DOUBLE BOLT CLAMPS These double-bolt clamps are made from plated ductile iron. In the smaller sizes (3 4" to 2") they are popular for hydraulic suction lines, while larger clamps are often used for irrigation and general suction and discharge service. Part Minimum Maximum PRICE Number Size Size EACH G38 DOUBLE BOLT CLAMPS ( 3 4" - 2") Spiral double-bolt clamps are designed to provide superior sealing on corrugated PVC suction hoses such as G941W, G941WT, and G1741. Note: different manufacturers may use either a clockwise or counter-clockwise spiral in their hose. Our standard corrugated hoses spiral in the counter-clockwise direction (similar to a left hand thread), and these clamps are designed for that spiral only. For clockwise spiral clamps, specify G38WR. Part Minimum Maximum PRICE Number Size Size EACH G38W SPIRAL DOUBLE-BOLT CLAMP G38-075 1.13" 1.19" $ 4.50 G38-100 1.30" 1.50" 7.20 G38-125 1.75" 2.05" 7.60 G38-150 2." 2.30" 7.70 G38-200 2.31" 2.63" 9.30 G38 DOUBLE BOLT CLAMPS (2 1 2" - 17") G38W-200 2" $ 9.00 G38W-250 2 1 2" 10.00 G38W-300 3" 10.75 G38W-400 4" 12.10 G38W-500 5" 16.90 G38W-600 6" 18.90 G38W-800 8" 22.80 G38W-1000 10" 31.80 G38W-1200 12" 35.00 G38-250 2.38" 3.06" $ 9.40 G38-300 3.03" 3.69" 10.20 G38-400 3.50" 4.00" 10.30 G38-463 4.06" 4.56".40 G38-525 4.19" 5.00" 14.30 G38-550 5.00" 5.50" 15.20 G38-600 5.50" 6.06" 17.30 G38-639 5.69" 5.94" 18.70 G38-675 6.13" 6.88" 18.70 G38-769 6.94" 7.63" 21.70 G38-818 7.69" 8.19" 30.70 G38-875 8.25" 8.88" 30.70 G38-988 8.94" 9.88" 34.70 G38-25 9.94".38" 58.30 G38-1275.19" 13.00" 71.90 G38-1360 12.19" 14.00" 84.20 G38-1450 13.19" 15.00" 89.60 G38-1700 15.06" 17.50" 123.00 88
G29C BOLT CLAMPS G29C clamps are designed to lock into the collars provided on G23S and G29S hose stems. This feature prevents fitting pull-out. G29C clamps are plated ductile iron. Clamps have two, four, or even six bolts depending on size. G29C BOLT CLAMPS Part Nominal Hose O.D. Cross Tightening PRICE EACH Pkg Number Size Minimum Max Reference Torgue * Loose Std Pkg Qty G29C-038 3 8" 0.69" 0.88" CD 6 ft lb $ 5.10 $ 4.70 5 G29C-050AA 1 2" 0.81" 0.94" DD 6 5.40 5.00 5 G29C-050A 1 2" 0.94" 1.06" B4 12 5.40 5.00 5 G29C-050B 1 2" 1.06" 1.19" B5 12 5.90 5.30 5 G29C-075AA 3 4" 1.16" 1.28" BU9S 21 6.60 6.00 5 G29C-075A 3 4" 1.19" 1.31" BU9 21 6.60 6.00 5 G29C-075B 3 4" 1.31" 1.50" B9 21 7.50 6.90 5 G29C-075C 3 4" 1.50" 1.69" B10 21 9.10 8.10 5 G29C-100AA 1" 1.41" 1.56" 156 21.60 10.50 5 G29C-100A 1" 1.53" 1.72" BU14 21.60 10.50 5 G29C-100B 1" 1.63" 1.84" B14 21.60 10.50 5 G29C-100C 1" 1.88" 2.06" B15 21 15.50 13.90 5 G29C-125 1 1 4" 2.06" 2.25" B19 40 17.60 15.70 5 G29C-150AAA 1 1 2" 1.81" 2.00" BU22 40 19.20 17.30 5 G29C-150AA 1 1 2" 2.00" 2.22" B22 40 19.20 17.30 5 G29C-150A 1 1 2" 2.09" 2.28" BU24 40 20.60 18.50 5 G29C G29C-150B 1 1 2" 2.25" 2.44" B24 40 20.60 18.50 5 G29C-150C 1 1 2" 2.47" 2.72" B25 40 24.20 21.80 5 G29C-200AA 2" 2.34" 2.53" BU28 60 25.10 22.50 5 G29C-200A 2" 2.50" 2.78" BU29 60 25.10 22.50 5 G29C-200B 2" 2.75" 3.06" B29 60 29.20 26.20 5 G29C-200C 2" 3.09" 3.44" B30 60 50.90 45.80 5 G29C-250 2 1 2" 3.50" 3.94" B34 150 51.40 1 G29C-300AA 3" 3.50" 3.94" BU35 150 50.90 1 G29C-300A 3" 3.81" 4.19" B35 150 53.00 1 G29C-400AA 4" 4.25" 4.81" BS39 200 168.50 1 * Recommended tightening torque for dry (un-lubricated) bolts. 89
GEAR CLAMPS G7/G7M CARBON STEEL GEAR CLAMP G7 series clamps are popular in the automotive industry, and feature a stainless band and screw housing with a plated carbon steel screw. G7M bands are 5 / 16 " wide, and G7 bands are 1 / 2 " wide. G7 clamps are not recommended for underground applications or corrosive environments. Part Nom. Min. Max. PRICE EACH Pkg Number Size Size Size Loose Std Pkg Qty G7M MICRO CARBON STEEL GEAR CLAMP G8/G8M ALL STAINLESS STEEL GEAR CLAMP G8 series clamps are completely stainless steel. The G8M clamps have a 5 / 16 " wide type 301 stainless band with a type 410 stainless screw. G8 clamps have a 1 / 2 " wide, 300 series stainless band and screw. Part Nom. Min. Max. PRICE EACH Pkg Number Size Size Size Loose Std Pkg Qty G8M ALL STAINLESS MICRO GEAR CLAMP G7M-04 1 4" 0.22" 0.63" $ 0.70 $ 0.59 10 G7M-06 3 8" 0.31" 0.88" 0.71 0.60 10 G7M-08 1 2" 0.44" 1.00" 0.75 0.61 10 G7M-12 3 4" 0.56" 1.25" 0.85 0.68 10 G7M-24 1 1 2" 1.31" 2.00' 0.90 0.79 10 G7M-32 2 1 8" 1.81" 2.50" 1.40 1.25 10 G7M-36 2 1 4" 2.06" 2.75" 1.40 1.25 10 G7 CARBON STEEL GEAR CLAMPS G8M-04 1 4" 0.22" 0.63" $ 0.95 $ 0.80 10 G8M-05 5 16" 0.43" 0.71" 0.97 0.82 10 G8M-06 3 8" 0.31" 0.88" 0.99 0.84 10 G8M-08 1 2" 0.44" 1.00" 1.00 0.86 10 G8M-10 5 8" 0.50" 1.06" 1.05 0.88 10 G8M-12 3 4" 0.56" 1.25" 1.05 0.89 10 G8 ALL STAINLESS S STEEL GEAR CLAMP G7-06 3 8" 0.38" 0.88" $ 