Low Surface Temperature Radiators Safe & Hygienic Heating Solutions

Ci/SfB April 2011 56.9 X The LST Specialists Low Surface Temperature Radiators Safe & Hygienic Heating Solutions

Contents Page 1 Page 2 Page 4 Page 6 Page 8 Page 9 Page 10 Page 12 Page 20 Page 28 Page 32 Page 34 Page 35 Page 36 Introduction The DeepClean Way Anti-Ligature Technology Healthcare Acquired Infections BioCote Anti-Microbial Protection Our Service The LST Selection Guide Trionic DeepClean Anti-Ligature Trionic DeepClean LST Trionic Classic LST Bespoke Designs Specification Trionic LST Technical Other Products The LST Specialists Turn page

Designing the ultimate LST Radiator Radius corners will make it safer if someone falls against one. Offer Anti-Ligature Grilles for Mental Health applications. Offer a wide range of security locks for high risk areas. Powder coated inside & outside for full Biocote protection. Narrow grilles to stop little fingers getting inside & pens and stuff lost inside. 2 thick casings available for high security or mental health applications. Use Zintec protected mild steel - gives additional corrosion resistance Made from 1.5 Zintec mild steel - 1.2 models can be quite flimsy. Casings supplied in one piece - no site assembly required. Casing available in aluminium for wet areas. Patented stepped design allows door to lie flat on floor when open.

Herz high-quality European valves supplied as standard. Offer - optional safety chain to keep door secure when opening. Optional cut-outs available All ends folded for increased strength & rigidity Anti-Ligature shroud makes the TRV safer. Quality German made Kermi Radiator tested to EN 442 with 5 yrs warranty Internal fixings for neater appearance & better security, Add floor fixings too, you wont knock this off the wall easily! Rotary Valve fittings enable radiator to be lowered for cleaning of wall & rear of radiator. Radius grille punch-outs to make it easier to clean - square patterns trap the dirt in the corners.

Introduction Page 1 Hospitals, clinics, care homes and schools are all environments where vulnerable users require protection from dangerously hot surfaces. It is therefore critical to service providers that surface temperatures are low and products are clean, simple, easily controlled and require little maintenance. Poor design which neglects any of these essential areas Hospitals can compromise safety and have significant consequences for both end users and service providers. GP Surgeries With the pressure to provide buildings fit for purpose constantly increasing, intense media coverage surrounding MRSA and other healthcare acquired infections only adds to the demands placed upon Schools & Nurseries service providers. Guided by these key drivers, the design team at Contour Casings, in consultation with industry experts, has developed a new range of low surface temperature radiator products that address all of today s essential requirements. Nursing Homes Day Centres Secure Units Mental Health Facilities

Page 2 The DeepClean Way The Problem The problem of accessing inside of LST radiators for cleaning and maintenance has been an issue for service providers for many years. The Association of Healthcare Cleaning Professionals (AHCP) recoends that minimum cleaning frequencies for radiators are: Very High Risk Areas - Daily High Risk Areas Daily Significant Risk Areas - Daily Low Risk Areas Monthly Budgets cuts and understaffing make it difficult to maintain recoended cleaning schedules, with internal cleaning rarely taking place. This creates a greater risk to both end users and providers, with potentially higher infection rates. Low surface temperature (LST) radiators harbour dirt. The convection heating process draws in particles, lint and other contaminants and then re-distributes these particles in the air. An undisturbed casing provides ideal conditions for the growth and distribution of dirt, spores and bacteria, greatly increasing the risk of infection. Therefore, environments such as hospitals, care homes and schools, require a product that allows for fast and effective cleaning. MRSA can survive in a desiccated state in dust for long periods up to 175 days. (Source: Long-term-in-vitro survival of an epidemic MRSA phage-group III-29 strain J.H.T Wagenvoort and R.J.R Penders). Traditional LST radiator casing designs are fixed boxes and are difficult to access, with internal cleaning involving complete disassembly. Many current radiator guards are heavy and awkward to lift, cleaning staff require the assistance of several maintenance personnel and the whole process of cleaning a radiator casing is slow and costly. One guard alone can take up to 30 minutes to disassemble, remove, clean, reassemble and refit. The Solution The Trionic DeepClean LST Radiator from Contour Casings is made from a robust one-piece construction, dramatically reducing installation time and making it possible for a cleaning operative to clean the product internally and on their own. A patented, quick release, full access hinged door (UK Patent No: 2 410 544), allows the front of the casing to lie flat on the floor. The door can then be stood upon if necessary while cleaning, without resulting in any structural damage. The open-hinge design also facilitates complete door removal if required. By incorporating unique rotary valve fittings, this design also allows the radiator to be lowered down to floor level. Cleaning is now possible on the top, front, sides and back of the radiator, as well as the wall around and behind the radiator. The Biocote silver-based anti-microbial coating reduces the risk of bacteria growing on the casing in an additional step towards preventing the spread of hospital acquired infections. W: www.contourcasings.co.uk E: sales@contourcasings.co.uk T: 01952 290 498 F: 01952 210 261

The DeepClean LST pays for itself Page 3 An example costing estimates that a property containing 800 radiators would require: Traditional DeepClean 2 person job involving estates personnel 1 cleaning operative can now open the LST casing 30 minutes to remove 1 LST casing, clean casing internally, clean radiator, clean wall, clean floor and refit casing (wall & back of radiator cannot be cleaned) 5 minutes to clean every internal surface of the casing and the radiator, including back of radiator and whole wall space x 14 7 hour working day = 14 LST radiators cleaned per day per team x 84 In an average day of 7 working hours, 1 person can clean 84 radiators 57 days for 2 people to clean every radiator in the property 9.5 days for 1 person to clean every radiator in the property Daily cleaning of radiators would require a team of 114 dedicated staff x 114 x 10 Daily cleaning would now require only 10 dedicated cleaners, with little or no support from the estates department An annual budget of 1.727 million at minimum wage ( 5.93 ph) to clean all of its radiators on a daily basis At minimum wage ( 5.93 ph) this would cost the property 151,511 per year Saving 1.575 Million per year or 1,968 per radiator But more importantly, cleaning standards would be significantly improved and the risk of cross contamination dramatically reduced, thereby assisting in the reduction of HAI s. Consequently, this would provide greater savings and improved efficiencies within the property, as lower rates of HAI s free-up beds.

Page 4 Anti-Ligature Technology As a key part of the low surface temperature offer, Contour Casings has developed a specialist range of LST radiators for use in secure environments such as mental health facilities and prisons, where reducing the risk of potential ligature points is of paramount importance. According to the 2005 mortality statistics, 54% of all 3172 suicides in England & Wales were by hanging, and there are as many as ten times more attempted suicides every year. As death from hanging can often occur when an individual is not fully suspended, the inspection of psychiatric wards and cells for potential ligature points should focus on fixtures and fittings at all heights. Grilles and external TRV s in LST radiators pose particular danger. Ligature points on Contour Casings antiligature LST radiator ranges have therefore been identified and addressed. Secure anti-ligature mesh is fitted behind all grilles, decreasing the risk of the main grille being used as a ligature point An anti-ligature TRV shroud has been developed to make it far more difficult to attach ligatures A wide range of security fixings and fasteners are available to stop unauthorised personnel gaining access to inside the casing Internal fixings are used to prevent unauthorised removal or tampering of the casing A separate range of products for other antiligature applications, such as ceiling grilles, has also been developed. Anti-ligature TRV Shroud Security Fastenings Security Fastenings Options W: www.contourcasings.co.uk E: sales@contourcasings.co.uk T: 01952 290 498 F: 01952 210 261

Anti-ligature Grille and Mesh Anti-ligature Ceiling Grille Anti-Ligature Base Plate Page 5

Page 6 Healthcare Acquired Infections The Problem With the recent rise in the awareness of so called Superbugs such as MRSA and E.coli, the issue of Healthcare Acquired Infection (HAI) has never been higher in the public and political consciousness. The threat of bacteria cross-contamination and contracting an infection is particularly high in healthcare environments, where there is an abundance of bacteria and a large number of people with low iunity levels confined to a small space. Obvious ways of passing on infection are via proximity or direct contact with contaminated surfaces. At any one time 1 in 8 patients have an HAI. Patients contracting a HAI spend an average of 2.9 times longer in hospital and at an estimated cost to the NHS of over 1 Billion each year. There are over 300,000 HAI s each year in England, with over 9000 deaths attributed to MRSA and other Superbugs in 2007. Hospital Trust expenditure on cleaning wards in 2004 exceeded 522 Million. (Source: House of Coons Public Accounts Coittee Reducing Healthcare Associated Infection in Hospitals in England November 2009) Research into the economic impact of HAI s concluded that the cost of introducing preventative measures is less than treating infections. Around 15-30% could be prevented by better application of best practice, releasing resources of 150-300 Million for alternative NHS use. W: www.contourcasings.co.uk E: sales@contourcasings.co.uk T: 01952 290 498 F: 01952 210 261

