INSTALL GUIDE FLC-NI(RS)-NI-[FLRSNI]-EN DOCUMENT NUMBER REVISION DE 000 FIRMWARE FLC-NI(RS)-NI-[FLRSNI] HARDWARE FLRSNI ACCESSORIES FLPROG (REQUIRED) FLRF// (OPTIONAL) CARLINK ASCL (OPTIONAL) NOTICE The manufacturer will accept no responsability for any electrical damage resulting from improper installation of this product, be that either damage to the vehicle itself or to the installed device. This device must be installed by a certified technician. Please review the Installation Guide carefully before beginning any work. U.S. Patent No.,,0 Automotive Data Solutions Inc. 0 BEFORE INSTALLION - Connect module to computer - Login to Weblink account - Flash firmware to module (module is not preloaded with firmware) - Use accessories accordingly (accessories are sold separately)
PAGE OF DOC.: # 000 VEHICLE LIST - OF DA IMMOBILIZER BYPASS SECURE TAKE OVER DISARM OEM ALARM DOOR LOCK DOOR UNLOCK X LOCK /STANDALONE MOD. TRUNK/HCH RELEASE DOOR STUS OUTPUT TRUNK STUS OUTPUT HOOD STUS OUTPUT** TACHOMETER OUTPUT BRAKE PEDAL STUS OUTPUT * E-BRAKE STUS OUTPUT M 0 M - M 0 M - Q0 - Q0L - QX - QX0 - Armada Cube 0- Juke - Quest - Quest (with power sliding doors) - Sentra - Versa Sedan - - Versa Note * Available only when ignition is in the ON position. ** Available only if vehicle is equipped with factory hood switch. U.S. Patent No.,,0 Automotive Data Solutions Inc. 0 FLC-NI(RS)-NI-[FLRSNI]-EN POWER SLIDING DOORS (R) INSTALL TYPE - POWER SLIDING DOORS (L) YEAR M Hybrid POWER LIFT GE MODEL NISSAN INFINITI MAKE FEURES
PAGE OF DOC.: # 000 BOX CONTENTS - OF BOX CONTENTS 0 PIN T-HARNESS VS LED BLUE BLACK BLACK 0 0 0 PROGRAMMING BUTTON LED BLACK RF PORT/ WEBLINK PORT BLUE TELEMIC PORT BLACK VS PIN VS VS A G F B E MS VS VS C D 0 OPTIONAL TERMINALS (OEM ALARM CONTROL) MS VS MS WHITE AFTERMARKET HOOD SWITCH AND CABLE VS VS VS0 WARNING STICKER VS VS WEBLINK CABLE (required accessory sold separately) WEBLINK CABLE WEBLINK PORT COMPUTER USB PORT PIN BLACK CABLE U.S. Patent No.,,0 Automotive Data Solutions Inc. 0 FLC-NI(RS)-NI-[FLRSNI]-EN
PAGE OF DOC.: # 000 COMPIBLE ACCESSORIES - OF RF KIT (accessories sold separately) FLRF// RF KIT RF PORT ANTENNA TELEMIC KIT (accessories sold separately) CARLINK FLHRNTM TELEMIC PORT TELEMIC KIT (accessories sold separately) FLHRNTM PN 00 TELEMIC PORT 0 VEHICLE OBDII PORT U.S. Patent No.,,0 Automotive Data Solutions Inc. 0 OBDII CAR CONNECTION FLC-NI(RS)-NI-[FLRSNI]-EN
PAGE OF DOC.: # 000 INFINITI M Q0 Q0L QX NISSAN QX0 Armada - - - - - U.S. Patent No.,,0 Automotive Data Solutions Inc. 0 0 pin 0 pin M pin LtGreen BCM, left of steering column B pin 0 Blue Driver kick panel M0 0 pin M0 0 pin M pin LtGreen BCM, left of steering column B pin 0 Blue Driver kick panel POSITION TYPE M0 M0 COLOR NAME COMPONENT LOCOR WIRE DESCRIPTION LOCION - POLARITY M - WIRE COLOR M Hybrid YEAR MODEL MAKE TYPE - WIRE CHART - OF M0 0 pin M0 0 pin M pin LtGreen BCM, left of steering column B pin 0 Blue Fuse box, rear side M0 0 pin M0 0 pin M pin LtGreen BCM, left of steering column B pin 0 Blue Driver kick panel M0 0 pin M0 0 pin M pin LtGreen BCM, left of steering column