Fast Clip & Traklok Jaw Options (Quick Change Jaws) Fastclip Clip up Jaws (standard on machine) Part No.: 1640146 28kg to 68kg/m Rail Fastclip Unclip jaw Jaws standard with Fastclip head 47-68 kg/m Rail, Standard Part No. 1640155 28-47 kg/m Rail Optional Part No. 1640156 Traklok B296 Steel Clip up Jaws Part No. 1640153 Upclip of Tracklok & Fastclip 1640155 Unclip of Fastclip 47kg to 68kg Rail (standard on machine) 1640156 Unclip of Fastclip 28kg to 47kg Rail 1640145 Unclip Traklok 47kg to 68kg rail 1640144 Unclip of Traklok 28kg to 47kg Rail Clippers I MELVELLE EQUIPMENT CORP 11/80
Fastclip Quick Change Jaws Retrofit Kit Change Jaws from clip to unclip in MINUTES, simply remove 3x pins per arm to changeover. Parts needed to convert existing machines to take the new style quick change jaws: Item Number Number Required Description Part Image 1640148 2 Clipping Arm 1640150 2 Unclip long bottom drive pin 1640152 2 Unclip centre support pin 1640151 4 Clip up short main drive pin 1640154 2 Centre quick change pin assembly PIN0604 10 Lynch Pin Choice of new style jaws: 1640146 2 FastClip Clip up Jaw (All rail sizes) 1640155 1640156 2 2 FastClip UnClip Jaw (47-68kg rail) FastClip UnClip Jaw (28-47kg rail) 1640153 2 Traklok B296 Steel Clip up Jaw 1640145 1640144 2 2 Traklok B296 Steel Unclip Jaw (47-68kg rail) Traklok B296 Steel Unclip Jaw (28-47kg rail) 12/80 Clippers I MELVELLE EQUIPMENT CORP
E- Clip/PR Clip Remover FP- 186 work head was specifically designed to remove E- Clips and PR Clips on both timber and concrete sleepers. This new design will remove the clips in standard track condition and difficult situations where the clips are frozen/rusted in. The E- Clip/PR Clip remover is the seventh hydraulic work head available for the Trackpack system. Features Machine weight counterbalanced for minimum operator effort attaches to a Trackpack or dedicated powerpack Under normal conditions unclips E/PR Clip on either side of one rail in approx 2-5 seconds Under Severe conditions unclips E/PR Clips on either side of one rail in approx 6-30 seconds Leaves E- Clips in parked position ready for reinsertion WH&S issues addressed by this hydraulic work head include: Removes the requirement of hitting clips with a hammer, preventing the following injuries: o Back Strain o Repetitive strain injury o Hammer strike to legs due to recoil from clip o Damage to feet through striking/or clips hitting ball of foot o Struck by flying clips or debris when not retained by Operator Dual trigger operation for safety Removes E- Clips Removes PR Clips Clippers I MELVELLE EQUIPMENT CORP 13/80
Drills Rotabroach Rail Drill Petrol Rotabroach Rail Drill Package includes: Rail Drill Coolant Bottle 5x 32mm Tungsten Carbide Tipped Cutters 2x Height Templates 41-47kg/m & 53-60kg/m 2x Hole Centre Locators 41-47kg/m & 53-60kg/m Lightweight Carry Case Quick Release Clamp Part No. FP- 112- RDPK- QC Complete with lightweight carrying case & coolant pump Highly portable with low noise level (average noise level during 81 dba) Robust and reliable Model Number RD074 / RD074HSQ Motor type Honda 4 stroke Displacement 49 / 51 Maximum hole cutting capacity 36mm dia No load speed 167rpm / 660rpm Height 420mm Overall dimensions Width 420mm Exc. bottle Length 540mm Net weight 18.5kgs Spindle bore 19.05 (3/4") Throttle activation Automatic with feed Safety features Clutch fitted 14/80 Drills I MELVELLE EQUIPMENT CORP
