Manual LOGO 600 SE.

Manual LOGO 600 SE www.mikado-heli.de Mikado Model Helicopters GmbH Friedrich-Klausing-Straße 4469 Potsdam Germany phone +49 (0) 749-0 fax +49 (0) 749- www.mikado-heli.de Mikado Model Helicopters GmbH 05, V.009

Manual Mikado LOGO 600 SE Safety Instructions................. Tools for Assembly & R/C Equipment....... Mainframe..................... Tail Rotor..................... 4 Tail Boom..................... 5 4 Main Gear & Tail Boom Assembly........ 6 5 V-Bar Rotor Head................. 7 6 Servo Installation................. 8 7 Mounting the Motor................ 9 8 Canopy Mounting................. 9 9 Radio and Battery............... 0 0 Overview Chassis............... Overview Tail Rotor.............. Overview V-Bar Head............. Max. rotorhead rpm LOGO SX SE 600: 00 800 Max. collective range: +/- Max. Rotor blade size: 600 690 mm - 60 mm Max. LiPo Akku size: 0S 5000 mah Max. LiPo Akku size: S 00 mah Index LOGO 600 SE is not recommended for novices. This helicopter is a complex system. Basic knowledge of the function of a model helicopter is required to build and operate the LOGO 600 SE. Tools for Assembly & R/C Equipment Screwdrivers (plus and minus) 5 Minute Epoxy Ball link pliers 5 Minute Epoxy circlips pliers Threadlock Scissors Grease Note: There is no bag 4 and 0. The bags are numbered to, with the exception of 4 and 0. OPERATING YOUR MODEL SAFELY Operate the helicopter in spacious areas with no people nearby.!warning: Do NOT operate the helicopter in the following places and situations (or else you risk severe accidents): in places where children gather or people pass through in residential areas and parks indoors and in limited space in windy weather or when there is any rain, snow, fog or other precipitation If you do not observe these instructions you may be held reliable for personal injury or property damage! Always check the R/C system prior to operating your helicopter. When the R/C system batteries get weaker, the operational range of the R/C system decreases. Note that you may lose control of your model when operating it under such conditions. Keep in mind that other people around you might also be operating a R/C model. Never use a frequency which someone else is using at the same time. Radio signals will be mixed and you will lose control of your model. If the model shows irregular behavior, bring the model to a halt immediately. Turn off all power switches and disconnect the batteries. Investigate the reason and Safety Instructions fix the problem. Do not operate the model again as long as the problem is not solved, as this may lead to further trouble and unforeseen accidents.! Warning: In order to prevent accidents and personal injury, be sure to observe the following: Before flying the helicopter, ensure that all screws are tightened. A single loose screw may cause a major accident. Replace all broken or defective parts with new ones, as damaged parts lead to crashes. Never approach a spinning rotor. Keep at least 0 meters/yards away from a spinning rotor blades. Do not touch the motor immediately after use. It may be hot enough to cause burns. Perform all necessary maintenance. PRIOR TO ADJUSTING AND OPERATING YOUR MO- DEL, OBSERVE THE FOLLOWING!Warning: Operate the helicopter only outdoors and out of people s reach as the main rotor operates at high rpm!! Warning: While adjusting, stand at least 0 meters/ yards away from the helicopter! Novice R/C helicopter pilots should always seek advice from experienced pilots to obtain hints with assembly and for pre-flight adjustments. Note that a badly assembled or insufficiently adjusted helicopter is a safety hazard! In the beginning, novice R/C helicopter pilots should always be assisted by an experienced pilot and never fly alone! Rubber Hammer Alle shown products are examples. You may use different brands. Motor + Speed Controller (check the Mikado webpages for recommended motors) Battery V-Bar Hex Wrenches.5/.0/.5/.0 mm (.055/.079/.098/.8 in) Radio with Heli-Software Pitch Gauge Manual LOGO 600SE - Mikado Model Helicopters GmbH - Page

