PRODUCT GUIDE DOCUMENT NUMBER REVISION DATE 20161107 NOTICE The manufacturer will accept no responsability for any electrical damage resulting from improper installation of this product, be that either damage to the vehicle itself or to the installed device. This device must be installed by a certified technician. Please review the Installation Guide carefully before beginning any work.
GETTING STARTED PAGE 2 OF 12 WELCOME Congratulations on the purchase of your VW solution. You are now a few simple steps away from enjoying your new remote starter unit with enhanced features. Before starting your installation, please ensure that your VW module is programmed with the correct firmware for your vehicle and that you carefully review the install guide. TABLE OF CONTENTS Box Contents 3 Tach Programming Procedure 4 Remote Programming Procedure 5 Valet Mode Programming Procedure 6 Compatible Accessories 7 Online Module Settings 9 Module Diagnostics 10 Remote Starter Error Codes 11 Module Reset Procedure 12 NEED HELP? 1 866 427-2999 support@idatalink.com idatalink.com/support www.12voltdata.com/forum www.facebook.com/groups/idatatech
BOX CONTENTS - 1 OF 1 PAGE 3 OF 12 BOX CONTENTS AUTOMATIC TRANSMISSION CUT LOOP M2-12 PIN BLACK MODULE M5-6 PIN BLUE 2 1 4 3 6 5 8 7 10 9 12 11 M2 01 GREEN BLACK DOT - LOCK (-) OUTPUT 02 BLUE BLACK DOT - UNLOCK (-) OUTPUT 03 RED/WHITE BLACK DOT - TRUNK RELEASE (-) OUTPUT 04 EMPTY 05 EMPTY 06 BLUE/WHITE BLACK DOT - GWR (-) OUTPUT 07 BROWN BLACK DOT - SIREN (+) OUTPUT 08 WHITE/PURPLE BLACK DOT 09 PURPLE/BLACK BLACK DOT - RAP SHUTDOWN (-) OUTPUT 10 WHITE/BLACK BLACK DOT - HORN (-) OUTPUT 11 BROWN/BLACK BLACK DOT - GROUND WHEN ARMED (-) OUTPUT 12 WHITE BLACK DOT - PARKING LIGHTS (-) OUTPUT M3-10 PIN WHITE TELEMATIC 1-4 PIN BLUE TELEMATIC 2-4 PIN RED LED 2 M4-20 PIN BLACK 2 PIN BLACK - LED PROGRAMMING BUTTON LED 1 2 4 6 8 10 1 3 5 7 9 M3 01 EMPTY 02 EMPTY 03 EMPTY 04 EMPTY 05 EMPTY 06 WHITE/BLUE SILVER DOT - X-TRIGGER (-) INPUT 07 GRAY SILVER DOT - HOOD (-) INPUT 08 EMPTY 09 EMPTY 10 TAN SILVER DOT - EXT ALARM SENSOR (-) INPUT THERMISTOR - 2 PIN BLUE NC - 4 PIN RED RF PORT/WEBLINK PORT - 4 PIN BLACK USB 1 3 5 2 4 6 M5 FUNCTIONS DEFINED BY FIRMWARE VS1 JS12 VS9 VS10 VS2 VS5 JS4 GOLF JS10 VS6 MS1 JS1 JS2 JS5 PTS VS3 2X STICKERS HOOD SWITCH JS3 JS6 KEY JS7 VS4 VS7 JS8 JS11 VS8 JS9
TACH PROGRAMMING PROCEDURE - 1 OF 1 PAGE 4 OF 12 01 OFF ACC ON START START vehicle for 15 seconds. ENGINE START STOP 02 Press and hold the brake pedal. 03 Press and release the module s programming button. (OR if the remotes are already programmed to the vehicle, press and hold the start button of the remote for 2.5 seconds.) 04 Wait, LED 2 will flash GREEN. (See the Module Diagnostics page) 05 Release the brake pedal. 06 Module Programming Procedure completed.
REMOTE PROGRAMMING PROCEDURE - 1 OF 1 PAGE 5 OF 12 01 [4x] WARNING: Complete the module programming procedure and tach programming procedure before programming the remotes. A maximum of four [4x] remotes per system. 07 Release the antenna button. The antenna s leds will turn OFF. 02 OFF ACC ON START Set ignition to ON position. 08 OFF ACC ON START Set ignition to OFF position. ENGINE START STOP ENGINE START STOP 03 Press and release the antenna button, then press and hold the antenna button. The antenna s leds will turn solid BLUE. 09 Remote Programming Procedure completed. 04 Parking Light will flash once [1x]. 05 Press once [1x] on the button of each remote. 06 The antenna s leds will flash BLUE once [1x] for each successful pairing.
VALET MODE PROGRAMMING PROCEDURE - 1 OF 1 PAGE 6 OF 12 >> NOTE: In Valet Mode, the Remote starter is not functional. Keyless entry, Lock and Unlock will remain functional. See RF kit user manual for alternate valet mode programming. 06 Valet Mode Programming Procedure completed. 01 Time restriction. Complete next step within 7 seconds. >> To exit valet mode: repeat steps 1 to 5. 02 OFF ACC ON START Cycle ignition ON twice [2x OFF/ON] rapidly. ENGINE START STOP 03 Press and release the BRAKE pedal three times [3x]. 04 Parking Light will flash once [1x] then will flash twice [2x]. 05 OFF ACC ON START Set ignition to OFF position. ENGINE START STOP
COMPATIBLE ACCESSORIES - 1 OF 2 PAGE 7 OF 12 WEBLINK CABLE (required accessory sold separately) WEBLINK CABLE MODULE WEBLINK PORT COMPUTER USB PORT 4 PIN BLACK CABLE WEBLINK MOBILE (accessory sold separately) OBDII CONNECTOR MODULE WEBLINK PORT 4 PIN BLACK CABLE MOBILE DEVICE PORT 1 2 3 4 5 6 7 8 OBDII CONNECTOR 9 10 11 12 13 14 15 16 TELEMATIC KIT (accessory sold separately) MODULE TELEMATIC BLUE PORT (NC) *For SmartStart, use the module s RED Telematic port.
