rushless Motor and river Package Power Supply Input, High Power LV Series Standard Type/Electromagnetic rake Type Introducing the new high power, input LV Series brushless motor and driver with output options of 2 W (1/4 HP) to 4 W (1/2 HP). ommunication control through I/O or RS-485 is available to support a wide variety of applications. Features Power Supply Input, High Power Output Options of 2 W (1/4 HP) to 4 W (1/2 HP), ompact Motor The LV Series are compact, input brushless motors and drivers with output options of 2 W (1/4 HP) to 4 W (1/2 HP). n extensive variety of motors lets you select the model that best suits your specific application. Output Power 2 W (1/4 HP) 4 W (1/2 HP) 14 mm 14 mm Frame Size ( 4.9 in.) ( 4.9 in.) Power Supply Voltage 24 V 48 V Standard Type Motor Type Electromagnetic rake Type Three Types vailable (Shown below are standard type models): 11 mm (4.33 in.) 11 mm (4.33 in.) 142 mm (5.59 in.) ombination Type Parallel Shaft Gearhead 14 mm (4.9 in.) 14 mm (4.9 in.) Round Shaft Type 82 mm (3.23 in.) Features of the Hollow Shaft Flat Gearhead 14 mm ( 4.9 in.), space-saving, hollow shaft flat gearhead has been added to the lineup. ombination Motor Output 2 W (1/4 HP), 4 W (1/2 HP) Gear Ratio 5, 1, 15, 2, 3, 5, 1 Only compatible with the 4 W (1/2 HP) type. Rated Life 5 hrs. Permissible Torque without Saturation The hollow shaft flat gearhead enables permissible torque without saturation so the motor torque can be fully utilized. Permissible Torque [lb-in] 1 8 6 4 2 [N m] 12 1 8 6 4 2 Hollow Shaft Flat Gearhead Parallel Shaft Gearhead 1 2 Gear Ratio 218 mm (8.58 in.) Space-saving The output shaft can be coupled directly to a driven shaft without using a coupling, which allows you to reduce the size and installation space of your equipment. Space-saving 154 mm (6.6 in.) 14 mm (4.9 in.) ombination Type Hollow Shaft Flat Gearhead For gear ratios 5 to 2. [For Three-Phase Motor and Parallel Shaft Gearhead] [For rushless Motor and Hollow Shaft Flat Gearhead]
omes in an Electromagnetic rake Type The electromagnetic brake type is suitable for position holding during standstill or gravitational operation. Note that vertical drive (gravitational operation) requires motors of a specific power supply. Equipped with Functions to Facilitate attery rive apable of driving even if the battery voltage is low warning output notifies when the battery voltage is low Horizontal rive Vertical rive (Gravitational Operation) rive System Standard Type Electromagnetic rake Type Switching Power Supply attery Switching Power Supply attery Power supply limits depend on use. Please contact the nearest Oriental Motor sales office for details. Extended Functions Functions can be extended and settings shown on a digital display by using a separately sold control module (OPX-2). It can also be used in RS-485 communication mode. ontrol Module OPX-2 Item Standard Extended Function Specifi cations Function Speed ontrol Range: 1 4 r/min (speed range 1:4) Speed Regulation: ±.5% Speed setting (internal speed potentiometer, external analog setting) cceleration time, deceleration time Torque limiting Speed ontrol Range: 8 4 r/min (speed range 1:5) Speed Regulation: ±.2% Various isplay Functions: Operating speed (setting of gear ratio and speed increasing ratio), conveyor transportation speed, load factor, alarm code, warning code, I/O monitor Operating data digital settings (speed, torque limiting, acceleration time, deceleration time can be set up to 8 points) I/O signal allocation, test operation ata copy Selectable ual ontrol Method ontrol from a programmable controller can be I/O control or RS-485 communication control. I/O ontrol System Operation can be executed easily with I/O control. ontrol Module control module (OPX-2; accessory sold separately) OPX-2 (Sold separately) is required for parameter settings. Motor river Programmable ontroller ontrol Method for ata Settings and Operation ommands Operating ata and Parameter Settings Operating ata Parameters river potentiometer, control module (OPX-2) ontrol module (OPX-2) Operation ommands (FW, REV, etc.) I/O RS-485 ommunication System RS-485 communication lets you set operating data and parameters and enter operation commands. single programmable controller connects up to 31 drivers and provides multi-axis synchronous starting. The protocol of the RS-485 communication system supports Modbus RTU, allowing it to easily connect with programmable controllers, touch panels and other devices. ontrol Module OPX-2 (Sold separately) Motor river RS-485 ommunication Programmable ontroller ontrol Method for ata Settings and Operation ommands Operation ata and Parameter Setting RS-485 communication, control module (OPX-2) Operation ommands (FW, REV, etc.) RS-485 communication, I/O FW input, REV input and other operation commands can also be controlled from I/O. The test operation function is available with the control module (OPX-2). The internal potentiometers for Speed, cceleration/eceleration and Torque Limiting are still active even when using either the control module (OPX-2) or RS-485 comunication. 2