B pin 0 Blue Driver kick panel M 0 pin BCM, behind cluster (use provided terminal for connection) M 0 pin BCM, behind cluster (use provided terminal for connection) M pin Gray/Red BCM, behind cluster M White 0 pin B Blue/Orange Fuse box M 0 pin BCM, behind cluster (use provided terminal for connection) M 0 pin BCM, behind cluster (use provided terminal for connection) M pin Gray/Red BCM, behind cluster M White 0 pin B Blue/Orange Fuse box M 0 pin BCM, behind cluster (use provided terminal for connection) M 0 pin BCM, behind cluster (use provided terminal for connection) M pin Gray/Red BCM, behind cluster M White 0 pin B Blue/Orange Fuse box FLC-NI(RS)-NI-[FLRSNI]-EN
PAGE OF DOC.: # 000 NISSAN Quest* Quest* Versa Sedan - - - 0 pin 0 White/ BCM, driver kick panel 0 pin 0 White/Red BCM, driver kick panel M pin Brown/Yellow BCM, driver kick panel M0 pin Brown/white Driver kick panel M 0 pin 0 Red BCM near A pillar, driver side M 0 pin 0 Blue BCM near A pillar, driver side B0 pin LtBlue BCM near A pillar, driver side M 00 pin 0 Violet Driver kick panel POSITION TYPE M M COLOR NAME COMPONENT LOCOR WIRE DESCRIPTION LOCION - POLARITY Juke 0- WIRE COLOR Cube YEAR MODEL MAKE TYPE - WIRE CHART - OF M 0 pin 0 Yellow BCM, behind cluster M 0 pin 0 White BCM, behind cluster M pin Green BCM, behind cluster M 0 pin B LtBlue Fuse box M 0 pin 0 Gray BCM, behind cluster M 0 pin 0 Brown BCM, behind cluster M pin Green BCM, behind cluster M 0 pin B Pink Fuse box M 0 pin 0 Gray BCM near A pillar, driver side M 0 pin 0 White BCM near A pillar, driver side B0 Pin LtBlue BCM near A pillar, driver side B pin 0 Blue Driver kick panel * Model without power sliding doors U.S. Patent No.,,0 Automotive Data Solutions Inc. 0 FLC-NI(RS)-NI-[FLRSNI]-EN
PAGE OF DOC.: # 000 TYPE - WIRING DIAGRAM - OF OBDII (UNDER DRIVER SIDE DASH) VS A G RF PORT/WEBLINK PORT B F TELEMIC PORT PIN OBDII E C VS D 0 PIN OBDII HARNESS MS A MS BRAKE SWITCH RELAY VS PIN BRAKE E VS B E PIN BRAKE HARNESS VS MS VS0 PIN VS VS VS IMMO PIN IMMO VS PIN IMMO HARNESS WHITE HORN BCM A A DRIVER DOOR PIN - 0 PARKING LIGHT SEE WIRE CHART OPTIONAL D 0 ACC O ENGINE VS 0 BROWN/BLACK 0 GRAY - RAP SHUTDOWN OUTPUT 0 EMPTY 0 EMPTY 0 EMPTY 0 PURPLE/GREEN - LOCK OUTPUT 0 EMPTY 0 BLUE/GREEN 0 EMPTY 0 EMPTY GRAY/GREEN - HORN OUTPUT DKGREEN/GREEN - UNLOCK OUTPUT CK 0 PIN HARNESS VS C N 0 0 LO LOCK/ARM UNLOCK/DISARM 0 GRAY/WHITE - HOOD STUS INPUT B SEE WIRE CHART B THERE MAY BE NO WIRE CONNECTED TO THESE PINS, USE PROVIDED TERMINALS. WITHOUT OEM HOOD SWITCH: INSTALL AND CONNECT TO AFTERMARKET HOOD SWITCH A B AFTERMARKET HOOD SWITCH 0 0 0 0 U.S. Patent No.,,0 Automotive Data Solutions Inc. 0 FLC-NI(RS)-NI-[FLRSNI]-EN
PAGE OF DOC.: # 000 Quest* POLARITY LOCION COMPONENT LOCOR M 0 pin BCM, behind cluster (use provided terminal for connection) M pin Green BCM, behind cluster POSITION WIRE COLOR TYPE - COLOR Quest* NAME YEAR WIRE DESCRIPTION MODEL NISSAN MAKE TYPE - WIRE CHART - OF M 0 pin B LtBlue Fuse box M 0 pin BCM, behind cluster (use provided terminal for connection) M pin Green BCM, behind cluster M 0 pin B Pink Fuse box - * Model with power sliding doors U.S. Patent No.,,0 Automotive Data Solutions Inc. 0 FLC-NI(RS)-NI-[FLRSNI]-EN
