OPERATOR S & PARTS MANUAL MODEL PS5 & PS POWER SEEDER SERIAL NUMBER: PURCHASE DATE: PS5AD002 AND UP PSAD005 AND UP MANUAL P/N: P970750 RELEASE DATE: APRIL 30, 200 00-437-9779 www.paladinbrands.com PO Box 230, Jamestown, ND 5402-0230, United States of America
notes
PREFACE This manual describes the installation, operation and maintenance of the Harley Power Seeder. Read and understand the manual in its entirety before performing installation, or maintenance in order to ensure the equipment s optimum level of performance. Read and follow all safety and precautionary notes included in this text. Throughout this manual, references are made to front, back, right and left directions. These are determined by sitting in the operator s seat of the tractor. REMINDER: Fill in the warranty card and mail within 10 days of your purchase date. While filling in the card with the correct information, put the date purchased and the serial number on the front cover of this manual. Should you need to call your dealer or Harley Attachments, this information will help them to more quickly provide accurate service for you. Any questions related to this should be directed to Harley Attachments customer service at 00-437-9779. TABLE OF CONTENTS OWNER ASSISTANCE...2 SPECIFICATIONS...3 BOLT TORQUE CHART...4 SAFETY STATEMENTS...5 GENERAL SAFETY PRECAUTIONS... 5-7 EQUIPMENT SAFETY PRECAUTIONS... 7-9 SAFETY DECAL AND SERIAL TAG PLACEMENT...10-11 OPERATIONAL PROCEDURE... 12-1 MAINTENANCE... 1-17 ASSEMBLY, PARTS IDENTIFICATION... 1-3 WARRANTY POLICY...37 MODEL PS5 & PS HARLEY POWER SEEDER
OWNER ASSISTANCE Harley Attachments, LLC and your authorized Harley dealer want you to be completely satisfied with your investment. To resolve any problems that may occur, please contact the Service Manager of your local Harley dealer. If your problem has not been handled to your satisfaction, contact: Customer Service (:00am 5:00pm CT) Harley Attachments, LLC PO Box 230 Jamestown, ND 5402-0230 701-252-9300 00-437-9779 Parts Fax: 701-952-9307 E-mail: harleycs@harleyattachments.com Please be prepared to provide the following information: Your name, address and telephone number Machine model and SERIAL NUMBER Dealership name and address Machine purchase date Nature of problem Local Dealer Information: Contact: Address: Phone #1: Phone #2: E-mail: 2 MODEL PS5 & PS HARLEY POWER SEEDER
SPECIFICATIONS PS5 PS Overall Width (A) 70.5 Inches 2.75 Inches Overall Length (B) 23.75 Inches 23.75 Inches Overall Height (C) 34.75 Inches 34.75 Inches Seeding Width (D) 2.75 Inches 75.00 Inches Weight (Empty) 357 lbs 391 lbs with 3 Point 42 lbs 49 lbs with Rake 2 lbs 1147 lbs HP Range (with Rake) 1-35 30-40 Category 1 1 3-Point Lift Capacity Required 10 lbs 1200 lbs at 24 Inches with Scarifier * 3-Point Lift Capacity Required 100 lbs 2200 lbs at 24 Inches with Rake * Drum Diameter 1.0 Inches 1.0 Inches * Use tractor front counter weight as needed. D C A B MODEL PS5 & PS HARLEY POWER SEEDER 3
BOLT TORQUE CHART After every ten (10) hours of operation, check all hardware and tighten where required. SAE Series Torque Chart DO NOT use these values if a different torque value or tightening procedure is listed for a specific application. Torque values listed are for general use only. Fasteners should be replaced with the same grade. Make sure fastener threads are clean and you properly start thread engagement. This will prevent them from failing when tightening. Metric Series Torque Chart Use only metric tools on metric hardware. Other tools may not fit properly. They may slip and cause injury. 4 MODEL PS5 & PS HARLEY POWER SEEDER
SAFETY STATEMENTS DANGER WARNING CAUTION NOTICE This statement is used where serious injury or death will result if the instructions are not followed properly. This statement is used where serious injury or death could result if the instructions are not followed properly. This statement is used where minor injury could result if the instructions are not followed properly. This statement is used where equipment or property damage could result if the instructions are not followed properly. This symbol by itself or used with a safety signal word throughout this manual is used to call your attention to instructions involving your personal safety or the safety of