0.80 $ 0.71 10 G7-08 1 2" 0.44" 1.00" 0.80 0.72 10 G7-10 5 8" 0.56" 1.06" 0.84 0.74 10 G7-12 3 4" 0.56" 1.25" 0.86 0.76 10 G7-16 1" 0.69" 1.50" 0.88 0.77 10 G7-20 1 1 4" 0.75" 1.75" 0.90 0.78 10 G7-24 1 1 2" 1.06" 2.00" 0.90 0.79 10 G7-28 1 3 4" 1.31" 2.25" 0.98 0.86 10 G7-32 2" 1.56" 2.50" 1.00 0.87 10 G7-36 2 1 4" 1.81" 2.75" 1.05 0.92 10 G7-40 2 1 2" 2.06" 3.00" 1.10 0.99 10 G7-44 2 3 4" 2.31" 3.25" 1.25 1.08 10 G7-48 3" 2.56" 3.50" 1.25 1.10 10 G7-52 3 1 4" 2.81" 3.75" 1.30 1.15 10 G7-56 3 1 2" 3.06" 4.00" 1.35 1.20 10 G7-60 3 3 4" 3.31" 4.25" 1.35 1.20 10 G7-64 4" 2.50" 4.50" 1.35 1.20 10 G7-72 4 1 2" 3.00" 5.00" 1.35 1.20 10 G7-80 5" 3.50" 5.50" 1.50 1.30 10 G7-84 5 1 4" 3.75" 5.75" 1.50 1.30 10 G7-88 5 1 2" 4.00" 6.00" 1.55 1.35 10 G7-96 6" 4.50" 6.50" 1.65 1.45 10 G7-104 6 1 2" 5.00" 7.00" 2.10 1.80 10 G7-6 7" 5.75" 7.75" 2.60 2.30 10 G7-128 8" 6.50" 8.50" 2.80 2.40 10 G7-152 9 1 2" 2.00" 10.00" 3.20 2.75 10 G7-188 3 4" 10.25" 12.25" 3.30 2.80 10 G7-200 12 1 2".00" 13.00" 4.70 4.00 10 G7-212 13 1 4".75" 13.75" 4.80 4.10 10 G7-224 14" 12.50" 14.50" 5.00 4.20 10 G7-390 24 3 8" 22.88" 24.88" 7.70 6.80 10 G8-06 3 8" 0.44" 0.88" $ 1.10 $ 0.91 10 G8-08 1 2" 0.44" 1.00" 1.10 0.92 10 G8-10 5 8" 0.56" 1.06" 1.10 0.93 10 G8-12 3 4" 0.56" 1.25" 1.10 0.93 10 G8-16 1" 0.69" 1.50" 1.15 0.95 10 G8-20 1 1 4" 0.75" 1.75" 1.15 0.96 10 G8-24 1 1 2" 1.06" 2.00" 1.15 0.97 10 G8-28 1 3 4" 1.31" 2.25" 1.20 1.00 10 G8-32 2" 1.56" 2.50" 1.20 1.00 10 G8-36 2 1 4" 1.81" 2.75" 1.20 1.00 10 G8-40 2 1 2" 2.06" 3.00" 1.30 1.10 10 G8-44 2 3 4" 2.31" 3.25" 1.50 1.20 10 G8-48 3" 2.56" 3.50" 1.50 1.20 10 G8-52 3 1 4" 2.81" 3.75" 1.55 1.25 10 G8-56 3 1 2" 3.06" 4.00" 1.60 1.30 10 G8-60 3 3 4" 3.31" 4.25" 1.70 1.35 10 G8-64 4" 2.50" 4.50" 1.70 1.35 10 G8-72 4 1 2" 3.00" 5.00" 1.85 1.45 10 G8-80 5" 3.50" 5.50" 2.00 1.60 10 G8-84 5 1 4" 3.75" 5.75" 2.00 1.60 10 G8-88 5 1 2" 4.00" 6.00" 2.00 1.60 10 G8-96 6" 4.50" 6.50" 2.10 1.70 10 G8-104 6 1 2" 5.00" 7.00" 2.60 2.00 10 G8-6 7" 5.75" 7.75" 3.00 2.40 10 G8-128 8" 6.50" 8.50" 3.10 2.50 10 G8-152 9 1 2" 2.00" 10.00" 3.50 2.80 10 G8-164 10 1 4" 1.75" 10.75" 3.70 3.05 10 G8-188 3 4" 2.25" 12.25" 4.40 3.60 10 G8-200 12 1 2".00" 13.00" 4.50 3.70 10 G8-212 13 1 4".75" 13.75" 4.70 3.90 10 G8-248 15 1 2" 14.06" 16.00" 5.00 4.20 10 G8-270 16 7 8" 15.38" 17.38" 5.40 4.50 10 G8-312 19 1 2" 18.00" 20.00" 6.40 5.40 10 G8-390 24 3 8" 22.88" 24.88" 6.90 5.80 10 90
GEAR CLAMP RACKS GEAR CLAMP RACKS AND ASSORTMENTS Display your stainless gear clamps on this attractive point of sale rack. It holds ten of the most popular sizes of gear clamps from -03 to -28 in the back row, and ten mini bolt clamp sizes -08 to -17 in the front. PRICE Part No. Description EACH G7-WR Wire rack (clamps not included) $ 43.00 14 1 4" W X 21 1 2" H Our G92 clamp rack has been modified to hold more clamps. The 26 pegs have been lengthened to hold 10 smaller sized clamps, 9 of intermediate sizes, and 7 of the larger sizes. PRICE Part No. Description EACH G5A-RACK Wire rack (clamps not included) $ 93.00 SIZE??? FREE E WITH ORDER OF 100+ G92 OR G94 CLAMPS Part PRICE Number Description EACH G92-RACK 19 1 2"W x 32"H x 10 1 2"D $ 152.00 91
SPECIALTY GEAR CLAMPS G5 series gear clamps are manufactured entirely with grade 316 stainless steel for extra corrosion resistance. They were designed for use in marine applications where 201 and 301 stainless materials show signs of corrosion. G5 all 316 stainless clamps are ideal for use in shipbuilding, marine engine repair, water treatment plants, pulp and paper manufacturing, and chemical plants. They provide extra reliability in underground installations such as sprinkler and swimming pool piping. G5M micro series have a 1 4 " wide band, and G5 are made from 1 2 " wide band. Nom. Min. Max. PRICE EACH Pkg Part No. Size Size Size Loose Std Pkg Qty G5M TYPE 316 STAINLESS S MICRO GEAR CLAMP G7ET/G7ETM EXTENDED TANG GEAR CLAMP A continuous smooth shield underneath the serrated portion of the gear clamp prevents soft silicone hose from extruding out at high temperatures. The use of regular gear clamps on silicone hose may result in leaks and possible hose blow-off. Nom. Min. Max. PRICE EACH Pkg Part No. Size Size Size Loose Std Pkg Qty G7ETM EXTENDED TANG (SILICONE HOSE) GEAR CLAMP G5M-04 1 4" 0.31" 0.63" $ 1.15 $ 1.00 10 G5M-06 3 8" 0.44" 0.88" 1.15 1.00 10 G7ETM-04 1 4" 0.31" 0.56" $ 1.30 $ 1.15 10 G7ETM-06 3 8" 0.56" 0.88" 1.30 1.15 10 G5 TYPE 316 STAINLESS SS GEAR CLAMPS G7ET EXTENDED TANG (SILICONE HOSE) GEAR CLAMP G5-10 5 8" 0.56" 1.06" $ 1.60 $ 1.35 10 G5-12 3 4" 0.56" 1.25" 1.70 1.40 10 G5-16 1" 0.69" 1.50" 1.75 1.45 10 G5-20 1 1 4" 0.75" 1.75" 1.75 1.45 10 G5-24 1 1 2" 1.06" 2.00" 1.75 1.45 10 