Biocote Anti-Microbial Protection Page 7 The Solution Contour Casings incorporates BioCote anti-microbial protection into LST radiators. This patented anti-microbial powder coating, provides an effective, safe and long lasting solution to a wide range of potentially dangerous bacteria, including MRSA and E.coli. The anti-microbial efficacy of BioCote products has been independently tested against a wide range of Gram- positive and Gram-negative bacteria, as well as fungi. BioCote has repeatedly demonstrated reduction in the growth of these organisms and therefore becoming an integral component of good hygiene practice. BioCote is: Effective - The silver ions in BioCote cause critical functions in the bacteria to break down. The bacteria become unable to reproduce and die. Independent tests show BioCote reduces MRSA, Listeria, E.coli and Salmonella by up to 99%. Safe - The active ingredient in BioCote is the element silver, this is present in the form of silver ions. Silver is a natural antimicrobial and has been used in this way for centuries. Unlike antibiotics, there is no evidence of bacteria becoming resistant to BioCote. Long Lasting - BioCote does not leach out. The life of the products treated with BioCote has been simulated and showed no significant reduction in performance. Proven Protection Regular quality control testing is carried out to ensure the continual effectiveness of BioCote - copies of the reports are available. BioCote is independently tested to be effective against a wide range bacteria, including: Staphylococcus aureus (including MRSA) Escherichia coli (E.coli) Listeria monocytogenes Streptococcus faecalis Salmonella enteritidis Life Time Protection Products treated with BioCote show no significant reduction in the anti-microbial efficacy for the entire life of the product or material. % Living Bacteria 100 90 80 70 60 50 40 30 20 10 0 0 15min 30min 45min 1hr Time MRSA E.coli The graph above shows how, on a BioCote protected product, levels of bacteria are reduced by up to 99% over a two hour period. 2hrs LST radiator manufacture is regularly and independently tested to ensure correct application of BioCote. For more information on BioCote, visit the website at www.biocote.com

Page 8 Our Services - The Contour Difference Contour Casings does not only believe in supplying high-quality products and innovative design solutions. Contour Casings also provide a unique range of services and products, setting the company apart from competitors and reinforcing its position as market leader. With lead times of up to half that of other LST radiator suppliers, split deliveries as standard and exclusive patented products and features, Contour Casings can satisfy all of your design, survey and installation requirements to the highest possible standards, from concept through to installation. Technical Support & Bespoke Options Contour Casings can provide a bespoke design service for projects with unique requirements (see page 32). A team of technical experts and design specialists are available to discuss any of your development ideas and answer your questions, ensuring a product matching your exact criteria is produced. Tel: 01952 290 498 Email: technical@contourcasings.co.uk At Contour Casings, design and functionality are never compromised; instead, preferences are individually tailored to that which is affordable. For building schemes where budgets are constrained, Contour Casings has vast experience at value engineering, particularly where cost considerations are a priority. Full technical details, including outputs and sizing, are available on the Hevacomp system. Site Surveys Free site surveys are available from Contour Casings, ensuring products and manufacturing are accurate. Expert surveyors will identify the correct size of product needed, taking note of any cutouts or special requirements that are necessary. Modifications can then be prograed into manufacture, making the installation process more efficient. Contour Casings team of surveyors can work with you to suggest innovative and alternative design modifications on your original concepts, helping you reduce installation time and costs. Split Deliveries To reduce the constant risk of casings becoming damaged or lost on site, Contour Casings offer split deliveries as standard on all LST radiators. Radiators and valves are delivered first, then, once the heating system is installed, tested and coissioned; casings are delivered, virtually eliminating storage problems and the risk of site damage. Radiator Guard Installation Contour Casings offer a full supply & fit service for radiator casings. Expert installation and project management teams can handle the entire project for you through to completion, with the minimum of disruption to all building occupants. All installers are experienced, skilled operatives, each with extensive knowledge and training on installing Contours products. All hold CSCS cards and are CRB checked. Whether it is a refurbishment or a new build project, a single radiator cover or a whole hospital, wherever in the country you are Contour Casings can help. CONTRACTORS HEALTH & SAFETY ASSESSMENT SCHEME Accredited Contractor www.chas.gov.uk W: www.contourcasings.co.uk E: sales@contourcasings.co.uk T: 01952 290 498 F: 01952 210 261

Page 9

Page 10 The LST Selection Guide W: www.contourcasings.co.uk E: sales@contourcasings.co.uk T: 01952 290 498 F: 01952 210 261

Page 11 To assist with product selection we have produced a general guide based upon typical needs by application. We would recoend a thorough risk assessment of service user needs before final selection, The table provides a quick and easy way of finding the LST that is most suited to yours and your clients needs. Trionic DeepClean LST, Anti-Ligature, Floor Mounted, Square Top Trionic DeepClean LST, Anti-Ligature, Wall Mounted, Square Top Trionic DeepClean LST, Anti-Ligature, Floor Mounted, Gradient Top Trionic DeepClean LST, Anti-Ligature, Wall Mounted, Gradient Top Trionic DeepClean LST, Floor Mounted, Square Top Trionic DeepClean LST, Wall Mounted, Square Top Trionic DeepClean LST, Floor Mounted, Gradient Top Trionic DeepClean LST, Wall Mounted, Gradient Top Trionic Classic LST, Floor Mounted, Square Top Trionic Classic LST, Wall Mounted, Square Top Hospital Doctor Surgery Health Centre Psychiatric Unit Elderly Peoples Home Sheltered Housing S E N School School/Nursery Youth Centre Childrens Home Prison/Secure Unit Rehab Clinic Sport Centre Rehabilitation Unit Library Page 12 14 16 18 20 22 24 26 28 30 Contour Casings recoended LST for these environments Could possibly be used in these environments Not advisable to use in these environments Note: If the project that you are working on is not shown in the above table, please contact our technical department on Tel: 01952 290498 or email us at sales@contourcasings.co.uk for further assistance.

Page 12 Trionic Anti-Ligature DeepClean LST This anti-ligature LST radiator, for use in secure units and mental health facilities, has a floor mounted design which enhances structural integrity. This radiator also incorporates several specific design features: Unrivalled access for internal cleaning or routine maintenance. Patented front door (UK Patent No: 2 410 544) lies flat on floor, enabling quick access without complete door removal. Open hinge arrangement allows simple removal of door if required. A secondary expanded metal mesh (to IP31 specification) is welded behind all grilles to prevent items 3.0 in diameter or greater being inserted. Conical anti-ligature TRV shroud with viewing window enables building users to control radiator temperature easily, whilst reducing the ligature risk of an exposed TRV. Casing Depths Type 11 155 Type 12 165 Type 22 195 Outputs Outputs based upon a mean radiator water temperature of 70 C and a room temperature of 20 C Delta T 50 C. See Page 35. External Valve Location A 28 diameter cut-out for the external valve / TRV Shroud is located 80 from the top of the righthand side of the casing. If an alternative position or size is required, please advise at time of order. Standard Delivery Standard delivery comprises of Trionic LST Cover of choice, corresponding Kermi emitter (Type 11, Type 12 or Type 22 as specified) and the option of an anti-ligature TRV shroud and 9231-63 Herz External TRV kit (suitable for 15 copper to copper connection on a two pipe system) or a 9210-13 Herz internal TRV kit. An optional rotary valve is available. Alternative Herz fittings can be quoted for and supplied upon request. Covers and shrouds can be supplied on a separate delivery, helping to avoid on site damage. Rad Length Casing Length 400 600 500 700 600 800 700 900 800 1000 900 1100 1000 1200 1100 1300 1200 1400 1400 1600 1600 1800 1800 2000 Rad Height Casing Height Type 11 400 500 600 650 750 850 DSF116506-AL DSF117506-AL DSF118506-AL Watts T50 223 269 314 DSF116507-AL DSF117507-AL DSF118507-AL Watts T50 279 336 392 DSF116508-AL DSF117508-AL DSF118508-AL Watts T50 334 403 470 DSF116509-AL DSF117509-AL DSF118509-AL Watts T50 390 470 548 DSF116510-AL DSF117510-AL DSF118510-AL Watts T50 446 538 626 DSF116511-AL DSF117511-AL DSF118511-AL Watts T50 502 605 705 DSF116512-AL DSF117512-AL DSF118512-AL Watts T50 558 672 783 DSF116513-AL DSF117513-AL DSF118513-AL Watts T50 614 739 862 DSF116514-AL DSF117514-AL DSF118514-AL Watts T50 669 806 940 DSF116516-AL DSF117516-AL DSF118516-AL Watts T50 781 941 1,097 DSF116518-AL DSF117518-AL DSF118518-AL Watts T50 892 1,075 1,254 DSF116520-AL DSF117520-AL DSF118520-AL Watts T50 1,004 1,210 1,410 W: www.contourcasings.co.uk E: sales@contourcasings.co.uk T: 01952 290 498 F: 01952 210 261

