Manual valves automatic meters and valves
Butterfly valves manual valves Advanced technical design 1. Robust and lightweight leverage system. Ergonomic design. Protection of gear mechanism.. Flange fitting actuators S/ISO 511.. Extended stem for thermal insulation of pipes.. Centre linear configuration ISO/DIN PN 10/ (adaptable ASA /). 5. Reinforced with synthetic resin rear seat. 6. Highly polished disc finishing for maximum water tightness and little scope for error. 7. Bidirectional patented packaging of superior and inferior axis to guarantee perfect bubble tight shutoff by PTFE retaining ring.. Reinforced with synthetic resin rear seat. 9. Standard painting with EPOXY covering. 10. Airtight sealing by PTFE ring. Axis protected against debris. 11. Air tight double security ring. 1. Reinforced rubber grooved flanged faces for improved air tightness in operation. 1. Pre-equipped for actuators and all types of accessories. Rating in stock: PN 5-00; PN10-0. Flange connection in stock: DIN PN /10 5-00; PN10 -N0. Other ratings and connections as per demand.
Butterfly valves Construction data and design Bidirectional valves with ALL / NONE shut-off or regulated opening in diverse positions. Construction design in accordance with EN 59, construction length as per DIN 0/ISO 575, series 0. Pressure rating: bar up to 00, 10 bar from. Maximum operating temperature: 10oC with EPDM seating; 15 o C with VITON seat; oc with NBR seat; tests according to DIN 0/ISO 50. WAFER type design for mounting between flanges DIN PN, PN 10 and ASA (ANSI B..5 lbs optional) or LUG for mounting between flanges DIN PN, PN 10, superior mounting for receiving actuators as per ISO 511. Standard materials: Body: cast iron GG 5 (EN-GJL-) with epoxy covering. Disc: thread cast GGG 0 (EN-GJL-00) with chrome / stainless steel AISI treatment. Axis: stainless steel. Elastic shut-offs. EPDM - other replacements available: VITON, NBR, HYPALON, SILICON. Cv values 0 00 00 0 10 o 0,0 0,06 0,10 0,0 0,0 0, 0, 6 11 1 0 o, 6 9 17 9 5 9 151 6 615 791 1. Pressure rating/ Temperature 0 o 5,6 7 1 6 61 0 715 9 1.0 1.67.57 Opening angle of disc 0 o 1 15 5 9 7 1 05 0 69 1.07 1.59.10..6 5.605 T P (bar) o 1,6 7 5 19 7 66 717 1.7 1.911.761.797 5.0 6. 9.99-10 o C 60 o 5, 75 1 0 9 605 1.0.07..56 6..0 10.69.5 0 o C o 56 119 6 60 1.,90.0 5.005 7.0 9.9 1..91 6.157 o 105 17 75 56 90 1.7.5.59 7.7 10. 1.91 19.75 5.96 9.6 10 o C 90 o 9 115 196 0 1.0 1.579. 5.0. 11.917. 1.5 7.90.1 10 o C 15, Types of activation Manual lever. Manual control by hand wheel. Simple pneumatic actuator. Double pneumatic actuator. Electric actuator. Control accessories Solenoid valves Final strokes Position selectors Principal applications Civil and Industrial acclimatisation (hot and refrigerated water), treatment of water, hydrocarbons, lubrication and transmission oils, air and general services.
Butterfly valves F Principal dimensions E A B ØC ØG Valves with lever activation. A B øc D E F øg m m m m m m m m 0 00 11 10,5 1 15 19 15 10 57 61 77 7,5 107 1 1 171 05 5 7 109 17 15 07 60 15 6 6 5 56 56 60 6 7 7 7 7 7 7 7 9 79 7 7 7 7 7 55 7 7 90 90 H A Valves with lever activation. F ØK E G D ØC Valves with manual control by hand wheel. A B øc D E F G m 0 00 00 0 m m m m m m m 11 10,5 1 15 19 15 10 7 57, 6, 6,5 57 61 77 7,5 107 1 1 171 05 5 5,5 0, 9 5 7 109 17 15 07 60 15 55 575 69 6 6 5 56 56 60 6 7 7 10 11 17 15 171 177,5 199 1 56 19,5 9,5 76,5 15, 7,9 97, 6 156 156 156 156 156 156 5 156 156 1 6 11 11 9 9 H m 1 1 1 1 1 1 19,5 9,5 9,5 9,5 07,9 57,9 øk m 00 00 00 00 00 00 00 00 B Valves with manual control by hand wheel. D Please consult our Technical Department for information about dimensions of valves with other types of activation (simple pneumatic, free axis, electric servomotor, pneumatic activated actuators with manual security command, hydraulic cylinders), as well as dimensions not specified here. Available range up to 0.