Mainframe Bag Bag 7x x7 M,5 SW5x59 x7x x 5x49 Before you combine the two sides of the main Using the rod M.5x40 from bag 7, position all frame, attach the two belt tensioners (#4089, 4 nylon nuts in the right side frame. bag 6). After assembling the chassis. please move the battery plate in to the frame. x7 x5x,5 Mx0 0x9x5 Mx6,6 M,5x8 M,5x0 9x M,5x6 M,5x Mx0 M,5x M,6 tapping screw Mx0 Mx6 Mx0 M,5x SW Ø5x59 M Stop M,5x0 M,5 Stop M,5x6 () M,5x8 Mx0 Mx6 raised head Ø5x49 All parts shown in the boxes are displayed in real size. M Stop Mx0 raised head You should position the motor pinion on the motor shaft, before you mount the motor plate. You may also mount the motor pinion at a later stage, but the process will be more cumbersome. For reading on how to mount the motor pinion, please flip to page 9. Manual LOGO 600SE - Mikado Model Helicopters GmbH - Page

Tail Rotor Beutel 5 Mx6 6x8x0,5 smaller inner Ø larger inner Ø 5x8x Apply grease Apply Loctite only in the threaded section inside the a on bearing b tail rotor hub! c M Stopp d Bag 5 6x8x0,5 Mx8 x0x7 Mx8 Mx5 (5x) M,5x6 Glue ball bearings using 5min. Epoxy 5xx4 5x8x 8x,5 Mx6 M x8 Mx 5x7x, 5x M Bag 5 M,5x6 5x7 Bag 5 7mm Mx8 5x Mx5 x5x5 x6x,5 Mx4 M8 x5x0,5 x5x5 M8 Kugel/ball/Rotule Ø4,8x x5x0,5 Mx4 x6x,5 7mm M Stopp (5x) x5x0 x0x7 5xx4 5x7x, Manual LOGO 600SE - Mikado Model Helicopters GmbH - Page 4

Tail Boom Bag 6 Bag Bag 6 Mx40 M M6 M Stop Mx6 Ball Ø6x mm Mx40 Bag 6 + Ø680 mm M6 5 Min. Epoxy Ball Ø6 mm Mx6 () M M Stop Bag 5 Mx Bag 6 + Ø5x50 mm 5 Min. Epoxy Ball Ø6 mm Attach the ball links so that the engraved number is on the outer surface pointing towards you. Manual LOGO 600SE - Mikado Model Helicopters GmbH - Page 5

4 Main Gear & Tail Boom Assembly Bag Bag Bag 8 Bag 4 For wider batteries, you may enlarge this cut-out. 0x6x0,5 x6 M,5x8 Tighten tooth belt: Pull tail rotor backwards and tighten screws Bag 8 Carefully push in... Do not damage the tail boom holders. M Mx Mx0 0x6x0,5 5 Mx0 Swashplate bag Mx8 M Stopp (4),6 Mx0 Attach the tail boom with a screw.6 To remove the battery, rotate locking mechanism until it locks. After inserting a battery, rotate back to secure the battery plate in place. Mx0 Tighten the pivot bolts very carefully. Do not overtighten them, as (7x) they will break off. Manual LOGO 600SE - Mikado Model Helicopters GmbH - Page 6

5 Servo Installation Bag Bag 9 LOGO Rotor Head (V-Stabi, flybarless head) 6 mm 6 mm Bag 4 4-6mm 6 mm Mx47 x5x,, () If you are installing Futaba servos, add the distance plate for the two aileron servos. Bag 9 5 M,5x0, M0 M Bag 9 9x x M M,5x5 M,5x0 () 6 (), () Bag Aileron right Elevator Rudder 7 Attach the ball links so that the engraved number is on the outer surface pointing towards you. Apply a small amount of oil to the rotor shaft. 8 mm Aileron left 9 Manual LOGO 600SE - Mikado Model Helicopters GmbH - Page 7

6 V-Bar Rotor Head LOGO 600SX Bag 7 Mx6 M5x 5x5x Small inner diameter Apply grease to bearing. Mounting direction is not critical.,5x5,8x0, Bag 7 8x6x5 Large inner diameter Center the spindle shaft exactly! 8x5x,6 Please supply silicon oil or grease on o-rings and spindle shaft! 6x 7x5 O-Ring 8x5x,6 8x6x5,5x5,8x0, 7x5 M5x 4 5 After mounting, the blade holders will move a little bit tightly at first. x 6 x7x 7 Mx Mx0 47 mm 8 x7x0, 8x6x5,5x5,8x0, Mx0 M Stopp Mx5 Mx4 Mx6 x6x,5 Mx5 x5x M5x M5 5x5x M Stop Mx5 9 M4 Stop Ø4,8x x x7x x6x,5 x5x x5x0, Mx4 Mx5 M,5x60 Mx Manual LOGO 600SE - Mikado Model Helicopters GmbH - Page 8