PAGE OF DOC.: # 000 TYPE - WIRING DIAGRAM - OF OBDII (UNDER DRIVER SIDE DASH) VS A G RF PORT/WEBLINK PORT B F TELEMIC PORT PIN OBDII E C VS D 0 PIN OBDII HARNESS MS A MS BRAKE SWITCH RELAY VS PIN BRAKE E VS B VS VS0 MS PIN VS VS VS ENGINE VS IMMO PIN IMMO 0 0 BROWN/BLACK 0 GRAY - RAP SHUTDOWN OUTPUT 0 EMPTY 0 EMPTY 0 EMPTY 0 PURPLE/GREEN - LOCK OUTPUT 0 EMPTY 0 BLUE/GREEN 0 EMPTY 0 EMPTY GRAY/GREEN - HORN OUTPUT DKGREEN/GREEN VS WHITE HORN OPTIONAL BCM M DRIVER DOOR PIN - DIODE DIODE 0 GRAY/WHITE - HOOD STUS INPUT LOCK/ARM - N00 M 0 M M THERE MAY BE NO WIRE CONNECTED TO THESE PINS, USE PROVIDED TERMINALS. WITHOUT OEM HOOD SWITCH: INSTALL AND CONNECT TO AFTERMARKET HOOD SWITCH M M AFTERMARKET HOOD SWITCH U.S. Patent No.,,0 Automotive Data Solutions Inc. 0 PARKING LIGHT SEE WIRE CHART N00 PIN IMMO HARNESS D 0 ACC O PIN HARNESS VS C CK N E PIN BRAKE HARNESS 0 0 LO FLC-NI(RS)-NI-[FLRSNI]-EN 0 0 0 0
PAGE 0 OF DOC.: # 000 U.S. Patent No.,,0 Automotive Data Solutions Inc. 0 WIRE DESCRIPTION 0 pin 0 pin M pin LtGreen BCM, left of steering column Red/Blue Driver kick panel M0 0 pin M0 0 pin M pin LtGreen BCM, left of steering column Red/Blue Driver kick panel POSITION TYPE M0 M0 COLOR NAME COMPONENT LOCOR 0 LOCION 0 POLARITY M YEAR MODEL M WIRE COLOR INFINITI MAKE TYPE - WIRE CHART - OF FLC-NI(RS)-NI-[FLRSNI]-EN
PAGE OF DOC.: # 000 TYPE - WIRING DIAGRAM - OF OBDII (UNDER DRIVER SIDE DASH) VS A G RF PORT/WEBLINK PORT B F TELEMIC PORT PIN OBDII E C VS D 0 PIN OBDII HARNESS MS A MS BRAKE SWITCH RELAY VS PIN BRAKE E VS B E PIN BRAKE HARNESS VS MS VS0 PIN VS VS ACC O VS 0 BROWN/BLACK 0 GRAY - RAP SHUTDOWN OUTPUT 0 EMPTY 0 EMPTY 0 EMPTY 0 PURPLE/GREEN - LOCK OUTPUT 0 EMPTY 0 BLUE/GREEN 0 EMPTY 0 EMPTY GRAY/GREEN - HORN OUTPUT DKGREEN/GREEN - UNLOCK OUTPUT IMMO PIN IMMO PIN IMMO HARNESS WHITE PARKING LIGHT SEE WIRE CHART HORN OPTIONAL BCM M DRIVER DOOR PIN - M 0 LOCK/ARM - UNLOCK/DISARM - 0 GRAY/WHITE - HOOD STUS INPUT M0 M0 M THERE MAY BE NO WIRE CONNECTED TO THESE PINS, USE PROVIDED TERMINALS. WITHOUT OEM HOOD SWITCH: INSTALL AND CONNECT TO AFTERMARKET HOOD SWITCH M0 AFTERMARKET HOOD SWITCH U.S. Patent No.,,0 Automotive Data Solutions Inc. 0 CK ENGINE D VS 0 PIN HARNESS 0 VS VS C N 0 0 LO FLC-NI(RS)-NI-[FLRSNI]-EN 0 0 0 0
PAGE OF DOC.: # 000 U.S. Patent No.,,0 Automotive Data Solutions Inc. 0 WIRE DESCRIPTION 0 pin Purple BCM near A pillar, driver side 0 pin Blue BCM near A pillar, driver side B0 pin Yellow BCM near A pillar, driver side M pin 0 White Passenger kick panel M 0 pin Gray BCM near A pillar, driver side M 0 pin White BCM near A pillar, driver side B0 pin LtBlue BCM near A pillar, driver side M White pin 0 Red Driver kick panel POSITION TYPE M M COLOR NAME COMPONENT LOCOR - LOCION - POLARITY Versa Note YEAR MODEL Sentra WIRE COLOR NISSAN MAKE TYPE - WIRE CHART - OF FLC-NI(RS)-NI-[FLRSNI]-EN