others. Failure to follow these instructions can result in injury or death. GENERAL SAFETY PRECAUTIONS WARNING WARNING READ MANUAL PRIOR TO INSTALL Improper installation, operation, or maintenance of this equipment could result in serious injury or death. Operators and maintenance personnel should read this manual as well as all manuals related to this equipment and the prime mover thoroughly before beginning installation, operation, or maintenance. FOLLOW ALL SAFETY INSTRUCTIONS IN THIS MANUAL AND THE PRIME MOVERS MANUAL. READ AND UNDERSTAND ALL SAFETY STATEMENTS Read all safety decals and safety statements in all manuals prior to operating or working on this equipment. Know and obey all OSHA regulations, local laws and other professional guidelines for your operation. Know and follow good work practices when assembling, maintaining, repairing, mounting, removing, or operating this equipment. KNOW YOUR EQUIPMENT Know your equipment s capabilities, dimensions, and operations before operating. Visually inspect your equipment before you start and never operate equipment that is not in proper working order with all safety devices intact. Check all hardware to assure it is tight. Make certain that all locking pins, latches, and connection devices are properly installed and secured. Remove and replace any damaged, fatigued, or excessively worn parts. Make certain all safety decals are in place and are legible. Keep decals clean and replace them if they become worn and hard to read. MODEL PS5 & PS HARLEY POWER SEEDER 5
WARNING WARNING WARNING PROTECT AGAINST FLYING DEBRIS Always wear proper safety glasses, goggles, or a face shield when driving pins in or out or when any operation causes dust, flying debris, or any other hazardous material. LOWER OR SUPPORT RAISED EQUIPMENT Do not work under raised 3 point lift arms without supporting them. Do not use support material made of concrete blocks, logs, buckets, barrels, or any other material that could suddenly collapse or shift positions. Make sure support material is solid, not decayed, warped, twisted, or tapered. Lower lift arms to ground level or onto blocks. Lower lift arms and attachments to the ground before leaving the cab or operator s station. USE CARE WITH HYDRAULIC FLUID PRESSURE Hydraulic fluid pressure can penetrate the skin and cause serious injury or death. Hydraulic leaks under pressure may not be visible. Before connecting or disconnecting hydraulic hoses, read your prime movers operator s manual for detailed instructions on connecting and disconnecting hydraulic hoses or fittings. Keep unprotected body parts, such as face, eyes, and arms as far away as possible from a suspected leak. Flesh injected with hydraulic fluid may develop gangrene or other permanent disabilities. If injured by injected fluid, see a doctor at once. If your doctor is not familiar with this type of injury, ask him to research immediately to determine proper treatment. Wear safety glasses, protective clothing, and use a sound piece of card board or wood when searching for hydraulic leaks. DO NOT USE YOUR HANDS! SEE ILLUSTRATION BELOW. WARNING DO NOT MODIFY MACHINE OR ATTACHMENTS Modifications may weaken the integrity of the attachment and may impair the function, safety, life, and performance of the attachment. When making repairs, use only the manufacturer s genuine parts, following authorized instructions. Other parts may be substandard in fit and quality. Never modify any ROPS (Roll Over Protection System) equipment or device. Any modifications must be authorized in writing by the manufacturer. MODEL PS5 & PS HARLEY POWER SEEDER
WARNING WARNING SAFELY OPERATE EQUIPMENT Do not operate equipment until you are completely trained by a qualified operator in how to use the controls, know its capabilities, dimensions, and all safety requirements. See your prime movers manual for these instructions. Keep all step plates, grab bars, pedals, and controls free of dirt, grease, debris, and oil. Never allow anyone to be around the equipment when it is operating or being serviced. Do not allow riders on the attachment or the prime mover. Do not operate the equipment from anywhere other than the correct operators position. Never leave equipment unattended with the engine running or with this attachment