Compact integration of guide rods and a fine lock cylinder with a built-in locking mechanism

Courtesy of CM/Flodyne/Hydradyne Motion Control Hydraulic Pneumatic Electrical Mechanical (800) 6-80 www.cmafh.com Guide Cylinder Series MLGC uilt-in Fine Lock Cylinder Compact Type Compact integration of guide rods and a fine lock cylinder with a built-in locking mechanism % weight reduction using a new guide body (In comparison with MLGCL-0) Locking in both directions is possible. Locking in either side of cylinder stroke is possible, too. Maximum piston speed: 0 mm/s It can be used at to 0 mm/s provided that it is within the allowable kinetic energy range. ir cushion is standard. Enables the impact to be absorbed at the stroke end when the cylinder is operated at high speeds. Cylinder position can be detected. uilt-in magnet for auto switches is provided in all models. Three-types of locking mechanism Locking method Features Spring locking Pneumatic locking Spring and pneumatic locking Discharging the unlocking air causes the lock to operate. Supplying a pressure to the pressurized locking port enables the change of holding force as desired. Supplying a pressure to the pressurized locking port enables the change of holding force as desired. Discharging the unlocking air causes the lock to operate. 6 CLJ CLM CLG1 CL1 MLGC CNG MN CN CNS CLS CLQ LQ MLU MLGP ML1C D- -X

Courtesy of CM/Flodyne/Hydradyne Motion Control Hydraulic Pneumatic Electrical Mechanical (800) 6-80 www.cmafh.com M L F MLGC L 0 E MW earing type Slide bearing all bushing bearing Mounting asic Front mounting flange Guide Cylinder (uilt-in Fine Lock Cylinder Compact Type) Guide Cylinder/uilt-in Fine Lock Cylinder Compact Type Series MLGC ø, ø, ø, ø ore size mm mm mm mm E P D How to Order Nil ear plate Without rear plate With rear plate Locking method Spring locking (Exhaust locking) Pneumatic locking (Pressure locking) Spring and pneumatic locking pplicable uto Switches/efer to pages 183 to 0 for further information on auto switches. Type eed auto switch Solid state auto switch Indicator light None Yes None Yes None Yes Yes Port thread type M x 0.8 Nil c TN NPT For bore size and, M x 0.8 is only available. Cylinder stroke efer to Standard Stroke on page 1. Number of auto switches Nil S n uto switch Nil pcs. 1 pc. n pcs. Without auto switch (uilt-in magnet) C uto switch mounting bracket Note) Note) This symbol is indicated when the D- or M type auto switch is specified. This mounting bracket does not apply to other auto switches (D-C and H, etc.) (Nil) For applicable auto switch models, refer to the below table. Made to Order For details, refer to page 1. Load voltage uto switch model Lead wire length (m) Special Electrical Wiring Pre-wired pplicable function Perpendicular In-line entry (Output) 0. 1 3 None DC C connector load ø to ø ø, ø ø ø (Nil) (M) (L) (Z) (N) 3-wire (NPN) MNV MN IC V, V Grommet 3-wire (PNP) MPV MP circuit MV M -wire V Connector HC Diagnostic 3-wire (NPN) MNWV MNW IC indication V, V 3-wire (PNP) V MPWV MPW circuit elay, (-color PLC indication) -wire V MWV MW Water Grommet 3-wire (NPN) MNV MN IC resistant V, V 3-wire (PNP) MPV MP circuit (-color indication) -wire V MV M -wire (NPN) V, V HNF IC circuit With diagnostic output (-color indication) 3-wire IC (NPN equivalent) V 6V 6 circuit 0 V 3V 3 Grommet 0 V or less 0V 0 IC circuit 0 V, 0 V () V elay, -wire V 0 V or less (6) 6 PLC Connector C3C V or less C80C IC circuit Diagnostic indication Grommet (W) W (-color indication) Water resistant type auto switches can be mounted on the above models, but in such case SMC cannot guarantee water resistance. Consult with SMC regarding water resistant types with the above model numbers. Lead wire length symbols: 0. m Nil (Example) MNW Solid state auto switches marked with are produced upon receipt of order. 1 m M (Example) MNWM 3 m L (Example) MNWL m Z (Example) MNWZ None N (Example) HCN Since there are other applicable auto switches than listed, refer to page for details. Caution For details about auto switches with pre-wired connector, refer to pages 1 and 161. When using auto switches shown inside ( ), stroke The D-(V)/M(V)/MW(V)/M(V) are shipped together, (but not assembled). end detection may not be possible depending on (Only switch mounting bracket is assembled at the time of shipment.) the One-touch fitting or speed controller model. Please contact SMC in this case. 0

Courtesy of CM/Flodyne/Hydradyne Motion Control Hydraulic Pneumatic Electrical Mechanical (800) 6-80 www.cmafh.com Symbol Made to Order (For details, refer to pages 0 to 1.) Symbol Specifications Tapped hole, drilled hole, pin hole -XC machined additionally Guide Cylinder uilt-in Fine Lock Cylinder Compact Type Model/Specifications Model/Stroke Model (earing type) MLGCM (Slide bearing) MLGCL (all bushing bearing) ore size Standard stroke, 0, 1, 1, 0 0, 300, 3, 0 3, 0,, 0, 0, 1, 1 3, 0,, 0, 0 0, 0, 300 3, 0,, 0, 0, 00, 800 Intermediate strokes and short strokes other than the above are produced upon receipt of order. Specifications OUT Operating pressure (MPa) 0. 0. 0.3 0. 0. 0.6 8 OUT OUT OUT OUT 3 1 80 6.8 8. 1. 1 38 6 16 1 6 630 188 8 6 IN IN IN IN 6 61.8 8. 138. 318 6 6 1 6 36 30 18 1 636 Note) Theoretical output (N) = Pressure (MPa) x Piston area (mm ) Long stroke Model MLGC MLGC MLGC MLGC ase cylinder CDLG1 ore size Thread type Stroke Locking method uto switch ore size ction Fluid Proof pressure Maximum operating pressure Minimum operating pressure mbient and fluid temperature Piston speed 1 Cushion ase cylinder lubrication Stroke length tolerance Double acting ir 1. MPa 1.0 MPa 0. MPa (Horizontal, No load) to C to 0 mm/s ir cushion Non-lube +1. +0. mm Non-rotating Slide bearing ±0.06 ±0.0 ±0.0 ±0.0 accuracy all bushing bearing ±0.0 ±0.0 ±0.0 ±0.0 Piping port size 3 Cylinder port M x 0.8 (c, NPT) Lock port Locking method Spring locking (Exhaust locking) Pneumatic locking (Pressure locking) Spring and pneumatic locking 1 Constraints associated with the allowable kinetic energy are imposed on the speeds at which the piston can be locked. The maximum speed of mm/s can be accommodated if the piston is to be locked in the stationary state for the purpose of drop prevention. When the cylinder is retracted (initial value), the non-rotating accuracy without loads or deflection of the guide rods will be below the values shown in the above table as a guideline. 3 For bore size and, M x 0.8 is only available. Fine Lock Specifications Locking method Fluid Maximum operating pressure Unlocking pressure Lock starting pressure Locking direction Theoretical Output ore size od size Operating Piston area direction (mm ) Spring locking (Exhaust locking) Spring and pneumatic locking ir 0. MPa 0.3 MPa or more 0. MPa or less oth directions Series MLGC 18 3 88 63 8 88 Pneumatic locking (Pressure locking) 0.1 MPa or more 0.0 MPa or less 0.8 1 11 33 330 63 3 88 IN 0. 83 38 31 6 1130 Unit: N 1.0 3 6 1 80 61 1 CLJ CLM CLG1 CL1 MLGC CNG MN CN CNS CLS CLQ LQ MLU MLGP ML1C D- -X