PAGE OF DOC.: # 000 TYPE - WIRING DIAGRAM - OF OBDII (UNDER DRIVER SIDE DASH) VS A G RF PORT/WEBLINK PORT B F TELEMIC PORT PIN OBDII E C VS D 0 PIN OBDII HARNESS MS A MS BRAKE SWITCH RELAY VS PIN BRAKE E VS B VS VS MS PIN VS VS VS0 ENGINE VS IMMO PIN IMMO 0 0 BROWN/BLACK 0 GRAY - RAP SHUTDOWN OUTPUT 0 EMPTY 0 EMPTY 0 EMPTY 0 PURPLE/GREEN - LOCK OUTPUT 0 EMPTY 0 BLUE/GREEN 0 EMPTY 0 EMPTY GRAY/GREEN - HORN OUTPUT DKGREEN/GREEN - UNLOCK OUTPUT VS PIN IMMO HARNESS WHITE PARKING LIGHT SEE WIRE CHART OPTIONAL HORN BCM B0 B0 DRIVER DOOR PIN - D 0 ACC O PIN HARNESS VS C CK N E PIN BRAKE HARNESS 0 0 LO 0 0 GRAY/WHITE - HOOD STUS INPUT M LOCK/ARM - UNLOCK/DISARM - M WITHOUT OEM HOOD SWITCH: INSTALL AND CONNECT TO AFTERMARKET HOOD SWITCH B0 M AFTERMARKET HOOD SWITCH 0 0 0 0 U.S. Patent No.,,0 Automotive Data Solutions Inc. 0 FLC-NI(RS)-NI-[FLRSNI]-EN
PAGE OF DOC.: # 000 PROGRAMMING PROCEDURE - OF 0 When programming, only one keyfob will be used. Place the other one at least 0 feet away from the vehicle. 0 Wait, LED will turn solid RED. Remove valet key from keyfob. 0 Wait until the key symbol light flashes. (This may take up to seconds.) Wait, LED will flash GREEN rapidly. HOLD 0 Push start button once [x] to OFF position. ACC ON ENGINE 0 Remove battery from keyfob. 0 Press and release brake pedal once [x]. WARNING: Disconnect power last. Disconnect module from vehicle. >> IMPORTANT: Place and hold keyfob on push to start button for steps to. 0 Wait, LED will turn solid GREEN. Connect module to computer and proceed with extended programming. Place and hold keyfob on push to start button (no battery). Keyfob transponder is located behind keyfob logo. 0 Wait until the key symbol light flashes. (This may take up to seconds.) Connect power first. Connect module to vehicle. Push start button twice [x] to ON position. Press and release brake pedal once [x]. >> IMPORTANT: Place and hold keyfob on push to start button for steps to. 0 ACC K C LO O N E N N GI 0 ACC ON ENGINE U.S. Patent No.,,0 Automotive Data Solutions Inc. 0 FLC-NI(RS)-NI-[FLRSNI]-EN
PROGRAMMING PROCEDURE - OF ACC K C LO PAGE OF DOC.: # 000 Place and hold keyfob on push to start button (no battery). Keyfob transponder is located behind keyfob logo. O N E N N GI Wait until the key symbol light turns OFF. Push start button twice [x] to ON position. ACC ON ENGINE 0 Wait, LED will turn solid GREEN for seconds. Push start button once [x] to OFF position. ACC ON ENGINE Module Programming Procedure completed. U.S. Patent No.,,0 Automotive Data Solutions Inc. 0 FLC-NI(RS)-NI-[FLRSNI]-EN
VALET MODE PROGRAMMING PROCEDURE - OF >> NOTE: In Valet Mode, the Remote starter is not functional. Keyless entry, Lock and Unlock will remain functional. See RF kit user manual for alternate valet mode programming. 0 Time restriction. Complete next step within seconds. 0 OFF ACC ON >> PAGE OF DOC.: # 000 To exit valet mode: repeat steps to. Cycle ignition ON five times [x OFF/ON] rapidly. ENGINE 0 0 Wait, LED will turn solid RED for seconds. Set ignition to OFF position. OFF ACC ON ENGINE 0 Valet Mode Programming Procedure completed. U.S. Patent No.,,0 Automotive Data Solutions Inc. 0 FLC-NI(RS)-NI-[FLRSNI]-EN