in a raised position. Do not alter or remove any safety feature from the prime mover or this attachment. Know your work site safety rules as well as traffic rules and flow. When in doubt on any safety issue, contact your supervisor or safety coordinator for an explanation. SAFELY MAINTAIN AND REPAIR EQUIPMENT Do not wear loose clothing or any accessories that can catch in moving parts. If you have long hair, cover or secure it so that it does not be come entangled in the equipment. Work on a level surface in a well lit area. Use properly grounded electrical outlets and tools. Use the correct tool for the job at hand. Make sure they are in good condition for the task required. Wear the protective equipment specified by the tool manufacturer. EQUIPMENT SAFETY PRECAUTIONS NOTICE Safety is a primary concern in the design and manufacture of our products. Unfortunately, our efforts to provide safe equipment can be wiped out by a single careless act of an operator. In addition, to the design and configuration of equipment, hazard control and accident prevention are dependent upon the awareness, concern, prudence, and proper training of personnel involved in the operation, transport, maintenance, and storage of equipment. The designed and tested safety of this equipment depends on it being operated within the limitations as explained in this manual. WARNING INITIAL SET-UP AND SYSTEMS CHECK Always check with your prime mover manual or dealer for counter weight ballast that may be required for machine stability. Air in hydraulic systems can cause erratic operation and allows loads or equipment components to drop unexpectedly. Before operating equipment purge any air in the system by engaging all hydraulic functions. Check that all control lever positions function as instructed in the Operator s Manual. Do not operate until control lever and equipment MODEL PS5 & PS HARLEY POWER SEEDER 7
movements are correct. Make sure all hydraulic hoses, fittings and valves are in good condition and not leaking before starting power unit. Check and route hoses carefully to prevent damage. Hoses must not be twisted, bent sharply, kinked, frayed, pinched, or come into contact with any moving parts. Operate moveable components through full operational range to check clearances. Replace damaged hoses immediately. Ensure implement is properly attached, adjusted and in good condition. Tractor must be equipped with ROPS and seat belt/operator restraint. Keep seat belt/operator restraint securely fastened/engaged. Falling off tractor can result in death from being run over or crushed. Keep ROPS systems in place at all times. SAFELY OPERATE EQUIPMENT WARNING Improper operation can cause the machine to tip or roll over and cause injury or death. Keep tractor lift arms and attachment as low as possible. Turn on level ground. Go up and down slopes, not across them. Keep the heavy end of the machine uphill. Only engage power when equipment is at ground level. Always disengage power when equipment is raised off the ground. Do not disconnect hydraulic lines until all system pressure is relieved. Never go underneath equipment lowered to the ground or raised. Hydraulic system leak down, hydraulic system failures, mechanical failures or movement of control levers can cause equipment to drop or rotate unexpectedly and cause severe injury or death. Never direct discharge toward people, animals or property. Do not operate equipment while under the influence of alcohol or drugs. Operate only in the daylight or good artificial lighting. Always comply with all state and local lighting and marking requirements. Ensure equipment is properly attached, adjusted and in good operating condition. Before starting tractor, check all equipment driveline guards for damage and make sure they rotate freely on all drivelines. Replace any damaged guards. If guards do not rotate freely on drivelines, repair and replace bearings before operating. Make sure driveline is correct length to prevent bottoming out or pulling apart during the full lift range of the hitch. Make sure spring-activated locking pin or collar slides freely and is seated firmly in tractor PTO splined groove. A minimum 20% of tractor and equipment weight must be on tractor front wheels with attachments in transport position. Without this weight, tractor could tip over causing personal injury or death. The weight may be attained with a loader, front wheel weights, ballast in tires, or front tractor weights. When attaining wheels, you must not exceed the Roll Over Protection Structure (ROPS) weight certification. Weigh the tractor and equipment. Do not estimate. MODEL PS5 & PS HARLEY POWER SEEDER