Courtesy of CM/Flodyne/Hydradyne Motion Control Hydraulic Pneumatic Electrical Mechanical (800) 6-80 www.cmafh.com Series MLGC Weight (kg) ore size L type (all bushing bearing/asic). 3..0. LF type (all bushing bearing/ Front mounting flange) 3..8.01 8.6 M type (Slide bearing/asic) MF type (Slide bearing/front mounting flange) dditional weight with rear plate dditional weight per each mm of stroke dditional weight for long stroke.8 3. 0. 0.1 0.01 3.86.83 0.3 0. 0.01 3.8. 0.3 0.3 0.0.06 8.6 0.88 0. 0.03 asic weight Calculation: (Example) MLGCL-0--D (all bushing bearing/asic, ø/0 st., with rear plate) asic weight.0 (L type) dditional weight with rear plate 0.3 dditional stroke weight 0.3/ st Stroke 0 st dditional weight for long stroke 0.0.0 + 0.3 + 0.3 x 0/ + 0.0 =. kg llowable Kinetic Energy when Locking ore size llowable kinetic energy (J) ore size Holding force (N) 0.6 16 0. 313 0.6 3 Note) Holding force at piston rod extended side decreases approximately 1%. 1.1 In terms of specific load conditions, the allowable kinetic energy indicated in the table above is equivalent to a % load ratio at 0. MPa, and a piston speed of 300 mm/sec. Therefore, if the operating conditions are below these values, calculations are unnecessary. 1. pply the following formula to obtain the kinetic energy of the load. EK: Kinetic energy of load (J) 1 EK = mυ m: Load mass (kg) (Load mass + Moving parts weight) υ: Piston speed (m/s) (verage speed x 1.). The piston speed will exceed the average speed immediately before locking. To determine the piston speed for the purpose of obtaining the kinetic energy of load, use 1. times the average speed as a guide. 3. The relation between the speed and the load of the respective tube bores is indicated in the diagram below. Use the cylinder in the range below the line.. In order to insure the proper braking force, even within a given allowable kinetic energy level, there is an upper limit to the size of the load. Thus, a horizontally mounted cylinder must be operated below the solid line, and a vertically mounted cylinder must be operated below the dotted line. Load mass (kg) Piston speed (mm/s) Holding Force of Spring Locking (Max. static load) 8 Moving Parts Weight (kg) ore size Moving parts basic weight dditional weight with rear plate dditional weight per each mm of stroke 0. 0. 0.18 1.0 0.3 0.8 1.03 0.3 0. 1. 0.88 0.6 Calculation: (Example) MLGCL-0--D Moving parts basic weight 1.03 dditional weight with rear plate 0.3 dditional stroke weight 0./ st Stroke 0 st 1.03 + 0.3 + 0. x 0/ =.6 kg Holding Force of Pneumatic Locking (Max. static load) Holding force (N) ir pressure applied to pressurized locking port (MPa) 1. The holding force is the lock s ability to hold a static load that does not involve vibrations or shocks, after it is locked without a load. Therefore, to use the cylinder near the upper limit of the constant holding force, be aware of the following: If the piston rod slips because the lock s holding force has been exceeded, the brake shoe could become damaged, resulting in a reduced holding force or shortened life. To use the lock for drop prevention purposes, the load to be attached to the cylinder must be within 3% of the cylinder s holding force. Do not use the cylinder in the locked state to sustain a load that involves impact. Stopping ccuracy (Not including tolerance of control system) Locking method Spring locking (Exhaust locking) Pneumatic locking (Pressure locking) Spring and pneumatic locking ±0. ±0. Condition/ Load: % of thrust force at 0. MPa Solenoid valve: mounted to the lock port Piston speed (mm/s) 0 300 ±0. ±1.0 ±0.3 ±0. 0 ±.0 ±1. Caution ecommended Pneumatic Circuit/Caution on Handling For detailed specifications about the fine lock cylinder CLG1 series, refer to pages 0 to 0.

Courtesy of CM/Flodyne/Hydradyne Motion Control Hydraulic Pneumatic Electrical Mechanical (800) 6-80 www.cmafh.com Construction: With ear Plate ^0 ^3 % ^ %8 @6 @ @ @3 ^ ^8 &3 @ @1 ^6 ^ ^ #1 &1 & Front mounting flange # e # r #8! @0!6!8! #6 @8 u # @ #0 # q! o i!!1!0! #!3 # %0 Component Parts No. 1 3 6 8 11 13 rake spring 1 1 18 1 1 3 6 8 30 31 33 3 3 36 3 38 Description od cover Tube cover Cover Intermediate cover Piston rod Piston rake piston rake arm rake shoe oller Pin etaining ring ushing ushing Manual lock release cam Cam guide Lock nut Flat washer etaining ring Hexagon socket head bolt Spring washer Hexagon socket head bolt Spring washer Hexagon socket head bolt Spring washer Wear ring Wear ring Hexagon socket head plug Element od end nut Piston seal Piston gasket od seal od seal rake piston seal Intermediate cover gasket Cam gasket Material luminum alloy luminum alloy Carbon steel luminum alloy Carbon steel luminum alloy Carbon steel Carbon steel Special friction material Carbon steel Carbon steel Stainless steel Spring steel wire earing alloy earing alloy Chromium molybdenum steel Carbon steel Stainless steel Chromium molybdenum steel Steel wire Chromium molybdenum steel Steel wire Chromium molybdenum steel Steel wire esin esin Carbon steel ronze N N N N N N N Note) ^1, & are not required for without rear plate. LOCK FEE ^ Dacrodized Guide Cylinder uilt-in Fine Lock Cylinder Compact Type t &0 Note Clear hard anodized Hard anodized Nitrided Clear hard anodized Hard chrome plated ø, ø are stainless steel. Chromated Nitrided Nitrided Nitrided Heat treated % $ y #3 # % ^1 & @ $ %1 $3 %3 w For spring locking, spring/ pneumatic locking Nitrided, Nitrided, painted Type E only $1 %0 $ # % $0 Component Parts No. 3 1 3 6 8 1 3 6 8 61 6 63 Guide rod 6 6 66 6 68 6 0 1 3 all bushing bearing Long stroke Description Cylinder tube gasket Head cover Cylinder tube Cushion valve Cushion valve Seal retainer Cushion ring Cushion ring Valve retainer Lock nut etaining ring Cushion seal Cushion seal Cushion ring gasket Cushion ring gasket Valve seal Valve seal Valve retainer gasket Magnet Guide body Small flange Large flange Front plate ear plate Slide bearing all bushing bearing End bracket Washer Spring washer Felt Holder Type C retaining ring for hole Grease nipple Hexagon socket head bolt Hexagon socket head bolt Guide bolt Hexagon socket head bolt Material N luminum alloy luminum alloy luminum alloy luminum alloy Chromium molybdenum steel Stainless steel Urethane Urethane N N N N N luminum alloy Series MLGC View - $ $ % View - Slide bearing Note % $ $8 $6 %6 ^ Clear hard anodized Hard anodized nodized nodized Zinc chromated Electroless nickel plated Electroless nickel plated Electroless nickel plated Clear anodized For basic For front mounting flange Cast iron earing alloy Carbon steel Platinum silver For slide bearing For ball bushing bearing Hard chrome plated For slide bearing High carbon chrome bearing steel Quenched, Hard chrome plated For ball bushing bearing Carbon steel Steel wire Felt Stainless steel Carbon tool steel Phosphate coated Chromium molybdenum steel Chromium molybdenum steel Chromium molybdenum steel Chromium molybdenum steel For cylinder mounting For large/small flange mounting For front plate mounting For rear plate mounting 3 CLJ CLM CLG1 CL1 MLGC CNG MN CN CNS CLS CLQ LQ MLU MLGP ML1C D- -X

