Actuator LA7 Data sheet LINAK.COM/MEDLINECARELINE
LA7 The LA7 actuator is a powerful actuator designed for a variety of medical applications. It is developed for both push and pull applications and has a very robust construction because of the ultrasonic welded plastic housing. The LA7 actuator is equipped with a plug for connection of exchangeable cable with minifit connector. This gives the possibility to order standard actuators and combine them with different cable lengths. Features: 4V DC permanent magnet motor Thrust up to 6 N (in push application) Thrust up to 4N (in a pull application) Elegant and compact design with small installation dimensions Protection class: IPX4, IPX6 Colour: Light grey (RAL75) or dark grey (RAL 76) Builtin end stop switches (not adjustable) Possible to mount on control box CB6 with a special mounting clip (article no. 97 is delivered with CB6) Scratch and wear resistent powder painted steel inner tube. Brake ensures the selflocking ability in either push or pull directions.there will always be a reduction of the selflock characteristic when the actuator is run in the opposite direction to the brake direction Noise level 5dB (A), actuator not loaded Usage: Duty cycle: /8; minutes continuous use followed by 8 minutes not in use Ambient temperature: +5 o to +4 o C (the actuator must also be at this temp.) LA7 is approved according to IEC 66, ANSI/AAMI ES 66 and CAN/CSA C. No. 66 With connection to a static voltage power supply of V the lifetime could be reduced to 5 cycles (at a constant load of 6 N). LINAK.COM/MEDLINECARELINE
Technical specifications Combi code Generel Max load Typical amp. Speed Selflocking Actuator type Spindle type Back fixture Piston rod eye Option position Colour Safety option 7 X X X X Z X X BBB Z Z Z 7 S Z B Z BBB Z Z Z 5 5,8 5 5 75 7 S Z B Brake Stroke Length Motor type IP Degree Motor PCBA 5 5 6 6* 7 4 S Z B Z BBB Z Z Z 4 5 5 4,6,4 5 4 4 5 4 4 7 7 S Z B Z BBB Z Z Z 6 5,5,9 5 6,8 5 5 5* Z = No influence on technical data F = Flexible X = Influence on technical data M = Massive/Solid S = Standard * = See tabel for selflocking running opposite direction of brake direction BBB = See technical specification table above. Max BID (Build in Dimension) is 7 mm PITCH Z BBB Z Z Z 9 MAX STROKE MIN STROKE PUSH PULL Max current at max load Average current at max,8 load Minimum speed at max load Average speed, max load 4,5 5,5 45 5,5,7 Shortcircuit ON 5* 75 75 5 5* Spindle type Pitch (mm) Max. selflock (N) 9 4 4 7 6 5 5 Table. Reduced selflock characteristics when the actuator is run in the opposite direction.
Builtin dimensions (standard) Standard S + 7 mm Standard + Mechanical Spline S + 7 mm LA7 Ordering example, econ: 7 4 B 4 7 D Not used Not used = None = None Safety Factor: =. =.5 =.5 Cable: Plug Type: Fire Category: Install. Dim.: Brake: Option/Position: Piston Rod Eye: Back fixture: Colour: = None D = Minifit = V = V XXXX = mm = None = Brake PUSH = Brake PULL = None A = Internal QR**) K = High Load X = Other = With slot = Without slot = degrees = 9 degrees = Grey RAL75 = Dark grey RAL76 IP: Motor Type: Interface: Positionering: Safety: Stroke Length: Spindle Pitch: Actuator Type: 4 = IPX4 6 = IPX6 B = 4VDC. Normal X = Other Description = Analog*) = OpenBus X = None H = Hall = None A = Safety nut C = Mec. Spline D = Mec. Spline+Safety nut. J = Ratchet Spline K = Ratchet Spline + Safety nut XXX = mm = mm**) 4 = 4 mm 5 = 5 mm 6 = 6 mm 9 = 9 mm 7 = LA7 * Please contact your local LINAK contact regarding selflock ability **) QR and 8 N ( mm pitch) versions are not available for sale to new projects. We recommend to use LA4 QR or LA4 8 N.
Dimensions LA7 Drawing no.:la7b Dimensions LA7 with CB6: Drawing no.: CB6_LA7B
Back fixtures: SECTION AA A Type 6 Type 5 Type Type
Current (Amps) Current v s Thrust (typical values) Push with push brake 5 4,5 4,5,5,5,5 4 mm pitch mm pitch 5 mm pitch 6 mm pitch 9 mm pitch 4 6 8 Thrust (N) 8 N ( mm pitch) version not available for new projects. Speed v s Thrust (typical values) Push with push brake 4 9 mm pitch Speed (mm/s) 8 6 4 6 mm pitch 5 mm pitch 4 mm pitch mm pitch 4 6 8 Thrust (N) 8 N ( mm pitch) version not available for new projects. Copyright LINAK 8.. MA M94O. Chapter 5.4 Terms of use The user is responsible for determining the suitability of LINAK products for specific application. LINAK takes great care in providing accurate and uptodate information on its products. However, due to continuous development in order to improve its products, LINAK products are subject to frequent modifications and changes without prior notice. Therefore, LINAK cannot guarantee the correct and actual status of said information on its products. While LINAK uses its best efforts to fulfil orders, LINAK cannot, for the same reasons as mentioned above, guarantee the availability of any particular product. Therefore, LINAK reserves the right to discontinue the sale of any product displayed on its website or listed in its catalogues or other written material drawn up by LINAK. All sales are subject to the Standard Terms of Sale and Delivery for LINAK. For a copy hereof, please contact LINAK. FOR MOUNTING INSTRUCTIONS AND GUIDANCE IN USAGE, PLEASE SEE THE RELEVANT USER MANUAL