G5-28 1 3 4" 1.31" 2.25" 1.85 1.55 10 G5-32 2" 1.56" 2.50" 1.85 1.55 10 G5-36 2 1 4" 1.81" 2.75" 1.85 1.55 10 G5-44 2 3 4" 2.31" 3.25" 2.10 1.80 10 G5-52 3 1 4" 2.81" 3.75" 2.20 1.90 10 G5-60 3 3 4" 3.31" 4.25" 2.30 2.00 10 G5-72 4 1 2" 3.00" 5.00" 2.50 2.10 10 G8L QUICK RELEASE GEAR CLAMP Quick release clamps employ a hinged housing on the clamp screw to allow instant release and fast installation. They are useful in applications where the clamp is often disconnected, such as in filter bag systems. G8L clamps are all stainless and have a very wide range of adjustment. G7ET-08 1 2" 0.63" 0.81" $ 1.60 $ 1.45 10 G7ET-10 5 8" 0.75" 0.94" 1.60 1.45 10 G7ET-12 3 4" 0.75" 1.13" 1.60 1.45 10 G7ET-16 1" 0.81" 1.38" 1.60 1.45 10 G7ET-20 1 1 4" 1.13" 1.63" 1.60 1.45 10 G7ET-24 1 1 2" 1.19" 1.94" 1.60 1.45 10 G7ET-28 1 3 4" 1.31" 2.25" 1.70 1.55 10 G7ET-32 2" 1.56" 2.50" 1.70 1.55 10 G7ET-36 2 1 4" 1.81" 2.75" 1.85 1.70 10 G7ET-40 2 1 2" 2.06" 3.00" 1.85 1.70 10 G7ET-44 2 3 4" 2.31" 3.25" 2.20 1.90 10 G7ET-48 3" 2.56" 3.50" 2.20 1.90 10 G7ET-56 3 1 2" 3.06" 4.00" 2.20 1.90 10 G7ET-60 3 3 4" 3.31" 4.25" 2.20 1.90 10 G7ET-64 4" 2.50" 4.50" 2.60 2.30 10 92 G8L-72 4 1 2" 2.00" 5.00" $ 2.90 $ 2.60 10 G8L-88 5 1 2" 2.16" 6.00" 3.10 2.70 10 G8L-128 8" 1.75" 8.56" 4.60 4.10 10 G8L-152 9 1 2" 2.00" 10.00" 5.10 4.40 10
TYPE 316 STAINLESS GEAR CLAMPS These European style clamps (originally manufactured in Sweden and sold in the marine market under the brand names ABA and AWAB) are now manufactured in America. They feature a nonperforated band with rolled edges that provides superior sealing and prevents hose damage. In addition, the fine pitch threads and riveted housing create a clamp with a very high sealing force. In marine and corrosive applications where safety and reliability are top considerations, these premium stainless clamps are an excellent choice. Mini bolt clamps provide a sure seal on small diameter tubing and thin walled hoses. The clamp edges are rolled to prevent hose damage. These tiny clamps are made entirely with type 304 stainless material. Cross Range Price Part No. Reference mm inches Each G5A/G5AM TYPE 316 STAINLESS GEAR CLAMP Cross Range Price Part No. Reference mm inches Each G5AB TYPE 304 STAINLESS MINI BOLT CLAMP 3 8" Band Width G5AM-03 31901414 8-14 0.31-0.55 $ 3.10 G5AM-04 319017-17 0.43-0.67 3.10 G5AM-06 319020 13-20 0.51-0.79 3.10 1 2" Band Width G5AB-08 306008 7.5-8.5 0.30-0.33 $ 1.85 G5AB-09 306009 8.5-9.5 0.33-0.37 1.85 G5AB-10 306010 9.5-0.37-0.43 1.85 G5AB- 3060 10.5-12 0.41-0.47 1.85 G5AB-12 306012.5-13 0.45-0.51 1.85 G5AB-13 306013 12.5-14 0.49-0.55 1.85 G5AB-14 306014 13.5-15 0.53-0.59 1.85 G5AB-15 306015 14.5-16 0.57-0.63 1.85 G5AB-16 306016 15-17 0.59-0.67 1.85 G5AB-17 306017 16-18 0.63-0.71 1.85 G5A-04 316017-17 0.43-0.67 $ 3.40 G5A-06 316020 13-20 0.50-0.79 3.40 G5A-08 316024 15-24 0.59-0.94 3.50 G5A-10 316028 19-28 0.75-1.10 3.50 G5A-12 316032 22-32 0.87-1.26 3.60 G5A-16 316038 26-38 1.02-1.50 3.60 G5A-20 316044 32-44 1.26-1.73 3.70 G5A-24 316050 38-50 1.50-1.97 3.90 G5A-28 316057 32-57 1.26-2.24 4.55 G5A-32 316064 38-64 1.50-2.52 4.55 G5A-36 316070 44-70 1.73-2.75 4.55 93
HEAVY DUTY BOLT CLAMPS Where most T-Bolt clamps feature a plated steel fastener, ours is all stainless. This makes the KODIAK ideal for many marine clamping applications, especially where gear clamps do not provide adequate holding or tightening strength. In addition, KODIAK clamps fulfill a wide range of industrial applications such as engine coolant, water suction & discharge, and hydraulic suction. G89 clamps feature a 3/4" wide by 0.025" thick type 301 stainless band. The type 302 stainless bolt is fasted by a type 304 nylon inserted locknut. The locknut is rated to 120 C (248 F) and may be tightened to 50 inch lbs. Part Minimum Maximum PRICE Number Size Size EACH G89 KODIAK ALL STAINLESS T-BOLT CLAMP G39 T-bolt clamps are designed specifically for use with silicone coolant and turbo-charger hoses. Silicone is excellent for very high temperature service, however, it tends to soften and extrude easily when hot. Conventional clamps will seal adequately when cold, but may allow leakage or hose blow-off when hot. G39 clamps feature a spring that maintains a constant tension regardless of temperature. These clamps feature a stainless band and plated steel fastener and spring. Part Minimum Maximum PRICE Number Size Size EACH G39 SPRING LOADED (SILICONE HOSE) CLAMP G89-022 1.38" 1.52" $ 7.00 G89-024 1.50" 1.64" 7.00 G89-026 1.63" 1.88" 7.00 G89-028 1.75" 2.00" 7.20 G89-030 1.88" 2.13" 7.20 G89-032 2.00" 2.25" 7.20 G89-034 2.13" 2.38" 7.20 G89-036 2.25" 2.56" 7.30 G89-038 2.38" 2.69" 7.30 G89-040 2.50" 2.81" 7.40 G89-042 