AFTERMARKET REMOTE PROGRAMMING - OF PAGE OF DOC.: # 000 AFTERMARKET REMOTE PROGRAMMING: NOTES I All aftermarket remotes must be programmed to the RF-Kit. Refer to the RF-Kit user guide for aftermarket remote features and programming procedures. U.S. Patent No.,,0 Automotive Data Solutions Inc. 0 FLC-NI(RS)-NI-[FLRSNI]-EN
PAGE OF DOC.: # 000 NAVIGION PROCEDURE - OF >> It is mandatory to exit the Module Navigation at the end of this procedure. Failure to exit the Module Navigation will drain vehicle battery. To exit the Module Navigation at any time: Follow STEP. 0 >> Module must be programmed to the vehicle. 0 >> Use the Module Navigation Chart on the next page. 0 Set ignition to OFF position. 0 TO ACCESS THE MENUS: Press and hold programming button until LED turns solid GREEN. 0 IN THE MENUS: Press the programming button as many times as the menu number indicates. LED will flash GREEN an equal amount of times continuously. 0 0 OFF ACC ON TO ACCESS THE OPTIONS: Press and hold programming button until LED turns solid RED. 0 IN THE OPTIONS: Press the programming button as many times as the option number indicates. LED will flash RED an equal amount of times continuously. TO ACCESS THE SETTINGS: Press and hold programming button until LED turns solid GREEN. Configure every other setting and proceed to step. [Z] LED will flash GREEN as many times as the current (or default) setting number, continuously. MANDORY: EXIT NAVIGION. Press and hold programming button for seconds. LED will flash RED rapidly. Release programming button. LED will turn OFF. [Z] IN THE SETTINGS: Press the programming button as many times as necessary to access your setting. LED will flash GREEN an equal amount of times continuously. Module navigation completed. To return to the MENUS: exit the Module Navigation and redo the Module Navigation Procedure. >> Failure to exit the Module Navigation will drain vehicle battery. [Y] To save and return to the OPTIONS: Press and hold programming button until LED turns solid RED. [Y] LED will flash RED as many times as the current option number continuously. ENGINE 0 0 [X] U.S. Patent No.,,0 Automotive Data Solutions Inc. 0 FLC-NI(RS)-NI-[FLRSNI]-EN
PAGE OF DOC.: # 000 [Y] OPTIONS [X] MENUS NAVIGION CHART: NOTES I Default settings are listed in bold. 0 II Make sure the option is covered on the vehicle before attempting to change the setting. 0 0 0 DISARM/UNLOCK BEFORE RELOCK AFTER RELOCK AFTER SHUTDOWN FORCE UNLOCK ALL ON FIRST PRESS 0 TAKEOVER 0 0 0 [Z] SETTINGS NAVIGION CHART - OF FACTORY KEYLESS RS SEQUENCE CONFIGURION 0 0 RUN TIME WAIT TO DELAY 0 OFF 0 ON 0 OFF 0 ON 0 OFF 0 ON 0 OFF 0 ON 0 ENABLE 0 DISABLE* 0 0 DISABLE 0 0 LOCK + UNLOCK + LOCK 0 LOCK + LOCK + LOCK 0 0 MIN 0 0 MIN 0 0 MIN 0 MIN 0 MIN 0 0 MIN 0 MIN 0 MIN 0 0 SEC 0 0 SEC 0 0 SEC 0 0 SEC 0 SEC 0 0 SEC 0 SEC 0 0 SEC 0 0 0 0 0 *Vehicle will shutdown when a door is opened. U.S. Patent No.,,0 Automotive Data Solutions Inc. 0 FLC-NI(RS)-NI-[FLRSNI]-EN
PAGE 0 OF DOC.: # 000 [Y] OPTIONS [X] MENUS NAVIGION CHART: NOTES 0 [Z] SETTINGS NAVIGION CHART - OF HORN EVENT TRIGGER CONFIGURION 0-0 Technical Support only 0 HORN CHIRPS WIDTH 0 DOUBLE LOCK 0 LOCK + UNLOCK 0 LOCK + UNLOCK + 0 DOUBLE LOCK + 0 0 msec 0 msec 0 0 msec 0 *Vehicle will shutdown when a door is opened. U.S. Patent No.,,0 Automotive Data Solutions Inc. 0 FLC-NI(RS)-NI-[FLRSNI]-EN