System onfiguration n example of a single-axis system configuration using I/O control is shown below. 1 Parts sold separately. ccessories (Sold separately) ccessories (Sold separately) Flexible ouplings ( Page 15) Flexible onnection ables ( Page 14) ontrol Module ( Page 15) LV Series ombination Type (Motor/Gearhead) river Programmable ontroller 1 onnection able (ccessory) 2 Power Supply 1 2 1 m (3.3 ft.), 2 m (6.6 ft.) or 3 m (9.8 ft.) connection cable is included. ccessories (Sold separately) External Speed Potentiometer ( Page 15) Motor Speed Indicator This product is not a standard certified product. ( Page 15) IN Rail Mounting Plate ( Page 15) General-Purpose ables ( Page 15) Mounting rackets ( Page 15) Examples of System onfiguration LV Series Sold Separately ombination Type - External Speed IN Rail Mounting Plate Mounting rackets Flexible oupling Parallel Shaft Potentiometer LV62K3S-3 PVR-2KZ PP3 SOL6M8 ML65222 The system configuration shown above is an example of the standard type. Other combinations are available. 3
Product Number ode 1 Series LV : LV Series 2 Motor Frame Size 6: 14 mm (4.9 in.) [Gearhead Frame Size: 11 mm (4.33 in.)] 3 Output Power (W) 2: 2 W (1/4 HP) 4: 4 W (1/2 HP) 4 Power Supply Voltage K: 24 V N: 48 V 5 M: Electromagnetic rake Type lank: Standard Type Gear Ratio/Shaft Type Number: Parallel shaft gearhead type Gear ratio 5 2 6 Hollow shaft fl at gearhead Gear ratio 5 1 : Round Shaft Type 7 Gearhead Type (ombination type only) 8 able Length (Included) S: Parallel Shaft Gearhead F: Hollow Shaft Flat Gearhead 1: 1 m (3.3 ft.) 2: 2 m (6.6 ft.) 3: 3 m (9.8 ft.) Product Line ombination Type The combination type comes with the motor and its dedicated gearhead pre-assembled simplifying installation in equipment. Motors and gearheads are also available separately to facilitate changes or repairs. Standard Type ombination Type Parallel Shaft Gearhead Output Power Power Supply Voltage Gear Ratio 2 W (1/4 HP) 24 V LV62K S- 5, 1, 15, 2, 3, 5, 1, 2 4 W (1/2 HP) 48 V LV64N S- 5, 1, 15, 2, 3, 5, 1, 2 The following items are included in each product. Motor, river, Gearhead, onnection able, Power onnector, Mounting Screws, Parallel Key, Operating Manual cable of 1 m (3.3 ft.), 2 m (6.6 ft.) or 3 m (9.8 ft.) long is included. ombination Type Hollow Shaft Flat Gearhead Output Power Power Supply Voltage Gear Ratio 2 W (1/4 HP) 24 V LV62K F- 1, 15, 2, 3, 5, 1 4 W (1/2 HP) 48 V LV64N F- 5, 1, 15, 2, 3, 5, 1 The following items are included in each product. Motor, river, Gearhead, onnection able, Power onnector, Mounting Screws, Parallel Key, Safety over (with screws), Operating Manual cable of 1 m (3.3 ft.), 2 m (6.6 ft.) or 3 m (9.8 ft.) long is included. Round Shaft Type Output Power Power Supply Voltage 2 W (1/4 HP) 24 V LV62K- 4 W (1/2 HP) 48 V LV64N- The following items are included in each product. Motor, river, onnection able, Power onnector, Operating Manual cable of 1 m (3.3 ft.), 2 m (6.6 ft.) or 3 m (9.8 ft.) long is included. Electromagnetic rake Type ombination Type Parallel Shaft Gearhead Output Power Power Supply Voltage Gear Ratio 2 W (1/4 HP) 24 V LV62KM S- 5, 1, 15, 2, 3, 5, 1, 2 4 W (1/2 HP) 48 V LV64NM S- 5, 1, 15, 2, 3, 5, 1, 2 The following items are included in each product. Motor, river, Gearhead, onnection able, Power onnector, Mounting Screws, Parallel Key, Operating Manual cable of 1 m (3.3 ft.), 2 m (6.6 ft.) or 3 m (9.8 ft.) long is included. ombination Type Hollow Shaft Flat Gearhead Output Power Power Supply Voltage Gear Ratio 2 W (1/4 HP) 24 V LV62KM F- 1, 15, 2, 3, 5, 1 4 W (1/2 HP) 48 V LV64NM F- 5, 1, 15, 2, 3, 5, 1 The following items are included in each product. Motor, river, Gearhead, onnection able, Power onnector, Mounting Screws, Parallel Key, Safety over (with screws), Operating Manual cable of 1 m (3.3 ft.), 2 m (6.6 ft.) or 3 m (9.8 ft.) long is included. Round Shaft Type Output Power Power Supply Voltage 2 W (1/4 HP) 24 V LV62KM- 4 W (1/2 HP) 48 V LV64NM- The following items are included in each product. Motor, river, onnection able, Power onnector, Operating Manual cable of 1 m (3.3 ft.), 2 m (6.6 ft.) or 3 m (9.8 ft.) long is included. Enter the gear ratio in the box ( ) within the model name. 4