Courtesy of CM/Flodyne/Hydradyne Motion Control Hydraulic Pneumatic Electrical Mechanical (800) 6-80 www.cmafh.com Series MLGC Dimensions asic: With rear plate MLGC--- Wθ I J View - P (c, NPT) Unlocking port Unlocked when pressurized N Z ore size ore size WH (Max.) x O through GK Standard Stroke ore size ore size M K L Stroke range, 0, 1, 1, 0 GD, 0, 1 1, 0, 0 300 GK 3. 6 6 6 T Without ear Plate U 1 GL. 11 Y 6 6 11 V 3 1 63 1 63 18 3 GQ X G C GQ GC C H M8 x 1. depth Q D LOCK FEE GD D I 3 G GL E J x øf through Counterbore øg ack side x H øs E 8 x F P (c, NPT) od end cylinder port P (c, NPT) Lock port for pressure lock (Plug with breathing hole for spring locking) Y + Stroke Z + Stroke K 80 L M N O M6 x 1 M8 x 1. M8 x 1. M8 x 1. øt P Note ) M x 0.8 M x 0.8 ear plate Q 11 U P (c, NPT) Head end cylinder port C D E F P Note 3) P Z C D E F G GC 11 13. 1 1 0 3 M6 x 1 depth M8 x 1. depth M8 x 1. depth 3 3 13 0 0 3. 6. 86. 31. 86. 31. 118 1 1 6.8 11 depth 8 8.6 depth 8.6 depth 8 30 1 1 1 M x 1. depth 1 3 80 10. 1 depth 3 M x 1. depth 18 M x 1. depth 18 0 0 1 1 8 M x 1. depth 1 8. 11 1 38 W WH Wθ X Y Z 3 30 30 6 18 6 30 3 1 6 8. 3 33 Long Stroke ore size Note 1) Dimensions marked with are not required for without rear plate. Note ) For bore size and, M x 0.8 is only available. c, NPT port are available for bore size or greater. Note 3) c, NPT port are available. Stroke range 0 to 0 3 to 0 3 to 0 3 to 800 1 Z 10 36 W S 6 31 38 V P

Courtesy of CM/Flodyne/Hydradyne Motion Control Hydraulic Pneumatic Electrical Mechanical (800) 6-80 www.cmafh.com Dimensions Front mounting flange: With rear plate MLGCF--- x O through H G x øk hole Wθ ore size ore size ore size ore size N I J I J View - Standard Stroke M K L Stroke range, 0, 1, 1, 0, 0, 1 1, 0, 0 300 GL. 11 WH 3 8. 33 Without ear Plate P (c, NPT) Unlocking port Unlocked when pressurized WH (Max.) GQ 8 Y 6 6 11 G L X GQ GC Q LOCK FEE GD G GL øs øt P (c, NPT) Head end cylinder port Z G H I J K L M N O P Note 3) P Z GC GD GK 11 13 13 1 8 1 M8 13 3. 8 3. 0 16 1 1 88 M8 3 0 86. 6 0 16 1 1 88 M8 3 0 86. 30 6 1 1 10 11 13 11 6 0 M 1 3 6 I J K L M N O P Note ) Q S T U V W 3 0 0 80 1 1 M6 x 1 M8 x 1. M8 x 1. M x 0.8 M x 0.8 6 31 38 1 1 1 3 63 63 6 6 8. 11 1 38 M8 x 1. 11 18 3 Wθ 30 30 X 30 3 3 Y 6 Z 18 1 Long Stroke ore size Note 1) Dimensions marked with are not required for without rear plate. Note ) For bore size and, M x 0.8 is only available. c, NPT port are available for bore size or greater. Note 3) c, NPT port are available. Guide Cylinder uilt-in Fine Lock Cylinder Compact Type P (c, NPT) Lock port for pressure lock (Plug with breathing hole for spring locking) Y + Stroke Z + Stroke Stroke range 0 to 0 3 to 0 3 to 0 3 to 800 P (c, NPT) od end cylinder port ear plate 1 Z 10 36 For x O Series MLGC U W GK Cutout window G N P V M Mounting dimensions I CLJ CLM CLG1 CL1 MLGC CNG MN CN CNS CLS CLQ LQ MLU MLGP ML1C D- -X

Courtesy of CM/Flodyne/Hydradyne Motion Control Hydraulic Pneumatic Electrical Mechanical (800) 6-80 www.cmafh.com uto switch model D-M(V) D-MW(V) D-M(V)... 13. Series MLGC uto Switch Mounting uto Switch Proper Mounting Position (Detection at Stroke End) and Its Mounting Height D-M D-M/MW D- D-H D-C/C8 D-G/K D-/6 D-G/K D-/8 uto Switch Proper Mounting Position ore size D- D-80 D-3C D-C/C8 D-(V) D-80C D-C3C D-G D-C80C D-K D-KC 3 6. (3) (31) (3) (3) (1) 6. 6.. 3 (31) (33) 8 (3) 8 8 8 11. (.). (.) 6. (3.). (38.) 3. (31.) 3. (31.). (33.) 8. (3.) D- D-6 1 1 1 1. (.) 1. (.) 1. (.). (31.) D-GW D-KW D-H D-HC D-GF D-W D-HW D-G D-H D-HNF. (8.). (8.). (30.). (3.) 6 6 6. (30.). (.). (36.) ( ): Values for long stroke Note) djust the auto switch after confirming the operating conditions in the actual setting. 6 Hs Hs Hs Hs 11.... 11 LOCK FEE LOCK FEE LOCK FEE D-K D-GNT D-G. 1. (30.) ()... uto Switch Mounting Height uto D-/8 switch D-C/C8 D-3C D-GW model D-M(V) D-H D-80C D-KW D-MW(V) D-C3C D-HW D-G/K D-GNT D-M(V) D-C80C D-KC D-/6 D-HNF D-(V) D-HC D-W D-H D-G D-G D-GF 1 () 1 () (33) 8. 8. 8. ore size Hs. 31 3. Hs. 30. 3 Hs. 33 3. uto switch D-C/C8 D-H uto switch D-/6 D-G/K uto switch D-/8 D-G/K D-K Hs. 30 33. 38