Page 13 > Floor Mounted > Square Top Depth > Types 11, 12 & 22 > Anti-Ligature Height Length Type 12 Type 22 750 500 600 750 400 500 600 750 1000 750 850 1000 650 750 850 1000 DSF111006-AL DSF127506-AL DSF128506-AL DSF121006-AL DSF227506-AL DSF228506-AL DSF221006-AL 379 340 394 472 461 533 636 DSF111007-AL DSF127507-AL DSF128507-AL DSF121007-AL DSF227507-AL DSF228507-AL DSF221007-AL 474 426 492 590 577 666 795 DSF111008-AL DSF127508-AL DSF128508-AL DSF121008-AL DSF226508-AL DSF227508-AL DSF228508-AL DSF221008-AL 569 510 590 708 579 692 800 954 DSF111009-AL DSF127509-AL DSF128509-AL DSF121009-AL DSF226509-AL DSF227509-AL DSF228509-AL DSF221009-AL 664 595 688 826 676 807 933 1,113 DSF111010-AL DSF127510-AL DSF128510-AL DSF121010-AL DSF226510-AL DSF227510-AL DSF228510-AL DSF221010-AL 758 680 786 944 773 922 1,066 1,272 DSF111011-AL DSF127511-AL DSF128511-AL DSF121011-AL DSF226511-AL DSF227511-AL DSF228511-AL DSF221011-AL 854 766 885 1,062 869 1,038 1,200 1,430 DSF111012-AL DSF127512-AL DSF128512-AL DSF121012-AL DSF226512-AL DSF227512-AL DSF228512-AL DSF221012-AL 948 850 983 1,180 966 1,153 1,333 1,590 DSF111013-AL DSF127513-AL DSF128513-AL DSF121013-AL DSF226513-AL DSF227513-AL DSF228513-AL DSF221013-AL 1,043 935 1,082 1,298 1,062 1,268 1,466 1,749 DSF111014-AL DSF127514-AL DSF128514-AL DSF121014-AL DSF226514-AL DSF227514-AL DSF228514-AL DSF221014-AL 1,138 1,021 1,180 1,416 1,159 1,383 1,599 1,908 DSF111016-AL DSF127516-AL DSF128516-AL DSF121016-AL DSF226516-AL DSF227516-AL DSF228516-AL 1,327 1,190 1,377 1,652 1,352 1,614 1,866 DSF127518-AL DSF128518-AL DSF226518-AL DSF227518-AL DSF228518-AL 1,361 1,574 1,545 1,845 2,133 DSF127520-AL DSF128520-AL DSF226520-AL DSF227520-AL DSF228520-AL 1,531 1,770 1,738 2,075 2,399

Page 14 Trionic Anti-Ligature DeepClean LST The anti-ligature LST wall mounted radiator has been developed for use in secure units and mental health facilities, it incorporates several specific design features: Unrivalled access for internal cleaning or routine maintenance. Patented front door (UK Patent No: 2 410 544) lies flat on floor, enabling quick access without complete door removal. Open hinge arrangement allows simple removal of door if required. A secondary expanded metal mesh (to IP31 specification) is spot welded behind all grilles to prevent items 3.0 in diameter or greater being inserted. Conical anti-ligature TRV shroud with viewing window enables building users to control radiator temperature easily, whilst reducing the ligature risk of an exposed TRV. Anti-ligature base plate to secure the underside of the guard. Casing Depths Type 11 155 Type 12 165 Type 22 195 Outputs Outputs based upon a mean radiator water temperature of 70 C and a room temperature of 20 C Delta T 50 C. See Page 35. External Valve Location A 28 diameter cut-out for the external valve / TRV Shroud is located 80 from the top of the righthand side of the casing. If an alternative position or size is required, please advise at time of order. Standard Delivery Standard delivery comprises of Trionic LST Cover of choice, corresponding Kermi emitter (Type 11, Type 12 or Type 22 as specified) and the option of an anti-ligature TRV shroud and 9231-63 Herz External TRV kit (suitable for 15 copper to copper connection on a two pipe system) or a 9210-13 Herz internal TRV kit. An optional rotary valve is available. Alternative Herz fittings can be quoted for and supplied upon request. Covers and shrouds can be supplied on a separate delivery, helping to avoid on site damage. Rad Length Casing Length 400 600 500 700 600 800 700 900 800 1000 900 1100 1000 1200 1100 1300 1200 1400 1400 1600 1600 1800 1800 2000 Rad Height Casing Height Type 11 400 500 600 550 650 750 DSW115506-AL DSW116506-AL DSW117506-AL Watts T50 229 276 321 DSW115507-AL DSW116507-AL DSW117507-AL Watts T50 286 344 402 DSW115508-AL DSW116508-AL DSW117508-AL Watts T50 343 413 481 DSW115509-AL DSW116509-AL DSW117509-AL Watts T50 400 482 562 DSW115510-AL DSW116510-AL DSW117510-AL Watts T50 458 551 642 DSW115511-AL DSW116511-AL DSW117511-AL Watts T50 514 620 722 DSW115512-AL DSW116512-AL DSW117512-AL Watts T50 572 689 803 DSW115513-AL DSW116513-AL DSW117513-AL Watts T50 629 758 883 DSW115514-AL DSW116514-AL DSW117514-AL Watts T50 686 827 964 DSW115516-AL DSW116516-AL DSW117516-AL Watts T50 800 964 1,124 DSW115518-AL DSW116518-AL DSW117518-AL Watts T50 914 1,102 1,285 DSW115520-AL DSW116520-AL DSW117520-AL Watts T50 1,029 1,240 1,445 W: www.contourcasings.co.uk E: sales@contourcasings.co.uk T: 01952 290 498 F: 01952 210 261

Page 15 > Wall Mounted > Square Top Depth > Types 11, 12 & 22 > Anti-Ligature Height Length Type 12 Type 22 750 500 600 750 400 500 600 750 900 650 750 900 550 650 750 900 DSW119006-AL DSW126506-AL DSW127506-AL DSW129006-AL DSW226506-AL DSW227506-AL DSW229006-AL 389 349 403 484 472 546 652 DSW119007-AL DSW126507-AL DSW127507-AL DSW129007-AL DSW226507-AL DSW227507-AL DSW229007-AL 486 436 504 605 591 683 815 DSW119008-AL DSW126508-AL DSW127508-AL DSW129008-AL DSW225508-AL DSW226508-AL DSW227508-AL DSW229008-AL 583 523 604 726 594 709 820 977 DSW119009-AL DSW126509-AL DSW127509-AL DSW129009-AL DSW225509-AL DSW226509-AL DSW227509-AL DSW229009-AL 681 610 705 847 693 827 956 1,141 DSW119010-AL DSW126510-AL DSW127510-AL DSW129010-AL DSW225510-AL DSW226510-AL DSW227510-AL DSW229010-AL 777 697 806 968 792 945 1,093 1,304 DSW119011-AL DSW126511-AL DSW127511-AL DSW129011-AL DSW225511-AL DSW226511-AL DSW227511-AL DSW229011-AL 875 785 907 1,089 891 1,064 1,230 1,466 DSW119012-AL DSW126512-AL DSW127512-AL DSW129012-AL DSW225512-AL DSW226512-AL DSW227512-AL DSW229012-AL 972 872 1,008 1,210 990 1,182 1,366 1,629 DSW119013-AL DSW126513-AL DSW127513-AL DSW129013-AL DSW225513-AL DSW226513-AL DSW227513-AL DSW229013-AL 1,069 959 1,109 1,331 1,089 1,300 1,503 1,793 DSW119014-AL DSW126514-AL DSW127514-AL DSW129014-AL DSW225514-AL DSW226514-AL DSW227514-AL DSW229014-AL 1,166 1,046 1,210 1,451 1,188 1,418 1,639 1,956 DSW119016-AL DSW126516-AL DSW127516-AL DSW129016-AL DSW225516-AL DSW226516-AL DSW227516-AL 1,360 1,220 1,411 1,693 1,386 1,655 1,913 DSW126518-AL DSW127518-AL DSW225518-AL DSW226518-AL DSW227518-AL 1,395 1,613 1,583 1,891 2,186 DSW126520-AL DSW127520-AL DSW225520-AL DSW226520-AL DSW227520-AL 1,569 1,814 1,782 2,127 2,459

Page 16 Trionic Anti-Ligature DeepClean LST This anti-ligature LST radiator, for use in secure units and mental health facilities, has a floor mounted design which enhances structural integrity. The gradient top prevents the casing being used as a rest surface. This radiator also incorporates several specific design features: Unrivalled access for internal cleaning or routine maintenance. Patented front door (UK Patent No: 2 410 544) lies flat on floor, enabling quick access without complete door removal. Open hinge arrangement allows simple removal of door if required. A secondary expanded metal mesh (to IP31 specification) is welded behind all grilles to prevent items 3.0 in diameter or greater being inserted. Conical anti-ligature TRV shroud with viewing window enables building users to control radiator temperature easily, whilst reducing the ligature risk of an exposed TRV. Casing Depths Type 11 155 Type 12 165 Type 22 195 Outputs Outputs based upon a mean radiator water temperature of 70 C and a room temperature of 20 C Delta T 50 C. See Page 35. External Valve Location A 28 diameter cut-out for the external valve / TRV Shroud is located 80 from the top of the righthand side of the casing. If an alternative position or size is required, please advise at time of order. Standard Delivery Standard delivery comprises of Trionic LST Cover of choice, corresponding Kermi emitter (Type 11, Type 12 or Type 22 as specified) and the option of an anti-ligature TRV shroud and 9231-63 Herz External TRV kit (suitable for 15 copper to copper connection on a two pipe system) or a 9210-13 Herz internal TRV kit. An optional rotary valve is available. Alternative Herz fittings can be quoted for and supplied upon request. Covers and shrouds can be supplied on a separate delivery, helping to avoid on site damage. Rad Length Casing Length 400 600 500 700 600 800 700 900 800 1000 900 1100 1000 1200 1100 1300 1200 1400 1400 1600 1600 1800 1800 2000 Rad Height Casing Height Type 11 400 500 600 680 780 880 DGF116806-AL DGF117806-AL DGF118806-AL Watts T50 229 276 321 DGF116807-AL DGF117807-AL DGF118807-AL Watts T50 286 344 402 DGF116808-AL DGF117808-AL DGF118808-AL Watts T50 343 413 481 DGF116809-AL DGF117809-AL DGF118809-AL Watts T50 400 482 562 DGF116810-AL DGF117810-AL DGF118810-AL Watts T50 458 551 642 DGF116811-AL DGF117811-AL DGF118811-AL Watts T50 514 620 722 DGF116812-AL DGF117812-AL DGF118812-AL Watts T50 572 689 803 DGF116813-AL DGF117813-AL DGF118813-AL Watts T50 629 758 883 DGF116814-AL DGF117814-AL DGF118814-AL Watts T50 686 827 964 DGF116816-AL DGF117816-AL DGF118816-AL Watts T50 800 964 1,124 DGF116818-AL DGF117818-AL DGF118818-AL Watts T50 914 1,102 1,285 DGF116820-AL DGF117820-AL DGF118820-AL Watts T50 1,029 1,240 1,445 W: www.contourcasings.co.uk E: sales@contourcasings.co.uk T: 01952 290 498 F: 01952 210 261