2.63" 2.94" 7.50 G89-044 2.75" 3.06" 7.50 G89-046 2.88" 3.19" 7.50 G89-049 3.06" 3.38" 7.50 G89-052 3.25" 3.56" 7.50 G39-036 2.25" 2.56" $ 7.30 G39-038 2.38" 2.69" 7.30 G39-042 2.63" 2.94" 7.30 G39-046 2.88" 3.19" 7.40 G39-050 3.13" 3.44" 7.40 G39-054 3.38" 3.69" 7.40 G39-058 3.63" 3.94" 7.50 G39-062 3.88" 4.19" 7.50 G39-066 4.13" 4.44" 7.50 G39-070 4.38" 4.69" 7.50 G39-074 4.63" 4.94" 7.50 G39-082 5.13" 5.44" 7.70 G39-090 5.63" 5.94" 7.70 G39-100 6.25" 6.56" 8.20 G89-054 3.38" 3.69" 7.50 G89-057 3.56" 3.88" 7.50 G89-061 3.81" 4.13" 7.50 G89-065 4.06" 4.38" 7.60 G89-069 4.31" 4.63" 7.60 G89-073 4.56" 4.88" 7.60 G89-077 4.81" 5.13" 7.80 G89-081 5.06" 5.38" 8.00 G89-085 5.31" 5.63" 8.00 G89-089 5.56" 5.88" 8.20 G89-096 6.00" 6.31" 8.20 G89-100 6.25" 6.56" 8.20 G89-104 6.50" 6.81" 8.20 G89-108 6.75" 7.06" 9.00 G89-6 7.25" 7.56" 9.10 G89-124 7.75" 8.06" 9.20 G89-132 8.25" 8.56" 9.80 G89-135 8.44" 8.75" 9.80 G89-148 9.25" 9.56" 10.00 G89-164 10.25" 10.56" 10.20 94
HEAVY DUTY BOLT CLAMPS The G92 bolt clamp is constructed of grade 430 stainless steel band, with a zinc plated, steel bolt. It is ideal for a variety of applications including hydraulic suction lines, truck and bus radiatorhoses, and water suction and discharge service. The unique design creates several advantages over conventional T-bolt clamps: Greater size range - these clamps are available as small as 3/4". Wider band width - in the larger sizes, the band is wider than the 3/4" band used on conventional T-bolt clamps. Easy & fast tightening - a standard socket wrench can be used. A conventional T-bolt clamp requires a deep socket as the nut is tightened on the bolt, but for these clamps, the wrench is used on the bolt head itself, so a deep socket is not required. Bevelled band edges - the bevelled edge prevents damage to the hose cover. Part Band PRICE EACH Pkg Number Range Range Width Loose Std Pkg Qty G92 HEAVY DUTY BOLT CLAMPS For customers who like the special characteristics of our heavy duty bolt clamps, but need an all stainless construction, we have the G94 clamp. G94 clamps share the same features of the G92 standard clamps but are constructed entirely of grade 304 stainless components. Part Band PRICE Number Range Range Width EACH G94 TYPE 304 ALL STAINLESS BOLT CLAMPS G92-1719 17-19mm 0.67-0.75" 0.708" $ 3.70 $ 3.30 10 G92-1921 19-21 0.75-0.83" 0.708" 3.70 3.30 10 G92-2123 21-23 0.83-0.91" 0.708" 3.70 3.30 10 G92-2325 23-25 0.91-0.98" 0.708" 3.80 3.40 10 G92-2527 25-27 0.98-1.06" 0.708" 3.80 3.40 10 G92-2729 27-29 1.06-1.14" 0.708" 3.90 3.50 10 G92-2931 29-31 1.14-1.22" 0.787" 4.70 4.20 10 G92-3134 31-34 1.22-1.34" 0.787" 4.80 4.30 10 G92-3437 34-37 1.34-1.46" 0.787" 5.00 4.50 10 G92-3740 37-40 1.46-1.57" 0.787" 5.00 4.50 10 G92-4043 40-43 1.57-1.69" 0.787" 5.00 4.50 10 G92-4347 43-47 1.69-1.85" 0.787" 5.90 5.30 10 G92-4751 47-51 1.85-2.01" 0.787" 6.10 5.50 10 G92-5155 51-55 2.01-2.17" 0.787" 6.20 5.60 10 G92-5559 55-59 2.17-2.32" 0.787" 6.50 5.80 10 G92-5963 59-63 2.32-2.48" 0.787" 6.70 6.00 10 G92-6368 63-68 2.48-2.68" 0.787" 7.20 6.50 10 G92-6873 68-73 2.68-2.87" 0.984" 9.00 8.10 10 G92-7379 73-79 2.87-3." 0.984" 9.10 8.20 10 G92-7985 79-85 3. - 3.35" 0.984" 9.50 8.50 10 G92-8591 85-91 3.35-3.58" 0.984" 9.60 8.70 10 G92-9197 91-97 3.58-3.82" 0.984" 9.80 8.90 10 G92-97104 97-104 3.82-4.09" 0.984" 10.00 9.00 10 G92-1042 104-2 4.09-4.41" 0.984" 10.50 9.50 10 G92-2121 2-121 4.41-4.76" 0.984" 10.80 9.80 10 G92-1230 121-130 4.76-5.12" 0.984".10 10.00 10 G92-130140 130-140 5.16-5.51" 1.024" 15.60 14.10 10 G92-140150 140-150 5.51-5.91" 1.024" 16.10 14.50 10 G92-150162 150-162 5.91-6.38" 1.024" 16.40 14.80 10 G92-162174 162-174 6.38-6.85" 1.024" 16.80 15.20 10 G92-174187 174-187 6.85-7.36" 1.024" 17.40 15.60 10 G92-187200 187-200 7.36-7.87" 1.024" 17.80 16.00 10 G92-200213 200-213 7.87-8.39" 1.024" 18.20 16.40 10 G92-213226 213-226 8.39-8.90" 1.024" 18.60 16.70 10 G92-226239 226-239 8.90-9.41" 1.024" 19.00 17.10 10 G92-239252 239-252 9.41-9.92" 1.024" 19.50 17.50 10 G94-1719 17-19mm 0.67-0.75" 0.708" $ 9.60 G94-1921 19-21 0.75-0.83" 0.708" 9.70 G94-2123 21-23 0.83-0.91" 0.708" 9.90 G94-2325 23-25 0.91-0.98" 0.708" 10.00 G94-2527 25-27 0.98-1.06" 0.708" 10.20 G94-2729 27-29 1.06-1.14" 0.708" 10.40 G94-2931 29-31 1.14-1.22" 0.787" 10.70 G94-3134 31-34 1.22-1.34" 0.787" 10.80 G94-3437 34-37 1.34-1.46" 0.787".10 G94-3740 37-40 1.46-1.57" 0.787".20 G94-4043 40-43 1.57-1.69" 0.787".40 G94-4347 43-47 1.69-1.85" 0.787" 12.20 G94-4751 47-51 1.85-2.01" 0.787" 12.30 G94-5155 51-55 2.01-2.17" 0.787" 12.60 G94-5559 55-59 2.17-2.32" 0.787" 12.80 G94-5963 59-63 2.32-2.48" 0.787" 12.90 G94-6368 63-68 2.48-2.68" 0.787" 13.30 G94-6873 68-73 2.68-2.87" 0.984" 18.10 G94-7379 73-79 2.87-3." 0.984" 18.70 G94-7985 79-85 3. - 3.35" 0.984" 19.10 G94-8591 85-91 3.35-3.58" 0.984" 19.50 G94-9197 91-97 3.58-3.82" 0.984" 20.00 G94-97104 97-104 3.82-4.09" 0.984" 20.40 G94-1042 104-2 4.09-4.41" 0.984" 20.90 G94-2121 2-121 4.41-4.76" 0.984" 21.30 G94-1230 121-130 4.76-5.12" 0.984" 21.60 95
