X-MULTI
5. Kratki uvod u instalaciju: Postavljanje X-MULTI --Instala Instalacijska procedura (za detaljnije upute vidi instalacijski priručnik): Odreñivanje mjesta instalacije Educiranje kupca o pravilnom načinu korištenja klima ureñaja. Polaganje instalacija i ožičenje Provjera rada ureñaja u hlañenju i grijanju Instalacija unutarnjih i vanjske jedinice Adresiranje unutarnjih jedinica Spajanje instalacija na pravi način Provjera napona: : 230V±10% Provjera cijele instalacije prije vakuumiranja Refrigerant system and electric system Vakuumiranje i eventualna nadopuna sustava
--Va Važne napomene kod instalacije: Postavljanje X-MULTI 1) za meñuvezu obavezno koristiti oklopljeni kabel; 2) instalater mora vakuumirati sustav kako bi se provjerilo eventualno curenje; 3) prije spajanja napojnih kablova i pokretanja ureñaja aja, potrebno je provjeriti je li napon u granicama 230V±10%; 4) sustav se uvijek dopunjava s R410A u tekućem em stanju; 5) prije pokretanja sustava potrebno se uvjeriti da su unutarnje jedinice pravilno adresirane Refrigerant system and electric system
Postavljanje X-MULTI Adresiranje unutarnjih jedinica Indoor address setting
Postavljanje X-MULTI Dva su načina adresiranja: Indoor address setting
Postavljanje X-MULTI Pomoću daljinskog upravljača (default) A. Korištenje daljinskog upravljača B. Korištenje dip switch-eva na PCB-ima unutarnjih jedinica. 2. Procedura adresiranja korištenjem daljinskog upravljača. A. Adresiranje se obavlja tek po uspješnoj instalaciji i ožičenju, te otvaranju svih ventila B. Uvjerite se da unutarnje i vanjska jedinica istog sustava koriste isti izvor napajanja; C. Postavljanje svih jedinica u standby mode; D. Adrese podesiti kako slijedi: Unutarnja jedinica na ventilu A, mora imati adresu 1; Unutarnja jedinica na ventilu B, mora imati adresu 2; Unutarnja jedinica na ventilu C, mora imati adresu 3; Unutarnja jedinica na ventilu D, mora imati adresu 4; Indoor address setting
E. Primjer: podesite jedinicu A na adresu 1.Pritisnite i držite emergency switch u trajanju oko 15 sekundi, oglasit će se 4 puta (PI PI PI PI) i tada pustite prekidač. Unutarnja jedinica počela je s procedurom adresiranja. F. Koristeći daljinski upravljač uključite un. jedinicu. Status se mijenja iz OFF u ON i TIMER LED jednom zatreptičime se potvrñuje početak procedure adresiranja. G. Pritisnite "SLEEP " na daljinskom upravljaču, broj pritisaka odreñuje adresu koju želite podesiti, i to kako slijedi: Pritisnite " SLEEP " jednom, adresa je "1 ", i TIMER LED zatrepti jednom; Pritisnite " SLEEP " dva puta, adresa je 2 ", i TIMER LED zatrepti dva puta Pritisnite " SLEEP " tri puta, adresa je 3 ", i TIMER LED zatrepti tri puta Pritisnite " SLEEP " četiri puta, adresa je 4 ", i TIMER LED zatreptičetiri puta H. Daljinskim upravljačem ugasite ureñaj. Status se mijenja iz ON u OFF. I izlazi se iz procedure adresiranja, adrese ostaju memorirane. LED board će pokazivati adresu unutarnje jedinice dok se sustav ne ugasi. I. Za promjenu adrese ponovite korake od E do G. J. Nakon adresiranja isključite i ponovno uključite sustav čime se isti aktivira. K. Po uspješnom adresiranju izbjegavajte naknadne promjene kako bi se izbjegli potencijalni problemi. Indoor address setting Postavljanje X-MULTI
Postavljanje X-MULTI Drugi način adresiranja AB TIPOVI: Procedura adresiranja korištenjem DIP switch SW01 and SW03. SW01-7 ON: Adresiranje un. jedinica preko DIP switch-eva; OFF: Adresiranje preko daljinskog upravljača Indoor address setting
Postavljanje X-MULTI Indoor address setting
Postavljanje X-MULTI Indoor address setting
Postavljanje X-MULTI Indoor address setting
Postavljanje X-MULTI Važno: Unutarnje jedinice moraju biti adresirane kao 1,2,3, odozdo prema dolje, u suprotnom sustav neće raditi kako treba. 4. Kako provjeriti adrese? Po završetku postupka adresiranja, isključite i ponovno uključite struju ali ostavite sve unutarnje jedinice u stand-by modusystem but set all the indoor units in STANDBY. Zatim pritisnite emergency switch dok ne čujete zvono 5 puta (Pi Pi Pi Pi), a na TIMER LED displayu tada možete očitati adresu unutarnje jedinice. Pritiskom na bilo koju tipku daljinskog upravljača, izlazite iz procedure provjere adresa unutarnjih jedinica. Indoor address setting
