4 SIDE STEPS PARTS LIST: 1 Driver/left Side Step 13 8-1.25mm x 25mm Hex Bolts 1 Passenger/right Side Step 13 8mm x 24mm x 2mm Flat Washers 1 Passenger/right Upper Bracket (all incl. DEF) 13 8mm Lock Washers 1 Passenger/right Lower Bracket (all incl. DEF) 1 8mm Bolt Plate 5 Mounting Brackets (use for left or right) 1 8mm Nylon Lock Nut (use w-bolt plate) 11 8-1.25mm Clip-On Nuts 12 8mm x 25mm Combo Bolts Left or Right Mounting Brackets 8mm Bolt Plate Passenger/right front only Upper Mounting Bracket Passenger/right front only Lower Mounting Bracket Left or Right Mounting Brackets Driver/left Side Step PROCEDURE: REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION. ASSISTANCE IS RECOMMENDED. ON MODELS WITH DEF TANK, SELECT A FLAT, LEVEL AREA FOR INSTALLATION. MAY REQUIRE CUTTING. 1. Start the installation under the driver side of the vehicle. Locate the 5 tabs along the bottom edge of the body, (pinch weld). Mounting Brackets will bolt to the 1st, 2nd, (just in front of center of cab), and 5th mounting tabs, (Figure 1). Directly above each tab is a top mounting location on the side of the body panel. Hold a Bracket up in place to help determine the mounting holes to use along the body. 2. Determine the correct procedure for your model year and each Bracket location. Bottom mounting location on the edge of the pinch weld. Flat tab on pinch weld with factory installed weld nut: Thread hex bolt into weld nut from the backside-down to clear paint from threads, (Figure 2). Flat tab on pinch weld with hole: Select (1) 8mm Clip Nut. Slide the Clip Nut over the tab with the nut facing up behind the tab, (Figures 3 5). Line up threaded nut with hole in tab. Repeat for each mounting location. Top mounting location on the side of the body panel. Models with factory installed threaded insert in body panel: Thread 8mm Hex Bolt into threaded insert to clear paint as required, (Figures 2 & 3). Large and small hole in side of body panel: Remove the rubber plug from the larger hole, (Figure 4). Select (1) 8mm Clip Nut. Slide the Clip Nut into the larger hole. Line up the threaded nut with the smaller hole, (Figure 5). 3. Select (1) Mounting Bracket. NOTE: (5) Brackets are universal and will fit left or right side. Bolt the Mounting Bracket to the Clip Nuts and/or the factory threaded holes with (2) 8mm Hex Bolts, (2) 8mm Lock Washers and (2) s, (Figures 6 & 7). Snug but do not fully tighten the hardware. 4. Repeat Steps 1 3 to install the (2) remaining driver side Brackets, (Figure 7). Page 1 of 6
4 SIDE STEPS 5. Select the driver/left Side Step. Carefully position the Driver Side Step onto the (3) Mounting Brackets. IMPORTANT: Do not slide the Side Step on the Brackets or damage to the finish may result. Attach the Side Step to the Mounting Brackets with (6) 8mm x 25mm Combination Hex Bolts, (Figure 16). Do not tighten hardware. 6. Level and adjust the Side Step and tighten all hardware. 7. Move to the passenger side of the vehicle. On the passenger side, determine if the vehicle is equipped with a plastic diesel exhaust fluid (DEF) tank, (Figures 8 & 9). Models without DEF tank, skip to Step 8. Models with DEF tank: The tank sits close to the side of the body. With specialized tools, the passenger front upper and lower Bracket can be installed but room is limited. It may be easier to drop the tank down to access the inner side of the body panel for upper bracket installation. Tank will not need to be removed, only dropped down for access to mounting location. IMPORTANT: If tank is full, it will be very heavy and assistance is highly recommended to avoid injury or damage to the vehicle or the tank. It is recommended that installation is performed when the DEF tank is low on fluid before dropping the tank. a. On models with plastic lower tray under the tank, remove the (3) hex bolts attaching the tray to the frame, (Figure 8), and remove tray. 2017 2500/3500 models: Remove the (4) hex bolts attaching the plastic cover to DEF tank, (Figure 9A) and remove the plastic cover, (Figure 9B). b. Release the tank filler hose. Release the plug for the sending unit on the top of the tank. c. Support the tank with a floor jack. Place a smooth flat surface, (wooden block for example), between the floor jack and the tank to avoid damaging the plastic tank. Do not push up on the tank; only support the weight of the tank with the jack. d. Remove the (2) bolts securing the tank straps to the vehicle, (Figure 10). Tilt the straps to release from the brackets. Slowly lower the tank until the top of the tank is almost visible. Use blocks or stands to support the tank while installing the front Upper and Lower Brackets. e. Proceed to Step 8. 