PINCH CLAMPS Our standard pinch clamps are zinc plated double-ear style. The double-ear clamps have a wider clamping range than single ear types. Please note that the dash size given is stamped on the clamp and refers to the closed and open size of the clamp. For example, a G2-1518 will fit over an 18mm diameter tube and will clamp down to 15mm if fully crimped. Type 304 stainless clamps are available on special order under part number G2SS. Nom. Closed Open PRICE EACH Pkg Part No, Size Size Size Loose Std Pkg Qty G2 DOUBLE-EAR PINCH CLAMPS G2-1098 and G2-1099 are both forged tools with insulated grip handles for general service, however the 1099 features side pincers as well as the standard front pincer for crimping in tight areas. Part PRICE Number Description EACH PINCH CLAMP TOOLS G2-1098 Standard Pinchers $ 39.90 G2-0041 5 32" 0.122" 0.161" $ 0.48 $ 0.35 100 G2-0045 64" 0.138" 0.177" 0.49 0.36 100 G2-0305 3 16" 0.8" 0.197" 0.50 0.37 100 G2-0507 1 4" 0.197" 0.276" 0.50 0.37 100 G2-0709 5 16" 0.276" 0.354" 0.50 0.37 100 G2-08 3 8" 0.315" 0.433" 0.52 0.39 100 G2-13 1 2" 0.433" 0.512" 0.62 0.46 100 G2-1315 9 16" 0.512" 0.591" 0.64 0.47 100 G2-1517 19 32" 0.591" 0.669" 0.65 0.48 100 G2-1518 5 8" 0.591" 0.708" 0.72 0.55 100 G2-1720 3 4" 0.669" 0.787" 0.72 0.54 100 G2-1922 13 16" 0.748" 0.866" 1.05 0.79 100 G2-2023 7 8" 0.787" 0.905" 0.80 0.60 100 G2-2225 15 16" 0.866" 0.984" 1.25 0.92 100 G2-2327 1" 0.905" 1.063" 0.95 0.70 100 G2-2528 1 1 16" 0.984" 1.102" 1.03 0.77 100 G2-2731 1 1 8" 1.063" 1.220" 1.05 0.77 100 G2-3134 1 5 16" 1.220" 1.339" 1.40 1.04 100 G2-3437 1 7 16" 1.339" 1.457" 1.29 0.96 100 G2-3740 1 1 2" 1.457" 1.575" 1.65 1.20 100 G2-4043 1 5 8" 1.575" 1.693" 2.05 1.56 100 G2-4346 1 3 4" 1.693" 1.8" 1.39 1.03 100 G2-1099 Side Jaw Pinchers 48.50 Service kits offer clamps over a size range of 5/16" to 1", and include either the 1098 or 1099 tool, as specified in the kit part number. PINCH CLAMP KITS Single ear pinch clamps are an economical clamp for light duty low pressure applications. The band is 1/4" wide and 0.030" thick. Please note that the dash size given represents the size of the open clamp in millimeters. Other sizes are available on special order. G1SS ONE-EAR STAINLESS STEEL PINCH CLAMPS G2-SK1098 Service kit (2-ear clamps) 107.50 G2-SK1099 Service kit (2-ear clamps) 2.50 G1SS-10.5 3 8" 0.350" 0.413" $ 0.47 $ 0.31 100 G1SS-.3 7 16" 0.382" 0.445" 0.47 0.31 100 G1SS-12.3 15 32" 0.409" 0.484" 0.47 0.31 100 G1SS-13.3 1 2 0.449" 0.524" 0.47 0.32 100 G1SS-14.0 35 64" 0.469" 0.551" 0.47 0.32 100 G1SS-14.5 9 16" 0.496" 0.571" 0.47 0.32 100 G1SS-15.7 5 8" 0.543" 0.618" 0.47 0.33 100 G1SS-17.0 16" 0.595" 0.669" 0.47 0.33 100 G1SS-18.5 23 32" 0.618" 0.728" 0.47 0.34 100 G1SS-19.8 3 4" 0.669" 0.780" 0.47 0.34 100 G1SS-21.0 13 16" 0.717" 0.827" 0.47 0.34 100 G1SS-22.6 7 8" 0.780" 0.890" 0.47 0.35 100 G1SS-24.1 15 16" 0.823" 0.949" 0.47 0.35 100 G1SS-25.6 1" 0.882" 1.008" 0.47 0.35 100 G1SS-27.1 1 1 16" 0.945" 1.067" 0.47 0.36 100 G1SS-28.6 1 1 8" 1.004" 1.126" 0.47 0.36 100 G1SS-30.1 1 3 16" 1.063" 1.185" 0.57 0.37 100 G1SS-31.6 1 1 4" 1.122" 1.244" 0.57 0.37 100 G1SS-33.1 1 5 16" 1.181" 1.303" 0.57 0.38 100 G1SS-34.6 1 3 8" 1.240" 1.362" 0.57 0.40 100 G1SS-36.1 1 7 16" 1.299" 1.421" 0.57 0.44 100 G1SS-42.5 1 16" 1.551" 1.673" 0.57 0.44 100 96
PUNCH CLAMPS PUNCH CLAMP TOOLS Part Clamp Band PRICE EACH Pkg Number I.D. Width Loose Std Pkg Qty PC PLATED CARBON STEEL PUNCH CLAMPS Part PRICE Number Description EACH PUNCH CLAMP TOOLS PC-3 13 16" 16" 3 8" $ 0.70 $ 0.47 100 PC-3 1 3 8" 3 8" 0.80 0.51 100 PC-4 1" 5 8" 0.85 0.60 100 PC-5 1 1 4" 5 8" 0.90 0.63 100 PC-6 1 1 2" 5 8" 0.90 0.66 100 P-38 Economy Tool $ 60.60 PC-7 1 3 4" 5 8" 1.00 0.72 100 PC-8 2" 5 8" 1.00 0.74 100 PC-9 2 1 4" 5 8" 1.10 0.78 100 PC-10 2 1 2" 5 8" 1.15 0.92 50 PC- 2 3 4" 5 8" 1.25 0.95 50 PC-12 3" 5 8" 1.35 1.00 50 PC-14 3 1 2" 5 8" 1.35 1.00 50 PC-16 4" 5 8" 1.65 1.20 25 PC-18 4 1 2" 5 8" 1.70 1.30 25 PC-20 5" 5 8" 1.90 1.35 25 P-1 Service Tool 171.60 PC-24 6" 5 8" 2.10 1.50 25 PC-28 7" 5 8" 2.60 1.95 25 PC-32 8" 5 8" 2.90 2.15 25 PC-S TYPE 201 STAINLESS STEEL PUNCH CLAMPS P-1000 Service Tool 171.60 PC-3S 13 16" 16" 3 8" $ 1.05 $ 0.83 100 PC-3S 1 3 8" 3 8" 3 1.20 0.95 100 PC-4S 1" 5 8" 1.70 1.20 100 PC-5S 1 1 4" 5 8" 1.75 1.25 100 PC-6S 1 1 2" 5 8" 1.90 1.40 100 PC-7S 1 3 4" 5 8" 2.00 1.45 100 PC-8S 2" 5 8" 2.20 1.60 100 PC-9S 2 1 4" 5 8" 2.20 1.60 100 PC-10S 2 1 2" 5 8" 2.40 1.80 50 PC-S 2 3 4" 5 8" 2.50 1.85 50 PC-12S 3" 5 8" 2.70 2.00 50 PC-14S 3 1 2" 5 8" 2.90 2.20 50 PC-16S 4" 5 8" 3.20 2.40 25 PC-18S 4 1 2" 5 8" 3.50 2.70 25 PC-20S 5" 5 8" 3.70 2.90 25 PC-24S 6" 5 8" 4.40 3.30 25 PC-28S 7" 5 8" 5.50 4.50 25 PC-32S 8" 5 8" 5.80 4.70 25 97