Specifications Standard Type 2 W (1/4 HP), 4 W (1/2 HP) ombination Type Parallel Shaft Gearhead LV62K S- LV64N S- ombination Type Hollow Shaft Flat Gearhead LV62K F- LV64N F- Round Shaft Type LV62K- LV64N- Rated Output Power (ontinuous) W (HP) 2 (1/4) 4 (1/2) Rated Voltage V 24 48 Power Source Permissible Voltage Range ±1% Rated Input urrent 13 11 Maximum Input urrent 25 18 Rated Torque N m (oz-in).65 (92) 1.3 (184) Starting Torque 1 N m (oz-in) 1.15 (163) 1.8 (25) Rated Speed r/min 3 Speed ontrol Range r/min 1 4 (nalog setting) 8 4 (igital setting: can be set in 1 r/min increments) 2 Round Shaft Type Permissible Load Inertia J 1-4 kg m 2 (oz-in 2 ) 8.75 (48) 15 (82) Rotor Inertia J 1-4 kg m 2 (oz-in 2 ).61 (3.3).66 (3.6) Load ±.5% (±.2%) 2 max. ( Rated torque, at rated speed, at rated voltage, at normal ambient temperature) Speed Regulation Voltage ±.5% (±.2%) 2 max. (Rated voltage ±1%, at rated speed, with no load, at normal ambient temperature) Temperature ±.5% (±.2%) 2 max. [ +4 (+32 +14 F), at rated speed, with no load, at rated voltage] Electromagnetic rake Type 2 W (1/4 HP), 4 W (1/2 HP) ombination Type Parallel Shaft Gearhead LV62KM S- LV64NM S- ombination Type Hollow Shaft Flat Gearhead LV62KM F- LV64NM F- Round Shaft Type LV62KM- LV64NM- Rated Output Power (ontinuous) W (HP) 2 (1/4) 4 (1/2) Rated Voltage V 24 48 Power Source Permissible Voltage Range ±1% Rated Input urrent 13 11 Maximum Input urrent 25 18 Rated Torque N m (oz-in).65 (92) 1.3 (184) Starting Torque 1 N m (oz-in) 1.15 (163) 1.8 (25) Rated Speed r/min 3 Speed ontrol Range r/min 1 4 (nalog setting) 8 4 (igital setting: can be set in 1 r/min increments) 2 Round Shaft Type Permissible Load Inertia J 1-4 kg m 2 (oz-in 2 ) 8.75 (48) 15 (82) Rotor Inertia J 1-4 kg m 2 (oz-in 2 ).61 (3.3).66 (3.6) Load ±.5% (±.2%) 2 max. ( Rated torque, at rated speed, at rated voltage, at normal ambient temperature) Speed Regulation Voltage ±.5% (±.2%) 2 max. (Rated voltage ±1%, at rated speed, with no load, at normal ambient temperature) Temperature ±.5% (±.2%) 2 max. [ +4 (+32 +14 F), at rated speed, with no load, at rated voltage] Electromagnetic rake 3 rake Type Power off activated type, automatically controlled by the driver Static Friction Torque N m (oz-in).65 (92) 1.3 (184) 1 The time during which the starting torque is effective is no more than five seconds. 2 These specifications apply when a separately sold control module (OPX-2) or communication is used. 3 o not start or stop the motor by turning on/off the power supply, as it will cause the electromagnetic brake to wear abnormally. The values for each specification apply to the motor only. Speed Torque haracteristics ontinuous uty Region : ontinuous operation is possible in this region. Limited uty Region : This region is used primarily when accelerating. When a load that exceeds the rated torque is applied continuously for approximately five seconds, overload protection is activated and the motor coasts to a stop. LV62K S- /LV62K F- /LV62K- LV64N S- /LV64N F- /LV64N- LV62KM S- /LV62KM F- /LV62KM- LV64NM S- /LV64NM F- /LV64NM- Starting Torque Starting Torque Torque [oz-in] 15 1 5 Torque [N m] 1.15.65.45 Limited uty Region ontinuous uty Region Rated Torque Torque [oz-in] 25 2 15 1 5 Torque [N m] 1.8 1.3.95 Limited uty Region ontinuous uty Region Rated Torque 1(8 ) 1 2 3 4 1(8 ) 1 2 3 Speed [r/min] Speed [r/min] Values in parentheses indicate specifications that apply when a separately sold control module ( OPX-2) or communication is used. For the combination types, the values apply to the motor only. 4 Enter the gear ratio in the box ( ) within the model name. 5