Double plated retention valves Dimensions The dimensions of the UNICHECK valves corresponding to the standard supplies program, according to the exterior diameter for fitting between flanges DIN 576, PN 10 are specified in the table below. Principal dimensions m 00 00 0 5 0 0 0 900 1.000 1.0 1. A B C D Peso (kg) m m m m 6 76 9 11 11 17 10 15 19 79 1 0 56 7 19 5 109 10 1 9 71 6 76 0 71 5 660 7 77 90 1.0 1. 1.19 1. 66 11 15 0 10 60 10 60 10 510 559 610 660 711 76 1 91 1.0 1.067 1.19 R9 R6 R R5 R R77 R10 R17 R15 R1 R0 R R6 R9 R1 R7 R R97 R0 R R57 R60 1,6 1,9,7, 6, 10,7 17,,7,0 71,0 99,0 59 579 5 0 0 1.000 1.0 1.60.055 Please contact our Technical Department for information about dimensions of a superior size. Materials and parts The standard configuration is based on a combination of materials adequate for general acclimatization services. Body Plates Seat body Spring Cast iron GG 5 (EN-GJL- DIN 19) Nodular cast with nickel plating EPDM o NBR Stainless steel Please contact our Technical Department for information about dimensions of a superior size. On request, the UNICHECK manufacturing program includes the supply of other materials for bodies and plates, as well as ICONEL springs so as to offer greater protection against wear and tear. Please contact our Technical Department for more details about supplies. Principal applications The principal applications of the standard supplies of UNICHECK valves are Ventilation, Air Conditioning, and Heating. With nitrile joints, they are used in factories for lubrication, mineral oils, industrial fats and other derivatives.
Flow charts and loss of charge Water charge loss in gallon metres (1.).000 660.000 0 (1.000) 6 (900) (0) 0 (7) () 0 (0) () (00) 1 () 1 (00) 10 ().000.000 0.000 0.000 1.000 0.000 1.000 5.000 10.000 0.000.000 15.000 66.000 10.000.000 5.000.000.000.0.0 0.000.000 17. 1. 11.000.0 () 6 () 5 () () ().5 () () 1.0 1.000 0 00 00 0 0 5 0 15 6..00. 1.760 1.0 1. 660 0 0 176 1 110 66 10 5 10 6 5 1 0. 0.6 0.5 0. 0. 0. 0.1 0.0 0.06 0.05 Water charge loss in gallon metres 0.0 0.0 0.0 0.01 Q (m /h) Q (USGPM) *The minimum charge loss for each valve is indicated by the intersection with a blue line. m 00 00 0 0 900 1.0 1. Cv 55 5 15 90 60 0 1.5.0. 5.. 10.5 1.0.000.000 6.000 91.000.000 mmaq 00 00 10 10 10 10 60 0 5 0 The charge loss to the action of the spring is in relation to the normal torque. The Cv is the number of USA gallons per minute which results in a pressure loss of 1 Psi through the valve with 5 0 C. Equivalent Cv=1.17 Kv. Kv indicates the volume flow rate in m/h for water at 5oC under a pressure differential of 1 kg/cm.