OPEN END PUNCH CLAMPS J-LOCK CLAMPS Part Clamp Band PRICE EACH Pkg Number I.D. Width Loose Std Pkg Qty PCO OPEN END CARBON STEEL PUNCH CLAMPS Part Clamp Band PRICE EACH Pkg Number I.D. Width Loose Std Pkg Qty J-LOCK CLAMPS PCO-3 13 16" 16" 3 8" $ 3.80 $ 3.00 100 PCO-3 1 3 8" 3 8" 4.30 3.20 100 PCO-316 2" 3 8" 4.50 3.30 100 PCO-325 3 1 8" 3 8" 4.60 3.40 100 PCO-8 2" 5 8" 3.80 2.90 100 PCO-10 2 1 2" 5 8" 4.00 3.00 50 PCO-12 3" 5 8" 4.20 3.30 50 PCO-14 3 1 2" 5 8" 4.20 3.30 50 PCO-16 4" 5 8" 4.30 3.40 25 PCO-18 4 1 2" 5 8" 4.30 3.40 25 PCO-20 5" 5 8" 4.70 3.60 25 PCO-24 6" 5 8" 5.30 3.90 25 PCO-28 7" 5 8" 5.50 4.10 25 PCO-32 8" 5 8" 5.90 4.50 25 PCO-36 9" 5 8" 6.40 4.90 25 PCO-40 10" 5 8" 6.90 5.20 25 PCO-48 12" 5 8" 8.00 5.90 25 J201 13 16" 16" 3 8" $ 1.80 $ 1.30 100 J202 1 3 8" 3 8" 3 1.80 1.30 100 J203 1" 1 2" 2.00 1.60 100 J204 1 1 4" 1 2" 2.20 1.70 100 J205 1 1 2" 5 8" 2.80 2.00 100 J206 1 3 4" 5 8" 3.00 2.20 100 J207 2" 5 8" 3.30 2.50 100 J208 2 1 4" 5 8" 3.50 2.70 100 J209 2 1 2" 5 8" 3.80 2.90 100 J210 2 3 4" 3 4" 4.50 3.30 50 J2 3" 3 4" 4.90 3.70 50 J212 3 1 2" 3 4" 5.30 3.90 50 J213 4" 3 4" 5.80 4.50 25 J214 4 1 2" 3 4" 6.40 4.80 25 J215 5" 3 4" 6.80 5.10 25 J216 6" 3 4" 8.10 6.00 25 J245 2" 3 8" 2.00 1.60 25 PCO-S OPEN END STAINLESS STEEL PUNCH CLAMPS PCO-3S 1 3 8" 3 8" $ 5.10 $ 3.70 100 PCO-316S 2" 3 8" 5.30 3.90 100 PCO-325S 3 1 8" 3 8" 5.90 4.50 100 PCO-8S 2" 5 8" 5.50 4.10 100 PCO-10S 2 1 2" 5 8" 6.30 4.80 50 PCO-12S 3" 5 8" 6.80 5.10 50 PCO-14S 3 1 2" 5 8" 7.50 5.60 50 PCO-16S 4" 5 8" 7.80 5.80 25 PCO-18S 4 1 2" 5 8" 8.30 6.10 25 PCO-20S 5" 5 8" 8.90 6.70 25 PCO-24S 6" 5 8" 9.80 7.40 25 PCO-28S 7" 5 8".60 8.70 25 PCO-32S 8" 5 8" 13.30 10.00 25 PCO-36S 9" 5 8" 14.90.20 25 PCO-40S 10" 5 8" 17.10 12.80 25 PCO-48S 12" 5 8" 19.80 14.80 25 98
BAND & BUCKLE BRASS FERRULES Part Band Band Cross Length PRICE Number Width Thickness Reference (Feet) Per foot SC TYPE 201 STAINLESS STEEL BAND SC Band shown formed into double layer clamp with SB buckle attached ready for tightening. Our standard G3 ferrules are made from brass and, when installed using the crimpers shown on the next page, create a neat and secure means of attaching a variety of couplings. Part Ferrule Ferrule Hole PRICE EACH Pkg Number I.D. Length Dia. Loose Std Pkg Qty G3 BRASS HOSE FERRULE SC-6A 3/8" 0.025" C-203 100 $ 0.70 SC-8 1/2" 0.030" C-204 100 0.90 SC-10 5/8" 0.030" C-205 100 1.05 SC-12 3/4" 0.030" C-206 100 1.40 Part Band Cross PRICE EACH Pkg Number Width Reference Loose Std Pkg Qty SB TYPE 201 STAINLESS STEEL BUCKLES SB-6 3/8" C-253 $ 0.65 $ 0.50 100 SB-8 1/2" C-254 0.85 0.68 100 SB-10 5/8" C-255 1.00 0.85 100 SB-12 3/4" C-256 1.30 1.05 100 Part PRICE Number Description EACH STANDARD BANDING TOOL C-001 Standard tool (for 1/4"-3/4" wide band) $ 189.70 G3-375 0.375" 0.718" 0.265" $ 0.65 $ 0.49 100 G3-400 0.400" 0.718" 0.265" 0.65 0.49 100 G3-425 0.425" 0.718" 0.265" 0.65 0.49 100 G3-450 0.450" 0.718" 0.328" 0.65 0.49 100 G3-475 0.475" 0.718" 0.328" 0.65 0.49 100 G3L-475 0.475" 1.000" 0.328" 0.65 0.49 100 G3-500 0.500" 0.968" 0.328" 0.65 0.49 100 G3-525 0.525" 0.968" 0.375" 0.75 0.54 100 G3-550 0.550" 0.968" 0.375" 0.75 0.54 100 G3-575 0.575" 0.968" 0.406" 0.90 0.65 100 G3-600 0.600" 0.968" 0.453" 0.90 0.65 100 G3-625 0.625" 0.968" 0.453" 0.90 0.65 100 G3-650 0.650" 0.968" 0.453" 0.90 0.65 100 G3-675 0.675" 0.968" 0.500" 0.90 0.65 100 G3-700 0.700" 0.968" 0.500" 1.05 0.76 100 G3-725 0.725" 0.968" 0.500" 1.05 0.76 100 G3-750 0.750" 0.968" 0.500" 1.05 0.76 100 G3-775 0.775" 0.968" 0.593" 1.05 0.76 100 G3-800 0.800" 0.968" 0.593" 1.25 0.86 100 G3-825 0.825" 0.968" 0.687" 1.25 0.86 100 G3-850 0.850" 0.968" 0.687" 1.25 0.86 100 G3-875 0.875" 0.968" 0.750" 1.25 0.86 100 G3AB-875 0.850" 0.843" 0.687" 1.25 0.86 100 G3-900 0.900" 0.968" 0.750" 1.30 0.92 100 G3-925 0.925" 0.968" 0.750" 1.30 0.92 100 G3-950 0.950" 0.968" 0.750" 1.30 0.92 100 G3-975 0.975" 0.968" 0.875" 1.65 1.20 100 G3-1000 1.000" 0.968" 0.875" 1.90 1.35 25 G3-1025 1.025" 0.968" 0.875" 2.60 1.85 25 G3-1050 1.050" 0.968" 0.875" 2.60 1.85 25 G3-1075 1.075" 0.968" 0.875" 2.60 1.85 25 G3-00 1.100" 0.968" 0.875" 2.60 1.85 25 G3-25 1.125" 0.968" 0.875" 2.70 1.90 25 G3-50 1.150" 0.968" 0.875" 2.70 1.90 25 G3-75 1.175" 0.968" 0.875" 2.70 1.90 25 G3-1200 1.200" 0.968" 1.000" 2.80 1.95 25 G3-1250 1.250" 0.968" 1.000" 2.80 1.95 25 G3-1350 1.350" 0.968" 1.125" 3.00 2.15 25 