Page 17 > Floor Mounted > Gradient Top Depth > Types 11, 12 & 22 > Anti-Ligature Height Length Type 12 Type 22 750 500 600 750 400 500 600 750 1030 785 885 1035 695 795 895 1045 DGF111006-AL DGF127806-AL DGF128806-AL DGF121006-AL DGF227906-AL DGF228906-AL DGF221006-AL 389 349 403 484 472 546 652 DGF111007-AL DGF127807-AL DGF128807-AL DGF121007-AL DGF227907-AL DGF228907-AL DGF221007-AL 486 436 504 605 591 683 815 DGF111008-AL DGF127808-AL DGF128808-AL DGF121008-AL DGF226908-AL DGF227908-AL DGF228908-AL DGF221008-AL 583 523 604 726 594 709 820 977 DGF111009-AL DGF127809-AL DGF128809-AL DGF121009-AL DGF226909-AL DGF227909-AL DGF228909-AL DGF221009-AL 681 610 705 847 693 827 956 1,141 DGF111010-AL DGF127810-AL DGF128810-AL DGF121010-AL DGF226910-AL DGF227910-AL DGF228910-AL DGF221010-AL 777 697 806 968 792 945 1,093 1,304 DGF111011-AL DGF127811-AL DGF128811-AL DGF121011-AL DGF226911-AL DGF227911-AL DGF228911-AL DGF221011-AL 875 785 907 1,089 891 1,064 1,230 1,466 DGF111012-AL DGF127812-AL DGF128812-AL DGF121012-AL DGF226912-AL DGF227912-AL DGF228912-AL DGF221012-AL 972 872 1,008 1,210 990 1,182 1,366 1,629 DGF111013-AL DGF127813-AL DGF128813-AL DGF121013-AL DGF226913-AL DGF227913-AL DGF228913-AL DGF221013-AL 1,069 959 1,109 1,331 1,089 1,300 1,503 1,793 DGF111014-AL DGF127814-AL DGF128814-AL DGF121014-AL DGF226914-AL DGF227914-AL DGF228914-AL DGF221014-AL 1,166 1,046 1,210 1,451 1,188 1,418 1,639 1,956 DGF111016-AL DGF127816-AL DGF128816-AL DGF121016-AL DGF226916-AL DGF227916-AL DGF228916-AL 1,360 1,220 1,411 1,693 1,386 1,655 1,913 DGF127818-AL DGF128818-AL DGF226918-AL DGF227918-AL DGF228918-AL 1,395 1,613 1,583 1,891 2,186 DGF127820-AL DGF128820-AL DGF226920-AL DGF227920-AL DGF228920-AL 1,569 1,814 1,782 2,127 2,459

Page 18 Trionic Anti-Ligature DeepClean LST This anti-ligature LST radiator has been developed for use in secure units and mental health facilities. The gradient top prevents the casing being used as a rest surface. This radiator also incorporates several specific design features: Unrivalled access for internal cleaning or routine maintenance. Patented front door (UK Patent No: 2 410 544) lies flat on floor, enabling quick access without complete door removal. Open hinge arrangement allows simple removal of door if required. A secondary expanded metal mesh (to IP31 specification) is welded behind all grilles to prevent items 3.0 in diameter or greater being inserted. Conical anti-ligature TRV shroud with viewing window enables building users to control radiator temperature easily, whilst reducing the ligature risk of an exposed TRV. Anti-ligature base plate to secure the underside of the guard. Casing Depths Type 11 155 Type 12 165 Type 22 195 Outputs Outputs based upon a mean radiator water temperature of 70 C and a room temperature of 20 C Delta T 50 C. See Page 35. External Valve Location A 28 diameter cut-out for the external valve / TRV Shroud is located 80 from the top of the righthand side of the casing. If an alternative position or size is required, please advise at time of order. Standard Delivery Standard delivery comprises of Trionic LST Cover of choice, corresponding Kermi emitter (Type 11, Type 12 or Type 22 as specified) and the option of an anti-ligature TRV shroud and 9231-63 Herz External TRV kit (suitable for 15 copper to copper connection on a two pipe system) or a 9210-13 Herz internal TRV kit. An optional rotary valve is available. Alternative Herz fittings can be quoted for and supplied upon request. Covers and shrouds can be supplied on a separate delivery, helping to avoid on site damage. Rad Length Casing Length 400 600 500 700 600 800 700 900 800 1000 900 1100 1000 1200 1100 1300 1200 1400 1400 1600 1600 1800 1800 2000 Rad Height Casing Height Type 11 400 500 600 580 680 780 DGW115806-AL DGW116806-AL DGW117806-AL Watts T50 234 282 329 DGW115807-AL DGW116807-AL DGW117807-AL Watts T50 293 353 412 DGW115808-AL DGW116808-AL DGW117808-AL Watts T50 351 423 493 DGW115809-AL DGW116809-AL DGW117809-AL Watts T50 410 494 575 DGW115810-AL DGW116810-AL DGW117810-AL Watts T50 469 564 658 DGW115811-AL DGW116811-AL DGW117811-AL Watts T50 527 635 740 DGW115812-AL DGW116812-AL DGW117812-AL Watts T50 585 706 822 DGW115813-AL DGW116813-AL DGW117813-AL Watts T50 644 776 905 DGW115814-AL DGW116814-AL DGW117814-AL Watts T50 702 847 987 DGW115816-AL DGW116816-AL DGW117816-AL Watts T50 820 988 1,152 DGW115818-AL DGW116818-AL DGW117818-AL Watts T50 937 1,129 1,316 DGW115820-AL DGW116820-AL DGW117820-AL Watts T50 1,054 1,270 1,480 W: www.contourcasings.co.uk E: sales@contourcasings.co.uk T: 01952 290 498 F: 01952 210 261

Page 19 > Wall Mounted > Gradient Top Depth > Types 11, 12 & 22 > Anti-Ligature Height Length Type 12 Type 22 750 500 600 750 400 500 600 750 930 685 785 935 595 695 795 945 DGW111006-AL DGW126806-AL DGW127806-AL DGW129306-AL DGW226906-AL DGW227906-AL DGW229406-AL 398 357 413 496 484 559 668 DGW111007-AL DGW126807-AL DGW127807-AL DGW129307-AL DGW226907-AL DGW227907-AL DGW229407-AL 498 447 517 620 606 700 835 DGW111008-AL DGW126808-AL DGW127808-AL DGW129308-AL DGW225908-AL DGW226908-AL DGW227908-AL DGW229408-AL 597 536 619 743 608 727 840 1,001 DGW111009-AL DGW126809-AL DGW127809-AL DGW129309-AL DGW225909-AL DGW226909-AL DGW227909-AL DGW229409-AL 697 625 722 868 710 848 979 1,168 DGW111010-AL DGW126810-AL DGW127810-AL DGW129310-AL DGW225910-AL DGW226910-AL DGW227910-AL DGW229410-AL 796 714 826 991 811 969 1,120 1,336 DGW111011-AL DGW126811-AL DGW127811-AL DGW129311-AL DGW225911-AL DGW226911-AL DGW227911-AL DGW229411-AL 896 804 929 1,116 912 1,089 1,260 1,502 DGW111012-AL DGW126812-AL DGW127812-AL DGW129312-AL DGW225912-AL DGW226912-AL DGW227912-AL DGW229412-AL 995 893 1,032 1,239 1,014 1,210 1,399 1,669 DGW111013-AL DGW126813-AL DGW127813-AL DGW129313-AL DGW225913-AL DGW226913-AL DGW227913-AL DGW229413-AL 1,095 982 1,136 1,363 1,116 1,331 1,540 1,836 DGW111014-AL DGW126814-AL DGW127814-AL DGW129314-AL DGW225914-AL DGW226914-AL DGW227914-AL DGW229414-AL 1,194 1,072 1,239 1,487 1,217 1,452 1,679 2,003 DGW111016-AL DGW126816-AL DGW127816-AL DGW129316-AL DGW225916-AL DGW226916-AL DGW227916-AL 1,394 1,250 1,446 1,735 1,420 1,695 1,960 DGW126818-AL DGW127818-AL DGW225918-AL DGW226918-AL DGW227918-AL 1,429 1,652 1,622 1,937 2,239 DGW126820-AL DGW127820-AL DGW225920-AL DGW226920-AL DGW227920-AL 1,608 1,858 1,825 2,179 2,519