7 Mounting the Motor 8 Mounting the Canopy Bag Bag, For mounting the new motor counterbearing with rotorshaft suport, please follow these steps: First, mount the main gear, the rotor shaft assembly and all shims. Secure assembly with the 0 mm c-clip (Picture ). The main gear will have 0.5 mm axial play. This is normal and will facilitate the mounting and positioning of the pinion later on. Now mount the motor and the counterbearing. Once the motor position is set (please ensure correct gear backlash!), please screw the rotorshaft support onto the counterbearing, using the three Mx6 screws. x Mx8 6x9x0, Mx6 Bag M 0x6x0,5 Bag 6x9x0, 0x6x0,5 Bag 9 Mx0 M Please mount the motor, motor plate, pinion and counterbearing as illustrated in the above picture. When positioning the pinion, please ensure that it sits exactly on the ball bearing of the counterbearing with only one shim (6.9x0.) inbetween. Also make sure that the M4 set screw sits on the flattened area of the motor shaft. 5x0x 0x6x0,5 0x6x0,5 Installation of the Motor Pinion Screw the motor pinion onto the motor shaft, making sure that it can still be moved. Now mount the motor on the motor plate and move the pinion so it is aligned well with the main gear. As visual help for aligning the pinion you may use the small ridge which separates the two parts of the pinion. When the pinion is aligned correctly it will easily engage with the main gear. If the pinion does not engage with the main gear, it is not correctly aligned. After the pinion is correctly aligned, take the motor out of the mainframe and tighten the set screw. Gear Backlash Move the motor with the pinion until it is limited by the gear. Tighten one of the M screws slightly. You must still be able to swivel the motor around its own axis. In this way you can easily determine the correct distance between the main gear and the pinion. There should be no (!) gear backlash. At the same time, the motor should not (!) exert any pressure onto the running surface of the main gear. After you have determined the correct distance, tighten the second M screw. Manual LOGO 600SE - Mikado Model Helicopters GmbH - Page 9

9 Radio and Battery To adjust, leave the heli unpowered. The exact center position of the servo arm will be determined in the trim flight. Position for V-Bar gyro 4 Position for Mini V-Bar speed controller 5 Position of servo arms for the aileron servos when sticks are centered (0 deg. Pitch) Battery: Attach the battery with the velcro straps. Mount the battery in a position where the center of gravity is met with the battery holder installed. Velcro (adhesive) 6 7 Velcro Strap Manual LOGO 600SE - Mikado Model Helicopters GmbH - Page 0

0 Overview Chassis 8 49 40 4064 409 407 (0mm) 47 (mm) 9 64 (550) 49 4868 (600/690) 07 () 85 98 90 4089 9 40 46 495 00 (0x6x0,5) 009 (0x6x0,) 95 00 95 465 4094 M07-5 48 M-06, mm 46 M-06, mm 4099 499 94 49 4059 074 497 4067 958 49 44 494 490 954 4 white 775 black 974 46 (6mm Motorshaft) 474 (5mm Motorshaft) 90 490 black LOGO 500/600/690 488 white LOGO 500/600/690 Manual LOGO 600SE - Mikado Model Helicopters GmbH - Page

Overview Tail Rotor 45 96 477 47 069 077 407 465 447 464 445 04074 46 074 466 956 4669 77 444 EDGE 95 445 EDGE 05 460 074 464 460 47 4096 4670 4098 LOGO 600 454 LOGO 600 SE 407 LOGO 600 455 LOGO 600 SE 4097 (SET) LOGO 600 454 (SET) LOGO 600 SE 4648 408 (70XL LOGO 600) 45 (770XL LOGO 600 SE) Manual LOGO 600SE - Mikado Model Helicopters GmbH - Page

Overview V-Bar Head 974 95 074 980 04050 840 4708 574 4049 954 46 (Main rotor yoke for LOGO 600 SE) 076 845 467 468 90 96 408 586 (60mm) 579 (65mm) 0 4 565 www.mikado-heli.de 4 Construction & Rendering: Mehran Mahinpour Tirooni, André Doil Layout & Realisation: CDT, André Doil Manual LOGO 600SE - Mikado Model Helicopters GmbH - Page