Courtesy of CM/Flodyne/Hydradyne Motion Control Hydraulic Pneumatic Electrical Mechanical (800) 6-80 www.cmafh.com Minimum Stroke for uto Switch Mounting uto switch model D-M/MW/ D-C/C80 D-H/HW/H/HNF D-C3C/C80C/HC D-3C/80C/KC D-/6/G/K D-W D-/80/G/K Operating ange uto switch model ore size D-M/MW.. D- D-/80 D-3C/80C D-C/C80 D-C3C/C80C D-/6 D-W D-G/K/KC D-H D-H/HW D-HNF 8 8 8 13 8 6 13 8. 8 D-HC D-G/K D-GW/KW D-GNT/G 8.. D-GF D-GN 3. 6 Since this is a guideline including hysteresis, not meant to be guaranteed (assuming approximately ±30% dispersion). There may be the case it will vary substantially depending on the ambient environment. n: Number of auto switches Number of auto switches mounted 1 pc. pcs. n pcs. Same surface Same surface + (n ) Note) 1 6 + (n ) + (n ) 6 + (n ) + (n ) + (n ) + (n ) [Mounting screws set made of stainless steel] The following set of mounting screws made of stainless steel is also available. Use it in accordance with the operating environment. (Please order the auto switch mounting bracket separately, since it is not included.) 3: For D-/6/G/K types : For D-C/C8/H types Note 3) efer to page 18 for details of 3. The D-H/G are set on the cylinder with the stainless steel screws above when shipped. When an auto switch is shipped independently, 3 or is attached. uto switch model D-M(V)/MW(V) D-(V) D-M(V) a Switch bracket b Switch holder c uto switch mounting band uto Switch Mounting Series MLGC Note) Mounting of auto switches uto switch model D-M/MW D-3 uto Switch Mounting racket/part No. ore size Note 1) M3-0 Note ) M3-0S Note 1) M3-0 Note ) M3-0S D-C/C80 D-C3C/C80C D-H/D-HW M-0 M-0 M-0 M-0 D-HNF/D-H D-/6/D-W D-G/K/D-GW/KW D-G/GF -01-0 - -0 D-GNT/D-GN D-/80/3C/80C D-G/K/KC M1-01 M1-0 M1- M1-0 Note 1) Set part number which includes the auto switch mounting band (M-) and the holder kit (J-1/Switch bracket: Transparent). Since the switch bracket (made from nylon) are affected in an environment where alcohol, chloroform, methylamines, hydrochloric acid or sulfuric acid is splashed over, so it cannot be used. Please consult SMC regarding other chemicals. Note ) Set part number which includes the auto switch mounting band (M-S/Stainless steel screw) and the holder kit (J-1/Switch bracket: White). Note 3) For the D-M (V) type auto switch, do not install the switch bracket on the indicator light. uto switch With auto switches Same surface The auto switch is mounted by slightly displacing it in a direction (cylinder tube circumferential exterior) so that the auto switch and lead wire do not interfere with each other. Less than to strokes Less than to strokes d uto switch mounting screw Note 1) M3-0 Note ) M3-0S Note 1) M3-0 Note ) M3-0S (1) J-1 is a set of a and b. J-1 (Switch bracket: White) J-1 (Switch bracket: Transparent) () M-(S) is a set of c and d. and (c) is mounted so that the projected part is on the internal side (contact side with the tube). Other than the applicable auto switches listed in How to Order, the following auto switches can be mounted. efer to pages 183 to 0 for detailed specifications. (Consult with SMC for the D-/80, D-3C/80C, D-G/K, D-KC.) Type Model Electrical entry Features eed D-C3, C6, 3, 3, 6 Grommet (In-line) D-C80, 80 Without indicator light D-3C Connector (In-line) D-80C Without indicator light D-H1, H, H, G, GP, K, G, K D-KC Grommet (In-line) Connector (In-line) Solid state D-HW, HNW, HPW, GW, GPW, KW Diagnostic indication (-color indication) D-G D-GNT Grommet (In-line) Water resistant With timer With pre-wired connector is also available with solid state auto switches. efer to pages 1 and 161 for details. Normally closed (NC = b contact) solid state auto switches (D-FG/FH) are also available. efer to page 111 for details. Wide range detection solid state auto switch (D-GN) is also available. efer to page 13 for details. CLJ CLM CLG1 CL1 MLGC CNG MN CN CNS CLS CLQ LQ MLU MLGP ML1C D- -X

Courtesy of CM/Flodyne/Hydradyne Motion Control Hydraulic Pneumatic Electrical Mechanical (800) 6-80 www.cmafh.com MLGC Protective cover installation example Cover mounting bolt ear plate Protective cover ear plate Protective cover Caution on Handling the Fine Lock Cylinder Caution Series MLGC Specific Product Precautions e sure to read before handling. efer to front matter 3 for Safety Instructions and pages 3 to for ctuator and uto Switch Precautions. Warning 1. Installing a protective cover (In the case of rear plate) During mounting, handling and operation, the rear plate makes reciprocating movements. Therefore, pay careful attention not to insert your hand, etc., between the cylinder and the rear plate. When you are going to fit this product to the outside of your equipment, take preventative measures such as installing a protective cover. 1. For details, make sure to refer to Fine Lock Cylinder (CLG1 series) on pages 0 to 0. 8 Cover mounting bolt Installations/djustment Caution 1. Use caution that no scratch or dent will be given to the slide part of the guide rod. ecause the outer circumference of the guide rod is manufactured with precise tolerances, even a slight deformation, scratch, or gouge can lead to faulty operation or reduced durability.. When fitting the guide body, use the guide body which has high flatness of the fitting surface. If the guide rod has twisted, operation resistance will become abnormally higher and the bearing will wear at an early stage, thereby resulting in poor performance. 3. Mount in locations where maintenance will be easy. Ensure enough clearance around the cylinder to allow for unobstructed maintenance and inspection work.. Do not adjust the rod stroke by moving the rear plates, as doing so will cause the rear plates to come into direct contact with the guide body or the bracket mounting bolt. The resulting impact cannot be absorbed easily, the stroke position cannot be maintained, and faulty operation may result.. Lubrication When you are going to oil the bearings, do so by using a nipple so that no foreign matter will be mixed. For the grease, we recommended using high-quality lithium soapbased grease no.. 6. Mounting orientation For ceiling mounting (the opening of the rear plate is downward.), the rear plate may interfere with the basic cylinder head end due to the deflection of guide rods. Please consult with SMC.. Fixing of base cylinder When the product is mounted and operated in a location with low rigidity, bending moment may be applied to the base cylinder by vibrations generated at the stroke end, causing damage to the cylinder. In such cases, install a support bracket to suppress the vibration of the body of the base cylinder or reduce the piston speed until the body does not vibrate at the stroke end.

Courtesy of CM/Flodyne/Hydradyne Motion Control Hydraulic Pneumatic Electrical Mechanical (800) 6-80 www.cmafh.com Guide Cylinder/Compact Type Series MGC ø, ø, ø, ø, ø Integration of guide rods and a base cylinder The modified small flange shape facilitates mounting of speed controllers. 1% weight reduction chieved by making the front plate, small flange and guide body more compact. The modified bracket shape allows the auto switch to be mounted in any position. Lightweight Weight 1% reduction (In comparison with MGCL-0) ir cushion is standard. Enables the impact to be absorbed at the stroke end when the cylinder is operated at high speeds. The modified small flange shape facilitates the mounting of fittings. Variations ore size Standard stroke 0 1 1 0 0 300 Space-saving Length % shorter Height 18% shorter (In comparison with MGG) Compact front plate and guide body Long stroke ore size Long stroke 0 300 3 0 0 0 00 800 00 00 Grease nipple offers easy lubrication for bearings. Models without rear plate are available. 3 MGJ -Z W MGQ MGG MGC MGF MGZ MGT D- -X