G3-1500 1.500" 0.968" 1.125" 3.10 2.20 25 G3A ALUMINUM HOSE FERRULES G3A-550 0.550" 0.968" 0.406" $ 0.45 $ 0.35 100 G3A-650 0.650" 0.968" 0.453" 0.50 0.40 100 G3A-675 0.675" 0.968" 0.500" 0.50 0.40 100 G3A-00 1.100" 0.968" 0.875" 1.30 0.92 25 G3A-50 1.150" 0.968" 0.875" 1.30 0.92 25 G3A-1437 1.437" 0.968" 1.047" 2.80 2.05 25 J-001 J-Clamp adapter 182.30 FERRULE CRIMPERS for Ferrule Crimping machinery refer to our EQUIPMENT CATALOG G3LS LIGHT-DUTY PLATED STEEL FERRULES These light-duty steel ferrules are commonly used with G15 Double-Lock,G45 Twist-Lock, G25 Universal fittings or G23S stems. For 1/2" hoses G3LS-091 0.910" 1.250" 0.625" $ 2.2020 $ 1.60 10 G3LS-094 0.940" 1.250" 0.625" 2.20 1.60 10 For 3/4" hoses G3LS-9 1.188" 1.50" 0.875 2.60 1.90 10 99
CRIMP SLEEVES CHOOSING A STEEL SLEEVE: In general, sleeves should be to at least 1/4" shorter than the hose barb, and placed just ahead of the end barb on the fitting. Approximate barb lengths for popular fittings are given in the table below. For steam and for high pressure air service in larger sizes, G29C interlocking clamps should be used instead of steel sleeves. Steel hose ferrules are used with barbed hose fittings and are crimped on large-diameter hydraulic hose presses to create a strong, permanent and tamper-resistant hose connection. Sleeves will work with most barbed inserts, while G3F ferrules are designed to interlock with G64 and G33F hose stems. Sizes refer to the inside diameter of the ferrule before crimping. Maximum retention strength is achieved using G3F ferrules with G64 and G33C stems. Short sleeves are generally suitable for attaching G33 style combination nipples. Longer sleeves are preferred for G65 cam-locks. Part Nominal Sleeve Sleeve PRICE Number Hose Size I.D. Length EACH Hose Fitting style and barb length Size G23S G25 G33 G65 3 4" 2 3 8" 2 1 8" 1 3 8" 1 7 8" 1" 2 3 4" 2 3 4" 1 1 2" 2 1 4" 1 1 4" 3 1 2" 1 1 2" 2 1 4" 1 1 2" 3 1 2" 1 3 4" 2 1 2" 2" 4" 2 1 8" 2 3 4" 2 1 2" 2 3 4" 3 1 4" 3" 3" 4" 4" 3 7 8" 4 1 4" 5" 4 5 8" 4 3 4" 6" 5 1 8" 5 7 8" Part Nominal Sleeve Sleeve PRICE Number Hose Size I.D. Length EACH G3F PLATED STEEL INTERLOCKING FERRULES ES G3F-150 1" 1.50" 2.29" $ 6.30 G3F-163 1" 1.63" 2.29" 6.30 G3F-213 1 1 2" 2.13" 2.36" 7.15 G3F-263 2" 2.63" 2.79" 8.45 G3F-275 2" 2.75" 2.79" 8.45 G3F-363 3" 3.63" 3.94".65 G3F-375 3" 3.75" 3.94".65 G3F-463 4" 4.63" 4.19" 15.30 G3F-481 4" 4.81" 4.19" 15.30 G3F-663 6" 6.63" 5.67" 35.60 G3F-688 6" 6.88" 5.67" 35.60 G3SSF STAINLESS STEEL INTERLOCKING FERRULES G3S PLATED STEEL HOSE SLEEVES Long Sleeves G3S-3 3 4" 1.13" 13" 2.13" $ 6.00 G3S-138 3 4" 1.38" 2.13" 6.00 G3S-150 1" 1.50" 2.31" 6.20 G3S-163 1" 1.63" 2.31" 6.20 G3S-175 1" 1.75" 2.31" 6.20 G3S-213 1 1 2" 2.13" 2.38" 6.50 G3S-263 2" 2.63" 2.75" 8.50 G3S-275 2" 2.75" 2.75" 8.50 G3S-313 2 1 2" 3.13" 3.13".20 G3S-338 3" 3.38" 3.94".20 G3S-363 3" 3.63" 3.94" 15.25 G3S-369 3" 3.61" 3.94" 15.25 G3S-375 3" 3.75" 3.94" 15.25 G3S-388 3" 3.88" 3.94" 15.25 G3S-400 3" 4.00" 3.94" 15.25 G3S-438 4" 4.38" 4.19" 20.50 G3S-463 4" 4.63" 4.19" 20.50 G3S-475 4" 4.75" 4.19" 20.50 G3S-483 4" 4.83" 4.19" 20.50 Short Sleeves G3S-3S 3 4" 1.13" 1.19" 5.70 G3S-163S 1" 1.63" 1.19" 5.90 G3S-175S 1 1 4" 1.75" 1.50" 5.90 G3S-188S 1 1 4" 1.88" 1.50" 6.10 G3S-200S 1 1 2" 2.00" 1.50" 6.10 G3S-213S 2" 2.13" 2.00" 7.90 G3S-263S 2" 2.63" 2.00" 7.90 G3S-275S 2" 2.75" 2.00" 7.90 G3S-363S 3" 3.63" 2.63" 14.30 G3S-375S 3" 3.75" 2.63" 14.30 G3S-388S 3" 3.88" 2.63" 14.30 G3S-463S 4" 4.63" 3.44" 19.30 G3S-483S 4" 4.83" 3.44" 19.30 G3SS TYPE 304 STAINLESS STEEL SLEEVES G3SSF-213 1 1 2" 2.13" 2.36" $ 10.80 G3SSF-263 2" 2.63" 2.79" 13.00 G3SSF-275 2" 2.75" 2.79" 13.00 G3SSF-363 3" 3.63" 3.94" 22.30 G3SSF-375 3" 3.75" 3.94" 22.30 G3SSF-463 4" 4.63" 4.19" 49.50 G3SSF-481 4" 4.81" 4.19" 49.50 G3SS-125 3 4" 1.25" 2.13" 9.40 G3SS-138 1" 1.38" 2.13" 9.40 G3SS-150 1" 1.50" 2.31" 9.40 G3SS-163 1" 1.63" 2.31" 9.40 G3SS-175 1" 1.75" 2.31" 10.60 G3SS-188 1 1 4" 1.88" 2.38".00 G3SS-213 1 1 2" 2.13" 2.38".70 G3SS-263 2" 2.63" 2.75" 18.20 G3SS-275 2" 2.75" 2.75" 18.20 G3SS-313 2 1 2" 3.13" 3.13" 23.10 G3SS-375 3" 3.75" 3.94" 25.00 G3SS-388 3" 3.88" 3.94" 25.00 100