[X] NUMBER OF PARKING LIGHT FLASHES DIAGNOSTIC REMOTE ER ERROR CODES - OF I WARNING: The following applies only when the parking lights are connected and supported by the system. 0 Foot brake is ON. 0 Hood is open. II After a remote starter failure, the parking lights will flash [X] number times to indicate an error code. See table. 0 Engine tach signal is lost. 0 System is in Valet Mode. 0 Vehicle is moving (VSS). 0 Glow plug timeout error. 0 RS not synchronized. Start vehicle with OEM key for sec before trying a new RS sequence. 0 CAN communication failure during RS sequence. REMOTE ER ERROR CODES: NOTES U.S. Patent No.,,0 Automotive Data Solutions Inc. 0 FLC-NI(RS)-NI-[FLRSNI]-EN PAGE OF DOC.: # 000
I II III DURING PROGRAMMING DURING REMOTE WITH IGNITION OFF U.S. Patent No.,,0 Automotive Data Solutions Inc. 0 DIAGNOSTIC TEST LED STUS DIAGNOSTICS - OF Flashing RED Missing/wrong information from firmware or vehicle. Solid RED Module waiting for more vehicle information. Flashing GREEN Additional steps required to complete module programming. Solid GREEN then OFF Module correctly programmed. OFF No activity or module already programmed. Flashing RED Module incorrectly programmed. Solid RED Module incorrectly programmed. Flashing GREEN Module correctly programmed and operational. Solid GREEN then OFF Reset in progress. OFF Invalid ground when running status from remote starter. Flashing RED Module incorrectly programmed or connected. Solid RED Module not programmed. Waiting for more vehicle information. Flashing GREEN False ground when running status from remote starter. Solid GREEN then OFF Reset in progress. OFF Module at rest and ready for a remote start sequence. FLC-NI(RS)-NI-[FLRSNI]-EN PAGE OF DOC.: # 000
RESET PROCEDURE - OF 0 Disconnect all connectors from module except the BLACK 0-PIN connector. 0 Reconnect all connectors. 0 Disconnect the BLACK 0-PIN connector. 0 Repeat programming procedure. 0 PRESS AND HOLD the module s programming button while connecting the BLACK 0-PIN connector. >> Failure to follow procedure may result with a DTC or a CHECK ENGINE error message. 0 Wait, LED will flash RED. RELEASE programming button. 0 LED will turn RED for seconds. 0 Module RESET completed. U.S. Patent No.,,0 Automotive Data Solutions Inc. 0 FLC-NI(RS)-NI-[FLRSNI]-EN PAGE OF DOC.: # 000
TAKEOVER PROCEDURE - - OF >> All vehicle doors must be closed and locked prior to remote start sequence. 0 Take over procedure completed. 0 Time restriction. Complete steps to within seconds. >> Failure to follow procedure will result in vehicle engine shutdown. 0 Press unlock on OEM or aftermarket remote. 0 Open driver door and enter vehicle. 0 Close driver door. 0 Press and release BRAKE pedal. U.S. Patent No.,,0 Automotive Data Solutions Inc. 0 FLC-NI(RS)-NI-[FLRSNI]-EN PAGE OF DOC.: # 000