Page 20 Trionic DeepClean LST For general healthcare, educational and care home environments which require regular cleaning, the design of the DeepClean LST floor mounted radiator enhances structural integrity and also incorporates specific design features: Unrivalled access for internal cleaning or routine maintenance. Patented front door (UK Patent No: 2 410 544) lies flat on floor, enabling quick access without complete door removal. Open hinge arrangement allows simple removal of door if required. Casing Depths Type 11 155 Type 12 165 Type 22 195 Outputs Outputs based upon a mean radiator water temperature of 70 C and a room temperature of 20 C Delta T 50 C. See Page 35. External Valve Location A 28 diameter cut-out for the external valve / TRV Shroud is located 80 from the top of the righthand side of the casing. If an alternative position or size is required, please advise at time of order. Standard Delivery Standard delivery comprises of Trionic LST Cover of choice, corresponding Kermi emitter (Type 11, Type 12 or Type 22 as specified) and the option of an anti-ligature TRV shroud and 9231-63 Herz External TRV kit (suitable for 15 copper to copper connection on a two pipe system) or a 9210-13 Herz internal TRV kit. An optional rotary valve is available. Alternative Herz fittings can be quoted for and supplied upon request. Covers and shrouds can be supplied on a separate delivery, helping to avoid on site damage. Rad Length Casing Length 400 600 500 700 600 800 700 900 800 1000 900 1100 1000 1200 1100 1300 1200 1400 1400 1600 1600 1800 1800 2000 Rad Height Casing Height Type 11 400 500 600 650 750 850 DSF116506 DSF117506 DSF118506 Watts T50 248 299 349 DSF116507 DSF117507 DSF118507 Watts T50 311 374 436 DSF116508 DSF117508 DSF118508 Watts T50 372 449 522 DSF116509 DSF117509 DSF118509 Watts T50 434 523 610 DSF116510 DSF117510 DSF118510 Watts T50 497 598 697 DSF116511 DSF117511 DSF118511 Watts T50 558 673 784 DSF116512 DSF117512 DSF118512 Watts T50 620 748 871 DSF116513 DSF117513 DSF118513 Watts T50 683 822 959 DSF116514 DSF117514 DSF118514 Watts T50 744 897 1,046 DSF116516 DSF117516 DSF118516 Watts T50 869 1,047 1,220 DSF116518 DSF117518 DSF118518 Watts T50 992 1,196 1,395 DSF116520 DSF117520 DSF118520 Watts T50 1,117 1,346 1,568 W: www.contourcasings.co.uk E: sales@contourcasings.co.uk T: 01952 290 498 F: 01952 210 261

Page 21 > Floor Mounted > Square Top Depth > Types 11, 12 & 22 Height Length Type 12 Type 22 750 500 600 750 400 500 600 750 1000 750 850 1000 650 750 850 1000 DSF111006 DSF127506 DSF128506 DSF121006 DSF227506 DSF228506 DSF221006 422 378 438 525 513 593 708 DSF111007 DSF127507 DSF128507 DSF121007 DSF227507 DSF228507 DSF221007 528 473 547 657 642 741 885 DSF111008 DSF127508 DSF128508 DSF121008 DSF226508 DSF227508 DSF228508 DSF221008 633 568 656 788 644 770 890 1,061 DSF111009 DSF127509 DSF128509 DSF121009 DSF226509 DSF227509 DSF228509 DSF221009 739 662 765 919 752 898 1,038 1,238 DSF111010 DSF127510 DSF128510 DSF121010 DSF226510 DSF227510 DSF228510 DSF221010 844 757 875 1,050 860 1,026 1,186 1,415 DSF111011 DSF127511 DSF128511 DSF121011 DSF226511 DSF227511 DSF228511 DSF221011 950 852 984 1,182 967 1,154 1,335 1,591 DSF111012 DSF127512 DSF128512 DSF121012 DSF226512 DSF227512 DSF228512 DSF221012 1,055 946 1,094 1,313 1,074 1,282 1,483 1,768 DSF111013 DSF127513 DSF128513 DSF121013 DSF226513 DSF227513 DSF228513 DSF221013 1,161 1,040 1,203 1,444 1,182 1,411 1,631 1,946 DSF111014 DSF127514 DSF128514 DSF121014 DSF226514 DSF227514 DSF228514 DSF221014 1,266 1,136 1,313 1,575 1,290 1,539 1,779 2,123 DSF111016 DSF127516 DSF128516 DSF121016 DSF226516 DSF227516 DSF228516 1,477 1,324 1,532 1,838 1,504 1,796 2,076 DSF127518 DSF128518 DSF226518 DSF227518 DSF228518 1,514 1,751 1,719 2,052 2,373 DSF127520 DSF128520 DSF226520 DSF227520 DSF228520 1,703 1,969 1,934 2,309 2,669

Page 22 Trionic DeepClean LST For general healthcare, educational and care home environments which require regular cleaning, the DeepClean LST wall mounted radiator incorporates specific design features: Unrivalled access for internal cleaning or routine maintenance. Patented front door (UK Patent No: 2 410 544) lies flat on floor, enabling quick access without complete door removal. Open hinge arrangement allows simple removal of door if required. Casing Depths Type 11 155 Type 12 165 Type 22 195 Outputs Outputs based upon a mean radiator water temperature of 70 C and a room temperature of 20 C Delta T 50 C. See Page 35. External Valve Location A 28 diameter cut-out for the external valve / TRV Shroud is located 80 from the top of the righthand side of the casing. If an alternative position or size is required, please advise at time of order. Standard Delivery Standard delivery comprises of Trionic LST Cover of choice, corresponding Kermi emitter (Type 11, Type 12 or Type 22 as specified) and the option of an anti-ligature TRV shroud and 9231-63 Herz External TRV kit (suitable for 15 copper to copper connection on a two pipe system) or a 9210-13 Herz internal TRV kit. An optional rotary valve is available. Alternative Herz fittings can be quoted for and supplied upon request. Covers and shrouds can be supplied on a separate delivery, helping to avoid on site damage. Rad Length Casing Length 400 600 500 700 600 800 700 900 800 1000 900 1100 1000 1200 1100 1300 1200 1400 1400 1600 1600 1800 1800 2000 Rad Height Casing Height Type 11 400 500 600 550 650 750 DSW115506 DSW116506 DSW117506 Watts T50 254 306 357 DSW115507 DSW116507 DSW117507 Watts T50 318 382 446 DSW115508 DSW116508 DSW117508 Watts T50 380 459 534 DSW115509 DSW116509 DSW117509 Watts T50 444 535 623 DSW115510 DSW116510 DSW117510 Watts T50 508 612 713 DSW115511 DSW116511 DSW117511 Watts T50 571 688 802 DSW115512 DSW116512 DSW117512 Watts T50 634 764 891 DSW115513 DSW116513 DSW117513 Watts T50 698 841 980 DSW115514 DSW116514 DSW117514 Watts T50 761 917 1,069 DSW115516 DSW116516 DSW117516 Watts T50 888 1,070 1,248 DSW115518 DSW116518 DSW117518 Watts T50 1,015 1,223 1,426 DSW115520 DSW116520 DSW117520 Watts T50 1,142 1,376 1,603 W: www.contourcasings.co.uk E: sales@contourcasings.co.uk T: 01952 290 498 F: 01952 210 261

Page 23 > Wall Mounted > Square Top Depth > Types 11, 12 & 22 Height Length Type 12 Type 22 750 500 600 750 400 500 600 750 900 650 750 900 550 650 750 900 DSW119006 DSW126506 DSW127506 DSW129006 DSW226506 DSW227506 DSW229006 431 387 448 537 524 606 723 DSW119007 DSW126507 DSW127507 DSW129007 DSW226507 DSW227507 DSW229007 540 484 560 672 656 758 905 DSW119008 DSW126508 DSW127508 DSW129008 DSW225508 DSW226508 DSW227508 DSW229008 647 581 671 805 659 787 910 1,085 DSW119009 DSW126509 DSW127509 DSW129009 DSW225509 DSW226509 DSW227509 DSW229009 755 677 783 940 769 918 1,061 1,266 DSW119010 DSW126510 DSW127510 DSW129010 DSW225510 DSW226510 DSW227510 DSW229010 863 774 895 1,074 879 1,049 1,213 1,447 DSW119011 DSW126511 DSW127511 DSW129011 DSW225511 DSW226511 DSW227511 DSW229011 971 871 1,006 1,208 988 1,180 1,365 1,627 DSW119012 DSW126512 DSW127512 DSW129012 DSW225512 DSW226512 DSW227512 DSW229012 1,078 967 1,118 1,342 1,098 1,311 1,516 1,808 DSW119013 DSW126513 DSW127513 DSW129013 DSW225513 DSW226513 DSW227513 DSW229013 1,187 1,064 1,230 1,477 1,208 1,442 1,668 1,989 DSW119014 DSW126514 DSW127514 DSW129014 DSW225514 DSW226514 DSW227514 DSW229014 1,294 1,161 1,342 1,611 1,319 1,573 1,819 2,170 DSW119016 DSW126516 DSW127516 DSW129016 DSW225516 DSW226516 DSW227516 1,510 1,354 1,566 1,879 1,538 1,836 2,123 DSW126518 DSW127518 DSW225518 DSW226518 DSW227518 1,548 1,790 1,757 2,098 2,426 DSW126520 DSW127520 DSW225520 DSW226520 DSW227520 1,742 2,013 1,977 2,361 2,729