8. Locate the first tab on the edge of the pinch weld on the passenger side, (Figures 2 4, 12 & 14). Select the Upper Bracket, (Figure 11). Repeat Steps 2 & 3 to attach the passenger front Upper Bracket to the side of the body panel, (Figure 12). Do not tighten hardware at this time. 9. Line up the hole in the bottom of the Upper Bracket with the hole in the tab on the pinch weld. a. Models with a weld-nut: Slide the Bracket over the weld-nut, (Figure 12). Attach the Lower Bracket to the bottom of the body and weld-nut with (1) 8mm x 25mm Hex Bolt, (1) 8mm Lock Washer and (1), (Figures 15 & 16). Leave loose at this time. b. Models with flat tab and hole: Insert the 8mm Bolt Plate down through the hole in the Upper Bracket and mounting tab, (Figures 13 & 14). Attach the Lower Bracket to the bottom of the body and Bolt Plate with (1) and (1) 8mm Nylon Lock Nut, (Figures 15 & 16). Leave loose at this time. 10. Line up the side tab on the Lower Bracket with the threaded hole in the side of the Upper Bracket. Attach the Lower Bracket to the Upper Bracket with (1) 8mm x 25mm Hex Bolt, (1) 8mm Lock Washer and (1), (Figure 16). Leave loose at this time. 11. Repeat Steps 1 3 for the (2) remaining passenger side Bracket installations. NOTE: Cradles on Brackets installed on passenger side will face forward. a. 2017 2500/3500 DEF tank models: Locate the 2nd tab bracket location along the bottom edge of the body, (pinch weld), (Figure 17). Hold the DEF cover in place and mark the 2nd Bracket location onto the cover, (Figure 18). Use a sharp knife or hacksaw blade to carefully cut a slot in the plastic cover to clear the 2nd Bracket, (Figure 19). Remove as little plastic as possible. 12. Repeat Steps 5 & 6 to install the passenger Side Step, (Figure 20). 13. Once the Side Steps are installed and all hardware fully tightened, reinstall the DEF tank and cover, if equipped, as described in Steps 7 & 11. 14. Do periodic inspections to the installation to make sure that all hardware is secure and tight. To protect your investment, wax this product after installing. Regular waxing is recommended to add a protective layer over the finish. Do not use any type of polish or wax that may contain abrasives that could damage the finish. Page 2 of 6
4 SIDE STEPS For stainless steel: Aluminum polish may be used to polish small scratches and scuffs on the finish. Mild soap may be used also to clean the Side Step. For gloss black finishes: Mild soap may be used to clean the Side Step. Driver/Left Side Installation Pictured Factory 8mm threaded insert in body panel 8mm Weld Nut (Fig 1) Driver side (3) mounting locations Factory 8mm threaded insert in body panel (Fig 2) Passenger side front mounting location Remove plug 8mm Clip Nut Rear (Fig 3) Driver side 2nd mounting location (2) 8mm Clip Nuts (Fig 4) Driver side rear mounting location (2) 8mm x 25mm Hex Bolts (2) 8mm Lock Washers (2) s Rear (Fig 5) Driver side rear mounting location (Fig 6) Driver/left front bracket installed Page 3 of 6
Driver/Left Side Installation Pictured 4 SIDE STEPS Rear (2) 8mm x 25mm Hex Bolts (2) 8mm Lock Washers (2) s (Fig 7) Driver/left rear bracket installed (Fig 8) 07-16 Passenger side front pictured with DEF tank cover. Remove (3) hex bolts to remove cover (Fig 9B) 2017 Passenger side DEF cover (Fig 9A) 2017 Passenger side pictured with DEF plastic tank cover. Remove (4) hex bolts to remove plastic cover Remove (2) factory bolts to remove tank straps (Fig 10) 07-16 Passenger side DEF tank and cover (Fig 11) Passenger/right Upper Bracket (all models) Page 4 of 6
Passenger/right Side Installation Pictured 4 SIDE STEPS 8mm x 25mm Hex Bolt 8mm Lock Washer (Fig 12) Slide Upper Bracket over weld nut if equipped-also see Figure 2 On models with flat tab (see Fig 3, 4 and 15), insert 8mm Bolt Plate (Fig 13) down through Upper Bracket and mounting tab (Fig 13) 8mm x 35mm Bolt Plate 8mm x 25mm Hex Bolt 8mm Lock Washer Fig 14 8mm Bolt Plate (Fig 15) Passenger/right Lower Bracket (all models) On models with flat tab and 8mm Bolt Plate (see Fig. 14) use: 8mm Nylon Lock Nut to attach Lower Bracket to Bolt Plate Models with weld nut on tab use: 8mm x 25mm Hex Bolt 8mm Lock Washer to attach Lower Bracket to weld nut Fig 16 Page 5 of 6
Passenger/right Side Installation Pictured 4 SIDE STEPS mark pictured is approximately 70mm x 10mm (Fig 19) Passenger side 2nd bracket location from back of body panel (Fig 18) 2017 Passenger side DEF cover marked for trimming (Fig 19) 2017 Passenger side DEF cut for example only (2) 8mm x 25mm Combo Bolts (Fig 20) Passenger/right center bracket installed Complete Installation Page 6 of 6