2. Dijagram rashladnog kruga: Postavljanje X-MULTI --di dijagram (AU182XFERA / AU222XFERA): TOCI B A Refrigerant system and electric system
Postavljanje X-MULTI --di dijagram (AU282XHERA / AU362XHERA): TOCI B A Refrigerant system and electric system
Postavljanje X-MULTI 3. Strujna shema i objašnjenje pojedinih električnih dijelova: --Strujna shema vanjske jedinice (AU182XFERA / AU222XFERA): TOCI TC TS TA TD TE CAPACITOR-1 CN1 CN23 TO SPDU CN22 CN21 CN2 N CN3 CONTROL CIRCUIT BOARD AC FAN MOTOR M L M H Y/G CRANKCASE HEATER CN4 SV2 4WV CN6 CN7 CN5 FUSE1 250VAC T3.15A start/up stop/down SW1 SW2 SW3 SW4 ON 4-WAY VALVE LED2 LED1 1234 5678 SW5 CN8 N CN9 L CN10 BUS CN11 PTC CN12 LED CN26 LED1 LED2 DIAGNOSE PCB LED3 ON LED4 1 2 3 4 SW5 LED5 REACTOR CAPACITOR-2 - + BL OR RO P(+) ACN N(-) SPDU RI ACL U U R V W W B V W CN20CN19 HP LP CN18 PMV_A CN17 PMV_B CN16 PMV_C CN15 PMV_D CN14 DEBUG_LED CN13 COMPRESSOR M M M R R CN7 RL1 CN8 CN2 FUSE T25A 250VAC 220VAC-L CN1 CN5 CN4 CN3 220VAC-N POWER CIRCUIT BOARD TOCI PIPING TEMPERATURE SENSOR TC CONDENSING TEMPERATURE SENSOR TS: COMPRESSOR INHALE SENSOR TA AMBIENT TEMPERATURE SENSOR TD: COMPRESSOR VENT SENSOR TE DEFROSTING TEMPERATURE SENSOR OR : ORANGE B : BLACK BL : BLUE Y/G : YELLOW/GREEN R : RED W : WHITE Refrigerant system and electric system W B Y/G B W N L C1C2 L N Y/G To Indoor Units To Power Supply
W4 ON 1 2 3 4 567 8 SW5 Postavljanje X-MULTI Dip 1: odabir motora ventilatora Dip 2: odabir vrijednosti defrosta Dip 5~6: odabir modela Dip 8: odabir tihog načina rada CN26 LED1 LED2 DIAGNOSE PCB LED3 ON LED4 1 2 3 4 SW5 LED5 Dip 1 ON: prisilno grijanje Dip 2 ON: prisilno hlañenje Dip 3 ON: grijanje Dip 4 ON: hlañenje Normal status (ne radi): sve isključeno Refrigerant system and electric system
4. Uvod u glavne funkcije: --Pokretanje kompresora. Postavljanje X-MULTI Postoje dvije vrste pokretanja kompresora ovisno o stanju sustava To su HOT START i SOFT START.Kako bi se sigurnije pokrenuo kompresor nakon dužeg mirovanja, koristit će e se SOFT START, glavni razlog je izbjegavanje povrata tekućine kod starta. U protivnom koristit će e se HOT START. SOFT START procedura: : max. 6 minuta Refrigerant system and electric system
Postavljanje X-MULTI HOT START procedura: traje oko 3 minute od 0HZ do ciljanog broja HZ. Refrigerant system and electric system
--Frekvencijska kontrola kompresora: Kako sustav odabire radnu frekvenciju: Postavljanje X-MULTI Raspon frekvencija u ovisnosti o TAO Kontrola frekvencije kod pokretanja ureñaja Zahtjevi unutarnjih jedinica odreñuju početnu vrijednost frekvencije Tao<33 hlañenje Tao>5 grijanje Ciljana temperatura isparavanja ili kondenzacije Maksimalna snaga Granične frekvencije Kod promjene temperaturne razlike na un. jedinicama Sljedeći podaci koriste se za odabir radne frekvencije: --hlañenje: Tao, Tc2AVE, T=Tai-Toutlet Tao odreñuje frekvencijski raspon u kojem kompresor može raditi; Ako je TinAVE > ciljana vrijednost A, kompresor povećava frekvenciju; Ako je TinAVE < ciljana vrijednost A, kompresor smanjuje frekvenciju; T odreñuje početnu vrijednost frekvencije --grijanje: Tao, TmAVE, T=Toutlet-Tai Tao odreñuje frekvencijski raspon u kojem kompresor može raditi; Ako jetmave > ciljana vrijednost B, kompresor povećava frekvenciju; Ako jetmave < ciljana vrijednost B, kompresor smanjuje frekvenciju; T odreñuje početnu frekvenciju; Refrigerant system and electric system
Postavljanje X-MULTI --kontrola brzine rada ventilatora vanjske jedinice: Kako sustav odreñuje brzinu rada ventilatora vanjske jedinice : Kontrola rada ventilatora kod pokretanja ureñaja Brzinu ventilatora odreñuje Tao(vanjska temperatura) Brzinu ventilatora odreñuje vanjska jedinica hlañenje grijanje Brzinu rada ventilatora odreñuje TC Brzinu ventilatora odreñuje temp. razlika SH SH=Toci - Te HLAðENJE GRIJANJE Refrigerant system and electric system
