Alarms & Remote Start Automotive Data Solutions Inc. VW3 OL-AL(MDB)-VW3-EN AVAILABLE FOR : OL-MDB-ALL Rev. Date: March 04, 06 Doc. No.: ##757## U.S. PATENT NO. 8,856,780 The brand names and logos found in this guide are property of their respective owners. Automotive Data Solutions Inc. 06! NOTICE: The manufacturer will accept no responsibility for any electrical damage resulting from improper installation of this product, be that either damage to the vehicle itself or to the installed device. This device must be installed by a certified technician. This guide has been written for properly trained technicians; a certain level of skill & knowledge is therefore assumed. Please review the Installation Guide carefully before beginning any work.
Page of 6 Doc. No.: ##757## 060304 INSTALL TYPE SELECTION VolksWaGEN porsche TacHoMETEr output E-BrakE output BrakE pedal status output TrUNk status output HooD status output* Door status output TrUNk/HaTcH release DIsarM oem alarm arm oem alarm Door UNlock Door lock priority UNlock INsTall TypE year MoDEl audi MakE FEaTUrEs A8 04-0 S8 04-0 03-05 06-0 Phaeton 04-06 03-06 07-0 *Available only if vehicle is equipped with factory hood switch. Automotive Data Solutions Inc. 06
Page 3 of 6 Doc. No.: ##757## 060304 VolksWaGEN porsche Phaeton 06-0 04-06 03-06 07-0 polarity MoDUlE location component locator 03-05 WIrE color position 04-0 connector TypE S8 connector color 04-0 connector NaME year A8 WIrE DEscrIpTIoN MoDEl audi MakE TYPE - WIRE CROSS REFERENCE CHART Automotive Data Solutions Inc. 06
Page 4 of 6 Doc. No.: ##757## 060304 TYPE - WIRING DIAGRAM REMOTE STARTER TACH (AC) INPUT E-BRAKE STATUS (-) INPUT TRUNK (-) OUTPUT UNLOCK (-) OUTPUT LOCK (-) OUTPUT V (+) GROUND (-) GROUND WHEN RUNNING (-) OUTPUT <- OPTIONAL REQUIRED -> REQUIRED -> REQUIRED -> OPTIONAL -> OPTIONAL -> IGNITION (+) INPUT/OUTPUT BRAKE STATUS (+) INPUT HOOD STATUS (-) INPUT TRUNK STATUS (-) INPUT DOOR STATUS (-) INPUT DATA MODE N/A LEGEND NOT REQUIRED IN DATA MODE (-WAY) NOT REQUIRED IN DATA MODE (-WAY) USE DATA MODE OR HARDWIRE MODE LOCK/ARM (-) INPUT - GREEN/BLACK UNLOCK/DISARM (-) INPUT - BLUE/BLACK TRUNK (-) INPUT - RED/WHITE (NC) BROWN (NC) PURPLE/YELLOW (NC) PURPLE/BLACK (NC) WHITE (NC) BLACK/WHITE E-BRAKE STATUS (-) OUTPUT - GREEN TACH (AC) OUTPUT - PURPLE/WHITE WHITE/BLACK (NC) WHITE/RED (NC) WHITE (NC) YELLOW/BLACK - DOOR STATUS (-) OUTPUT YELLOW/RED - TRUNK STATUS (-) OUTPUT YELLOW - HOOD STATUS (-) OUTPUT BROWN/RED - CANH BROWN/YELLOW - CANL ORANGE/BLACK (NC) ORANGE/WHITE (NC) ORANGE - BRAKE (+) OUTPUT PINK/BLACK (NC) PINK - IGNITION (+) INPUT BLUE/RED (NC) BLUE/YELLOW (NC) GREEN/RED (NC) GREEN/YELLOW (NC) GRAY/RED (NC) GRAY/YELLOW (NC) TWISTED WIRES IN DOOR HARNESS, IN DRIVER KICK PANEL CA CA NH NL -O -O RA RA NG NG E/ E/B LT R. G OW N RE EN DATA MODE GWR (-) INPUT - BLUE/WHITE (NC) WHITE GROUND - BLACK V (+) - RED Automotive Data Solutions Inc. 06
Page 5 of 6 Doc. No.: ##757## 060304 INSTALLATION MODE SELECTION Press and release programming button to select installation mode. LED flashes (X) once = DATA MODE LED flashes (X) twice = STANDARD HARDWIRE MODE! Press and hold programming button until LED turns solid GREEN to register selection. After registration, follow Factory Reset Procedure to change installation mode and restart this procedure. MODULE PROGRAMMING PROCEDURE Insert key into ignition. Turn key to ON position. 3 4 Wait, LED will turn solid GREEN for seconds. OFF Turn key to OFF position. ON 5 Module Programming Procedure completed. Automotive Data Solutions Inc. 06
Page 6 of 6 Doc. No.: ##757## 060304 IDENTIFY VEHICLE YEAR Locate the Vehicle Identification Number (VIN), identify the 0th character then match it to its corresponding year. Æ 43A5YN5TAL8D5R0X Æ a 980 l 990 y 000 a 00 B 98 M 99 00 B 0 c 98 N 99 00 c 0 D 983 p 993 3 003 D 03 E 984 r 994 4 004 E 04 F 985 s 995 5 005 F 05 G 986 T 996 6 006 G 06 H 987 V 997 7 007 H 07 J 988 W 998 8 008 J 08 k 989 X 999 9 009 k 09 MODULE DIAGNOSTICS led status DIaGNosTIcs DUrING programming DUrING remote start WITH IGNITIoN off Flashing RED Missing/wrong information from firmware or vehicle Incorrectly programmed Incorrectly programmed or connected Solid RED Waiting for more vehicle information Incorrectly programmed Not programmed waiting for more vehicle information Flashing GREEN Additional steps required to complete programming Correctly programmed and operational False ground when running status from remote starter Solid GREEN then OFF Correctly programmed Reset in progress Reset in progress OFF No activity or already programmed Invalid ground when running status from remote starter At rest and ready for a remote start sequence LED will turn solid red for seconds. RESET COMPLETED. 6 3 4 RECONNECT all connectors. DISCONNECT black 4-PIN standard or optional data connector. 5 DISCONNECT all connectors from module EXCEPT the black 4-PIN standard or optional data connector. FACTORY RESET PROCEDURE PRESS AND HOLD programming button while connecting either 4-PIN standard or optional data connector. 7 Repeat programming procedure.! Failure to follow procedure may result with a DTC or a CHECK ENGINE error message. When LED flashes red, RELEASE programming button. Automotive Data Solutions Inc. 06