Ensure shields and guards are properly installed and in good condition. Replace if damaged. WARNING WARNING WATCH FOR OPERATING HAZARDS Look down and to the rear and make sure area is clear before operating in reverse. Watch for hidden hazards on the terrain during operation. Use extreme care when working close to fences, ditches, other obstructions, or on hillsides. Reduce ground speed on slopes and rough terrain. Do not operate on steep slopes. Do not stop, start, or change directions suddenly on slopes. Stop tractor and implement immediately upon striking an obstruction. Dismount tractor using proper procedure. Inspect and repair any damage before resuming operation. MAINTENANCE SAFETY Your dealer can supply original equipment hydraulic accessories and repair parts. Substitute parts may not meet original equipment specifications and may be dangerous. Avoid electrical system hazards. Never work on the electrical system unless you are qualified and thoroughly familiar with system details and the special handling requirements. Disconnect battery before working on electrical system. Remove ground cable first. When reconnecting battery, connect ground cable last. Never perform service or maintenance with engine running. Tighten all bolts, nuts and screws, and check that all cotter pins are installed securely to ensure equipment is in a safe condition before operating. MODEL PS5 & PS HARLEY POWER SEEDER 9
SAFETY DECAL AND SERIAL TAG PLACEMENT 1 4 4 2 7 5 3 Figure 1. Safety Decals 10 MODEL PS5 & PS HARLEY POWER SEEDER
SAFETY DECALS #1 - PN: P97250 #3 - SERIAL TAG #2 - PN: P970100 # - PN: P970300 #5 - PN: P97510 #7 - PN: 50-079 #4 - PN: P97400 (Red) MODEL PS5 & PS HARLEY POWER SEEDER 11
NOTICE OPERATIONAL PROCEDURE The Harley Power Seeder is designed for applying seed directly onto conditioned soil, in conjunction with the Harley Power Rake. This manual contains information for the PS5 & PS model. Refer to the information in this manual for specifications, parts, assemblies and adjustments. The Harley Power Seeder used with the Harley Power Rake, allows the operator to pulverize and condition the seedbed, while at the same time, drop a metered amount of seed onto a prepared bed and gently compress the seed into the seedbed. When operating the Power Rake with Seeder attached, the rake should not be angled. The end plates should be mounted in working position. Use the top three point adjustment link to control roller depth, which will also determine pressure on the packer drum, which firms the seedbed. NOTICE Follow the Operational Procedures outlined in the Power Rake Operator s Manual for proper operation. POWER RAKE PRE-INSTALLATION. The seeder is mounted to the back of the frame where the gauge wheels normally are. Remove the gauge wheel assemblies from the rake. Attach the lift arms to the frame to dimensions shown (See Figure ). Install caster fork assembly into detachable caster arms (See Figure 7). 2. Replace the barrier adjustment bar with curved bar. ATTACHING SEEDER TO HARLEY POWER RAKE Move tractor and rake into position in front of the seeder. Move back slowly and carefully, not allowing anyone to be between the rake and the seeder until receivers are in position to lift seeder. Carefully raise rake until hooks on seeder are fully engaged. Turn off tractor engine. Install the 3/4 pins to secure the seeder. Raise jackstand and secure in operating position. POWER RAKE ROLLER RPM The RPM of the Power Rake roller will determine the flow of soil over the roller and how far it pitches the soil toward the packer drum. As the seed is dropped into this soil flow, the amount of exposed seed percentage is determined by location of soil flow over the roller in relation to seed drop zone. To get more seed exposed, slow the RPM of the roller to allow seed to be dropped. Start with tractor tachometer at 00 rpm and work up to find optimal seed to soil contact. BERM LEVELERS Excessive material may pass over the ends of the roller, creating a ridge which will leave an uneven seedbed. Lower the berm levelers to spread this material out. 12 MODEL PS5 & PS HARLEY POWER SEEDER