Page 24 Trionic DeepClean LST For general healthcare, educational and care home environments which require regular cleaning, the design of the DeepClean LST floor mounted radiator enhances structural integrity. It has a gradient top preventing the casing being used as a rest surface and also incorporates specific design features: Unrivalled access for internal cleaning or routine maintenance. Patented front door (UK Patent No: 2 410 544) lies flat on floor, enabling quick access without complete door removal. Open hinge arrangement allows simple removal of door if required. Casing Depths Type 11 155 Type 12 165 Type 22 195 Outputs Outputs based upon a mean radiator water temperature of 70 C and a room temperature of 20 C Delta T 50 C. See Page 35. External Valve Location A 28 diameter cut-out for the external valve / TRV Shroud is located 80 from the top of the righthand side of the casing. If an alternative position or size is required, please advise at time of order. Standard Delivery Standard delivery comprises of Trionic LST Cover of choice, corresponding Kermi emitter (Type 11, Type 12 or Type 22 as specified) and the option of an anti-ligature TRV shroud and 9231-63 Herz External TRV kit (suitable for 15 copper to copper connection on a two pipe system) or a 9210-13 Herz internal TRV kit. An optional rotary valve is available. Alternative Herz fittings can be quoted for and supplied upon request. Covers and shrouds can be supplied on a separate delivery, helping to avoid on site damage. Rad Length Casing Length 400 600 500 700 600 800 700 900 800 1000 900 1100 1000 1200 1100 1300 1200 1400 1400 1600 1600 1800 1800 2000 Rad Height Casing Height Type 11 400 500 600 680 780 880 DGF116806 DGF117806 DGF118806 Watts T50 257 309 361 DGF116807 DGF117807 DGF118807 Watts T50 321 386 451 DGF116808 DGF117808 DGF118808 Watts T50 385 464 540 DGF116809 DGF117809 DGF118809 Watts T50 449 541 630 DGF116810 DGF117810 DGF118810 Watts T50 513 618 720 DGF116811 DGF117811 DGF118811 Watts T50 577 696 811 DGF116812 DGF117812 DGF118812 Watts T50 641 773 901 DGF116813 DGF117813 DGF118813 Watts T50 706 850 991 DGF116814 DGF117814 DGF118814 Watts T50 769 927 1,081 DGF116816 DGF117816 DGF118816 Watts T50 898 1,082 1,261 DGF116818 DGF117818 DGF118818 Watts T50 1,026 1,236 1,442 DGF116820 DGF117820 DGF118820 Watts T50 1,155 1,391 1,621 W: www.contourcasings.co.uk E: sales@contourcasings.co.uk T: 01952 290 498 F: 01952 210 261

Page 25 > Floor Mounted > Gradient Top Depth > Types 11, 12 & 22 Height Length Type 12 Type 22 750 500 600 750 400 500 600 750 1030 785 885 1035 695 795 895 1045 DGF111006 DGF127806 DGF128806 DGF121006 DGF227906 DGF228906 DGF221006 436 391 453 543 530 613 731 DGF111007 DGF127807 DGF128807 DGF121007 DGF227907 DGF228907 DGF221007 546 489 566 679 663 766 914 DGF111008 DGF127808 DGF128808 DGF121008 DGF226908 DGF227908 DGF228908 DGF221008 654 587 678 814 666 796 920 1,097 DGF111009 DGF127809 DGF128809 DGF121009 DGF226909 DGF227909 DGF228909 DGF221009 764 684 791 950 777 928 1,073 1,280 DGF111010 DGF127810 DGF128810 DGF121010 DGF226910 DGF227910 DGF228910 DGF221010 872 782 904 1,086 889 1,061 1,226 1,463 DGF111011 DGF127811 DGF128811 DGF121011 DGF226911 DGF227911 DGF228911 DGF221011 982 880 1,018 1,222 999 1,193 1,380 1,645 DGF111012 DGF127812 DGF128812 DGF121012 DGF226912 DGF227912 DGF228912 DGF221012 1,090 978 1,131 1,357 1,110 1,326 1,533 1,828 DGF111013 DGF127813 DGF128813 DGF121013 DGF226913 DGF227913 DGF228913 DGF221013 1,200 1,075 1,244 1,493 1,222 1,458 1,686 2,011 DGF111014 DGF127814 DGF128814 DGF121014 DGF226914 DGF227914 DGF228914 DGF221014 1,308 1,174 1,357 1,628 1,333 1,591 1,839 2,194 DGF111016 DGF127816 DGF128816 DGF121016 DGF226916 DGF227916 DGF228916 1,526 1,369 1,583 1,900 1,555 1,857 2,146 DGF127818 DGF128818 DGF226918 DGF227918 DGF228918 1,565 1,810 1,777 2,122 2,453 DGF127820 DGF128820 DGF226920 DGF227920 DGF228920 1,761 2,035 1,999 2,386 2,759

Page 26 Trionic DeepClean LST For general healthcare, educational and care home environments which require regular cleaning, the DeepClean LST wall mounted radiator has a gradient top preventing the casing being used as a rest surface and also incorporates specific design features: Unrivalled access for internal cleaning or routine maintenance. Patented front door (UK Patent No: 2 410 544) lies flat on floor, enabling quick access without complete door removal. Open hinge arrangement allows simple removal of door if required. Casing Depths Type 11 155 Type 12 165 Type 22 195 Outputs Outputs based upon a mean radiator water temperature of 70 C and a room temperature of 20 C Delta T 50 C. See Page 35. External Valve Location A 28 diameter cut-out for the external valve / TRV Shroud is located 80 from the top of the righthand side of the casing. If an alternative position or size is required, please advise at time of order. Standard Delivery Standard delivery comprises of Trionic LST Cover of choice, corresponding Kermi emitter (Type 11, Type 12 or Type 22 as specified) and the option of an anti-ligature TRV shroud and 9231-63 Herz External TRV kit (suitable for 15 copper to copper connection on a two pipe system) or a 9210-13 Herz internal TRV kit. An optional rotary valve is available. Alternative Herz fittings can be quoted for and supplied upon request. Covers and shrouds can be supplied on a separate delivery, helping to avoid on site damage. Rad Length Casing Length 400 600 500 700 600 800 700 900 800 1000 900 1100 1000 1200 1100 1300 1200 1400 1400 1600 1600 1800 1800 2000 Rad Height Casing Height Type 11 400 500 600 580 680 780 DGW115806 DGW116806 DGW117806 Watts T50 259 312 365 DGW115807 DGW116807 DGW117807 Watts T50 325 391 456 DGW115808 DGW116808 DGW117808 Watts T50 389 469 546 DGW115809 DGW116809 DGW117809 Watts T50 454 547 637 DGW115810 DGW116810 DGW117810 Watts T50 519 625 728 DGW115811 DGW116811 DGW117811 Watts T50 583 703 819 DGW115812 DGW116812 DGW117812 Watts T50 648 781 910 DGW115813 DGW116813 DGW117813 Watts T50 713 859 1,002 DGW115814 DGW116814 DGW117814 Watts T50 777 937 1,093 DGW115816 DGW116816 DGW117816 Watts T50 908 1,094 1,275 DGW115818 DGW116818 DGW117818 Watts T50 1,037 1,250 1,457 DGW115820 DGW116820 DGW117820 Watts T50 1,167 1,406 1,639 W: www.contourcasings.co.uk E: sales@contourcasings.co.uk T: 01952 290 498 F: 01952 210 261

Page 27 > Wall Mounted > Gradient Top Depth > Types 11, 12 & 22 Height Length Type 12 Type 22 750 500 600 750 400 500 600 750 930 685 785 935 595 695 795 945 DGW111006 DGW126806 DGW127806 DGW129306 DGW226906 DGW227906 DGW229406 441 395 458 549 536 619 739 DGW111007 DGW126807 DGW127807 DGW129307 DGW226907 DGW227907 DGW229407 551 495 572 686 671 775 924 DGW111008 DGW126808 DGW127808 DGW129308 DGW225908 DGW226908 DGW227908 DGW229408 661 593 685 823 673 804 930 1,109 DGW111009 DGW126809 DGW127809 DGW129309 DGW225909 DGW226909 DGW227909 DGW229409 772 692 800 961 786 938 1,084 1,294 DGW111010 DGW126810 DGW127810 DGW129310 DGW225910 DGW226910 DGW227910 DGW294010 882 791 914 1,097 898 1,072 1,240 1,479 DGW111011 DGW126811 DGW127811 DGW129311 DGW225911 DGW226911 DGW227911 DGW229411 992 890 1,029 1,235 1,010 1,206 1,395 1,663 DGW111012 DGW126812 DGW127812 DGW129312 DGW225912 DGW226912 DGW227912 DGW229412 1,102 989 1,143 1,372 1,123 1,340 1,549 1,848 DGW111013 DGW126813 DGW127813 DGW129313 DGW225913 DGW226913 DGW227913 DGW229413 1,213 1,087 1,257 1,509 1,235 1,474 1,705 2,033 DGW111014 DGW126814 DGW127814 DGW129314 DGW225914 DGW226914 DGW227914 DGW229414 1,322 1,187 1,372 1,646 1,348 1,608 1,859 2,218 DGW111016 DGW126816 DGW127816 DGW129316 DGW225916 DGW226916 DGW227916 1,543 1,384 1,601 1,920 1,572 1,877 2,170 DGW126818 DGW127818 DGW225918 DGW226918 DGW227918 1,582 1,829 1,796 2,145 2,479 DGW126820 DGW127820 DGW225920 DGW226920 DGW227920 1,780 2,057 2,021 2,412 2,789