Rotabroach Rail Drill Electric Rotabroach Rail Drill Package includes: Part No. FP- 112- RDPK- E4160 Part No. FP- 112- RDPK- E68 Rail Drill Coolant Bottle 5x 32mm Tungsten Carbide Tipped Cutters Height Templates to suit Hole Centre Locator and base to suit Lightweight Carry Case Quick Release Clamp Complete with lightweight carrying case & coolant pump Highly portable with low noise level (average noise level during cutting 89 dba) Robust and reliable Model Number CM/127/1 / CM/127/3 Motor type 110V full load 11amps 1100 W 230V full load 5amps 1100W Displacement 49 / 51 Maximum hole cutting capacity 40mm dia No load speed 350-600rpm Height 265mm Overall dimensions Width 180mm Exc. bottle Length 510mm Net weight 16.2kgs Spindle bore 19.05 (3/4") Safety features Clutch and electronic overload Drills I MELVELLE EQUIPMENT CORP 15/80
Rotabroach Rail Drill Accessories Multi- form Templates The Rotabroach system eliminates the need for individual templates saving time and expense. To move from one rail form to another, operators only have to release the centre screw, turn the template to the appropriate position and locate it on the dowels before re- tightening. Part No.: 1120548 Height Template 31kg/m 1120387 Height Template 41-47kg/m 1120386 Height Template 53-60kg/m 1120881 Height Template 68kg/m Hole Centre Locators To ensure that the holes are correctly distanced from centre to centre, a hole centre location unit is available which fits on top of the rail and can quickly be secured by tightening two handles. Recesses in the plate are designed to accommodate the machine as it is lowered into position. These features provide complete accuracy when working in difficult and low light conditions. Part No.: 1120389 3 Hole Locator 41-47- 53kg/m 1120399 3 Hole Locator 50-60- 68kg/m 1120699 2 Hole Locator 50-60- 68kg/m 1120915 Hole Centre Locator for Insulated Rail Joints 68kg/m plus base 1120916 Quick Release Rail Clamp Fitted to all our rail machines is our new quick release rail clamp system. To enable you to easily remove the rail machine from the rail with a single movement of the release handle. Will save time when drilling multiple holes. Railway TCT & HSS Cutters designed to cut even the toughest of rail Available cutter sizes 18mm 36mm Most common sizes listed below M42 Solid twist drills available in any size Part No. Ømm Part No. Ømm Short Series Long Series RCTCT2525 25 RCHSSC2525 25 Rotabroach Pilot Pins Rotabroach Pilot Pins RCTCT2825 28 RCHSSC2825 28 Part No. Range Part No. Range RCTCT3025 30 RCHSSC3025 30 1120697 13-40mm 1120698 13-40mm RTCT3225 32 RCHSSC3225 32 Lubricants Description Part No. Coolant Concentrate 5L 1120685 Bio- Degradable Cutting Fluid 20L 1120941 Stick Lubricant RCSTICKLUB 16/80 Drills I MELVELLE EQUIPMENT CORP
Tanaka Sleeper and Bonding Drills Tanaka TED270- RS Sleeper Drill Part No. 1540116 Bonding Drill Engine Tanaka 2- Stroke Full Crank Displacement (cc) 27.0 Max hp 1.5 Max kw 1.1 Handle Type/s: Front 2- Position Adjustable (L or R) Rear Pistol Grip Clutch System Centrifugal Starter System Recoil - SmartStart SmartStart Standard Ignition Electronic Carburettor Walbro Diaphram with Primer Assist Muffler System Spark Arrestor Reduction Ratio 20:1 Chuck Size (mm/in) 12.5 / 1/2" (Standard) Max Chuck RPM at Engine RPM 0-450 / 9000 Maximum Drill Bit 1 1/2" (Soft Wood) 1" (Hard Wood) Fuel Tank Capacity (cc) 500 Weight (kg) 5.0 Optional Attachments: Tree Planting Bit See Accessories Keyed Chuck Part No. FP- 112-43 1.5hp Two- Stroke Engine features SmartStart Recoil - 50% less force required to start Two Piston Rings and a Stress Relieved, Chrome- plated Cylinder for Longer engine life Dual Position Front Handle - Left or Right for Operator Flexibility Portable and light- weight Drill anywhere - in any position - without the hassles of electrical cords, compressors, generators or battery rechargers Lever Activated Powered Reversing Feature ½ Inch Keyless Chuck accepts A wide variety of Wood, Steel, and Concrete bits No nonsense 2- stroke maintenance - Designed and Manufactured by Japan's Finest Engineers Security and peace of mind with Comprehensive Spare Parts Range available Tanaka Warranty provides One- Year Coverage for Professionals Five- Year Coverage for Homeowners Drills I MELVELLE EQUIPMENT CORP 17/80