OPERATIONAL PROCEDURE Figure 2. Berm Adjustments MODEL PS5 & PS HARLEY POWER SEEDER
OPERATIONAL PROCEDURE SEED RATE ADJUSTMENT When properly adjusted, the holes in the slide should line up with the holes in the box, with the control handle set at. To make an adjustment, loosen the control handle on the box, move the slide until the holes line up. When the handle is moved to 0 the holes in the box should be completely covered. If the holes are not covered, loosen the three bolts holding the seedmeter casting and shift it slightly so that the 0 mark is farther from the control handle. Retighten the bolts. Move control handle to 0. Holes in the box should then be completely covered. NOTICE When changing seed rate always move control handle to 0 then to new value. Figure 3. Seed Rate Adjustment 14 MODEL PS5 & PS HARLEY POWER SEEDER
OPERATIONAL PROCEDURE To double the seed rate in this chart, the pulleys must be reversed.. 2. 3. Remove the belt. Remove the hex bolt securing each pulley and remove pulleys. Reassemble with the 5-1/2 pulley on the packer drum. Note, 5-1/2 pulley must also be flipped (hub side out) and the 4 pulley flipped (hub side in) to maintain belt alignment. Figure 4. Seed Rate MODEL PS5 & PS HARLEY POWER SEEDER
Shutting Down Stop equipment. OPERATIONAL PROCEDURE Lower the lift arms and power rake to the ground. Purge any air in the system. Hydraulic system leakdown, hydraulic system failures, mechanical failures, or movement of control levers can cause equipment to drop or rotate unexpectedly. Shut off engine, set brake, remove key, and remove seat belt before leaving the tractor operator s seat. Do not disconnect hydraulic lines until all system pressure is relieved. Lower unit to ground, stop engine, and operate all hydraulic control levers. REMOVING SEEDER FROM POWER RAKE Lower jack stands to storage position. Remove the seeder attachment pins. On a hard level surface, lower seeder to the ground. Carefully drive away from seeder, watching that the lift hooks have cleared the attachment arms. STORAGE Make sure the disconnected seeder is stored on a hard, level surface. Block equipment securely for storage. Keep children and bystanders away from storage area. MAINTENANCE Grease packer drum bearings 1-2 pumps with #2 lithium with moly weekly. Check belt for signs of wear or misalignment monthly. Clean out seed box after each job. Inspect and clean safety decals. CHANGING AGITATOR BLADES Agitator blades are supplied as standard on your seed box. They should operate leaving a slight clearance with the bottom of the seed box. 1 MODEL PS5 & PS HARLEY POWER SEEDER
MAINTENANCE NOTICE Before proceeding with any agitator installation, be sure to note the direction of shaft rotation on your seeder.. 2. 3. 4. Figure 5. Agitator Blades Remove drive pulley. Remove two capscrews (inside the box) which hold end bearing on right end of right seed box. Slide shaft out of right end. Agitators should be installed with careful attention to the direction of shaft rotation as seed rate will be reduced if they run backwards. MODEL PS5 & PS HARLEY POWER SEEDER 17
ASSEMBLY - RAKE & SEEDER Figure 7. Rake & Seeder Assembly 1 MODEL PS5 & PS HARLEY POWER SEEDER
ASSEMBLY - SEEDER/CASTER BRACKET 5 9. 42.94 Figure. Caster Placement 5 MODEL PS5 & PS HARLEY POWER SEEDER 19
ASSEMBLY - seeder 5 Diagram 1 of 2 33 40 A 1 32 20 35 1 17 14 3 31 2 24 STAND IN THE DOWN POSITION REPLACED COTTER PIN 1 10 30 32 4 22 14 1 17 3 9 24 43 2 35 REPLACES SQ. BUSHING IN SEED BOX STAND IN THE UP POSITION 3 19 4 21 39 41 5 1/2" PULLEY ON TOP A 40 11 3 27 1 33 44 23 1 2 42 7 42 7 37 33 29 22 5 9 34 9 45 12 14 25 20 MODEL PS5 & PS HARLEY POWER SEEDER