Courtesy of CM/Flodyne/Hydradyne Motion Control Hydraulic Pneumatic Electrical Mechanical (800) 6-80 www.cmafh.com M L ore size earing type Slide bearing all bushing bearing mm mm mm mm mm F MGC L 0 MW Port thread type Nil TN TF Mounting asic Front mounting flange M x 0.8 c NPT G For bore size and, M x 0.8 is only available. Grommet Connector Grommet Grommet None Yes Connector None Grommet Yes Guide Cylinder/Compact Type Series MGC ø, ø, ø, ø, ø V, V V 3-wire (NPN) V, V 3-wire (PNP) V -wire V 3-wire (NPN) V, V 3-wire (PNP) -wire V -wire (NPN) V, V Nil How to Order Cylinder stroke efer to Model/Stroke on page. ear plate Without rear plate With rear plate uto switch Without auto switch Nil (uilt-in magnet) For applicable auto switch models, refer to the below table. pplicable uto Switches/efer to pages 183 to 0 for further information on auto switches. Type eed auto switch Solid state auto switch Guide Cylinder (Compact Type) Special function Diagnostic indication (-color indication) Water resistant (-color indication) With diagnostic output (-color indication) Diagnostic indication (-color indication) Electrical entry Indicator light Yes Yes Yes None Wiring (Output) 3-wire (NPN) 3-wire (PNP) -wire Load voltage Lead wire length symbols: 0. m Nil (Example) MNW 1 m M (Example) MNWM 3 m L (Example) MNWL m Z (Example) MNWZ None N (Example) HCN Since there are other applicable auto switches than listed, refer to page for details. For details about auto switches with pre-wired connector, refer to pages 1 and 161. The D-(V)/M(V)/MW(V)/M(V) are shipped together, (but not assembled). (Only switch mounting brackets are assembled at the time of shipment.) DC C 3-wire (NPN equivalent) V 0 V 6V 3V 6 3 0 V or less 0V 0 0 V, 0 V () V -wire V 0 V or less (6) V or less (W) C3C C80C W C uto switch mounting bracket Note) Note) This symbol is indicated when the D- or M type auto switch is specified. This mounting bracket does not apply to other auto switches (D-C and H, etc.) (Nil) Number of auto switches Nil pcs. S 1 pc. n n pcs. uto switch model Lead wire length (m) pplicable bore size Pre-wired 0. 1 3 None pplicable load ø to ø ø, ø ø ø, ø connector (Nil) (M) (L) (Z) (N) Perpendicular In line MNV MPV MN MP IC circuit MV M HC MNWV MNW IC MPWV MPW circuit elay, PLC MWV MW MNV MN IC MPV MP circuit MV M HNF IC circuit Water resistant type auto switches can be mounted on the above models, but in such case SMC cannot guarantee water resistance. Consult with SMC regarding water resistant types with the above model numbers. 6 Made to Order efer to page for details. Solid state auto switches marked with are produced upon receipt of order. IC circuit IC circuit IC circuit elay, PLC Caution When using auto switches shown inside ( ), stroke end detection may not be possible depending on the One-touch fitting or speed controller model. Please contact SMC in this case.

Courtesy of CM/Flodyne/Hydradyne Motion Control Hydraulic Pneumatic Electrical Mechanical (800) 6-80 www.cmafh.com Symbol Symbol ir cushion Symbol Specifications -X With piping ports for grease Symbol -X6 -X13 -XC -XC6 -XC8 -XC -XC11 -XC13 -XC -XC3 -XC3 -XC6 -XC3 -XC -XC8 -XC Made to Order: Individual Specifications (For details, refer to page.) Made to Order (For details, refer to pages 0 to 1.) Specifications Heat resistant cylinder ( to 1 C) Low speed cylinder ( to mm/s) With heavy duty scraper Made of stainless steel djustable stroke cylinder/djustable extension type djustable stroke cylinder/djustable retraction type Dual stroke cylinder/single rod uto switch rail mounting style Fluororubber seal With coil scraper Larger throttle diameter of connecting port With knock pin holes uilt-in cylinder with lock (CDNG) With front plate for MGG uto switch mounting special dimensions at stroke end Tapped hole, drilled hole, pin hole machined additionally Model/Specifications Model/Stroke Model (earing type) MGCM (Slide bearing) MGCL (all bushing bearing) 8 OUT IN OUT IN OUT IN OUT IN OUT IN ore size Standard stroke Long stroke, 0, 1, 1, 0 0, 300, 3, 0 3, 0,, 0 3, 0,, 0, 0 3, 0,, 0, 0 00, 800, 00, 00, 0, 1, 1 3, 0,, 0, 0 0, 0, 300 00, 800 Intermediate strokes and short strokes other than the above are produced upon receipt of order. Specifications Model ase cylinder ore size ction Fluid Proof pressure Maximum operating pressure Minimum operating pressure mbient and fluid temperature Piston speed Cushion ase cylinder lubrication Stroke length tolerance 1 Non-rotating Slide bearing accuracy all bushing bearing Piping port size (c, NPT, G) Theoretical Output ore size od size Guide Cylinder/Compact Type Series MGC Operating Piston area direction (mm ) 3 6 1 80 61 1 MGC MGC MGC MGC MGC CDG1 ore size Port thread type Stroke uto switch ±0.0 ±0.06 M x 0.8 OUT Double acting ir 1. MPa 1.0 MPa 0.1 MPa (Horizontal, No load) to C to mm/s ir cushion Non-lube +1. +0. mm ±0.06 ±0.06 ±0.0 ±0.0 ±0.0 ±0.0 Operating pressure (MPa) 0. 6.8.8 8. 8. 1 138 3 330 0.3.. 1 38 318 88 0. 6 6 16 6 8 6 0. 1 1 6 6 36 630 30 80 8 0.6 188 18 8 1 6 636 1180 0 0. 18 3 88 63 8 88 130 10 0.8 1 11 33 330 63 3 88 10 Note) Theoretical output (N) = Pressure (MPa) x Piston area (mm ) IN 0. 83 38 31 6 1130 1 0 ±0.0 ±0.0 1/ 1 When the cylinder is retracted (initial value), the non-rotating accuracy without loads or deflection of the guide rods will be below the values shown in the above table as a guideline. For bore sizes and, M x 0.8 is only available. (N) 1.0 3 6 1 80 61 1 MGJ -Z W MGQ MGG MGC MGF MGZ MGT D- -X