SUPPORT CLAMPS G6 Support Clamps are galvanized steel dipped in vinyl to prevent chafing. They feature a 3/4" wide strap and 13/32" bolt hole. G6N clamps have a 1 2" wide galvanized steel strap fitted with a rubber liner. The bolt hole measures 0.256". Part Inside PRICE EACH Pkg Number Diameter Loose Std Pkg Qty G6 SUPPORT CLAMP G6-04 1 4" $ 1.90 $ 1.50 10 G6-06 3 8" 1.50 1.20 10 G6-07 7 16" " 1.50 1.20 10 G6-08 1 2" 1.10 0.90 10 G6-09 9 16" 1.10 0.90 10 G6-10 5 8" 1.10 0.90 10 G6-1 16" 1.10 0.90 10 G6-12 3 4" 1.10 0.90 10 G6-13 13 16" 1.40 1.10 10 G6-15 15 16" 1.40 1.10 10 G6-16 1" 1.90 1.55 10 G6-17 1 1 16" 2.30 1.80 10 G6-18 1 1 8" 2.40 1.90 10 G6-19 1 3 16" 2.40 1.90 10 G6-20 1 1 4" 2.70 2.20 10 G6-21 1 5 16" 3.90 3.20 10 G6-24 1 1 2" 2.90 2.40 10 G6-25 1 9 16" 3.60 2.90 10 G6-28 1 3 4" 4.10 3.30 10 G6-29 1 13 16" 6.20 5.00 10 G6-32 2" 5.20 4.20 10 G6-33 2 1 16" 6.30 5.10 10 G6-36 2 1 4" 4.60 3.70 10 G6-44 2 3 4" 4.80 3.90 10 G6-46 2 7 8" 6.50 5.20 10 Part Inside PRICE EACH Pkg Number Diameter Loose Std Pkg Qty G6N RUBBER CUSHIONED SUPPORT CLAMPS G6N-04 1 4" $ 0.33 $ 0.27 10 G6N-06 3 8" 0.35 0.29 10 G6N-08 1 2" 0.38 0.31 10 G6N-10 5 8" 0.42 0.33 10 G6N-12 3 4" 0.47 0.38 10 G6N-14 7/8" 0.50 0.40 10 G6N-16 1" 0.55 0.42 10 G6N-18 1 1 8" 0.80 0.65 10 G6N-20 1 1 4" 0.90 0.75 10 G6N-24 1 1 2" 1.03 0.85 10 G6N-28 1 3 4" 1.15 0.95 10 G6N-32 2" 1.60 1.30 10 Our pipe and tube support clamps consist of a steel weld plate as a base, two polypropylene clamp halves, and a steel cover plate, bolted together with hex bolts. We stock the basic heavy-duty single clamps that are most commonly used in heavy industrial applications in sizes to suit common pipe and tube diameters. Often these same clamps are used to support hydraulic hose. A wide variety of special configurations are available on special order, such as stacking clamps, twin or group clamps, rail mounted systems, and so on. Lighter pattern clamps (G6L) and special materials are also available to suit custom and OEM applications. The recommended distance between supports on a piping system given in the table below can be used to calculate the total number of clamps required. At bends, clamps should be installed on both sides as close as possible to the bend. CLAMP SPACING Clamp Hole Size Support Spacing 0.23 0.50 3.3 ft 0.51 0.86 4.0 0.87 1.25 5.0 1.25 1.50 6.5 1.51 2.25 8.8 Part Block Hole Size Designed Cross PRICE Number Size in mm to fit Reference EACH G6HD HEAVY-DUTY SUPPORT CLAMPS Clamps to fit tubing Tubing O.D. G6HD-3-025 3 0.25 6.4 1 4" O.D. SPAL-3064S-PP-DPAL-AS $ 9.35 G6HD-3-038 3 0.38 9.5 3 8 SPAL-3095S-PP-DPAL-AS 9.35 G6HD-3-050 3 0.50 12.7 1 2 SPAL-3127S-PP-DPAL-AS 9.35 G6HD-3-063 3 0.63 16.0 5 8 SPAL-3160S-PP-DPAL-AS 9.35 G6HD-4-075 4 0.75 19.0 3 4 SPAL-4190S-PP-DPAL-AS 10.40 G6HD-4-100 4 1.00 25.4 1" SPAL-4254S-PP-DPAL-AS 10.40 G6HD-5-125 5 1.25 32.0 1 1 4" SPAL-5320S-PP-DPAL-AS.25 G6HD-5-150 5 1.50 38.1 1 1 2" SPAL-5381S-PP-DPAL-AS.25 G6HD-6-200 6 2.00 50.8 2" SPAL-6508S-PP-DPAL-AS 25.00 Clamps to fit steel pipe Nominal pipe size G6HD-3-054 3 0.54 13.7 1 4" I.D. SPAL-3137S-PP-DPAL-AS 9.35 G6HD-3-067 3 0.67 17.1 3 8" SPAL-3171S-PP-DPAL-AS 9.35 G6HD-4-084 4 0.84 21.3 1 2" SPAL-4213S-PP-DPAL-AS 10.40 G6HD-4-105 4 1.05 26.7 3 4" SPAL-4267S-PP-DPAL-AS 10.40 G6HD-5-131 5 1.31 33.4 1" SPAL-5334S-PP-DPAL-AS.25 G6HD-5-166 5 1.66 42.2 1 1 4" SPAL-5422S-PP-DPAL-AS.25 G6HD-6-190 6 1.90 48.3 1 1 2" SPAL-6483S-PP-DPAL-AS 25.00 G6HD-6-238 6 2.38 60.3 2" SPAL-6603S-PP-DPAL-AS 25.00 101
SUPPORT CLAMPS Our pipe and tube support clamps consist of a steel weld plate as a base, two polypropylene clamp halves, and a steel cover plate, bolted together with hex bolts. We stock the basic heavy-duty single and standard duty twin clamps that are most commonly used in heavy industrial applications in sizes to suit common pipe and tube diameters. Often these same clamps are used to support hydraulic hose. A wide variety of special configurations are available on special order, such as stacking clamps, twin or group clamps, rail mounted systems, and so on. Heavy pattern clamps (G6HD) and special materials are also available to suit custom and OEM applications. G6T STANDARD SERIES TWIN SUPPORT CLAMPS Part Block Hole Size Designed Cross PRICE Number Size in mm to fit Reference EACH Twin clamps to fit tubing Tubing O.D. G6T-1-025 1 0.25 6.4 1 4" O.D. SP1064/064D-PPGD-AS $ 4.20 G6T-1-038 1 0.38 9.5 3 8" O.D. SP1095/095D-PPGD-AS 4.20 G6T-2-050 2 0.50 12.7 1 2" O.D. SP2127/127D-PPGD-AS 4.30 G6T-2-063 2 0.63 16.0 5 8" O.D. SP2160/160D-PPGD-AS 4.30 G6T-3-075 3 0.75 19.0 3 4" O.D. SP3190/190D-PPGD-AS 5.30 G6T-3-100 3 1.00 25.4 1" O.D. SP3254/254D-PPGD-AS 5.30 G6T-4-3 4 1.13 28.6 1 1 8" O.D. SP4285/285D-PPGD-AS 6.50 G6T-5-125 5 1.25 32.0 1 1 4" O.D. SP5320/320D-PPGD-AS 8.10 G6T-5-150 5 1.50 38.1 1 1 2" O.D. SP5381/381D-PPGD-AS 8.10 Twin clamps to fit steel pipe Nominal pipe size G6T-2-054 2 0.54 13.7 1 4" I.D. SP2137/137D-PPGD-AS 4.30 G6T-2-067 2 0.67 17.1 3 8" I.D. SP2171/171D-PPGD-AS 4.30 G6T-3-084 3 0.84 21.3 1 2" I.D. SP3213/213D-PPGD-AS 5.30 G6T-4-105 4 1.05 26.7 3 4" I.D. SP4266/266D-PPGD-AS 5.30 G6T-5-131 5 1.31 33.4 1" I.D. SP5334/334D-PPGD-AS 8.10 G6T-5-166 5 1.66 42.2 1 1 4" I.D. SP5422/422D-PPGD-AS 8.10 102