ITEM Part Qty DESCRIPTION ASSEMBLY - seeder 5 List 1 of 2 1. 07-0204 2 Pin, Roll, Gr2, 1/4 x 2 2. 07-0205 2 Pin, Cotter, Gr2, 1/ x 1 3. 07-0 1 Washer, Machined, 1 3/4-1 1/ 4. 07-1279 1 Screw, Set, Gr5, 3/-1 x 3/4 5. 07-1714 1 Screw, HHC, Gr, 5/1-1 x 1. 07-171 9 Washer, Lock, Split, Medium, 3/ 7. 07-110 3 Nut, Hex, Lock, Gr, 5/1-1. 07-211 9 Screw, HHC, Gr, 3/-1 x 1 1/4 9. 07-2300 4 Washer, Flat, CL., M1 10. 07-243 1 Pin, Klik, 3/1 x 1 1/4 11. 07-3272 1 Nut, Hex, Jam, Gr, 3/-1 12. 07-3432 1 Screw, HHC, Gr, 1/4-20 x 3/4. 07-359 14 Screw, HHC, Gr, 3/-1 x 2 3/4 14. 07-403 9 Washer, Lock, Split, Medium, 1/4. 07-5370 14 Nut, Hex, Lock, Gr, 3/-1 1. 07-735 Screw, HHC, Gr, 1/4-20 x 1/2 17. 07-7407 2 Cap, Tube, Round, 1.0 1. -1430 2 Key, 1/4 x 1 1/4 19. M1001 1 Weld, Panel, Side, Left 20. M10019 1 Weld, Panel, Side, Right 21. M10023 1 Shaft, Extension 22. M10033 2 Bearing, Spacer 23. M1003 1 Tension, Arm 24. M10037 2 Assembly, Comb, Lift 25. M10039 1 Weld, Shield, Side 2. M10040 1 Pulley, 4 Inch, with Hub 27. M10041 1 Pulley, 5.5 Inch, with Hub 2. M1001 1 Weld, Main Frame 29. M1004 1 Weld, Packer, Drum 30. M10070 1 Weld, Seed, Baffle 31. M1001 2 Weld, Bracket, Lift 32. M1002 2 Weld, Stand, Seeder 33. M5009-2 3 Washer, 1/ x 1 3/4 x /32 34. M5444 1 Roller, Tension 35. M44 2 Weld, Handle MODEL PS5 & PS HARLEY POWER SEEDER 21
ASSEMBLY - seeder 5 Diagram 2 of 2 33 40 A 1 32 20 35 1 17 14 3 31 2 24 STAND IN THE DOWN POSITION REPLACED COTTER PIN 1 10 30 32 4 22 14 1 17 3 9 24 43 2 35 REPLACES SQ. BUSHING IN SEED BOX STAND IN THE UP POSITION 3 19 4 21 39 41 5 1/2" PULLEY ON TOP A 40 11 3 27 1 33 44 23 1 2 42 7 42 7 37 33 29 22 5 9 34 9 45 12 14 25 Figure. Seeder Assembly 5 22 MODEL PS5 & PS HARLEY POWER SEEDER
ASSEMBLY - seeder 5 List 2 of 2 ITEM QTY PART NO. DESCRIPTION 3. M55 2 Assembly, Barrie Pin 37. M30 1 Bushing, Pivot 3. M23 2 Weld, Jack, Pin, 5/ x 3 5/ 39. P0000 1 Bearing, Insert 40. P007900 2 Flange, Bearing, 1 1/ 41. P03003 1 V-Belt, B-3 42. P110512 2 Screw, Socket Head, Gr, 5/1-1 x 3 43. P04500 2 Spring, Compression, 3 Inch 44. P0400 1 Spring, Extension 45. P952224 1 Snap Ring, Heavy, 5/ 4. P90001 1 Box, Seeder, Brillion, 5Ft MODEL PS5 & PS HARLEY POWER SEEDER 23
ASSEMBLY - seeder box 5 27 3 2 1 9 23 1 17 5 12 10 19 20 11 24 9 7 5 22 4 14 25 2 1 22 11 21 19 22 11 2 CORRECT AGITATOR ORIENTATION 25 22 29 22 20 Figure 9. Seeder Box 5 24 MODEL PS5 & PS HARLEY POWER SEEDER
ASSEMBLY - seeder box 5 PARTS LIST ITEM part qty DESCRIPTION 1. 07-000 4 Screw, Phillips, Gr2, 10-24 x 1 2. 07-0140 4 Washer, Lock, Gr2, 10 3. 07-0141 4 Nut, Hex, Gr2, 10-24 4. 07-0 1 Washer, Flat, Gr, 1/2 5. 07-09 2 Screw, HHC, Gr, 1/2- x 1 1/4. 07-05 1 Screw, Set, Gr2, 1/4-20 x 3/4 7. 07-1714 1 Screw, HHC, Gr, 5/1-1 x 1. 07-172 2 Washer, Lock, Split, Medium, 1/2 9. 07-174 2 Nut, Hex, Gr, 1/2-10. 07-324 1 Nut, Wing, 3/-1 11. 07-3273 Washer, Lock, Split, Medium, 5/1 12. 07-3279 1 Washer, Flat, Gr, 3/. 07-343 Screw, HHC, Gr, 5/1-1 x 3/4 14. 07-370 1 Screw, HHC, Gr, 1/2- x 1. 07-34 3 Washer, Flat, Gr, 7/ 1. 07-7424 1 Plate, Shifter, Right 17. 07-7425 1 Handle, Shifter 1. 07-7429 2 Latch, Rubber 19. 07-7430 2 Bushing, Square Hole 20. 07-7431 2 Bearing, Housing, End 21. 07-7432 1 Bearing, Hosing, Intermediate 22. 07-7433 5 Washer,.0747 x 2.75, with Square Hole 23. 07-7434 1 Bolt, Square Head, 3/-1 x 1 24. 07-7435 2 Cover, Lock Assembly 25. 07-7441 2 Blade, Agitator 2. 07-7442 1 Shaft, Square, 5 Ft 27. 07-7443 1 Cover, 5 Ft 2. 07-7444 1 Hopper, Seedbox, 5 Ft 29. P0000 1 Bearing, Insert, 1 Inch MODEL PS5 & PS HARLEY POWER SEEDER 25
notes 2 MODEL PS5 & PS HARLEY POWER SEEDER
ASSEMBLY - SEEDER/CASTER BRACKET Figure 10. Caster Placement MODEL PS5 & PS HARLEY POWER SEEDER 27
ASSEMBLY - seeder Diagram 1 of 2 32 A 40 1 31 17 34 14 1 2 30 21 3 STAND IN THE DOWN POSITION REPLACED COTTER PIN 19 10 4 24 1 23 31 17 3 1 9 14 2 43 34 2 REPLACES SQ. BUSHING IN SEED BOX STAND IN THE UP POSITION 3 20 4 22 39 41 5 1/2" PULLEY ON TOP A 40 11 1 29 3 32 42 5 44 7 1 42 25 37 24 32 2 7 35 9 33 9 45 14 27 12 Figure 11. Seeder Assembly 2 MODEL PS5 & PS HARLEY POWER SEEDER