COMPATIBLE ACCESSORIES - 2 OF 2 PAGE 8 OF 12 RF KIT (sold separately) MODULE RF PORT 4 PIN BLACK CABLE ANTENNA
ONLINE MODULE SETTINGS - 1 OF 1 PAGE 9 OF 12 WEB PROGRAMMABLE MENUS MENU 1 Remote Starter MENU 2 Doorlock Options MENU 3 Security Options MENU 4 AUX function assignments MENU 5 Programmable outputs (POC) MENU 6 Pulse Timer Output Configuration (PTO) MENU 7 Input Configurations MENU 8 Output Configurations Programming options are avaible through Weblink and Weblink Mobile only. DESCRIPTION RS related configuration options Convenience feature configuration options Alarm activation and settings Set transmitter AUX buttons controls Set actions for programmable outputs Set duration for pulse timer outputs (if used) Set inputs for Auto by firmware/data/analog Set outputs for Auto by firmware/data/analog
MODULE DIAGNOSTICS - 1 OF 1 PAGE 10 OF 12 TEST MODULE LED 1 STATUS DIAGNOSTIC I II III IV DURING MODULE PROGRAMMING DURING TACH PROGRAMMING DURING REMOTE START WITH IGNITION OFF Flashing RED Missing/wrong information from firmware or vehicle. Solid RED Module waiting for more vehicle information. Flashing GREEN Additional steps required to complete module programming. Solid GREEN then OFF Module correctly programmed. OFF No activity or module already programmed. 1 GREEN flash Tach signal programmed in Analog 2 GREEN flashes Tach signal programmed in Data 3 RED flashes No tach signal detected 4 RED flashes System is in valet mode 5 RED flashes Tach set for VTS. No tach programming required 6 RED flashes Tach set for assumed start. No tach programming required Flashing RED Module incorrectly programmed. Solid RED Module incorrectly programmed. Flashing GREEN Module correctly programmed and operational. Solid GREEN then OFF Reset in progress. OFF Invalid ground when running status from remote starter. Flashing RED Module incorrectly programmed or connected. Solid RED Module not programmed. Waiting for more vehicle information. Flashing GREEN False ground when running status from remote starter. Solid GREEN then OFF Reset in progress. OFF Module at rest and ready for a remote start sequence.
REMOTE STARTER ERROR CODES - 1 OF 1 PAGE 11 OF 12 REMOTE STARTER ERROR CODES: NOTES [X] NUMBER OF PARKING LIGHT FLASHES DIAGNOSTIC I II WARNING: The following applies only when the parking lights are connected and supported by the system. After a remote starter failure, the parking lights will flash three [3x] times, then will flash [X] number times to indicate an error code. See table. 01 Engine running. 02 Key in ignition at ON position. 03 Door is open. 04 Trunk is open. 05 Foot brake is ON. 06 Hood is open. 07 The reservation is OFF. (Manual transmission only) 08 Tach failure. 09 The vehicle is moving (VSS). 10 System is in Valet Mode. 11 CAN communication failure 12 RS not synchronized. Start vehicle with OEM key for 15 sec before trying a new RS sequence. 13 Bypass problem. REMOTE STARTER SHUTDOWN ERROR CODES: NOTES [Y] NUMBER OF PARKING LIGHT FLASHES DIAGNOSTIC I II WARNING: The following applies only when the parking lights are connected and supported by the system. If the engine shuts down after a remote starter sequence: Press and hold the Trunk button and the Start button at the same time for 2.5 seconds when using a 1-WAY remote. OR Press once [1x] on button 4 when using a 2-WAY remote. The parking lights will flash four [4x] times, then will flash [Y] number times to indicate an error code. See table. 01 Engine tach signal is lost. 02 Emergency brake is lost. 03 Foot brake is ON. 04 Hood is open. 05 Engine RPM limiter is ON. 06 Glow plug timeout error. 07 Vehicle is moving (VSS). 08 N/A 09 N/A 10 Door is open. 11 CAN communication failure during RS sequence. 12 RS not synchronized. Start vehicle with OEM key for 15 sec before trying a new RS sequence. 13 Takeover is not allowed. 14 Shutdown error, board overheat protection.
MODULE RESET PROCEDURE - 1 OF 1 PAGE 12 OF 12 >> The following procedure resets the module programming to the vehicle. It does not reset any settings configured online. 06 Module RESET completed. 01 Disconnect all connectors from module except the M1 BLACK 8-pin connector and the M4 BLACK 20-pin connector. 07 Reconnect all connectors. 02 Disconnect the M1 BLACK 8-pin connector and the M4 BLACK 20-pin connector. 08 Repeat programming procedure. 03 PRESS AND HOLD the module s programming button while connecting the M1 BLACK 8-pin connector and the M4 BLACK 20-pin connector. >> Failure to follow procedure may result with a DTC or a CHECK ENGINE error message. 04 Wait, LED 1 will flash RED. RELEASE programming button. 05 LED 1 will turn RED for 2 seconds.