ommon Specifications Standard : These specifications apply when the basic motor/driver package is used. Extended Function: These specifications apply when a separately sold control module ( OPX-2) or communication is used. Speed Setting Method Item Standard Extended Function 1 cceleration/ eceleration Time Multi-Speed Setting Method Torque Limiting Function Input Signals Output Signals Setting Method Setting Range Protective Functions Warning Maximum able Extension istance Time Rating Select one of the following methods: Internal speed potentiometer (VR1) External analog setting (External speed potentiometer or external voltage) cceleration and eceleration time potentiometer (VR2):.2 15 seconds (3 r/min with no load) 2 Speeds: 1 speed set by the internal speed potentiometer and 1 speed set by the external analog setting Torque limiting potentiometer (VR3) 2% (ssuming that the rated torque of the motor is 1%) Factory Setting: 2% FW, REV, STOP-MOE, M, LRM-RESET, M-FREE SPEE-OUT, LRM-OUT1 (Y), WNG (Y1) Select one of the following methods: ontrol module (OPX-2) ommunication setting Internal speed potentiometer (VR1) External analog setting (External speed potentiometer or external voltage) Select one of the following methods: ontrol module (with OPX-2) or communication setting:.2 15 seconds (time until setting speed is achieved) cceleration and eceleration time potentiometer (VR2):.2 15 seconds (3 r/min with no load) Select one of the following methods: 8 Speeds: ontrol module (with OPX-2) or communication setting 8 Speeds: 6 speeds set by control module (with OPX-2) and 2 speeds set by analog setting 2 2 1 speed set by the internal speed potentiometer (VR1), and 1 speed set by the external analog setting Select one of the following methods: ontrol module (with OPX-2) ommunication setting Torque limiting potentiometer (VR3) External analog setting (External torque potentiometer or external voltage) 2% (ssuming that the rated torque of the motor is 1%) 3 Factory Setting: 2% 3 ontrol Module (OPX-2) or communication setting can be set in 1% increments. Photocoupler input method Input resistance 3.3 kω Operated by internal power supply: 15 V±1% onnectable external power supply: 24 V 15 +2% urrent 1 m min. Sink logic/source logic: Switchable using a switch (factory setting: sink logic) rbitrary signal allocation to general-purpose input X X5 (6 points) is possible FW [STRT/STOP], REV [RUN/RKE], STOP-MOE [FW/REV], M-FREE, EXT-ERROR, LRM-RESET, HMI, M, M1, M2 Names in [ ] apply in the 3-wire input mode. Open-collector output External use condition Voltage control 2 W (1/4 HP): 3 V max., 4 W (1/2 HP): 53 V max. General-purpose output Y, Y1: 1 m max., SPEE-OUT: 1 m max. SPEE-OUT rbitrary signal allocation to general-purpose output Y, Y1 (2 points) is possible LRM-OUT1, WNG, MOVE, TL, V, LRM-OUT2 Overload, sensor abnormality, initial sensor abnormality, overvoltage, undervoltage, overspeed, overcurrent, EEPROM error, main circuit overheat, external stop, initial operation stop, communication switch setting error, main circuit output abnormality Main circuit overheat, undervoltage, overload, operation stop Motor/river istance: 3.5 m (11.5 ft.) ontinuous 1 The contents able to be set by the driver potentiometers (VR1, VR2, VR3) or external analog settings can be changed using parameters. Note: The torque limiting value may cause an error up to a maximum of approximately ±2% (during rated torque and rated speed) between the setting value and generated torque due to the setting speed, power supply voltage and motor cable extension length. General Specifications Insulation Resistance ielectric Voltage Temperature Rise Operating Environment Item Motor river mbient Temperature mbient Humidity ltitude tmosphere Vibration 1 MΩ or more when 5 V megger is applied between the windings and the case after continuous operation under normal ambient temperature and humidity. Suffi cient to withstand.5 kv at 5 Hz applied between the windings and the case for 1 minute after continuous operation under normal ambient temperature and humidity. 6 (18 F) or less in the windings, and 5 (9 F) or less in the case 1, as measured by the thermocouple method after continuous operation under normal ambient temperature and humidity. 1 MΩ or more when 5 V megger is applied between the power supply terminal and heat sink after continuous operation under normal ambient temperature and humidity. Suffi cient to withstand.5 kv at 5 Hz applied between the power supply terminal and heat sink for 1 minute after continuous operation under normal ambient temperature and humidity. 