INSTALLION CHECKLIST - OF PAGE OF DOC.: # 000 CHECKLIST WARNING: Vehicle engine will start many times. Test in a well ventilated area. Close all vehicle doors, hood and trunk. Press the LOCK button once [x] on the aftermarket keyfob. Press the / button once [x] on the aftermarket keyfob to shut down vehicle. Question : Does the vehicle shut down? Question : Do the doors lock? YES: Go to next step. NO: Repeat step. If problem persists, press the brake pedal once [x] to shut down the vehicle and call technical support. RAP and auto light shutdown test YES: Go to next step. NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists. 0 Press the UNLOCK button once [x] on the aftermarket keyfob. YES: Go to next step. NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support if the problem persists. Question : Do the doors unlock? Question : Did the radio, interior controls and headlights turn off within 0 seconds after remote start shutdown? YES: Go to next step. NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists. Open hood. If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step. Press the TRUNK release button once [x] on the aftermarket keyfob if supported. Press the / button once [x] on the aftermarket keyfob to remote start vehicle. Question : Does the trunk or hatch open/unlock? Question : Does the vehicle remote start? YES: Close trunk or hatch and go to next step. NO: Verify the remote programming, the RF connections and the wired trunk/hatch connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists. Press the AUX button once [x] on the aftermarket keyfob if supported. Enter vehicle and close the doors. Question : Does the driver side sliding door open? Press the / button once [x] on the aftermarket keyfob to remote start vehicle. YES: Press the AUX button once [x] to close the driver sliding door and go to next step. Wait for the vehicle to start. NO: Verify the remote programming and the RF connections. Repeat the test and call technical support, if the problem persists. Press brake pedal. Press the AUX button once [x] on the aftermarket keyfob if supported. YES: Go to next step. YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test. NO: Go to next step. Close hood. Question 0: Does the vehicle shut down? Question : Does the passenger side sliding door open? YES: Press the AUX button once [x] to close the passenger sliding door and go to next step. NO: Verify the remote programming and the RF connections. Repeat the test and call technical support, if the problem persists. NO: The module does NOT detect the brake pedal signal. Press the / button once [x] on the aftermarket keyfob to shut down vehicle, check connection as illustrated in the wiring diagram, if applicable, and call technical support. Exit vehicle. Press the / button once [x] on the aftermarket keyfob to remote start vehicle. 0 Installation checklist completed. Question : Does the vehicle remote start? YES: Go to next step. NO: Verify the remote programming, the RF connections and check the remote start error codes. Repeat the test and call technical support, if the problem persists. U.S. Patent No.,,0 Automotive Data Solutions Inc. 0 FLC-NI(RS)-NI-[FLRSNI]-EN