Courtesy of CM/Flodyne/Hydradyne Motion Control Hydraulic Pneumatic Electrical Mechanical (800) 6-80 www.cmafh.com Series MGC Weight ore size L type (all bushing bearing/asic) LF type (all bushing bearing/front mounting flange) M type (Slide bearing/asic) MF type (Slide bearing/front mounting flange) dditional weight with rear plate dditional weight per each mm of stroke dditional weight for long stroke dditional weight with bracket asic weight Moving Parts Weight (kg) ore size Calculation: (Example) MGCL-0- Moving parts basic weight dditional weight with rear plate 0.3 0. 0.3 0. 0.6 0.3 1. 0.8. 1.0 Moving parts basic weight 0.6 dditional weight with rear plate 0.3 dditional stroke weight 0./ st. dditional weight per each mm of stroke 0.11 0. 0. 0.33 0.1 Stroke 0 st. 0.6 + 0.3 + 0. x 0/ = 3.03 kg llowable Kinetic Energy by ir Cushion Mechanism ore size Effective cushion length :, H:. :, H:.. 8. 11.8 : od end, H: Head end llowable kinetic energy (J) : 0.3, H: 0. : 0.6, H: 0.6 0.1 1.8 3. High kinetic energy generated by large loads and high speed operations can be absorbed by compressing air at the stroke end thus preventing shock and vibration being transmitted to the machine. The air cushion has not been designed to control the piston speed in the end regions of the stroke. The load kinetic energy can be obtained by the following equation: 6 Ek = M υa M + m υ υ = 1. υa (kg) Calculation: (Example) MGCL-0-1.0 1. 1.0 1.6 0. 0. 1..3 1.1. 0. 0.1.0 3.0.03.8 0.3 0. 3..0 3.6.6 0.8 0. 6. 8.8 6.3 8.8 1.0 0.61 (all bushing bearing/asic, ø/0 st., with rear plate, with bracket) asic weight.0 (L type) dditional weight with rear plate 0.3 dditional stroke weight 0./ st Stroke 0 st dditional weight for long stroke 0.0 dditional weight with bracket 0.01.0 + 0.3 + 0. x 0/ + 0.0 + 0.01 =. kg 0.01 0.011 0.01 0.018 0.0 0.01 0.03 0.031 0.06 0.061 Total load mass (kg) 0 ø ø ø ø ø P = 0. MPa 1 0 0 0 ush speed into cushion υ (mm/s) Extend upward from mm/s on the abscissa in the graph until crossing at the line of bore size. Extend leftward from the intersection to find the total load weight kg. Subtract the moving parts weight of 3.08 kg from this. (For moving parts, refer to Moving Parts Weight.) 6. kg will be obtained, which is equal to the maximum load weight. Caution In a horizontal application, pay attention to that the load weight should not exceed the allowable end load given on pages 36 to 0.

Courtesy of CM/Flodyne/Hydradyne Motion Control Hydraulic Pneumatic Electrical Mechanical (800) 6-80 www.cmafh.com ir-hydro Low pressure hydraulic cylinder of 1.0 MPa or less Through the concurrent use of the CC series air-hydro unit, it becomes possible to operate at a constant or low speed or to effect an intermediate stop, just like a hydraulic unit, while using pneumatic equipment such as a valve. MGCH earing type Mounting ore size Port thread type Stroke ir-hydro Specifications ore size,,,, ction Double acting Fluid Turbine oil Proof pressure 1. MPa Maximum operating pressure 1.0 MPa Minimum operating pressure 0.18 MPa (Horizontal, No load) Piston speed 1 to 300 mm/s Cushion None mbient and fluid temperature + to C Mounting asic Front mounting flange For specifications other than the above, refer to page. uto switch can be mounted. Front mounting flange ore size x P (c, NPT, G) P 1/ Y + Stroke 1 Y 81 8 With/Without rear plate Dimensions (Dimensions other than the below are the same as standard type.) Guide Cylinder/Compact Type Series MGC Series pplicable to Operating Environments that Do Not ccept Copper Copper and Fluorine-free Series For details, refer to the SMC website. MGJ -Z W MGQ MGG MGC MGF MGZ MGT D- -X

Courtesy of CM/Flodyne/Hydradyne Motion Control Hydraulic Pneumatic Electrical Mechanical (800) 6-80 www.cmafh.com Series MGC Slide earing llowable End Load and Deflection MGCM - Stroke - MGCM - Stroke - MGCM - Stroke - Deflection Y (Slide bearing type) MGCM - Stroke - Deflection Y MGCM - Stroke - Deflection Y 8 St: Stroke llowable end load F (N) F Y Deflection Y llowable end load F (N) llowable end load F (N) (Slide bearing type) St: Stroke llowable end load F (N) (Slide bearing type) St: Stroke (Slide bearing type) St: Stroke Deflection Y (Slide bearing type) St: Stroke llowable end load F (N)

Courtesy of CM/Flodyne/Hydradyne Motion Control Hydraulic Pneumatic Electrical Mechanical (800) 6-80 www.cmafh.com MGCL - Stroke - Deflection Y MGCL - Stroke - Deflection Y llowable end load F (N) MGCL - Stroke - Deflection Y (all bushing bearing type) F Y St: Stroke all ushing earing llowable End Load and Deflection MGCL - Stroke - MGCL - Stroke - Deflection Y llowable end load F (N) llowable end load F (N) Guide Cylinder/Compact Type Series MGC (all bushing bearing type) St: Stroke llowable end load F (N) (all bushing bearing type) St: Stroke (all bushing bearing type) St: Stroke Deflection Y (all bushing bearing type) St: Stroke llowable end load F (N) MGJ -Z W MGQ MGG MGC MGF MGZ MGT D- -X

Courtesy of CM/Flodyne/Hydradyne Motion Control Hydraulic Pneumatic Electrical Mechanical (800) 6-80 www.cmafh.com Series MGC MGCM - Stroke - Deflection Y (Slide bearing type) MGCM - Stroke - Deflection Y MGCM - Stroke - Deflection Y 0 St: Stroke llowable end load F (N) F Y Slide earing llowable End Load and Deflection MGCM - Stroke - MGCM - Stroke - Deflection Y llowable end load F (N) llowable end load F (N) (Slide bearing type) St: Stroke llowable end load F (N) (Slide bearing type) St: Stroke (Slide bearing type) St: Stroke Deflection Y (Slide bearing type) St: Stroke llowable end load F (N)

Courtesy of CM/Flodyne/Hydradyne Motion Control Hydraulic Pneumatic Electrical Mechanical (800) 6-80 www.cmafh.com MGCL - Stroke - Deflection Y MGCL - Stroke - Deflection Y llowable end load F (N) MGCL - Stroke - Deflection Y (all bushing bearing type) F Y St: Stroke all ushing earing llowable End Load and Deflection MGCL - Stroke - MGCL - Stroke - Deflection Y llowable end load F (N) llowable end load F (N) Guide Cylinder/Compact Type Series MGC (all bushing bearing type) St: Stroke llowable end load F (N) (all bushing bearing type) St: Stroke (all bushing bearing type) St: Stroke Deflection Y (all bushing bearing type) St: Stroke llowable end load F (N) 1 MGJ -Z W MGQ MGG MGC MGF MGZ MGT D- -X

Courtesy of CM/Flodyne/Hydradyne Motion Control Hydraulic Pneumatic Electrical Mechanical (800) 6-80 www.cmafh.com Series MGC llowable Eccentric Load L L Slide earing/ all ushing earing/ MGCM - Stroke - MGCL - Stroke - llowable eccentric load W (N) Eccentric distance from center of cylinder to load center of gravity L (Set the maximum allowable load so that it does not exceed the following percentages of the theoretical output: % for ø, % for ø and ø, % for ø and % or less for ø, respectively.) llowable eccentric load W (N) Eccentric distance from center of cylinder to load center of gravity L (Set the maximum allowable load so that it does not exceed the following percentages of the theoretical output: % for ø, % for ø and ø, % for ø and % or less for ø, respectively.)