5 (9 F) or less in the heat sink, as measured by the thermocouple method after continuous operation under normal ambient temperature and humidity. +4 (+32 +14 F) 85% or less (non-condensing) Up to 1 m (33 ft.) above sea level No corrosive gases or dust. annot be used in a radioactive area, magnetic fi eld, vacuum or other special environment Not subject to continuous vibration or excessive impact In compliance with JIS 668-2-6, "Sine-wave vibration test method" Frequency range: 1 55 Hz Pulsating amplitude:.15 mm (.6 in.) Sweep direction: 3 directions (X, Y, Z) Number of sweeps: 2 times Storage ondition 2 mbient Humidity 85% or less (non-condensing) mbient Temperature 25 +7 ( 13 +158 F) (non-freezing) ltitude Up to 3 m (1 ft.) above sea level Thermal lass EN standards: 12 (E) egree of Protection IP4 IP2 1 For round shaft types, please attach a heat radiation plate (material: aluminum) of the appropriate size listed below to maintain a maximum motor case temperature of 9 (194 F): 2 W (1/4 HP): 2 2 mm (7.87 7.87 in.), 5 mm (.2 in.) thick 4 W (1/2 HP): 25 25 mm (9.84 9.84 in.), 6 mm (.24 in.) thick 2 The storage condition applies to a short period such as the period during transportation. Note: o not measure insulation resistance or perform the dielectric strength test while the motor and driver are connected. 6
ommunication Specifications Modbus ommunication Specifications Item ommunication Protocol Electrical haracteristics Transmit/Receive Method aud Rate Physical Layer Number of onnection Units Specifi cations Modbus protocol (Modbus RTU mode) EI-485-compliant For use of twisted-pair wire (TI/EI-568 T5e min. recommended), set the total extension length of the communication cable at max. 5 m (163.9 ft.). Half-duplex communication 96 bps, 192 bps, 384 bps, 576 bps, 1152 bps synchronous method (ata: 8-bit, Stop-it: 1-bit/2-bit, Parity: lank/even No./Odd No.) 31 units max. Gearmotor Torque Table of ombination Type ombination Type Parallel Shaft Gearhead Unit = N m (lb-in) LV62 S- LV64 S- Motor Speed [r/min] Gear Ratio 5 1 15 2 3 5 1 2 1 r/min 2 1 6.7 5 3.3 2 1.5 3 r/min 6 3 2 15 1 6 3 15 4 r/min 8 4 267 2 133 8 4 2 1 3 r/min 4 r/min 1 3 r/min 4 r/min 2.9 (25) 2. (17.7) 5.9 (52) 4.3 (38) 5.9 (52) 4.1 (36) 11.7 (13) 8.6 (76) colored background indicates gear shaft rotation in the same direction as the motor shaft, while the others rotate in the opposite direction. 8.8 (77) 6.1 (53) 17.6 (155) 12.8 (113) 11.7 (13) 8.1 (71) 23.4 (2) 17.1 (151) 16.8 (148) 11.6 (12) 33.5 (29) 24.5 (21) 28. (24) 19.4 (171) 55.9 (49) 4.9 (36) 52.7 (46) 36.5 (32) 7 (61) 63 (55) ombination Type Hollow Shaft Flat Gearhead Unit = N m (lb-in) LV62 F- LV64 F- Motor Speed [r/min] Gear Ratio 5 1 15 2 3 5 1 1 r/min 2 1 6.7 5 3.3 2 1 3 r/min 6 3 2 15 1 6 3 4 r/min 8 4 267 2 133 8 4 1 3 r/min 4 r/min 1 3 r/min 4 r/min 5.5 (48) 4. (35) 5.5 (48) 3.8 (33) 11.1 (98) 8.1 (71) 8.3 (73) 5.7 (5) 16.6 (146) 12.1 (17) The flat gearhead rotates in the opposite direction to the motor when viewed from the front of the gearhead. It rotates in the same direction as the motor when viewed from the rear (motor mounting surface) of the gearhead. 11.1 (98) 7.7 (68) 22.1 (195) 16.2 (143) 16.6 (146) 11.5 (11) 33.2 (29) 24.2 (21) 27.6 (24) 19.1 (169) 55.3 (48) 4.4 (35) 55.3 (48) 38.3 (33) 11 (97) 8.8 (71) 7 (61) 63 (55) 7 (61) 63 (55) Rotation irection of the Hollow Shaft Flat Gearhead The hollow shaft flat gearhead of the combination type rotates in the direction as shown below, with respect to the direction input from the driver. Front View Rear View Flat Gearhead Flat Gearhead When the W input is ON. When the W input is ON. When the W input is ON. When the W input is ON. Enter the power supply voltage K or N (KM and NM for electromagnetic brake type) in the box ( ) within the model name. Enter the gear ratio in the box ( ) within the model name. 7
Permissible Overhung Load and Permissible Thrust Load ombination Type Parallel Shaft Gearhead LV62 S- LV64 S- 5, 1, 15, 2 3, 5 1, 2 Gear Ratio 1 mm (.39 in.) from shaft end Permissible Overhung Load 2 mm (.79 in.) from shaft end Permissible Thrust Load N lb. N lb. N lb. 1 3 r/min 55 123 8 18 4 r/min 5 112 7 157 2 45 1 3 r/min 1 22 125 28 4 r/min 9 2 11 24 3 67 1 3 r/min 14 31 17 38 4 r/min 12 27 14 31 4 9 ombination Type Hollow Shaft Flat Gearhead LV62 F- LV64 F- LV64 F- only. 5, 1 15, 2 3, 5, 1 Gear Ratio 1 mm (.39 in.) from mounting surface of gearhead Permissible Overhung Load 2 mm (.79 in.) from mounting surface of gearhead Permissible Thrust Load N lb. N lb. N lb. 1 3 r/min 123 27 17 24 4 r/min 113 25 99 22 1 3 r/min 168 37 147 33 4 r/min 155 34 136 3 8 18 1 3 r/min 24 45 178 4 4 r/min 19 42 166 37 Round Shaft Type LV62 - LV64-1 mm (.39 in.) from shaft end Permissible Overhung Load 2 mm (.79 in.) from shaft end N lb. N lb. 197 44 221 49 Permissible Thrust Load The permissible thrust load should not be greater than half the motor mass. Permissible Load Inertia J of ombination Type ombination Type Parallel Shaft Gearhead Unit = 1-4 kg m 2 (oz-in 2 ) LV62 S- LV64 S- Gear Ratio When instantaneous stop or instantaneous bi-directional operation is performed 5 1 15 2 3 5 1 2 1 (55) 37.5 (21) 46 (25) 15 (82) 1 (55) 338 (185) 17 (93) 6 (33) 39 (21) 135 (74) 93 (51) 375 (21) 18 (98) 375 (21) 37 (2) 375 (21) ombination Type Hollow Shaft Flat Gearhead Unit = 1-4 kg m 2 (oz-in 2 ) LV62 F- LV64 F- Gear Ratio When instantaneous stop or instantaneous bi-directional operation is performed 5 1 15 2 3 5 1 1 (55) 37.5 (21) 46 (25) 15 (82) 1 (55) 338 (185) 17 (93) 6 (33) 39 (21) 135 (74) 93 (51) 375 (21) 18 (98) 375 (21) LV64 F- only. Enter the power supply voltage K or N (KM and NM for electromagnetic brake type) in the box ( ) within the model name. Enter the gear ratio in the box ( ) within the model name. 8
imensions Unit = mm (in.) Mounting screws are included with the combination type. Standard Type 2 W (1/4 HP), 4 W (1/2 HP) Motor/Parallel Shaft Gearhead Motor Gearhead Gear Ratio L Mass kg (lb.) XF 5 2 6 (2.36) 1139 LV62K S- LVM62K-GFS GFS6G 3, 5 72 (2.83) 5.4 (11.9) 1139 LV64N S- LVM64N-GFS 1, 2 86 (3.39) 1139 14 (4.9) 18.5 (.73) 82 (3.23) 1 (.39) L 5±1 (1.97±.4) 5 (.2) ϕ25 (ϕ.98) 35±.5 (1.38±.2) 32 (1.26) ϕ22.21 (ϕ.8661.8) 24.5 (.96) 2±.5 (.79±.2) ϕ42 (ϕ1.65) 14 ( 4.9) 11 ( 4.33) 4 ϕ8.5 (ϕ.335) Thru M6 12 (.47) eep ϕ12±.5 (ϕ4.72±.2) 33 (1.3) Housing: F22R-3S-7.92 (HIROSE) Key and Key Slot (Included) 32±.2 (1.26±.8) 6.3 (.2362.12) 18.5.1 (.728.4) 6.3 (.2362.12) 42 (1.65) Motor able ϕ11 (ϕ.43) 5 (2) Housing: 5113-5 (MOLEX) t the time of shipment, a key is inserted on the gearhead's shaft. Motor/Hollow Shaft Flat Gearhead LV62K F-, LV64N F- Motor: LVM62K-GFS, LVM64N-GFS Gearhead: GFS6G FR Mass: 7.2 kg (15.8 lb.) (Including gearhead) 114 1 (.4) 83.5 (3.29) 7 (.276) 5 (.2) ϕ58.46 (ϕ2.2835.18) +.4 8 +.16 (.315 ) 14 (4.9) 14 (4.9) 114 (4.49) ϕ4 (ϕ1.57) ϕ12±.5 (ϕ4.72±.2) 4 ϕ8.5 (ϕ.335) Thru 28.3 (1.11) 14 (4.9) 33 (1.3) 14 (4.9) 218 (8.58) 3 (1.18) 15 (.59) 1.35 (.5) 18.5 (.73) 89.5 (3.52) 3 (1.18) 15 (.59) 1.35 (.5) 1 (.39) 82 (3.23) 67 (2.64) 5 (.2) 3±.2 (1.181±.8) Key (Included) 8.36 (.315.14) 7.9 (.2756.35) Housing: F22R-3S-7.92 (HIROSE) ϕ26.2.21 (ϕ1.315.83 ) ϕ25.33 (ϕ.9843.13 ) ϕ25.33 (ϕ.9843.13 ) ϕ26.2.21 (ϕ1.315.83 ) 42 (1.65) Motor able ϕ11 (ϕ.43) 5 (2) Housing: 5113-5 (MOLEX) Enter the gear ratio in the box ( ) within the model name. 9
Round Shaft Type LV62K-, LV64N- Motor: LVM62K-, LVM64N- Mass: 2.4 kg (5.3 lb.) 1141 14 (4.9) 82 (3.23) 1 (.39) 37±1 (1.46±.4) 2 (.8) 3 (1.18) 13 (.51) ϕ14.18 (ϕ.5512.7) ϕ94.35 (ϕ3.78.14) 14 ( 4.9) 4 ϕ8.5 (ϕ.335) Thru ϕ12±.5 (ϕ4.72±.2) 18.5 (.73) Motor able ϕ11 (ϕ.43) 42 (1.65) 5 (2) 33 (1.3) Housing: F22R-3S-7.92 (HIROSE) Housing: 5113-5 (MOLEX) Electromagnetic rake Type 2 W (1/4 HP), 4 W (1/2 HP) Motor/Parallel Shaft Gearhead Motor Gearhead Gear Ratio L Mass kg (lb.) XF 5 2 6 (2.36) 1142 LV62KM S- LVM62KM-GFS GFS6G 3, 5 72 (2.83) 6.4 (14.1) 1142 LV64NM S- LVM64NM-GFS 1, 2 86 (3.39) 1142 124 (4.88) 1 (.39) L 5±1 (1.97±.4) 5 (.2) 35±.5 (1.38±.2) 32 (1.26) ϕ22.21 (ϕ.8661.8) 24.5 (.96) 2±.5 (.79±.2) M6 12 (.47) eep 4 ϕ8.5 (ϕ.335) Thru 18.5 (.73) 14 (4.9) ϕ25 (ϕ.98) ϕ42 (ϕ1.65) 14 ( 4.9) 11 ( 4.33) Housing: F22R-3S-7.92 (HIROSE) ϕ12±.5 (ϕ4.72±.2) 33 (1.3) Housing: 5113-5 (MOLEX) Motor able ϕ11 (ϕ.43) 42 (1.65) 5 (2) Housing: 5113-2 (MOLEX) Key and Key Slot (Included) 32±.2 (1.26±.8) 6.3 (.2362.12) 6.3 (.2362.12) 18.5.1 (.728.4) t the time of shipment, the key is inserted on the gearhead's shaft. Enter the gear ratio in the box ( ) within the model name. 1
Motor/Hollow Shaft Flat Gearhead LV62KM F-, LV64NM F- Motor: LVM62KM-GFS, LVM64NM-GFS Gearhead: GFS6G FR Mass: 8.2 kg (18. lb.) (Including gearhead) 1143 1 (.4) 83.5 (3.29) 7 (.276) 5 (.2) ϕ58.46 (ϕ2.2835.18) +.4 8 +.16 (.315 ) 14 (4.9) 14 (4.9) 114 (4.49) ϕ4 (ϕ1.57) ϕ12±.5 (ϕ4.72±.2) 4 ϕ8.5 (ϕ.335) Thru 28.3 (1.11) 33 (1.3) 14 (4.9) 218 (8.58) 14 (4.9) 18.5 (.73) 1 (.39) 124 (4.88) 67 (2.64) 5 (.2) Key (Included) 3 (1.18) 15 (.59) 1.35 (.5) 89.5 (3.52) 3 (1.18) 15 (.59) 1.35 (.5) 3±.2 (1.181±.8) 8.36 (.315.14) 7.9 (.2756.35) Housing: F22R-3S-7.92 (HIROSE) Housing: 5113-5 (MOLEX) Housing: 5113-2 (MOLEX) ϕ26.2.21 (ϕ1.315.83 ) ϕ25.33 (ϕ.9843.13 ) ϕ25.33 (ϕ.9843.13 ) ϕ26.2.21 (ϕ1.315.83 ) Motor able ϕ11 (ϕ.43) 42 (1.65) 5 (2) Round Shaft Type LV62KM-, LV64NM- Motor: LVM62KM-, LVM64NM- Mass: 3.4 kg (7.5 lb.) 1144 18.5 (.73) 14 (4.9) 124 (4.88) 1 (.39) 37±1 (1.46±.4) 2 (.8) 3 (1.18) 13 (.51) ϕ14.18 (ϕ.5512.7) ϕ94.35 (ϕ3.78.14) Motor able ϕ11 (ϕ.43) 42 (1.65) 5 (2) 14 ( 4.9) 4 ϕ8.5 (ϕ.335) Thru ϕ12±.5 (ϕ4.72±.2) 33 (1.3) Housing: F22R-3S-7.92 (HIROSE) Housing: 5113-5 (MOLEX) Housing: 5113-2 (MOLEX) Enter the gear ratio in the box ( ) within the model name. 11