ITEM part qty DESCRIPTION ASSEMBLY - seeder List 1 of 2 1. 07-0204 2 Pin, Roll, Gr2, 1/4 x 2 2. 07-0205 2 Pin, Cotter, Gr2, 1/ x 1 3. 07-0 1 Washer, Machined, 1 3/4-1 1/ 4. 07-1279 1 Screw, Set, Gr5, 3/-1 x 3/4 5. 07-1714 1 Screw, HHC, Gr, 5/1-1 x 1. 07-171 9 Washer, Lock, Split, Medium, 3/ 7. 07-110 3 Nut, Hex, Lock, Gr, 5/1-1. 07-211 9 Screw, HHC, Gr, 3/-1 x 1 1/4 9. 07-2300 4 Washer, Flat, CL., M1 10. 07-243 1 Pin, Klik, 3/1 x 1 1/4 11. 07-3272 1 Nut, Hex, Jam, Gr, 3/-1 12. 07-3432 1 Screw, HHC, Gr, 1/4-20 x 3/4. 07-359 14 Screw, HHC, Gr, 3/-1 x 2 3/4 14. 07-403 9 Washer, Lock, Split, Medium, 1/4. 07-5370 14 Nut, Hex, Lock, Gr, 3/-1 1. 07-735 Screw, HHC, Gr, 1/4-20 x 1/2 17. 07-7407 2 Cap, Tube, Round, 1.0 1. -1430 2 Key, 1/4 x 1 1/4 19. M10001 1 Weld, Frame, Main, Seeder, Ft 20. M1001 1 Weld, Panel, Side, Left 21. M10019 1 Weld, Panel, Side, Right 22. M10023 1 Shaft, Extension 23. M10030 1 Weld, Baffle, Seed 24. M10033 2 Bearing, Spacer 25. M1003 1 Tension, Arm 2. M10037 2 Assembly, Comb, Lift 27. M10039 1 Weld, Shield, Side 2. M10040 1 Pulley, 4 Inch, with Hub 29. M10041 1 Pulley, 5.5 Inch, with Hub 30. M1001 2 Weld, Bracket, Lift 31. M1002 2 Weld, Stand, Seeder 32. M5009-2 3 Washer, 1/ x 1 3/4 x /32 33. M5444 1 Roller, Tension 34. M44 2 Weld, Handle 35. M479 1 Weld, Packer Drum MODEL PS5 & PS HARLEY POWER SEEDER 29
ASSEMBLY - seeder Diagram 2 of 2 32 A 40 1 31 17 34 14 1 2 30 21 3 STAND IN THE DOWN POSITION REPLACED COTTER PIN 19 10 4 24 1 23 31 17 3 1 9 14 2 43 34 2 REPLACES SQ. BUSHING IN SEED BOX STAND IN THE UP POSITION 3 20 4 22 39 41 5 1/2" PULLEY ON TOP A 40 11 1 29 3 32 42 5 44 7 1 42 25 37 24 32 2 7 35 9 33 9 45 14 27 12 Figure 11. Seeder Assembly 30 MODEL PS5 & PS HARLEY POWER SEEDER
ITEM part qty DESCRIPTION ASSEMBLY - seeder List 2 of 2 3. M55 2 Assembly, Barrie Pin 37. M30 1 Bushing, Pivot 3. M23 2 Weld, Jack, Pin, 5/ x 3 5/ 39. P0000 1 Bearing, Insert 40. P007900 2 Flange, Bearing, 1 1/ 41. P03003 1 V-Belt, B-3 42. P110512 2 Screw, Socket Head, Gr, 5/1-1 x 3 43 P04500 2 Spring, Compression, 3 Inch 44. P0400 1 Spring, Extension 45. P952224 1 Snap Ring, Heavy, 5/ 4. P90000 1 Box, Seeder, Brillion MODEL PS5 & PS HARLEY POWER SEEDER 31
ASSEMBLY - seeder box 2 1 3 24 25 27 29 17 9 2 1 19 5 12 10 5 11 22 4 14 7 1 23 27 11 2 24 27 21 22 27 11 CORRECT AGITATOR ORIENTATION 2 24 27 22 20 27 11 27 25 30 Figure 12. Seeder Box 32 MODEL PS5 & PS HARLEY POWER SEEDER
ASSEMBLY - seeder box PARTS LIST ITEM part qty DESCRIPTION 1. 07-000 4 Screw, Phillips, Gr2, 10-24 x 1 2. 07-0140 4 Washer, Lock, Gr2, 10 3. 07-0141 4 Nut, Hex, Gr2, 10-24 4. 07-0 1 Washer, Flat, Gr, 1/2 5. 07-09 2 Screw, HHC, Gr, 1/2- x 1 1/4. 07-05 1 Screw, Set, Gr2, 1/4-20 x 3/4 7. 07-1714 1 Screw, HHC, Gr, 5/1-1 x 1. 07-172 2 Washer, Lock, Split, Medium, 1/2 9. 07-174 2 Nut, Hex, Gr, 1/2-10. 07-324 1 Nut, Wing, 3/-1 11. 07-3273 11 Washer, Lock, Split, Medium, 5/1 12. 07-3279 1 Washer, Flat, Gr, 3/. 07-343 11 Screw, HHC, Gr, 5/1-1 x 3/4 14. 07-370 1 Screw, HHC, Gr, 1/2- x 1. 07-34 3 Washer, Flat, Gr, 7/ 1. 07-7422 1 Hopper, Seedbox, Ft 17. 07-7423 1 Cover, Ft 1. 07-7424 1 Plate, Shifter, Right 19. 07-7425 1 Handle, Shifter 20. 07-742 1 Shaft, Square 21. 07-7427 1 Spacer, Blade 22. 07-742 3 Blade, Agitator, 22.5 Inches 23. 07-7429 2 Latch, Rubber 24. 07-7430 3 Bushing, Square Hole 25. 07-7431 2 Bearing, Housing, End 2. 07-7432 2 Bearing, Hosing, Intermediate 27. 07-7433 7 Washer,.0747 x 2.75, with Square Hole 2. 07-7434 1 Bolt, Square Head, 3/-1 x 1 29. 07-7435 2 Cover, Lock Assembly 30. P0000 1 Bearing, Insert, 1 Inch MODEL PS5 & PS HARLEY POWER SEEDER 33
ASSEMBLY - OPTIONAL 3PT HITCH 10 1 9 2 10 4 5 3 2 9 2 9 7 1 5 4 3 Figure. 3PT Hitch Assembly ITEM part qty DESCRIPTION 1. 07-0205 2 Pin, Cotter, Gr2, 1/ x 1 2. 07-2300 2 Washer, Flat, CL., M1 3. 07-35 2 Screw, HHC, Gr, 3/-1 x 1 3/4 4. 07-5370 2 Nut, Hex, Lock, 3/-1, Gr 5. M1004 2 Weld, Stand, Clamp. M10047 1 Weld, Tractor 3 Point Mount 7. M1009 1 Assembly, Tine Bar, 5FT M1005 1 Assembly, Tine Bar, FT. M23 2 Weld, Jack Pin, 5/ x 3 5/ 9. P04500 2 Spring, Compression, 3 Inch 10. P95501 2 Plug, Tube, 1 1/2 34 MODEL PS5 & PS HARLEY POWER SEEDER
ASSEMBLY - optional tine bar 3 1 4 5 2 Figure 14. Tine Bar Assembly M1009 5 FT ITEM part qty DESCRIPTION 1. M10090 1 Tine Tube, Horizontal 2. 07-357 14 Screw, HHC, Gr, 3/-1 x 2 3. 07-5370 14 Nut, Hex, Lock, St, Gr, 3/-1 4. P704100 14 Tine Coil,.31 x 9.4 5. 07-3275 14 Washer, Flat, Gr, 5/1 M1005 FT ITEM part qty DESCRIPTION 1. M10055 1 Tine Tube, Horizontal 2. 07-357 1 Screw, HHC, Gr, 3/-1 x 2 3. 07-5370 1 Nut, Hex, Lock, St, Gr, 3/-1 4. P704100 1 Tine Coil,.31 x 9.4 5. 07-3275 1 Washer, Flat, Gr, 5/1 MODEL PS5 & PS HARLEY POWER SEEDER 35
ASSEMBLY - OPTIONAL bracket kit 2 1 1 2 3 ITEM part qty DESCRIPTION Figure. Bracket Kit 5 Ft 1. M10011 2 Weld, Caster, Support, Arm 2. M10022 2 Assembly, Lock, Arm 3. M10073 1 Manual, Adjustment Bar 3 2 2 3 4 4 1 ITEM part qty DESCRIPTION Figure 1. Bracket Kit Ft 1. M10009 1 Weld, Barrier, Adjustment Arm 2. M10011 2 Weld, Caster, Support, Arm 3. M10022 2 Assembly, Lock, Arm 4. P95550 2 Cap, Square, 1/2 x 3 3 MODEL PS5 & PS HARLEY POWER SEEDER