Courtesy of CM/Flodyne/Hydradyne Motion Control Hydraulic Pneumatic Electrical Mechanical (800) 6-80 www.cmafh.com Construction: With ear Plate @ #8 #0 @ @8 r! #6 @ $1tq $3 @!@6 #1 # #3!8 y e! $ i!3 o!6 u! w # @ # @3 # $0 # View - Component Parts No. 1 3 6 8 11 13 1 1 18 1 1 3 6 8 30 Description od cover Tube cover Piston Piston rod ushing Cushion ring Cushion ring Magnet Seal retainer Cushion valve Valve retainer Lock nut Wear ring od end nut Cushion seal Cushion seal Piston gasket Cushion ring gasket Cushion ring gasket Head cover Cylinder tube Guide body Small flange Large flange Front plate ear plate Slide bearing all bushing bearing Guide rod End bracket Washer Spring washer Front mounting flange Material luminum alloy luminum alloy luminum alloy Carbon steel earing alloy luminum alloy luminum alloy esin Urethane Urethane N N N luminum alloy luminum alloy luminum alloy Cast iron earing alloy Carbon steel High carbon chrome bearing steel Carbon steel Steel wire Note) @, # are not required for without rear plate Slide bearing Note Clear hard anodized Clear hard anodized Chromated Hard chrome plated ø, ø are stainless steel. nodized nodized Nothing for long stroke Electroless nickel plated Electroless nickel plated Clear hard anodized For long stroke Hard anodized Clear anodized For basic For front mounting flange Platinum sliver For slide bearing For ball bushing bearing Hard chrome plated For slide bearing Quenched, hard chrome plated For ball bushing bearing Guide Cylinder/Compact Type Series MGC all bushing bearing @6 @1! y $3!8 @0 Long stroke Component Parts No. 31 33 3 3 36 3 38 3 1 3 Description Felt Holder Type C retaining ring for hole racket Nipple Hexagon socket head cap screw Hexagon socket head cap screw Guide bolt Hexagon socket head cap screw Hexagon socket head cap screw od seal Piston seal Tube gasket Valve seal Valve retainer gasket eplacement Parts/Seal Kit ore size Material Felt Stainless steel Carbon tool steel Stainless steel Chromium molybdenum steel Chromium molybdenum steel Chromium molybdenum steel Chromium molybdenum steel Chromium molybdenum steel N N N N N Kit no. CG1-PS CG1-PS CG1-PS CG1-PS View - Contents $!1!!0 $ Phosphate coated Note For cylinder mounting For large/small flange mounting For front plate mounting For rear plate mounting For bracket mounting Set of nos. above $1, $, $3, $, $ Seal kit includes $1 to $. Order the seal kit, based on each bore size. Seal kit includes a grease pack ( g). Order with the following part number when only the grease pack is needed. Grease pack part number: G-S-0 ( g) Caution When disassembling base cylinders with bore sizes of ø through ø, grip the double flat part of either the tube cover or the rod cover with a vise and loosen the other side with a wrench or an adjustable angle wrench, and then remove the cover. When retightening, tighten approximately degrees more than the original position. (Cylinders with ø or larger bore sizes are tightened with a large tightening torque and cannot be disassembled. Please contact SMC when disassembly is required.) 3 MGJ -Z W MGQ MGG MGC MGF MGZ MGT D- -X

Courtesy of CM/Flodyne/Hydradyne Motion Control Hydraulic Pneumatic Electrical Mechanical (800) 6-80 www.cmafh.com Series MGC Dimensions asic: With rear plate MGC-- ore size ore size I J N M K Stroke range, 0, 1, 1, 0 30 3 0 8. 0 80 11 Without ear Plate ore size Z 11 131 136 16 I, 0, 1 1, 0 0, 300 J K L L 80 1 1 80 8 130 M 38 6 ore size 11 1 3 N 38 Long Stroke 11 13 13 1 L X C O C Q M6 x 1 M6 x 1 M6 x 1 M8 x 1. M8 x 1. Stroke range 0 to 0 3 to 0 3 to 0 3 to 800 3 to 00 6. 6. 6. 0 1 D D C D E E Note ) P M x 0.8 M x 0.8 1/ 1 Y 81 8 Q 13 øs ore size E S 6 31 38 8 T 13 U 8 8 1 1 18 racket Mounting Stroke racket mounting stroke 0 st or more 1 st or more 1 st or more 0 st or more 0 st or more Note 1) Dimensions marked with are not required for without rear plate. Note ) For bore size and, M x 0.8 is only available. c, NPT and G ports are available for bore size or greater. View - WH (Max.) x O through x P (c, NPT, G) F M x 0.8 depth 30 M6 x 1 depth 3 M6 x 1 depth M8 x 1. depth M x 1. depth x øf through, counterbore øg ottom side x H racket (efer to the below table.) Y + Stroke Z + Stroke 8 x F L P 6 6 6 3 V 3 6 3 63 3 C W øt D 6 1 13 0 1 1 1. 1.. 80 E F 0.. depth 6 M6 x 1 depth 3 118 6.8 6.8 11 depth 8 11 depth 8 M8 x 1. depth M8 x 1. depth 1 10 8.6 depth M x 1. depth 18. 1 depth M x 1. depth 1 WH 3 6 8. 6 33. W ear plate U W X 30 3 30 6 6 6 6 G Y 1 1 3 80 Z 1 13 1 188 1 V P H

Courtesy of CM/Flodyne/Hydradyne Motion Control Hydraulic Pneumatic Electrical Mechanical (800) 6-80 www.cmafh.com Dimensions Front mounting flange: With rear plate MGCF-- H G ore size N I J I J x O through WH (Max.) View - ore size O M6 x 1 M6 x 1 M6 x 1 M8 x 1. M8 x 1. Without ear Plate ore size Z 11 131 136 16 M K Stroke range, 0, 1, 1, 0, 0, 1, 1 0, 0, 300 L x øk hole Note ) P M x 0.8 M x 0.8 1/ 80 8 130 Q 13 11 1 3 Long Stroke ore size L X 11 13 13 1 S 6 31 38 8 Q G H Stroke range 0 to 0 3 to 0 3 to 0 3 to 800 3 to 00 1 1 136 13 1 0 16 10 T 13 1 x P (c, NPT, G) U 8 8 1 1 18 I 8 1 11 V 3 6 3 63 3 J øs 0 6.6 0 8 1 13 11 W K WH L W M 6 8 X 6 6 3 8. 33. 30 30 3 6 6 6 6 ore size Y 1 1 3 80 racket mounting stroke 0 st or more 1 st or more 1 st or more 0 st or more 0 st or more øt N O P 1 1 1 0 M6 M8 M8 M8 M 3 Note 1) Dimensions marked with are not required for without rear plate. Note ) For bore size and, M x 0.8 is only available. c, NPT and G ports are available for bore size or greater. Y 81 8 Guide Cylinder/Compact Type Series MGC Y + Stroke Z + Stroke racket (efer to the below table.) racket Mounting Stroke For x O Z 1 13 1 188 1 ear plate U W 6 1 13 0 1 Cutout window I J P V G K 30 3 0 8. 0 80 11 N L M Mounting dimensions 80 1 1 M 38 6 I N 38 MGJ -Z W MGQ MGG MGC MGF MGZ MGT D- -X