river LV2KM, LV4NM Mass:.6 kg (1.32 lb.) 1138 5 (.2) 6.5 (.26) 22.5 (.89) 1 (3.94) 25 (.98) Max. 5 (1.97) 45 (1.77) 147 (5.79) 134 (5.28) 16 (6.3) 147 (5.79) 5 (.2) 14 (.55) ϕ4.5 (ϕ.177) Thru Slits Slits 5 (.2) Pitch 7.62 (.3) Pitch 4 M3 8 (.39) 25 (.98) 2 ϕ4.5 (ϕ.177) Thru onnection able (Included) able Type Length L [m (ft.)] onnection able 1 m (3.3 ft.) 1 (3.3) onnection able 2 m (6.6 ft.) 2 (6.6) onnection able 3 m (9.8 ft.) 3 (9.8) Standard Type 12.72 (.5) 32.14 (1.27) 21.7 (.85) 7.8 (.31) Motor Side L ϕ11 (ϕ.43) river Side 1.4 (.41) 23.42 (.92) 14.7 (.58) 5.8 (.23) ode Housing Product Name Manufacturer F22R-3EP-7.92 HIROSE 51198-5 MOLEX F22R-3S-7.92 HIROSE 5113-5 MOLEX Electromagnetic rake Type 12.72 (.5) 32.14 (1.27) 21.7 (.85) 7.8 (.31) 14.2 (.56) 7.8 (.31) Motor Side L ϕ11 (ϕ.43) river Side E F E F 1.4 (.41) 23.42 (.92) 14.7 (.58) 5.8 (.23) 7.2 (.28) 5.8 (.23) ode Housing Product Name Manufacturer F22R-3EP-7.92 HIROSE 51198-5 MOLEX 51198-2 MOLEX F22R-3S-7.92 HIROSE E 5113-5 MOLEX F 5113-2 MOLEX 12
onnection and Operation Names and Functions of river Parts ommunication Setting Switch (SW2) Unit Number Setting Switch (SW3) -T LE (Green) -ERR LE (Red) RS-485 ommunication onnector [N5, N6] 2 ommunication onnector [N7] Electromagnetic rake onnector [N8] ontrol Power-Supply Input Terminal (T1) Torque Limiting Potentiometer (VR3) Standard Setting Switch (SW1) I/O Signal onnector [N4] 1 POWER LE (Green) LRM LE (Red) Internal Speed Potentiometer (VR1) cceleration and eceleration Time Potentiometer (VR2) Motor Signal onnector [N3] Motor Power onnector [N2] Main Power Supply Input Terminal [N1] 1 The following items are needed for the connector that connects the I/O signals: - -sub connector (15-pin), hood (screw: No. 4-4UN) - General-purpose cable is available as an accessory. Page 15 Name POWER LE (Green) LRM LE (Red) Internal Speed Potentiometer (VR1) cceleration and eceleration Time Potentiometer (VR2) Torque Limiting Potentiometer (VR3) Main Power Supply Input Terminal [N1] Motor Power onnector [N2] Motor Signal onnector [N3] Electromagnetic rake onnector [N8] I/O Signal onnector [N4] Standard Setting Switch (SW1) ommunication onnector [N7] ontrol Power-Supply Input Terminal (T1) 2 RS-485 ommunication onnector [N5, N6] 2 -T LE (Green) 2 -ERR LE (Red) 2 ommunication Setting Switch (SW2) 2 Unit Number Setting Switch (SW3) 2 escription Lights when main or logic power supply is on. links while an alarm (protective function) occurs. The type of alarm can be confi rmed by the blink count. Sets the motor's speed. Sets the motor's starting and stopping times. Sets the motor's torque limiting value. onnects the main power supply. LV62: +24V, LV64: +48V onnects the motor power connector. onnects the motor signal connector. onnects the motor electromagnetic brake connector. Used when an external control device is used or an operation command is entered. Switches the speed response, sink logic/ source logic, and the external voltage. onnects to control module OPX-2. onnects the driver's power supply for signal control. onnects the RS-485 communication cable. Lights when communications are normal with the master station via RS-485 communication. Lights when a communication abnormality occurs with the master station via RS-485 communication. Sets the baud rate, communication protocol and terminating resistor of the RS-485 communication. Sets the unit number of the RS-485 communication. 2 Used with RS-485 communications. n RS-485 communication cable is available as an accessory. Page 15 onnection iagrams connection example for sink logic. External Voltage (Within voltage selected with SW1 No. 2) Power Supply LV62: 24 V±1% LV64: 48 V±1% 2 1 + - FW REV STOP-MOE M LRM-RESET M-FREE IN-OM External Speed Potentiometer PVR-2KZ (ccessory) 3 VH VM VL VM VL N1 + - N4 1 2 3 4 9 1 5 13 12 11 3.3 kω +15 V V V V river N2 N3 N8 N4 6 5 14 7 15 8 SPEE-OUT IN-OM WNG (+) WNG (-) Motor Power onnector Motor Signal onnector Electromagnetic rake onnector LRM-OUT (+) LRM-OUT (-) 1 2 2 Recommended Power Supply apacity Package Name Input Power Supply Voltage Power Supply apacity LV62 24 V±1% 8 W min. LV64 48 V±1% 1 kw min. LV62: 3 V max. 1 m max. LV64: 53 V max. 1 m max. LV62: 3 V max. 1 m max. LV64: 53 V max. 1 m max. 1 To prevent the current value from exceeding 1 m, connect a limiting resistor appropriate for the power supply voltage that will be used. 2 To prevent the current value from exceeding 1 m, connect a limiting resistor appropriate for the power supply voltage that will be used. Refer to the operating manual for detailed information and notes about this product. Please download the operating manual from our website or contact your nearest Oriental Motor sales office. http://www.orientalmotor.com/ 13