--Kontrola defrosta vanjske jedinice: 1Ulazni uvjeti (sljedeća tri uvjeta moraju biti zadovoljena): -start up kompresora najmanje 10 minuta; -ukupno vrijeme rada kompresora je najmanje 45 minuta; -senzor Te vrijednost < ciljana vrijednost C (C=a-x, x=8 or 10, ovisno o postavkama) 2Defrost procedura: vidi sljedeću stranu --Kontrola grijača a kućišta ta: u svrhu zaštite kompresora 1Kada jetao A i kompresor ne radi, grijač je uključen (ON). 2) Kada je Tao A+5, ili kompresor radi, grijač je isključen (OFF). * A=27 Postavljanje X-MULTI Refrigerant system and electric system
Postavljanje X-MULTI Defrost procedura Refrigerant system and electric system
--PMV PMV s kontrole: Postavljanje X-MULTI 1U hlañenju, PMV-i rade prema stvarnom SH(=Tc1 Tc2) i ciljanoj SH vrijednosti. 2) U grijanju, PMV-i rade prema stvarnom SC(=Tm Tc2) i ciljanoj SC vrijednosti. Tc2 Isparivač - unutarnja jedinica Tc1 Tm Tai 3Kada je SH < ciljane vrijednosti SH, ventil se zatvara; Kada je SH > ciljane vrijednosti SH, ventil se otvara; 2) Kada je SC < ciljane vrijednosti SC, ventil se otvara; Kada je SC > ciljane vrijednosti SC, ventil se zatvara; SH Protok SC Refrigerant system and electric system 0 250 500 Pulse
5. Kratki uvod u instalaciju: Postavljanje X-MULTI --Instala Instalacijska procedura (za detaljnije upute vidi instalacijski priručnik): Odreñivanje mjesta instalacije Educiranje kupca o pravilnom načinu korištenja klima ureñaja. Polaganje instalacija i ožičenje Provjera rada ureñaja u hlañenju i grijanju Instalacija unutarnjih i vanjske jedinice Adresiranje unutarnjih jedinica Spajanje instalacija na pravi način Provjera napona: : 230V±10% Provjera cijele instalacije prije vakuumiranja Refrigerant system and electric system Vakuumiranje i eventualna nadopuna sustava
--Va Važne napomene kod instalacije: Postavljanje X-MULTI 1) za meñuvezu obavezno koristiti oklopljeni kabel; 2) instalater mora vakuumirati sustav kako bi se provjerilo eventualno curenje; 3) prije spajanja napojnih kablova i pokretanja ureñaja aja, potrebno je provjeriti je li napon u granicama 230V±10%; 4) sustav se uvijek dopunjava s R410A u tekućem em stanju; 5) prije pokretanja sustava potrebno se uvjeriti da su unutarnje jedinice pravilno adresirane Refrigerant system and electric system
Održavanje X-MULTI Moguće e pogreške i njihovo otklanjanje Trouble shooting
Održavanje X-MULTI --Problem Problemi i s temperaturnim senzorima zorima: : Te, Tao, Ts, Td, Tc, Toci,, Tc1, Tc2, Tm, Tai KAKO RIJEŠITI ITI PROBLEM SA SENZORIMA? Check the sensors according to the wiring diagram to see whether the sensor is properly inserted into the PCB no Re-insert it and check again yes Check the sensor whether it is broken or bad connection with the PCB no Check the resistance value to see whether it is normal no Bad sensor, change it and check again yes yes Change the sensor and check again Bad PCB, change it and check again Trouble shooting
Održavanje X-MULTI fault1.lcd has no display START check the LCD whether or not fit to the unit NO change the LCD then check again YES whether the LED red and LED green on the PCB of indoor unit is alternation flashing NO check whether the power terminal block has 220V input NO check the terminal block and power supply facility the PCB broken,change it NO check whether the LCD has 12V power supply check whether the power wire open circuit check whether the fuse burn the PCB broken,change it YES the LCD circuit broken,change it change the power wire then check again change the fuse then check again Trouble shooting
Održavanje X-MULTI fault2.the LCD display sensor fault start Brojčana oznaka pogreške refer to the circuit diagram,check whether the sensor instert right on the PCB no insert the sensor again 1 2 3 yes check whether the sensor open circuit or the PCB has broken faucet yes change the sensor,check again no check whether the sensor value correct yes the PCB broken,change it then check again no change sensor,check again 4 Trouble shooting
Održavanje X-MULTI fault3.the LCD display faulty of indoor unit start Kodovi kvara prikazani na ekranu unutarnje jedinice refer to the circuit diagram,check whether the communication terminal block wire is correct whether the communication wire between indoor and outdoor unit is open circuit reconnection the wire,check again whether the power wire and the communication wire too close up lead to communication data incorrect THE pcb broken,change it then check again 6 change the communication wire,check again make the wires proper space,check again Otklanjanje gresaka