Courtesy of CM/Flodyne/Hydradyne Motion Control Hydraulic Pneumatic Electrical Mechanical (800) 6-80 www.cmafh.com uto Switch Proper Mounting Position (Detection at Stroke End) and Its Mounting Height D-M(V)/MW(V) D-M(V) D-(V) D-H D-C/C8 D-G/K D-/6 D-G/K D-/8 uto Switch Proper Mounting Position uto switch model ore size 33 33 3 3 6 () () (33) (36) () 30 3 (8) (8) 1 () 3 () 8 () D-/80 D-C D-3C D-C80 D- D-80C D-C3C D-6 D-G/K D-C80C D-KC 30. 30. 31. 36. 3. 1. (.) 1. (.). (30.). (33.). (1.).. (8.). (8.) 1. (.) 3. (.) 8. (.). (.). (.) 1. (3.) 1. (6.). (3.) 1. (.) 1. (.) 18. (6.). (.). (3.) 1. (.) 1. (.). (8.). (31.). (3.) ( ): Values for long stroke, double rod Note) djust the auto switch after confirming the operating conditions in the actual setting. 6 Series MGC uto Switch Mounting D-M(V) D-MW(V) D-(V) D-M(V) Hs Hs Hs Hs. 30. 3.. 18 11.... 11 3. 3... 36. D-GF D-HW D-GW D-W D-H D-KW D-H D-G D-HC D-G D-HNF D-K 6. 6.. 3. 8. 8.. 3. 1. D-GNT 6 31 38 8. 8. 8. uto Switch Mounting Height uto switch model ore size () () 1 () 1 (8) (36) Hs. 31 3. 1 uto switch D-C/C8 D-H uto switch D-/6 D-G/K uto switch D-/8 D-G/K. 30. 3 D-M D-MW D-M D-MV D-MWV D- D-C/C80 D-MV D-V D-H D-HW D-HNF D-H Hs. D-C3C D-C80C Hs. 33 3. 3 D-/80 D-3C D-80C 30 D-G/K D-GW D-KW D-/6 D-G/K D-KC D-W D-HC D-G D-GNT D-GF Hs. 33. 38 3.

Courtesy of CM/Flodyne/Hydradyne Motion Control Hydraulic Pneumatic Electrical Mechanical (800) 6-80 www.cmafh.com Minimum uto Switch Mounting Stroke uto switch model D-M D-MW D-M D- D-MV D-V D-MWV D-MV D-C D-C80 D-H D-HW D-H D-HNF D-C3C D-C80C D-HC D- D-6 D-G D-K D-W Note 1) uto switch mounting uto switch model 1 pc. 3. Different surfaces 1 Note 1) 1 Note 1) 1 1 30 30 Different surfaces 1 No. of auto switches mounted pcs. The auto switch proper mounting position is 3. mm inward from the switch holder edge. Same surface Note 1) Note 1) Note 1) 30 Note 1) D-M Less than stroke Note ) D-MW D-M Less than stroke Note ) D- Note ) Minimum stroke for mounting auto switches in the other mounting styles mentioned in note 1. uto Switch Mounting Series MGC 3 3 0 80 0 With auto switches Different surfaces (n ) + 3 (n =,, 6 ) (n ) + 3 (n =,, 6 ) (n ) + 3 (n =,, 6 ) (n ) 1 + 3 (n =,, 6 ) (n ) + 3 (n =,, 6 ) (n ) 1 + 3 (n =,, 6 ) (n ) + 3 (n =,, 6 ) (n ) + (n =,, 6 ) (n ) + (n =,, 6 ) (n ) 30 + (n =,, 6 ) (n ) + (n =,, 6 ) (n ) 30 + (n =,, 6 ) Same surface n: No. of auto switches n pcs. Less than stroke Note ) Less than stroke Note ) Less than stroke Note ) Same surface + 3 (n ) + 3 (n ) + 3 (n ) + 3 (n ) 3 + 3 (n ) + 3 (n ) 3 + 3 (n ) + (n ) 0 + (n ) 80 + (n ) 0 + (n ) + (n ) The auto switch is mounted by slightly displacing it in a direction (cylinder tube circumferential exterior) so that the auto switch and lead wire do not interfere with each other. MGJ -Z W MGQ MGG MGC MGF MGZ MGT D- -X

Courtesy of CM/Flodyne/Hydradyne Motion Control Hydraulic Pneumatic Electrical Mechanical (800) 6-80 www.cmafh.com Series MGC Operating ange uto Switch model ore size D-M(V)/MW(V) D-M(V).. 6. D-(V) 6 8 8 8 D-/80 D-3C/80C 8 8 8 13 13 8. 6 8.. D-C/C80 D-C3C/C80C D-/6 D-W D-G/K/KC D-H/HW D-H/HNF D-HC D-G/K D-GW/KW D-GNT/G D-GF D-GN 3 Since this is a guideline including hysteresis, not meant to be guaranteed. (assuming approximately ± 30% dispersion) There may be the case it will vary substantially depending on an ambient environment... 6 6 uto Switch Mounting racket: Part No. uto Switch model D-M(V) D-MW(V) D-(V) D-M(V) D-C/C80 D-C3C/C80C D-H D-HW D-HNF D-H [Stainless Steel Mounting Screw] The following stainless steel mounting screw kit is available. Use it in accordance with the operating environment. (Since the auto switch mounting bracket is not included, order it separately.) 3: For D-,6,G,K types : For D-C,C80,H types Note ) efer to page 18 for details on the 3. The above stainless steel screws are used when a cylinder is shipped with the D-H/G auto switch. When an auto switch is shipped independently, 3 and are included. ø Note 1) M3-0 Note ) M3-0S M-0 a Switch bracket b Switch holder c uto switch mounting band ø Note 1) M3-0 Note ) M3-0S M-0 ore size ø Note 1) M3-0 Note ) M3-0S M-0 D-/6/W D-G/K D-GW/KW D-G/GF D-GNT/GN -01-0 - -0-0 D-/80 D-3C/80C M1-01 M1-0 M1- M1-0 M1-0 D-G/K/KC Note 1) Set part number which includes the auto switch mounting band (M-) and the holder kit (J-1/Switch bracket: Transparent). Since the switch bracket (made from nylon) are affected in an environment where alcohol, chloroform, methylamines, hydrochloric acid or sulfuric acid is splashed over, so it cannot be used. Please consult SMC regarding other chemicals. Note ) Set part number which includes the auto switch mounting band (M-S/Stainless steel screw) and the holder kit (J-1/Switch bracket: White). Note 3) For the D-M (V) type auto switch, do not install the switch bracket on the indicator light. uto switch d uto switch mounting screw For solid state auto switches, auto switches with a pre-wired connector are also available. efer to pages 1 and 161 for details. Normally closed (NC = b contact) solid state auto switches (D-FG/FH types) are also available. efer to page 111 for details. Wide range detection type, solid state auto switches (D-GN type) are also available. efer to page 13 for details. ø Note 1) M3-0 Note ) M3-0S M-0 ø Note 1) M3-0 Note ) M3-0S M-0 (1) J-1 is a set of a and b. J-1 (Switch bracket: White) J-1 (Switch bracket: Transparent) () M-(S) is a set of c and d. and (c) is mounted so that the projected part is on the internal side (contact side with the tube). esides the models listed in How to Order, the following auto switches are applicable. efer to pages 183 to 0 for detailed specifications. (Please contact SMC for D-/80, D-3C/80C, D-G/K, D-KC.) Type Model Electrical entry Features Solid state auto switch D-C3, C6, 3, 3, 6 Grommet (In-line) D-C80, 80 Without indicator light D-3C Connector (In-line) D-80C Without indicator light D-H1, H, H, G, GP, K, G, K D-KC Grommet (In-line) Connector (In-line) eed auto switch D-HW, HNW, HPW, GW, GPW, KW Diagnostic indication (-color indication) D-H D-GNT Grommet (In-line) Water resistant (-color indication) With timer 8