Stihl BT 45 Sleeper Drill Lightweight, powerful wood boring drill, ideal for building or repairing docks and bulkheads, fences, outbuildings, retaining walls and other structures where electricity is not available. Technical Data Part No. 1540245 Model BT 45 Drill Displacement (cm 3 ) 27.2 Engine Power (kw) 0.75 Weight (kg) 4.8 Gear Speed 1 st (rpm) 910 Gear Speed 2 nd (rpm) 2,710 Gear Speed Reverse (rpm) 590 Fuel Petrol Features Petroleum powered engine lets you work in places without electrical power - cycle gasoline powered engine that Primer bulb and throttle lock for easy starting Easy access air filter Electronic ignition Exclusive tool less fuel cap Two- ringed piston Compact, streamlined ergonomic design makes it easy to operate Anti- vibration system for comfortable use Four function gearbox, with two forward speeds, neutral position as well as a reverse gear Friction clutch is designed to slip if bit stalls Balanced design with well- spaced handles Stihl BT121 Sleeper Drill Engine Technical Data Part No. FP- 112- AA Model BT 121 Drill Displacement (cm 3 ) 30.8 Engine Power (Kw) 1.3 Weight (kg) 12.5 Stroke (mm) 32 Bore (mm) 35 Fuel 2 Stroke Petrol Drilling Speed (Max) 700 rpm 18/80 Drills I MELVELLE EQUIPMENT CORP
Speed Borer for Timber Sleepers FP- 140/155 Part No. FP- 140- EY The unit has easy to change drill guides and bits, easy to adjust depth stops/apply lever assisted hand feed/ and drill depth stop. One of the necessities of a good drill is the ease in setting up the drill. The FP- 155 has full angle tilt in all directions via clamp on a ball mounting. The FP- 140 models are available in Honda petrol recoil start or Honda petrol/yanmar diesel electric start with centrifugal clutch. Dedicated Unit FP- 140 Trackpack Head FP- 155- AO Honda Yanmar Engine Petrol Diesel Maximum Drill Spindle 1200 rpm 1200 rpm Weight of Balance Beam 74kg 74kg Weight of Rail Trolley 30kg 30kg Approximate Time to Drill 2 Seconds 2 Seconds Max Height 1300 mm x 630 mm across the handles 1300 mm x 630 mm across the handles Drill Feed Travel 230 mm 230 mm Drills I MELVELLE EQUIPMENT CORP 19/80
Rail Grinder FP- 157 Grinders The Melvelle Equipment Grinder Diesel engine is modified in- house to operate at high tilt angles and give much greater torque under load than similar sized engines. Prior to despatch Rail Profile Grinders are supplied with a proven fast cut grinding wheel for maximum bite into the rail and a high cutting rate and fully tested. The grinder has wide set rail rollers to achieve the smoothest finish possible. Flange rollers assist in supporting the weight of the grinder when grinding the rail face. Model 157- CV 157- DD 157- DC 157- CK Yanmar Robin Source Diesel Hydraulic Electric Diesel Power (Hp) 4.7-5 5 Weight (kg) 75 57 79 79 Length (mm) 1100 1100 1100 1100 Width (mm) 600 600 600 600 Height (mm) 940 940 940 940 Conversion Kit Rail Grinder conversion kits are available to mount to numerous other brand grinder frames. The kit includes a converted Diesel engine, engine mount adaptor plate, adaptor shaft, pulley wheel and belt. The kit is supplied assembled and tested, ready for installation straight onto the existing frame. Conversion Model Model 157- CZ Engine Yanmar Fuel Diesel Power (Hp) 4.7 Weight (kg) 32 Diesel FP- 157- CV Yanmar Conversion Kit FP- 157- CZ Electric FP- 157- DC For Grinding Stones please refer to Rail Accessories 20/80 Grinders I MELVELLE EQUIPMENT CORP