Page 28 Trionic Classic LST For use in environments where safe surface temperatures are a priority, the design of the Classic LST floor mounted radiator enhances structural integrity and incorporates specific design features: Hinged doors at either end facilitate quick access to valves and controls, also enabling cleaning to the interior of the guard. Casing Depths Type 11 135 Type 12 150 Type 22 175 Outputs Outputs based upon a mean radiator water temperature of 70 C and a room temperature of 20 C Delta T 50 C. See Page 35. External Valve Location A 28 diameter cut-out for the external valve / TRV Shroud is located 80 from the top of the righthand side of the casing. If an alternative position or size is required, please advise at time of order. Standard Delivery Standard delivery comprises of Trionic LST Cover of choice, corresponding Kermi emitter (Type 11, Type 12 or Type 22 as specified) and the option of an anti-ligature TRV shroud and 9231-63 Herz External TRV kit (suitable for 15 copper to copper connection on a two pipe system) or a 9210-13 Herz internal TRV kit. Alternative Herz fittings can be quoted for and supplied upon request. Covers and shrouds can be supplied on a separate delivery, helping to avoid on site damage. Rad Length Casing Length 400 600 500 700 600 800 700 900 800 1000 900 1100 1000 1200 1100 1300 1200 1400 1400 1600 1600 1800 1800 2000 Rad Height Casing Height Type 11 400 500 600 550 650 750 CSF115506 CSF116506 CSF117506 Watts T50 248 299 349 CSF115507 CSF116507 CSF117507 Watts T50 311 374 436 CSF115508 CSF116508 CSF117508 Watts T50 372 449 522 CSF115509 CSF116509 CSF117509 Watts T50 434 523 610 CSF115510 CSF116510 CSF117510 Watts T50 497 598 697 CSF115511 CSF116511 CSF117511 Watts T50 558 673 784 CSF115512 CSF116512 CSF117512 Watts T50 620 748 871 CSF115513 CSF116513 CSF117513 Watts T50 683 822 959 CSF115514 CSF116514 CSF117514 Watts T50 744 897 1,046 CSF115516 CSF116516 CSF117516 Watts T50 869 1,047 1,220 CSF115518 CSF116518 CSF117518 Watts T50 992 1,196 1,359 CSF115520 CSF116520 CSF117520 Watts T50 1,117 1,346 1,568 W: www.contourcasings.co.uk E: sales@contourcasings.co.uk T: 01952 290 498 F: 01952 210 261

Page 29 > Floor Mounted Depth > Square Top > Types 11, 12 & 22 Height Length Type 12 Type 22 750 500 600 750 400 500 600 750 900 650 750 900 550 650 750 900 CSF119006 CSF126506 CSF127506 CSF129006 CSF226506 CSF227506 CSF229006 422 378 438 525 513 593 708 CSF119007 CSF126507 CSF127507 CSF129007 CSF226507 CSF227507 CSF229007 528 473 547 657 642 741 885 CSF119008 CSF126508 CSF127508 CSF129008 CSF225508 CSF226508 CSF227508 CSF229008 633 568 656 788 644 770 890 1,061 CSF119009 CSF126509 CSF127509 CSF129009 CSF225509 CSF226509 CSF227509 CSF229009 739 662 765 919 752 898 1,038 1,238 CSF119010 CSF126510 CSF127510 CSF129010 CSF225510 CSF226510 CSF227510 CSF229010 844 757 875 1,050 860 1,026 1,186 1,415 CSF119011 CSF126511 CSF127511 CSF129011 CSF225511 CSF226511 CSF227511 CSF229011 950 852 984 1,182 967 1,154 1,335 1,591 CSF119012 CSF126512 CSF127512 CSF129012 CSF225512 CSF226512 CSF227512 CSF229012 1,055 946 1,094 1,313 1,074 1,282 1,483 1,768 CSF119013 CSF126513 CSF127513 CSF129013 CSF225513 CSF226513 CSF227513 CSF229013 1,161 1,040 1,203 1,444 1,182 1,411 1,631 1,946 CSF119014 CSF126514 CSF127514 CSF129014 CSF225514 CSF226514 CSF227514 CSF229014 1,266 1,136 1,313 1,575 1,290 1,539 1,779 2,123 CSF119016 CSF126516 CSF127516 CSF129016 CSF225516 CSF226516 CSF227516 1,477 1,324 1,532 1,838 1,504 1,796 2,076 CSF126518 CSF127518 CSF225518 CSF226518 CSF227518 1,514 1,751 1,719 2,052 2,373 CSF126520 CSF127520 CSF225520 CSF226520 CSF227520 1,703 1,969 1,934 2,309 2,669

Page 30 Trionic Classic LST For environments where safe surface temperatures are a priority, the Classic LST wall mounted radiator incorporates specific design features. Hinged doors at either end facilitate quick access to valves and controls, also enabling cleaning to the interior of the guard. Casing Depths Type 11 135 Type 12 150 Type 22 175 Outputs Outputs based upon a mean radiator water temperature of 70 C and a room temperature of 20 C Delta T 50 C. See Page 35. External Valve Location A 28 diameter cut-out for the external valve / TRV Shroud is located 80 from the top of the righthand side of the casing. If an alternative position or size is required, please advise at time of order. Standard Delivery Standard delivery comprises of Trionic LST Cover of choice, corresponding Kermi emitter (Type 11, Type 12 or Type 22 as specified) and the option of an anti-ligature TRV shroud and 9231-63 Herz External TRV kit (suitable for 15 copper to copper connection on a two pipe system) or a 9210-13 Herz internal TRV kit. Alternative Herz fittings can be quoted for and supplied upon request. Covers and shrouds can be supplied on a separate delivery, helping to avoid on site damage. Rad Length Casing Length 400 600 500 700 600 800 700 900 800 1000 900 1100 1000 1200 1100 1300 1200 1400 1400 1600 1600 1800 1800 2000 Rad Height Casing Height Type 11 400 500 600 550 650 750 CSW115506 CSW116506 CSW117506 Watts T50 254 306 357 CSW115507 CSW116507 CSW117507 Watts T50 318 382 446 CSW115508 CSW116508 CSW117508 Watts T50 380 459 534 CSW115509 CSW116509 CSW117509 Watts T50 444 535 623 CSW115510 CSW116510 CSW117510 Watts T50 508 612 713 CSW115511 CSW116511 CSW117511 Watts T50 571 688 802 CSW115512 CSW116512 CSW117512 Watts T50 634 764 891 CSW115513 CSW116513 CSW117513 Watts T50 698 841 980 CSW115514 CSW116514 CSW117514 Watts T50 761 917 1,069 CSW115516 CSW116516 CSW117516 Watts T50 888 1,070 1,248 CSW115518 CSW116518 CSW117518 Watts T50 1,015 1,223 1,426 CSW115520 CSW116520 CSW117520 Watts T50 1,142 1,376 1,603 W: www.contourcasings.co.uk E: sales@contourcasings.co.uk T: 01952 290 498 F: 01952 210 261

Page 31 > Wall Mounted > Square Top Depth > Types 11, 12 & 22 Height Length Type 12 Type 22 750 500 600 750 400 500 600 750 900 650 750 900 550 650 750 900 CSW119006 CSW126506 CSW127506 CSW129006 CSW226506 CSW227506 CSW229006 431 387 448 537 524 606 723 CSW119007 CSW126507 CSW127507 CSW129007 CSW226507 CSW227507 CSW229007 540 484 560 672 656 758 905 CSW119008 CSW126508 CSW127508 CSW129008 CSW225508 CSW226508 CSW227508 CSW229008 647 581 671 805 659 787 910 1,085 CSW119009 CSW126509 CSW127509 CSW129009 CSW225509 CSW226509 CSW227509 CSW229009 755 677 783 940 769 918 1,061 1,266 CSW119010 CSW126510 CSW127510 CSW129010 CSW225510 CSW226510 CSW227510 CSW229010 863 774 895 1,074 879 1,049 1,213 1,447 CSW119011 CSW126511 CSW127511 CSW129011 CSW225511 CSW226511 CSW227511 CSW229011 971 871 1,006 1,208 988 1,180 1,365 1,627 CSW119012 CSW126512 CSW127512 CSW129012 CSW225512 CSW226512 CSW227512 CSW229012 1,078 967 1,118 1,342 1,098 1,311 1,516 1,808 CSW119013 CSW126513 CSW127513 CSW129013 CSW225513 CSW226513 CSW227513 CSW229013 1,187 1,064 1,230 1,477 1,208 1,442 1,668 1,989 CSW119014 CSW126514 CSW127514 CSW129014 CSW225514 CSW226514 CSW227514 CSW229014 1,294 1,161 1,342 1,611 1,319 1,573 1,819 2,170 CSW119016 CSW126516 CSW127516 CSW129016 CSW225516 CSW226516 CSW227516 1,510 1,354 1,566 1,879 1,538 1,836 2,123 CSW126518 CSW127518 CSW225518 CSW226518 CSW227518 1,548 1,790 1,757 2,098 2,426 CSW126520 CSW127520 CSW225520 CSW226520 CSW227520 1,742 2,013 1,977 2,361 2,729

Page 32 Bespoke Designs In addition to standard ranges, Contour Casings also has a distinguished history in developing bespoke LST radiators to meet your specific requirements. Wall to wall LST s To cover-up perimeter heating or Finn Pipe Systems, or to take up surplus space between an adjoining wall and a radiator, wall to wall LST s help to deliver a uniform finish. Radius Casings To follow existing angled walls or radiators, this product uses Contours internal wall fixing bracket. Free-standing Radiators For use in applications where fixings are not available to the rear of the radiator, floor mounted fixings are provided. Coloured Radiator Guards When a different aesthetic is required or in specialist environments, colour radiator guards can be manufactured. Vertical Guards For use in environments where wall space is limited, the vertical guard s contain a grille halfway up, allowing heat to dissipate at the optimum level. Aluminium Guards For application in areas of high humidity or exposure to water, Aluminium Guards can be wall mounted to facilitate cleaning underneath. W: www.contourcasings.co.uk E: sales@contourcasings.co.uk T: 01952 290 498 F: 01952 210 261

Page 33 Door Chains To prevent the front door of a radiator casing dropping to the floor, chains can be fitted to the inside of any DeepClean model as an optional safety feature, this is of particular use on oversized doors. Special Fixings A range of special fixings are available for application in environments where security and safety are an essential consideration, these include Allen Key locks, Pin Hex fastenings and key locks. Radiator Casing Cut-outs Any necessary cut-outs on the radiator casing for vinyl flooring or pipe work can be prograed into manufacture, helping to reduce installation time.