Gate valve with shutoff spring Design characteristics 1. Stationary hand wheel, non-ascending screw. Possibility of activation by command lever dismounting the hand wheel.. High exterior Epoxy protection against environmental corrosion.. Total passage, self cleaning and minimum charge loss.. Brass screw bolt, rust free. 5. Thread cast GGG 0 hand wheel with EPOXY covering. 6. Totally NBR covered thread cast cone. Totally sealed in both directions. 7. Stainless steel axis, interchangeable NBR packaging rings Construction data and design Constructive design as per Uniform European Regulations EN 1171: (BS 1171: y DIN 5, section ). Construction length as per DIN 0 F (F5 on demand), equivalent EN 55-1, series F1. Flange dimensions and drilling DIN PN. Hand wheel dimensions as per EN. Standards as per EN 19. Nominal pressure rating PN. Temperature rating: o C. Pressure range / Temperature according to EN 109-. Constructive size range 0-00. In compliance with the Direction of Pressure Equipment PED 97//EC with registration number 0575, Category II, Fluids Group 1 y (construction DIN PN 10 on demand - Fig. 5).
Gate valves with shut off spring Maintenance free valves, total passage with minimum obstruction of fluid and charge loss. Clockwise shut off. Absolute sealing in both directions. Provided with rear seats. External anti-corrosion protection. Screw top fastener, brass nut screw, interchangeable axis sealing. Reduced manual torque.ue. Principal Applications Gate valves with shut off springs are primarily used in Residual Water Purification Plants (EDAR), Potable Water Stations (ETAP) and Agricultural Irrigation Systems, swing to their environmental resilience and null maintenance requirements. Materials and parts Nº 1 5 6 7 9 10 PARTS Body Cone Rear seat Screw Bonnet Sealing screw O-ring seal Pressed fitting Sealed fitting Hand wheel MATERIAL GGG 0 GGG 0 / NBR Latón -- Ac. Inox. 10 / 1%Cr GGG 0 NBR NBR Brass -- NBR GGG 0 GGG 0: European Normative EN 156: 1997 - Abbreviated denomination: EN-GJS-00-15. The elastomer is supplied in EPDM on demand. Its use has spread widely over time due to its bidirectional sealing shut off in FIRE fighting systems, industrial applications and acclimatisation techniques. Rating presión / Temperatura T -10 o C 0 o C P (bar) o C Principal dimensions W L H C M D b f w n-d F F5 0 10 1 190 10 0 0 00 5 00 60 5 11 5 55 5 50 6 10 1 15 1 6 0 110 15 0 10 0 55 1 5 0 5 0 05 0 0 6 0 0 00 - - - - - - - 1-1-6 H 00 0 75 7 10 60 0 1-6 n-d 90 5 5 50 0-6 b F 00 10 5 90 55 5 5-0 L Dimensions in millimetres; weight in kilograms. Dimensions as per our standard construction design supply 0 F y F5 (new standard EN 55-1 series 1). 10 9 7 6 5 1 C M D
Straining filters Y pitch Principal dimensions L H Dz Do Dp do n g f h Kg Mesh Ø 15 10 5 5 1 1,05 0 5 105 75 5 1, 5 0 10 115 5 6 1 5,60 10 7 10 5, 0 15 110 10 6,0 0 15 1 10 0 1 9,00 90 17 5 15 1 0 11 1,10 10 1 0 0,00 56 0 15 190,10 00 10 10 6 5, 05 5 0 1 6 5, 0 6 1 0 6 97,00 7 05 55 0 6 1 191,00 00 7 60 10 7 6 1 515,00 *Consult other diameters. Pérdidas de carga y valores Kv Size 0 5 0 00 P (mm/hg) 515 0 5 67 5 1 69 5 0 1 76 Kv (m/h) 5,76 10, 6, 0,9 6,0 10, 1,6 5,5 9,5 57,1 1.0, 1.5.96 Materials and parts Body: Blanking module: Sieve: Seal: Fasteners: Cast iron GG-5 Cast-Iron GG-5 Stainless steel 1.01 Laminated graphite Steel The sieves are fabricated with perforated stainless steel sheets. All the blanking modules have a cover for the regular maintenance of the filter. L ødo x n ødz ødp f h ødo H Applications Water for heating and refrigeration. Vapour. Condensation. Lubrication. g
Ctra. Sta Catalina, 60 001 MURCIA Tel.: 96 6 77 Fax: 96 11 9 e-mail: hidroconta@hidroconta.com www.hidroconta.com ER-06//00 ES-06//00 ASOCIACIÓN DE FABRICANTES DE RIEGO ESPAÑOLES