TS96 PKT 90/9 Surface applied door closer Installation instructions: Pocket door track mount in 90 /9 pocket (Closer on wall)
TABLE OF CONTENTS Closer overall Technical specifications Door templates Closer setup Exploded parts list Handing of the door A. Installing the surface closer Installing the backplate Installing the surface closer 4 B. Adjustments Adjusting the closing speeds Adjusting the spring force 6 C. Installing the closer cover Installing the cover 6 Technical specifications Templates Contents Note: Refer to the included drawing for pull side door closer back plate and track mount templating. Size selection chart Closer Door Width Range Maximum Weight TS96 PKT 90/00 '-8" to 4'" 0 lb Note. Drawing is not to scale.. Dimensions are in inches/[mm].. Right hand door is shown. 4. Caution: sex nuts are required for attachment of components to unreinforced doors and to wood or plastic faced composite type fire doors, unless an alternative method is identified in the individual door manufacturer's listings.. Template is for 4-/" x 4-/" butt hinges and /4" offset pivots. 6. Maximum degree of opening is 9. 7. Minimum door width is ". 8. Adjust closer spring tension for proper closing and latching of door. 9. Adequate reinforcement by others required to install track in pocket. 0. Pocket depth is measured from the pull side face of the door at maximum opening.. Requires DORMA EM04 electromagnetic door holder. Use closer body style "B" for this installation.. Arrows on closer mounting plate point upward. DORMA USA, Inc. Dorma Drive, Drawer AC Toll-Free: 800--848 E-mail: dormaarchitectural@dorma.com 088009 06/4 Reamstown, PA 767 Fax: 800-74-974 Subject to change without notice
TS96 PKT 90/9 (closer on wall) Closer setup Follow included template to properly prepare door and frame for all accessories of the closer installation. Know the swing of the door which is being installed prior to installation. Make sure door efficiently operates prior to installing closer. Verify closer spring size prior to installation. See "Size selection chart" on page. The surface closer is comprised of the following components.. Closer body. Main arm. Track assembly 4. Pinion. Cover and end caps 6. Closing/sweep speed adjustment 7. Latch speed adjustment 8. Backcheck adjustment 9. Delayed action adjustment 0. Backplate 0 8 4 7 6 9 Handing of the door Left hand door (LH) Interior side of door Right hand door (RH) Hinge Hinge Left hand reverse door (LHR) Exterior side of door Right hand reverse door (RHR) DORMA USA, Inc. Dorma Drive, Drawer AC Toll-Free: 800--848 E-mail: dormaarchitectural@dorma.com 088009 06/4 Reamstown, PA 767 Fax: 800-74-974 Subject to change without notice
TS96 PKT 90/9 (closer on wall) A. Installing the surface closer Tools recommended Drill Bits Metal: No. & 0- Tap Wood: /8" # Phillips screwdriver M. & M Hex key Installing the back plate Reference template 088009. Attach the back plate to the installing surface using the four screws [0- machine screws or #0 wood screws] provided with the surface closer. NOTE: Make sure arrows on plate point upward. Installing the surface closer Toward the hinge NOTE: Orient pinion () closest to hinge.. Secure the closer body () to the plate using the four Mx47mm flathead Phillips screws () provided with the plate. A B C A. Position the components inside the track channel ().. Attach the track channel to the door through the end blocks with two flat head Phillips screws (). A. End block B. Track channel C. Slide shoe Right hand door 4 DORMA USA, Inc. Dorma Drive, Drawer AC Toll-Free: 800--848 E-mail: dormaarchitectural@dorma.com 088009 06/4 Reamstown, PA 767 Fax: 800-74-974 Subject to change without notice
TS96 PKT 90/9 (closer on wall) Right hand door 4 4. Align the arm () with the slide shoe of the track channel. 4. Secure with one M8xmm shoulder bolt () using an M hex key.. With the door closed and using an adjustable wrench (looking up at the bottom of the closer): Left hand door - turn the bottom pinion clockwise approximately. Right hand door - turn the bottom pinion counterclockwise approximately.. Attach the main arm () to the top pinion with an M6x0 socket head cap screw () using an M hex key. Be sure that the door is fully closed during application. Right hand door B. Adjustments Set closer spring size prior to making any closing speed adjustments. Do not back valves out beyond closer casting. Maximum opening angle is 9º. Door should close in to 6 seconds from 90º. Do not close valves completely. Adjusting the closing speeds: sweep, latch, backcheck and delayed action [Sweep] [Latch] [Backcheck] Latch Sweep 4 [Delayed action] Backcheck Decrease Increase Sweep & Latch Delayed action Increase Decrease Backcheck & Delayed actions. Adjust the sweep speed () for the area from 70-0 Increase sweep speed: Turn valve counter-clockwise Decrease sweep speed: Turn valve clockwise.. Adjust the latch speed () for the area from 7-0. Increase latch speed: Turn valve counter-clockwise Decrease latch speed: Turn valve clockwise.. Adjust the backcheck (). Increase resistance: Turn valve clockwise Decrease resistance: Turn valve counter-clockwise..4 Adjust the delayed action (4) for the area from 9-70. Increase delayed action: Turn valve clockwise Decrease delayed action: Turn valve counter-clockwise DORMA USA, Inc. Dorma Drive, Drawer AC Toll-Free: 800--848 E-mail: dormaarchitectural@dorma.com 088009 06/4 Reamstown, PA 767 Fax: 800-74-974 Subject to change without notice
TS96 PKT 90/9 (closer on wall) Adjusting the spring force Increase Decrease DOOR WIDTH FULL TURNS OF CLOSER INT. SPRING ADJUSTER SIZE TS96 4' 0 4'6" + 6 TS96 NOTE: Supplied with a size 6 spring setting. Increase force: turn clockwise 6 times (max) C. Installing the closer cover Installing the cover 4. Snap both end covers () into place.. Remove the un-needed tab (), and snap the closer body cover () into place.. Secure with a 4-40 Phillips pan head screw (4). 6 DORMA USA, Inc. Dorma Drive, Drawer AC Toll-Free: 800--848 E-mail: dormaarchitectural@dorma.com 088009 06/4 Reamstown, PA 767 Fax: 800-74-974 Subject to change without notice
DORMA USA, INC. DORMA DRIVE, DRAWER AC REAMSTOWN, PA 767 TOLL-FREE: 800--848 FAX: 800-74-974 E-MAIL: DORMAARCHITECTURAL@DORMA.COM WWW.DORMA-USA.COM 088009 06/04, Subject to change without notice