List of Motor and river ombinations Standard Type ombination Type Parallel Shaft Gearhead Output Power Motor Gearhead river 2 W (1/4 HP) LV62K S- LVM62K-GFS LV2KM GFS6G 4 W (1/2 HP) LV64N S- LVM64N-GFS LV4NM ombination Type Hollow Shaft Flat Gearhead Output Power Motor Gearhead river 2 W (1/4 HP) LV62K F- LVM62K-GFS LV2KM GFS6G FR 4 W (1/2 HP) LV64N F- LVM64N-GFS LV4NM Round Shaft Type Output Power Motor river 2 W (1/4 HP) LV62K- LVM62K- LV2KM 4 W (1/2 HP) LV64N- LVM64N- LV4NM Electromagnetic rake Type ombination Type Parallel Shaft Gearhead Output Power Motor Gearhead river 2 W (1/4 HP) LV62KM S- LVM62KM-GFS LV2KM GFS6G 4 W (1/2 HP) LV64NM S- LVM64NM-GFS LV4NM ombination Type Hollow Shaft Flat Gearhead Output Power Motor Gearhead river 2 W (1/4 HP) LV62KM F- LVM62KM-GFS LV2KM GFS6G FR 4 W (1/2 HP) LV64NM F- LVM64NM-GFS LV4NM Round Shaft Type Output Power Motor river 2 W (1/4 HP) LV62KM- LVM62KM- LV2KM 4 W (1/2 HP) LV64NM- LVM64NM- LV4NM Enter the gear ratio in the box ( ) within the model name. ccessories (Sold separately) Flexible onnection ables Use of flexible connection cables is recommended in applications where the cable will be bent and stretched repeatedly. The maximum extension length is 3.5 m (11.5 ft.). Standard Type Electromagnetic rake Type Length L [m (ft.)] 1LV2R 1 (3.3) 2LV2R 2 (6.6) 3LV2R 3 (9.8) Length L [m (ft.)] 1LV2MR 1 (3.3) 2LV2MR 2 (6.6) 3LV2MR 3 (9.8) imensions Unit = mm (in.) imensions Unit = mm (in.) 12.72 (.5) 32.14 (1.27) 21.7 (.85) 7.8 (.31) Motor Side L ϕ1 (ϕ.39) ode Housing Product Name Manufacturer F22R-3EP-7.92 HIROSE 51198-5 MOLEX F22R-3S-7.92 HIROSE 5113-5 MOLEX river Side 1.4 (.41) 23.42 (.92) 14.7 (.58) 5.8 (.23) 12.72 (.5) 32.14 (1.27) 21.7 (.85) 7.8 (.31) 14.2 (.56) 7.8 (.31) Motor Side ϕ1 (ϕ.39) ode Housing Product Name Manufacturer F22R-3EP-7.92 HIROSE 51198-5 MOLEX 51198-2 MOLEX F22R-3S-7.92 HIROSE E 5113-5 MOLEX F 5113-2 MOLEX L river Side E F E F 1.4 (.41) 23.42 (.92) 14.7 (.58) 5.8 (.23) 7.2 (.28) 5.8 (.23) 14
ontrol Module llows for setting of various parameters and confirmation of the setting data. It is used by connecting to the driver communication connector (N7). OPX-2 External Speed Potentiometer Used to set and adjust the speed of motor. PVR-2KZ Motor Speed Indicator Indicates speed of the motor. SM496 Motor and Gearhead Mounting rackets edicated mounting brackets for mounting a motor and gearhead. pplicable Product LV62 S- LV64 S- LV62 - LV64 - SOL6M8 Note: This mounting bracket cannot be used with the hollow shaft flat gearhead. Flexible ouplings clamp type coupling for connecting the motor/gearhead shaft with the driven shaft. Once the motor or gearhead are chosen, the coupling can be selected. pplicable Product Shaft iameter [mm (in.)] oupling Type LV62 S- LV64 S- ϕ22 (ϕ.8661) ML65 Type LV62 - LV64 - ϕ14 (ϕ.5512) ML4 Type river able General-Purpose ables edicated 15-conductor cables for connecting the I/O signal connector and programmable controller. They are highquality, noise-blocking, double-shielded cables. Length L [m (ft.)] 151 1 (3.3) 152 2 (6.6) imensions Unit = mm (in.) 43 (1.69) 16 (.63) ϕ9.8 (ϕ.39) 46 (1.81) L 9 (3.54) Noise-locking Property The figure below shows the noise effects on a signal line. s you can see, the noise-blocking effect is high with signal lines that have a low level value. Oriental Motor driver cables come with double-shielding that includes aluminum foil-shielding and braidedshielding, which provides excellent noise-blocking characteristics. Level [dpw] 1 9 8 7 6 5 4 3 2 Non-shielded able Shielded able (raided-shielded only) 151, 152 (ouble-shielded) 1 1 1 Frequency [MHz] RS-485 ommunication able This cable with connector assemblies are available to connected drivers for multi axis operation. 1-RS4 imensions Unit = mm (in.) IN Rail Mounting Plate Use this plate when installing the driver to a IN rail. 11 (4.33) 21.7 (.86) 11.7 (.46) PP3 ϕ5.5 (ϕ.22) RS-485 ommunication onnector (N5/N6) RS-485 ommunication able Enter the power supply voltage K or N (KM and NM for electromagnetic brake type) in the box ( ) within the model name. Enter the gear ratio in the box ( ) within the model name. 15