Page 34 Specifications Product Range The Trionic LST range comprises of single and double convector radiators, in four heights and lengths from 600 to 2000. Emitter The Trionic LST cover is designed to accoodate a standard Kermi Classic Radiator with Bottom-Opposite-End (BOE) connections. All standard connections are 1/2" BSP. Kermi Type 11, 12 & Type 22 steel panel convector radiators are made from steel plate St.12.03. Bead deviation 33.3. Overlapping factory fitted top grille and end panels. Brackets Kermi radiators are supplied with two fully concealed brackets which are suitable for wall mounting. For the 1800 long emitter a third bracket is included. Cover Covers are manufactured from 1.5 Zintec mild steel. The leading edges of the covers have a 25 radius, resulting in a strengthened section with rolled top front and large safe radius bullnosed corners. Covers are also available in 2 Aluminium, making them non-corrosive and suitable for use in wet rooms and other such environments. Finish Kermi radiators come with a high gloss twocoat powder coating finish. They are degreased, iron phosphated and primed with cathodic dip-coating (KTL) then electrostatically powder coated (EPS) in accordance with DIN 55900-FWA. The evenly coated paintwork is emission-free, environmentally friendly and without drips. Colour: Kermi-white (similar to RAL 9016). Covers are finished in an electrostatically applied and oven cured polyester coating to provide an attractive and durable finish. The standard finish is satin white RAL 9010. Other RAL or B.S. colours can be provided. The cover finish incorporates BioCote, the patented anti-microbial coating, which helps prevent the growth of harmful bacteria, including MRSA and E.coli, reducing the risk of hospital acquired infections. Outputs Kermi Radiator heat outputs are tested to EN442, relating to a water temperature of 75º/65ºC and a room temperature of 20ºC. Test results for each model are available on request for Delta T 60. Testing Each Kermi radiator is individually tested. Test pressure: 13.0 bar. Operating Pressure: 10.0 bar. Certified to DIN ISO 9001 standard. The construction design corresponds to the BAGUV guidelines. Quality All radiators are manufactured under a BS EN ISO 9001: 2000 quality system accepted by BSI. Warranty Each radiator is under full warranty for 5 years in respect of defective materials and manufacture. Water Treatment Please refer to Kermi for water treatment information. Thermostatic Radiator Valves As standard we supply external head TRV for 2 pipe systems. We also offer a range of other sets for different applications. Two pipe systems 9231-41 External TRV Kit (Supplied as standard) Comprising: 1 no. 9230-36 Design Sensor 1 no. 7724-91 TS-90 Angle Body 1/2" 1 no. 7350-60 Capillary & Fixing Adaptor 1 no. 3724-41 Return Valve Angle 1/2" 2 no. 6292-01 15 Nut & Olive 9210-13 Internal TRV Kit Comprising: 1 no. 9200-30 Design Sensor 1 no. 7724-91 TS-90 Angle Body 1/2" 1 no. 3724-41 Return Valve Angle 1/2" 2 no. 6292-01 15 Nut & Olive 7463-41 Remote Sensing TRV Kit Comprising: 1 no. 9430-08 Remote Sensing Phial 2m 1 no. 7724-91 TS-90 Angle Body 1/2" 1 no. 3724-41 Return Valve Angle 1/2" 2 no. 6292-01 15 Nut & Olive 9213-63 Anti-Ligature TRV Kit Comprising: 1 no. Conical Aluminium Anti-Ligature TRV Shroud 1 no. 9200-03 Mini Turbo Sensor 1 no. 7724-91 TS-90 Angle Body 1/2" 1 no. 7350-60 Capillary & Fixing Adaptor 1 no. 3724-41 Return Valve Angle 1/2" 2 no. 6292-01 15 Nut & Olive One Pipe Systems 9230-01 External TRV Kit Comprising: 1 no. 9230-06 Design Sensor 1 no. 7724-11 TS-E Angle Body 1/2" 1 no. 7350-60 Capillary & Fixing Adaptor 1 no. 3724-01 RL-1E Return Valve 1/2" 9210-03 Internal TRV Kit Comprising: 1 no. 9200-30 Design Sensor 1 no. 7724-11 TS-E Angle Body 1/2" 1 no. 3724-01 RL-1E Return Valve 1/2" 7463-01 Remote Sensing TRV Kit Comprising: 1 no. 7430-08 Remote Sensing Phial 2m 1 no. 7724-11 TS-E Angle Body 1/2" 1 no. 3724-01 RL-1E Return Valve 1/2" W: www.contourcasings.co.uk E: sales@contourcasings.co.uk T: 01952 290 498 F: 01952 210 261

Trionic LST Technical Page 35 Calculating Delta T Requirements Method;- a. Add the flow water temperature and the return water temperature together. b. Divide the answer from a. by 2. c. From the answer b. subtract the room temperature. This gives your 'Delta T' temperature. d. Select the closest Delta T value to yours from the table, then multiply the corresponding factor by the output provided for the particular radiator to obtain the output for your calculated Delta T value. Delta T Factor Delta T Factor Delta T Factor 5 C 0.0501 30 C 0.5148 55 C 1.1319 10 C 0.1234 35 C 0.6290 60 C 1.2675 15 C 0.2091 40 C 0.7482 65 C 1.4065 20 C 0.3039 45 C 0.8720 70 C 1.5487 25 C 0.4061 50 C 1.0000 75 C 1.6940 Conversion to BTU s Multiply watts by 3.413

Page 36 Other Products Contour Casings also design, manufacture and install a wide-range of other products; these include radiator guards, wall capping solutions, Aluminium fascia and soffit, column casings, floor ducting, anti-ligature ceiling grilles and manifold guards. Ensuring the same high-quality, exceptional service and competitive prices, regardless of which product you choose. Radiator Guards Contour Casings offer a wide range of radiator covers suitable for use in a variety of applications. Supporting the range is a comprehensive service package comprising of free site surveys and a supply and fit facility. Every radiator casing incorporates the following design features; radius edges, safety grilles, slim line design, one-piece construction, BioCote protection and optional cut-outs. Anti-ligature features can be incorporated for application in secure environments; other bespoke options are also available. Pipe Casing Complimenting the safe surface temperature range, Contour Casings also supply and fit Contour-Ply pipe casings. The 8 thick coercial range is designed to withstand the rigours of demanding environments such as hospitals, clinics and schools. The 5 domestic range is suitable for care homes and other low traffic areas. Contour-Ply is available in a wide range of sizes and profiles. As standard it is supplied in a high-quality white melamine finish, other finishes are available. Manifold Guards The Contour Casing Manifold Guard provides a cover for exposed manifolds to under-floor heating systems. Access to the interior of the casing for maintenance and cleaning is facilitated by a patented front door (UK Patent No: 2 410 544) which lies flat on floor. The open hinge arrangement allows simple door removal if required. A selection of quarter-turn locks is also available. Anti-Ligature Ceiling Grille The anti-ligature ceiling grille from Contour Casings has been developed for application in secure environments, such as mental health facilities and prisons. Designed to conceal ceiling fans and ventilation systems, this product can be manufactured in a variety of sizes and shapes. The anti-ligature mesh fixed behind the grille reduces the availability of ligature points, while security fixings help to eliminate tamper points. The BioCote anti-microbial additive in the paintwork reduces the risk of bacteria and the spread of infection. W: www.contourcasings.co.uk E: sales@contourcasings.co.uk T: 01952 290 498 F: 01952 210 261

Page 37 Aluminium Soffit and Fascia System Contour Casings design and manufacture an extensive range of Aluminium fascia and soffit profiles to almost any size or shape, including curved, bullnose and elliptical designs. Sections can be made to match existing profiles and brackets and carcassing can be supplied to reduce installation time, making them the perfect choice for both refurbishment and new build projects. The secret-fix panel eliminates the presence of visible fixings, producing a seamless and uninterrupted soffit line. Contour Casings range of fascia and soffit systems can be tailored to yield both a contemporary or traditional look. Aluminium Wall Coping The Contour parapet wall coping system is a pioneering Aluminium wall capping solution, designed to produce a high-quality and professional finish to all types of walls and parapets. The wall coping system incorporates a number of outstanding features to combine a superior look with exceptional performance. Independent wind-testing certifies this product is capable of handling the most extreme weather, while the concealed fixing system yields a sleek finish. Weather-proofing is facilitated via weather sealing gaskets, preventing the ingress of water, while integral sealing pads eliminate wind-rattle. The all-aluminium construction reduces the weight load on the wall and removes the possibility of corrosion. Column Casings Contour Casings are able to offer a comprehensive range of column casings for use in a wide selection of applications. The column casings range comprises of an assortment of covers suitable for both internal and external purposes and is available in a variety of shapes, sizes and finishes. Materials include; Aluminium casings, glass reinforced polymer casings, glass reinforced gypsum casings and preformed plywood casings. Column cladding is supplied prefinished and factory assembled to speed up fitting and can be provided on a supply only or supply & fit basis. Floor Ducting The Contour Casings floor ducting system is a complete product line of galvanised steel flush floor ducting for laying pipework in screeded floors. This product is available with lids and a complete range of accessories, making it suitable for all types of refurbishment and new build projects. Designed to comply with byelaw 58-(1) of the Water Act and including a plywood coverboard which can be simply removed to allow easy access to pipe work, Contour Casings floor ducting eliminates the need for expensive and time consuming shuttering.