Održavanje X-MULTI fault 4.indoor unit EEPROM data incorrect fault Kodovi kvara prikazani na ekranu unutarnje jedinice 1.the first time power on display this fault check the EEPROM pin or the eeprom broken 2. when the unit is running displsy this fault.the eeprom broken,change it 5 Trouble shooting
Održavanje X-MULTI fault5.indoor unit address repeated Kodovi kvara prikazani na ekranu unutarnje jedinice 1.do the address lookup firstly: Ł şturn off the indoorunit Ł press the buzzer continuous about 15 secł after the buzzer 5 times ring then loose.the LCD display the num is the address of this indoor unit,the address can be check by this way,if there is address repeated then follow this way to change the indoor unit address. 9 correspond to the address 1,the outdoor unit pipe B correspond to the address 2,the outdoor unit pipe C correspond to the address 3, Trouble shooting
Održavanje X-MULTI fault6.fan fault.ac has no 50HZ exceed zero verify Kodovi kvara prikazani na ekranu unutarnje jedinice start check thether the fan input block instert correct or open circuit ( PCB CN3) yes no CHECK whether the fan feedback wire instert correct or open circuit ( PCB CN23) yes no PCB broken,change it change the fan inpout block,turnoff the power,then turn on again and check change the fan feedback wire,turnoff the power,then turn on again an d check 11 Trouble shooting
Održavanje X-MULTI fault7.outdoor unit fault check the outdoor unit PCB (5 leds) display faulty code (binary system) Trouble shooting
Održavanje X-MULTI fault8.outdoor unit display sensor fault start Led 5.4.3.2.1 refer to the circuit diagram,check whether the sensor instert right on the PCB no insert the sensor again,check again yes check whether the sensor open circuit or the PCB has broken faucet check whether the sensor value correct change sensor,check again change the sensor,check again the PCB broken,change it then check again Trouble shooting
Održavanje X-MULTI fault 9.AC current exceed protect or current sensor broken.compressor jam rotate.compressor shake higher.compressor start abnormal.position check loop broken.compressor broken Led 5.4.3.2.1 the fanlt can be auto resume the first and twice.if the outdoor unit PCB display this fault all the time and can't clear,indicate that : 1.the SPDU broken,change it then refer to the circuit diagram connect the wire.(70ł ĄŁ 2.the POWER CIRCUIT BOARD short circuit make the SPDU broken. 3.comprosser broken make the SPDU display this fault Ł 10Ł ĄŁ 4.control circuit board data incorrect,change itł 5Ł ĄŁ Trouble shooting
Održavanje X-MULTI fault10.hp switch fault Led 5.4.3.2.1 reason 1.system pressure higher,unit stop to protection,so the fault can resume 2.the pressure switch wire insert incorrect or open circuit Trouble shooting
Održavanje X-MULTI start check whether the pressure switch wire and the faucet on the PCB is broken or open circuit (PCB CN20) no CHECK whether the two pin of the pressure is broken no whether the outdoor unit fan start normal when cooling no Ł change the control circuit board), check again yes yes change the pressure swicth wire,power off then power on and check again change the pressure swicth wire,power off then power on and check again check whether the outdoor unit fan has power input no change the outdoor fan motor,check again Trouble shooting
Održavanje X-MULTI fault 11.lp switch fault Led 5.4.3.2.1 reason 1.system pressure lower,unit stop to protection,so the fault can resume 2.the pressure switch wire insert incorrect or open circuit Trouble shooting
Održavanje X-MULTI start check whether the pressure switch wire and the faucet on the PCB is broken or open circuit (PCB CN19) no CHECK whether the two pin of the pressure is broken no whether the outdoor unit fan start normal when cooling no Ł change the control circuit board), check again yes yes yes change the pressure swicth wire,power off then power on and check again change the pressure swicth wire,power off then power on and check again check whether the outdoor unit fan has power input no change the outdoor fan motor,check again Trouble shooting
Hvala!