INSTLLTION INSTRUTIONS FOR PRT 99-90 KIT FETURES DIN Head Unit Provision with pocket ISO Head Unit Provision with pocket Double DIN Head Unit Provision ISO Stacked Head Unit Provision KIT OMPONENTS pplications VW 009-0/EOS 007-0/New Jetta 005-0 GLI 008-0/GTI 006-0/Passat 006-0 Rabbit 006-09/R 008/Tiguan 009-0 Golf 00 99-90 ) Radio Housing ) ISO rackets ) ISO Trim Plate D) DDIN rackets E) DDIN Trim Plate F) Pocket D F E WIRING ND NTENN ONNETIONS (Sold Separately) Wire harness: XSVI-900-NV VW Interface 00-up ntenna adapter: 0-EU55-adapter for amplified antenna 00-up TOOLS REQUIRED: T-0 Torx Screwdriver Flat lade Screwdriver Or Panel Removal Tool -800--09 www.metraonline.com OPYRIGHT 00-00 METR ELETRONIS ORPORTION
99-90 TLE OF ONTENTS Dash Disassembly - GLI 008-0..., - GTI 006-09..., - New Jetta 005-0..., - Rabbit 006-09..., - R 008..., - 009-0... - Passat 006-0... - Golf 00, GTI 00, Jetta Sport Wagon... - Tiguan 009-0... - Eos 007-0... 5 Kit ssembly: - DIN Head Unit Provision with Pocket...6 - ISO Head Unit Provision with Pocket...7 - Double DIN Head Unit Provision...8 - Stacked ISO Head Unit Provision...9 Final ssembly...0 KNOWLEDGE IS POWER Enhance your installation and fabrication skills by enrolling in the most recognized and respected mobile electronics school in our industry. Log onto www.installerinstitute.com or call 800-5-678 for more information and take steps toward a better tomorrow. Metra reccommends MEP certified technicians.
99-90 DSH DISSSEMLY NEW JETT 005-0/GLI 008-0 GTI 006-09/RIT 006-09 R 008 Disconnect the negative battery terminal to prevent an accidental short circuit. Unclip and remove the grille from the top-center of dash. (Figure ) Remove one T-0 torx screw from black insert from under grille removed in step one. (Figure ) Remove insert. (Figure ) 5 Remove two T-0 torx screws from under black insert removed in step two. (Figure D) D
99-90 DSH DISSSEMLY NEW JETT 005-0/GLI 008-0 GTI 006-09/RIT 006-09 R 008 6 Unsnap and remove the vent assembly above the radio. (Figure E) E 7 Remove two T-0 torx screws from top sides of radio/climate panel. (Figure F) 8 Remove panel. (Figure G) 9 Remove four T-0 torx screws to remove the radio. (Figure H) F H G
99-90 DSH DISSSEMLY 009-0 / PSST 006-0 JETT SPORT WGON 00 GOLF 00 / GTI 00 Disconnect the negative battery terminal to prevent an accidental short circuit. Unclip and remove trim panel surrounding radio. (Figure ) FM 0.7MHZ FM M D Remove () T-0 Torx screws to remove radio. ON VOL SS TRE L FD PSSENGER IR G OFF SN TUNE 7 80 6
99-90 DSH DISSSEMLY TIGUN 009-0 Disconnect the negative battery terminal to prevent an accidental short circuit. Unclip and remove passenger air bag light panel to the right of the hazard light button. (Figure ) PSSENGER IR G PSSENGER IR G Unclip and remove the panel with the two slots in it to the left of the hazard light button. (Figure ) Remove () T-0 Torx screws exposed behind the two panels removed in the two previous steps. (Figure ) 5 Unclip and remove the trim panel surrounding the radio. (Figure ) PSSENGER IR G 6 Remove () T-0 Torx screws securing the radio. Unplug and remove the radio. (Figure D) D F F
99-90 DSH DISSSEMLY EOS 007-00 Disconnect the negative battery terminal to prevent an accidental short circuit. Unclip and remove the radio trim panel. (Figure ) Remove the () screws securing the radio. Unplug and remove the radio. (Figure ) 5
99-90 KIT SSEMLY DIN HED UNIT PROVISION WITH POKET Slide the DIN cage into the Radio Housing and secure by bending the metal locking tabs down. (Figure ) Slide the aftermarket head unit into the cage and secure. (Figure ) Snap the pocket into the radio housing. (Figure ) 6
99-90 KIT SSEMLY ISO HED UNIT PROVISION WITH POKET Mount the ISO rackets to the head unit with the screws supplied with the unit. (Figure ) Slide the head unit into the radio opening until the side clips engage. (Figure ) Snap the ISO Trim Plate into the Radio Housing. (Figure ) Snap the pocket into the radio housing. (Figure ) 7
99-90 KIT SSEMLY DOULE DIN HED UNIT PROVISION ut and remove center divide from radio housing. (Figure ) Snap the DDIN brackets to the inside edge of the radio housing. (Figure ) Slide the DDIN radio unit into the DDIN bracket/radio housing assembly and secure the unit to the kit using the screws supplied with the head unit. (Figure ) Snap the DDIN trim-plate onto the housing/radio assembly. (Figure ) 8
99-90 KIT SSEMLY STKED ISO HED UNIT PROVISION ut and remove center divider from radio housing. (Figure ) Snap the DDIN brackets to the inside edge of the radio housing. (Figure ) Slide the stacked ISO DIN units into the DDIN bracket/radio housing assembly and secure the units to the kit using the screws supplied with the head units. (Figure ) Snap the DDIN trim-plate onto the housing/radio assembly. (Figure ) 9
99-90 FINL SSEMLY FINL SSEMLY ) Strip wire ends back /" ) Twist ends together ) Solder D) Tape D Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter and making connections as shown. (Isolate and individually tape off the ends of any unused wires to prevent electrical short circuit.) Re-connect the negative battery terminal and test the unit for proper operation. Reassemble in reverse order of disassembly. FINL WIRING ONNETIONS Make wiring connections using the EI color code chart shown below and the instructions included with the head unit. Metra recommends making connections as shown below; Strip, Splice, Solder, Tape. Isolate and individually tape off ends of any unused wires to prevent electrical short circuit. METR / EI WIRING ODE V Ignition / cc... Red Right Front (+)..... Gray V att / Memory.. Yellow Right Front (-)...... Gray/ lack Ground........... lack* Left Front (+)...... White Power ntenna..... lue Left Front (-)....... White / lack mp Turn-On...... lue / White Right Rear (+)...... Violet mp Ground....... lack / White Right Rear (-)...... Violet / lack Illumination........ Orange Left Rear (+)....... Green Dimmer.......... Orange / White Left Rear (-)....... Green / lack *NOTE: When a lack wire is not present, ground radio to vehicle chassis. ll colors may not be present on all leads due to manufacturer s specifications. -800--09 0 www.metraonline.com REV. 0/6/0 OPYRIGHT 00-00 METR ELETRONIS ORPORTION INST99-90