive Data Solutions Inc. 0 OEM-AL(RS)-CH0-[OL-MDB-ALL]-EN
REMOTE STARTER ERROR CODES - OF PAGE OF 9 DOC.: #990 008 REMOTE STARTER ERROR CODES: NOTES [X] NUMBER OF PARKING LIGHT FLASHES DIAGNOSTIC I II WARNING: The following applies only when the parking lights are connected and supported by the system. After a remote starter failure, the parking lights will flash [X] number times to indicate an error code. See table. 0 Foot brake is ON. 0 Hood is open. 0 Engine tach signal is lost. 0 System is in Valet Mode. 07 Vehicle is moving (VSS). 08 Glow plug timeout error. Automotive Data Solutions Inc. 0 OEM-AL(RS)-CH0-[OL-MDB-ALL]-EN
MODULE DIAGNOSTICS - OF PAGE OF 9 DOC.: #990 008 TEST MODULE LED STATUS DIAGNOSTIC I II III DURING PROGRAMMING DURING REMOTE START WITH IGNITION OFF Flashing RED Solid RED Flashing GREEN Solid GREEN then OFF OFF Flashing RED Solid RED Flashing GREEN Solid GREEN then OFF OFF Flashing RED Solid RED Flashing GREEN Solid GREEN then OFF OFF Missing/wrong information from firmware or vehicle. Module waiting for more vehicle information. Additional steps required to complete module programming. Module correctly programmed. No activity or module already programmed. Module incorrectly programmed. Module incorrectly programmed. Module correctly programmed and operational. Reset in progress. Invalid ground when running status from remote starter. Module incorrectly programmed or connected. Module not programmed. Waiting for more vehicle information. False ground when running status from remote starter. Reset in progress. Module at rest and ready for a remote start sequence. Automotive Data Solutions Inc. 0 OEM-AL(RS)-CH0-[OL-MDB-ALL]-EN
MODULE RESET PROCEDURE - OF PAGE 7 OF 9 DOC.: #990 008 0 Disconnect all connectors from module except the BLACK -PIN connector. 07 Reconnect all connectors. 0 Disconnect the BLACK -PIN connector. 08 Repeat programming procedure. 0 PRESS AND HOLD programming button while connecting the BLACK -PIN connector. >> Failure to follow procedure may result with a DTC or a CHECK ENGINE error message. 0 Wait, LED will flash RED. RELEASE programming button. 0 LED will turn RED for seconds. 0 Module RESET completed. Automotive Data Solutions Inc. 0 OEM-AL(RS)-CH0-[OL-MDB-ALL]-EN
TAKEOVER PROCEDURE - OF PAGE 8 OF 9 DOC.: #990 008 >> All vehicle doors must be closed and locked prior to remote start sequence. 0 Press and release BRAKE pedal. 0 Time restriction. Complete steps to within seconds. 07 Take over procedure completed. 0 Press unlock on OEM or aftermarket remote or request switch. >> Failure to follow procedure will result in vehicle engine shutdown. 0 Open driver door and enter vehicle. 0 Close driver door. 0 STOP ACC ON START ENGINE START STOP Push the start button twice [x] AND wait for the following message to disappear from the instrument cluster: Key fob has left the vehicle. Automotive Data Solutions Inc. 0 OEM-AL(RS)-CH0-[OL-MDB-ALL]-EN
INSTALLATION CHECKLIST - OF PAGE 9 OF 9 DOC.: #990 008 CHECKLIST WARNING: Vehicle engine will start many times. Test in a well ventilated area. Close all vehicle doors, hood and trunk. Press LOCK button three times [x] rapidly on the OEM keyfob to remote start vehicle. Question : Does the vehicle remote start? YES: Go to next step. NO: The module doesn't detect OEM remote lock button from the vehicle communication network. Check all connections, repeat the test and call technical support, if the problem persists. Press LOCK button three times [x] rapidly on the OEM keyfob to shut down vehicle. Question : Does the vehicle shut down? YES: Go to next step. NO: Repeat step. If the problem persists, press on the brake pedal once [x] to shut down the vehicle and call technical support. RAP Shutdown test Question : Did the radio, interior controls, and headlights turn off within 0 seconds after remote start shutdown? YES: Go to next step. NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support, if the problem persists. Open hood. 7 If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step. 8 Press LOCK button three times [x] rapidly on the OEM keyfob to remote start vehicle. Question : Does the vehicle remote start? YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test. NO: Go to next step. 9 Close hood. 0 Enter vehicle and close the doors. Press LOCK button three times [x] rapidly on the OEM keyfob to remote start vehicle. Wait for the vehicle to start. Press brake pedal. Question : Does the vehicle shut down? YES: Go to next step. NO: The module does NOT detect the brake pedal signal. Press LOCK button three times [x] rapidly on the OEM keyfob to shut down, check the brake connection as illustrated in the wiring diagram, if applicable, and call technical support. Exit vehicle. Installation checklist completed. Automotive Data Solutions Inc. 0 OEM-AL(RS)-CH0-[OL-MDB-ALL]-EN