ir Cylinder Series NCM Now available in 8 different bore sizes, 7/16" to 2". 5 ctuation options available: Double cting, Single Rod Double cting, Double Rod Non-rotating Rod Single cting, Spring Return Single cting, Spring Extend wide variety of mounting configurations: ront Nose Mount Rear Pivot Mount Double End Mount Block Mount oot Mount (optional brackets) Chrome plated carbon steel piston rod improves corrosion resistance. Stainless steel 34 is available for further protection. vailable bumper for increased kinetic energy absorption, increased life cycles, and decreased noise. Piston is crimped to rod to achieve tighter clearances and reduce piston rod deflection. aluminum piston improves corrosion resistance. Magnetic actuated limit switches are available as a standard option. Seal, wear ring, and polished stainless steel tube work together to absorb side load and decrease overall friction, ensuring long lasting service life. (ear ring used on 3/4" bore and larger.) ull port design increases cylinder response. Rolled threads for increased strength. Clear anodized end covers provide long lasting protection against corrosion. Pre-lubricated at the factory means that the NCM does not require a lubricated air system. eatures 1
ir Cylinder: Standard Single cting, Spring Return/Extend Series NCM How to Order NC M B 75-1 -- M9B Nil D B C E Built-in magnet None Built-in magnet with auto switch ront nose mount Rear pivot mount Double end mount 75 88 16 125 15 3/4" 7/8" 1-1/16" 1-1/4" 1-1/2" Option hen ordering multiple options, refer to options compatibility page to ensure options availability. Nil None Stainless steel rod Note 3) XC6 X65 X163US Spring assist Note 4) Heavy duty spring Note 4) Number of auto switches Nil 2 pcs. S 1 pc. n n pcs. Standard stroke Inches Note 1) Stroke Hundredths of an inch (i.e. 6 =.6") Nil ithout C Note 2) bumper ction S T uto switch Nil ithout auto switch or applicable auto switch models, refer to the table on page 18. Spring return Spring extend Note 1) See specifications for standard and maximum stroke lengths. Note 2) is offered at no additional cost on ø7/8" and ø1-1/4". They are options on the other bore sizes. The C after the bore size must be included in either case. affects cylinder overall length of some models. Refer to the dimensional data. Note 3) Stainless steel rod standard on ø3/4" and ø7/8". Note 4) ø3/4", ø1-1/16" and ø1-1/2" only. 17
Specifications: Single cting, Spring Return / Spring Extend Specifications luid Maximum operating pressure Minimum operating pressure mbient and fluid temperature Piston speed ubrication ir 25 PSI / 1.7 MPa 25 PSI /.18 MPa 4 to 14 / 5 to 6 C 2 to 2 in/sec / 5 to 5 mm/s Optional (No additional charge on 7/8" and 1-1/4" bore) Not required (Pre-lubricated at factory) B, C, E, R Note) R mount available on 3/4", 1-1/16", and 1-1/2" bore only. Standard Stroke Standard stroke Max. stroke ront nose mount (B) Rear pivot mount (C) Double end mount (E) Block mount (R) Note) Up to 18" available as special request. 1/2, 1, 1-1/2, 2, 3, 4 6 Theoretical Output: Spring Return (S) with Standard Rod Rod diameter.312 Operating direction Effective area (sq.inch).442.68.882 1.227 1.767 Note1) orce on extension () is shown as the theoretical force of a double acting cylinder on extension less the compressed force of the return spring. Note 2) orce on retraction () is the resting force of spring when fully retracted. 25 8. 12.2 19.1 23.7 37.2 Theoretical Output: Spring Extend (T) with Standard Rod Rod diameter.312 Operating direction Effective area (sq.inch).393.559.86 1.77 1.617 5 19.1 27.4 41.1 54.4 81.4 Operating pressure (PSI) 75 1 3.1 41.2 42.6 57.8 63.2 85.2 85. 115.7 7. 125.5 169.7 7. Note1) orce on retraction () is shown as the theoretical force of a double acting cylinder on retraction less the compressed force of the extend spring. Note 2) orce on extension () is the resting force of spring when fully extended. 25 6.8 11. 17.2 19.9 33.4 5 16.6 25. 37.3 46.9 73.9 125 52.2 7 17.3 146.4 213.9 Operating pressure (PSI) 75 1 125 26.5 36.3 46.1 38.9 52.9 66.9 57.5 77.6 97.8 7. 73.8 1.7 127.6 7. 114.3 154.7 195.1 15 63.3 88.2 129.4 177.1 258.1 15 55.9 8.9 117.9 154.6 235.6 (lbf) (lbf) 19
Construction: Single cting, Spring Return Component Parts No. 1 2 3 4 5 6 7 8 9 1 11 Description Rod cover Head cover Cylinder tube Piston 3/4", 7/8" Piston rod 1-1/16", 1-1/4", 1-1/2" Bushing Piston seal Piston gasket Spring Spring guide Material Stainless steel Stainless steel Carbon steel Sintered Bronze Urethane NBR NBR Music wire Note Clear anodized Clear anodized Stainless steel 34 Hard chrome plated 21
Dimensions: Single cting, Spring Return ront nose mount / Spring return NCMB_-_S ZB1 + Per 1" of Stroke.9 NE NC -UN-2 D-cross lats NN- Nut (included) 1/8 NPT Double end mount / Spring return NCME_-_S Rear pivot mount / Spring return NCMC_-_S Y ZB + Stroke B + Stroke øg Pivot Pin Hole Y ZB + Stroke B + Stroke øg øg Pin GB N NN- Nut (incl. except 2" bore) D-cross lats -UN-2 MM.312 1/4-28 1/4-28 5/16-24 7/16-2 7/16-2 NN- Nut (incl. except 2" bore) B.496 4 4.749.749.3.3.3.3.3 D.38.38 E.86.93 1.12 1.32.38.38.38 G G.375 GB 1. Note 1) dimension for NCME15 not applicable. There are no flats on the E type 15 bore rear tang. Note 2) dimension for NCMC 15 is not applicable. There are no threads on the C type 15 bore rear tang. NCME 15 NN-UN-2 D-cross lats -UN-2 N.12.34.34.34.41 NC.88 1.6 1.25 NE.12.18.24 -UN-2 NN 1/2-2.44.88.88.78.78 1.69 1.81 1.69 Single cting, Spring Return (B/C/E) Mount without Magnet 2.28 2.35 3.12 B 1.5 1.72 2.6 2.44 Note) B dimension for NCME15 not applicable. ZB1 1.63 1.84 2.19 2.57 2.56 2.63 2.94 3.66 3.5 7 3.78 3.63 X155US (without clevis pin) øg.378 Single cting, Spring Return (B/C) Mount with Magnet B 2.59 2.91 3.5 1.63 1.84 2.19 2.56 ZB1 1.75 1.97 2.32 2.78 2.68 6 3.79 3.63 2.81 2.88 3.19 3.91 3.75 Single cting, Spring Return (E) Mount with Magnet B 2.59 2.91 3.5 6 3.79 2.81 2.88 3.19 3.91 3.5 23