WARRANTY POLICY Harley Attachments, LLC warrants its line of Harley equipment to be free from defects in material and factory workmanship for a period of twelve (12) months. Exception to this warranty period will be Harley Rock Pickers, which will carry a six () month warranty. Warranty registration form must be filled out, signed by the customer, and returned to Harley Attachments, LLC within thirty (30) days from the date of purchase before any warranty claim will be considered. Dealer rental units are considered sold units and the same warranty policy applies. This warranty is limited exclusively to equipment manufactured by Harley Attachments, LLC and is subject to inspection by Harley Attachments, LLC to identify the nature and cause of failure. This company in no way warrants belts, bearings, hydraulics, chains, sprockets, tires, or any other trade accessory not manufactured by Harley Attachments, LLC since these items are warranted separately by their respective manufactures. This warranty shall become void if, in the best judgement of Harley Attachments, LLC, the equipment has been subject to misuse, negligence, alterations, and damage by accident or lack of required maintenance or if the product has been used for a purpose for which it was not intended. Wear items such as, but not limited to, rollers and drive chains will not be covered under warranty. Normal wear depreciation is not covered by warranty. Claims for equipment damaged in transit should be referred to the freight carrier. Harley Attachments, LLC will not be responsible for damages incurred in transit. Harley Attachments, LLC obligations under this warranty shall be limited to repair or replacement at its option of the equipment or trade accessories as they conform to this policy. Trade accessories such as but not limited to bearings, tires and wheels, etc will be sent to the respective manufacturer for warranty consideration. Any warranty reimbursement as related to these items will rely solely on the decision of each separate manufacture including Harley Attachments, LLC. Reimbursement on parts will be at dealer net and labor allowances are calculated according to Harley Attachments, LLC s predetermined flat time and rate. Freight charges and misc. shop supplies are not covered under warranty. Dealer s responsibility is to fully explain the warranty policy to the customer before starting any repairs. Return the defective parts (prepaid) along with a completed Harley Attachments, LLC warranty form. All replacement parts used in warranty must be furnished by Harley Attachments, LLC (please refer to warranty procedures). The selling dealer has no authority to make any representation or promise on behalf of Harley Attachments, LLC or to modify the terms or conditions of this warranty in any way. Owner s responsibility is to complete and return the warranty registration within thirty (30) days from the date of purchase. Operate and maintain the equipment according to the recommendations in the owner s manual. The owner is responsible for freight and transportation to and from the dealership or any service calls made by the dealer. This warranty is subject to any conditions of supply, which may directly affect our ability to obtain materials or manufacture replacement parts. Harley Attachments, LLC reserves the right to make improvements in design or change in specifications of its products without notice and is not obligated to make the same improvements to equipment previously manufactured. THERE IS NO OTHER EXPRESSED OR IMPLIED WARRANTY ON THIS PRODUCT OR ON ITS MERCHANTABILITY OR ON ITS FITNESS. TO THE EXTENT ALLOWED BY LAW NEITHER HARLEY ATTACHMENTS, LLC NOR THE SELLING HARLEY DEALER SHALL HAVE ANY RESPONSIBILITY FOR LOSS OF USE OF THE PRODUCT, LOSS OF TIME, INCONVENIENCE, COMMERCIAL LOSS, OR CONSEQUENTIAL DAMAGES. MODEL PS5 & PS HARLEY POWER SEEDER 37
Harley Attachments, LLC 105 2nd Avenue SW Jamestown, ND 5401 00-437-9779 Phone 701-252-197 Fax 701-952-9307 Parts Fax Email: harleycs@paladinbrands.com Web: www.paladinbrands.com